Repair C:\Windows\System32\Logfiles\Srt\SrtTrail.txt loop
I recently bought an ASUS laptop with windows 8. The next day, I installed it says windows could not repair a system because of a file error.
(C:\Windows\System32\Logfiles\Srt\SrtTrail.txt)
After searching for several forums on my other laptop and try dozens of things, nothing helps.
Can someone on a forum that is supposed to check the test file itself.
Now I looked for the file on the laptop but, apparently, it does not exist.
What should I do now? Can I get the file online or do I have to get a new laptop with windows 8?
Additional info:
I don't have windows 8 dvd. (it was a pre installation).
I have no other pc/laptop with windows 8.
Sincerely,
Vinnie
Hello
Check with the support of ASUStek, their documentation and online to ask questions in the forums on
known problems.
ASUS - Service<-- includes="" live="">-->
http://www.service.ASUS.com/
ASUStek support
http://support.ASUS.com/
ASUStek Forums
http://VIP.ASUS.com/forum/default.aspx?SLanguage=en-us
ASUStek drivers
http://support.ASUS.com/download/download.aspx?SLanguage=en-us
=============================================
This is the Startup Repair log file.
Try to do a "Refresh your PC without affecting your files" (or modification of your personal data
settings) or even a reset (which deletes the entire).
Windows 8 includes special discount methods (keep files and settings) or a reset
(new installation remove all).
How to restore, refresh or reset your PC
http://Windows.Microsoft.com/en-us/Windows-8/restore-refresh-reset-PC
How to create a system image to refresh your PC in Windows 8
http://support.Microsoft.com/kb/2748351
How to update Windows 8
http://www.eightforums.com/tutorials/2293-refresh-Windows-8-a.html
How to reset Windows 8
http://www.eightforums.com/tutorials/2302-reset-Windows-8-a.html
If you need a repair disc:
Create a system repair disc
http://Windows.Microsoft.com/en-us/Windows7/create-a-system-repair-disc
How to create a "system repair disc" (CD/DVD) in Windows 8
http://www.eightforums.com/tutorials/2855-system-repair-disc-create-Windows-8-a.html
I hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="">-><- mark="" twain="" said="" it="">->
Tags: Windows
Similar Questions
-
I recently bought a new laptop and was getting ready to update my video card drivers, when sudenly my pc hangs for more than 10 minutes. so I forceshutdown and me when I wanted to start my laptop windows said there is a problem...
I tried to refresh / repair / recover windows but when I try to do these things my phone freezes and does nothingI need helpHello
Please keep us updated.
To run the Bootrec.exe tool, you must start Windows RE. To do this, follow these steps:
- Put the Windows 8 installation disc in the disc drive, and then start the computer.
- Press a key when you are prompted.
- Select a language, a time, a currency, a keyboard or an input method, and then clickNext.
- Click repair your computer.
- Click the operating system you want to repair, and then click Next.
- In the System Recovery Options dialog box, click command prompt.
- Type Bootrec.exe, and then press ENTER
To do this, type the following commands at the command prompt Windows RE:
- bcdedit/export C:\BCD_Backup
- c:
- Boot CD
- BCD attrib s h - r
- Ren c:\boot\bcd BCD.old
- Bootrec /RebuildBcd
Let us know if it helps.
-
Any help with this will be great
Hello
I found this link that can help you
If this does not help, you may need to recover PC to factory settings
-
AIUTO IL PC CERCA DI RIPRISTINARSI MA NON RIESCE, A ME LA COSA CHE INTERESTED DI PIU' e SALVARE TUTTI I MIEI FILE!
COME POSSO FARE? DATO CHE NON POSSO AGGIORNARE, WANT IN PRE-EMPTED BY AIUTO! THE IDEA WOULD BE QUELLA DI FORMATTARE MANTENENDO MIA I DROP MY NON HO IDEA DI COME FARE ESISTE A MODO? SCUSATE DOMANDA IMPOSTATA NO BENISSIMO, MY SOUND AGITATO!AIUTO IL PC CERCA DI RIPRISTINARSI MA NON RIESCE, A ME LA COSA CHE INTERESTED DI PIU' e SALVARE TUTTI I MIEI FILE!
COME POSSO FARE? DATO CHE NON POSSO AGGIORNARE, WANT IN PRE-EMPTED BY AIUTO! THE IDEA WOULD BE QUELLA DI FORMATTARE MANTENENDO MIA I DROP MY NON HO IDEA DI COME FARE ESISTE A MODO? SCUSATE DOMANDA IMPOSTATA NO BENISSIMO, MY SOUND AGITATO!Please re-post this in terms of the language in the menu drop-down list at the bottom of the page. This forum is for English only.
If you can't find the language you need, additional language support can be found here...
http://support.Microsoft.com/common/international.aspx -
I tried to install Windows 8 on my PC that was dual-boot WIndows 7 from 2 different hard disks and would choose between the 2 at the start. So I deleted the partition of a Windows installation and installed Windows 8. Everything seemed to work fine, I could start and choose between Windows 8 or 7 and both worked well. Then, I updated a graphics driver Win 8 and caused problems with Win starting 8 by a black screen and nothing else. There is no restore point so I decided to start by deleting the partition. I have re installed Windows 8, but now when I boot I get an error screen.
"Recovery".Your PC needs to be repairedFile: \Windows\system32\winload.exeError code: 0xc000000eYou will need to use the tools of recovery on your installation media, etc...Press Enter to try againPress F8 for startup parametersPress F9 to use another operating system.It allows me to boot from another HD after pressing F9 several times.Any advice would be appreciated.Kind regardsAnthonyI had exactly this problem with a Windows 8 machine with a hard drive only a couple of weeks might not start on Windows or Windows CD but was able to start USB recovery and follow the steps below.
Start the computer with the recovery media inserted. The computer must load the CD or USB. (You may need to change the BIOS boot sequence to start the USB drive first).Choose your language. Click next
You will now see install in the center of your screen. On the lower left side you can see fix your computer.
Choose repair.You will have several options, including:
Refresh your computer
Restore your computer
Advanced optionsChoose Advanced Options.
Launch the command prompt
Enter the following commands one at a time who hit enter after each command.
Bootrec /scanos
Bootrec /rebuildbcd
Bootrec /fixmbr
Bootrec /fixboot
Restart the computer once the last command finished -
Help! I encountered the problem of the SrtTrail.txt!
My laptop with Windows 8 Pro 64 bit does not start correctly. Whenever I start the laptop, he tells me that I have a problem and it needs to restart. He will attempt to auto-repair system. I have installed on my machine BitLocker, encrypting my C:\, so he asks the recovery key. When I enter the recovery key trying to diagnose my PC. After a minute, I said that auto repair could not fix my PC, and the file that is causing the problem is C:\Windows\System32\Logfiles\Srt\SrtTrail.txt. I tried all of the advanced options, but they do seem to work after you use the loop is executed. Someone at - it ideas on how to fix this? The laptop I'm using a SONY Vaio Duo 11 Ultrabook and I I've had for about 2/3 months.
I followed the steps to enter the command at the command prompt. When I do, I get the following message:
The drive, the path or the file name is not valid.
I entered in the following at the command prompt:
Chkdsk/f/r X:C
any other ideas?
In fact, the command is chkdsk /f /r C: no X:C
-
Windows 8 is stuck in a loop of auto repair
My windows 8 get in a loop of auto repair and he couldn't fix it. And what he said journal file d:\windows\system32\logfiles\srt\srttrail.txt
What should do?Hello Coonut,
Thank you for your reply,
I suggest you to connect to any other computer and create a floppy disk to install Windows 8. Using this disk, you can run the troubleshooting methods listed below.
See the link to create the Setup disk:
How to create the installation media for a PC refresh or reset:
http://Windows.Microsoft.com/en-us/Windows-8/create-reset-refresh-mediaHope the helps of information.
Please reply with the results, in order to help you solve the problem.
wish you a happy new year!
Thank you
-
\Windows\system32\config\system MISSING file of repair
I have a T400 who HAD an XP Pro operating system... Google chrome has frozen the system and I did a hard reboot and the computer had lost the configuration of the registry file. Microsoft recommends that the oem disc should be used, instead of a commercial version of the operating system. It's my DISLIKE for the purchase of a laptop computer with the OEM software, without a backup disk. If there is a problem, the manufacturer generally is going to drag you dry. I thought that this stratagem of Toshiba, but not of Lenovo. Hell, you can't even ask 'em to a disk if you are out of warranty. Stone wall. Why is it not possible to ask even an OEM Lenovo restore disk? Unless you have the security privileges, there is no way to even ask a repair disc: repair file \windows\system32\config\system MISSING this thread has addressed the topic of config file missing and from the looks of it nothing of this worked when even though the guy has abandoned and performed a clean installation and lost three days : http://forums.lenovo.com/t5/T61-and-prior-T-series-ThinkPad/How-to-repair-corrupt-windows-system32-c... This is not the problem of problems it's despair. I have a lot of files on that drive the need for recovery. I just want to get some tips on how to record what I have and do not go the trouble to reinstall my entire library of software and then having to reinvent my lost files. Ridiculous. Where there is an article on what works?
-
Original title: help! My PC won't start!
Hi, my computer Windows 8 really does start. On the screen, I see just the windows logo with "prepare auto repair. After, there is a message: 'automatic repair is unable to repair your PC' and ' Log: C:\windows\System32\Srt\SrtTrail.
I try with everything I can, recovery CD and USB, refresh, auto repair, I can't back up my files because I have not found any extern with 208 GB storage... So I can't really reset my PC without losing my files.
What can I do to start my PC, without losing my files.
PLEASE, I BEG YOU! Help me!!! PLEASE, I BEG YOU!
Hello
Thanks for posting your query on the Microsoft Community.
According to the description, I understand that you are unable to start your computer.
This could occur due to system conflicts.
Try the steps.
If the auto repair is unable to repair your PC, select "Advanced options" and then "Troubleshooting."
- Select 'Advanced options', then 'command prompt'.
- If you are prompted, enter the password for the user name.
- At the command prompt, type the following commands, and press ENTER.
Bootrec /fixMBR
Bootrec /Fixboot
Bootrec /rebuildBCDRestart the computer and check the issue.
Hope this information helps. Please let us know if you need any other help with Windows in the future. We will be happy to help you.
-
I get an error code whenever I start my computer. I have loaded several packs of registry repair software but cannot get rid of the message. The message bed error loading c:\windows\system32\pofusido.dll the specified module is not found
Hello
I googled this file pofusido.dll and it could be caused by a virus.
I would suggest that you disable the restore mode as viruses use it to reinstall set apart them.
Download and install the free http://www.malwarebytes.org/
Restart the computer and keep pressing F8 to get into safe mode with network connection.
Once you have updated Malwarebytes run and see if it can remove the virus.
So delete all cookies in your internet Explorer.
Please keep in mind that my answer is based on the information in your message. More the better I can answer, Slan go foill, Paul
-
How to repair this error C:\Windows\System32\mscoree.dll__
How to repair this error C:\Windows\System32\mscoree.dll
Hello
Follow these steps to remove corruption and missing/damaged file system repair or replacement.
Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN
sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.htmlIf necessary:
Mscoree.dll could not be found error resolution
http://pcsupport.about.com/od/findbyerrormessage/a/mscoree-DLL-not-found-missing-error.htmI hope this helps.
Rob - bicycle - Mark Twain said it is good. -
file missing or corrupt windows\system32\config\system
HELP - by on the title I did: -.
The full, first part, follow these steps:
- Insert the diskette of starting Windows XP in the floppy drive, or insert the Windows XP CD into the CD-ROM drive and restart the computer.
Click to select all of the options required to start the computer from the CD-ROM drive if you are prompted to do so. - When the "Welcome" screen appears, press R to start the Recovery Console.
- If you have a dual-boot or multiboot, select the installation that you want to access from the Recovery Console.
- When you are prompted to do so, type the administrator password. If the administrator password is blank, just press ENTER.
- At the Recovery Console prompt, type the following lines, pressing ENTER after you type each line:MD tmp
copy c:\windows\system32\config\system c:\windows\tmp\system.bak
copy c:\windows\system32\config\software c:\windows\tmp\software.bak
Copy c:\windows\system32\config\sam c:\windows\tmp\sam.bak
copy c:\windows\system32\config\security c:\windows\tmp\security.bak
copy c:\windows\system32\config\default c:\windows\tmp\default.bakdelete c:\windows\system32\config\system
delete c:\windows\system32\config\software
Delete c:\windows\system32\config\sam
delete c:\windows\system32\config\security
Delete c:\windows\system32\config\defaultCopy c:\windows\repair\system c:\windows\system32\config\system
copy c:\windows\repair\software c:\windows\system32\config\software
copy c:\windows\repair\sam c:\windows\system32\config\sam
Copy c:\windows\repair\security c:\windows\system32\config\security
Copy c:\windows\repair\default c:\windows\system32\config\default - Type exit to quit the Recovery Console. Your computer will restart.
Note This procedure assumes that Windows XP is installed in the C:\Windows folder. Make sure that replace C:\Windows with the appropriate dossier_Windows if it is a different place.
If you have access to another computer, to save time, you can copy the text in step 5, and then create a text file called "Regcopy1.txt" (for example). To use this file, run the following command when you start in Recovery Console:
batch regcopy1.txtWith the command batch to the Recovery Console, you can process all the commands in a text file in the order. When you use thebatch command, you do not have to manually type as many commands.
Second part
To perform the procedure described in this section, you must be logged in as administrator or an administrative user (a user who has an account in the Administrators group). If you use Windows XP Home Edition, you can connect as an administrative user. If you sign in as an administrator, you must first start Windows XP Home Edition in safe mode. To start the computer in Windows XP Home Edition in safe mode, follow these steps.
Note Print these instructions before continuing. You cannot view these instructions after you restart the computer in Mode safe. If you use the NTFS file system, also print the instructions from article KB309531 of the Knowledge Base. Step 7 contains a reference to the article.
- Click Start , click shut down (or click turn off computer ), click restart , and then click OK (or click restart ).
- Press the F8 key.
On a computer that is configured to start to multiple operating systems, you can press F8 when you see the boot menu.
- Use the arrow keys to select the appropriate safe mode option and press ENTER.
- If you have a dual-boot or multiboot system, use the arrow keys to select the installation that you want to access, and then press ENTER.
In part two, you copy the registry of their location saved files by using the system restore. This folder is not available in the Recovery Console, and is usually not visible on the typical use. Before you begin this procedure, you must change several settings to make the folder visible:
- Start Windows Explorer.
- On the Tools menu, click folder options .
- Click the view tab.
- Under hidden files and folders , select Show hidden folders and files , and then click to clear theHide protected (recommended) operating system files check box.
- When appears in the dialog box confirming that you want to display these files, click Yes .
- Double-click the drive where you installed Windows XP to display the list of folders. If it is important to click on the correct drive.
- Open the System Volume Information folder. This folder is not available and is dimmed because it is defined as a file hidden doubling.
Note This folder contains one or more _restore {GUID} folders such as "_restore {87BD3667-3246-476B-923F-F86E30B3E7F8}.
Note You may receive the following error message:
C:\System Volume Information is not accessible. Access is denied.If you receive this message, see the following article in the Microsoft Knowledge Base for access to this folder and continue with the procedure:
309531 (http://support.microsoft.com/kb/309531/) how to access the System Volume Information folder - Open a folder that was created not at the present time. You may need to clickDetails on the view menu to see when these folders were created. There may be one or more folders starting with "RPx under this folder. Here are the restore points.
- Open one of these folders to find a subfolder of the snapshot. The following path is an example of a folder path to the snapshot folder:C:\System Volume \RP1\Snapshot Information\_restore {D86480E3-73EF-47BC-A0EB-A81BE6EE3ED8}
- Starting from the Snapshot folder, copy the following files to the C:\Windows\Tmp folder:
- _REGISTRY_USER_. DEFAULT
- _REGISTRY_MACHINE_SECURITY
- _REGISTRY_MACHINE_SOFTWARE
- _REGISTRY_MACHINE_SYSTEM
- _REGISTRY_MACHINE_SAM
- Rename the files in the C:\Windows\Tmp folder as follows:
- Rename _REGISTRY_USER_. DEFAULT DEFAULT
- Rename _REGISTRY_MACHINE_SECURITY to SECURITY
- Rename _REGISTRY_MACHINE_SOFTWARE to SOFTWARE
- Rename _REGISTRY_MACHINE_SYSTEM to SYSTEM
- Rename _REGISTRY_MACHINE_SAM to SAM
These files are the system restore registry files. Because you used the registry file that the Setup program created, this registry does not know that these restore points exist and are available. A new folder is created with a new GUID under System Volume Information and a restore point is created that includes a copy of the registry files that were copied during the first part. Therefore, it is important not to use the most recent folder, especially if the time stamp on the folder is the same at the moment.
The current configuration of the system is not aware of the previous restore points. You must have a previous copy of the registry to a previous restore point to make previous restore available again points.
The registry files that were copied to the Tmp folder in the C:\Windows folder are moved to ensure the files are available in the Recovery Console. You use these files to replace the registry files currently in the C:\Windows\System32\Config folder. By default, the Recovery Console has limited access to records and cannot copy the files in the File System Volume.
Note The procedure described in this section assume you are using your computer with the FAT32 file system. For more information on how to access the folder of information system with the NTFS file system Volume, click on the number below to view the article in the Microsoft Knowledge Base:
309531 (http://support.microsoft.com/kb/309531/) how to access the System Volume Information folderThird part
In part three, you delete the existing registry files, and then copy the system restore registry files to the C:\Windows\System32\Config folder:
- Start the Recovery Console.
- At the command prompt, type the following lines, pressing ENTER after you type each line:del c:\windows\system32\config\sam
del c:\windows\system32\config\security
del c:\windows\system32\config\software
del c:\windows\system32\config\default
del c:\windows\system32\config\system
copy c:\windows\tmp\software c:\windows\system32\config\software
copy c:\windows\tmp\system c:\windows\system32\config\system
copy c:\windows\tmp\sam c:\windows\system32\config\sam
Copy c:\windows\tmp\security c:\windows\system32\config\security
Copy c:\windows\tmp\default c:\windows\system32\config\default
Note Some of these command lines may be wrapped for readability.
- Insert the diskette of starting Windows XP in the floppy drive, or insert the Windows XP CD into the CD-ROM drive and restart the computer.
- Type exit to quit the Recovery Console. Restart the computer.
- Click Start and then click all programs .
- Click on Accessories , then System Tools .
- Click System Restore , and then click restore to a previous RestorePoint .
-
I have a desktop computer Acer, about 4 years old, running Windows XP SP2. When I started my computer, it does not boot in any mode, and I get this error message:
Windows has not start because the following file is missing or damaged:
\windows\system32\config\system
You can attempt to repair this file by starting windows setup using the original setup cd-rom
Select 'r' in the first screen to start repair.I don't have a Setup disk and wonder if it would help in all cases. Any ideas?
You can not download configuration online info. I have a second XP computer which is supposed to have access to the configuration file in the Add/Remove Programs section, but I don't have any tab to create a disk for installation here. Do you know where he's hiding on this computer? If not, can I get a copy of this MS installation disc?
Thank youThank you
Manual steps to recover a corrupted registry that prevents the start of the procedure that this article describes to Windows XP using System Restore and Recovery Console. This article lists also all required specific steps to ensure that the process is fully completed. When you have completed this procedure, the system returns to a state very close to the State until the problem occurred. If you have ever run NTBackup and completed a system state backup, you don't have to follow the procedures in parts two and three. You can go to part IV. First part in the first part, you start the Recovery Console, create a temporary folder, back up the existing registry files to a new location, delete the registry from their existing location files and then copy the registry files in the repair folder to the System32\Config folder. When you have completed this procedure, a registry is created that you can use to start Windows XP. This registry was created and saved during the initial setup of Windows XP. Therefore, any changes and settings that took place after Setup has finished are lost.
The full, first part, follow these steps:
- Insert the diskette of starting Windows XP in the floppy drive, or insert the Windows XP CD into the CD-ROM drive and restart the computer.
Click to select all of the options required to start the computer from the CD-ROM drive if you are prompted to do so. - When the "Welcome" screen appears, press R to start the Recovery Console.
- If you have a dual-boot or multiboot, select the installation that you want to access from the Recovery Console.
- When you are prompted to do so, type the administrator password. If the administrator password is blank, just press ENTER.
- At the Recovery Console prompt, type the following lines, pressing ENTER after you type each line:MD tmp
copy c:\windows\system32\config\system c:\windows\tmp\system.bak
copy c:\windows\system32\config\software c:\windows\tmp\software.bak
Copy c:\windows\system32\config\sam c:\windows\tmp\sam.bak
copy c:\windows\system32\config\security c:\windows\tmp\security.bak
copy c:\windows\system32\config\default c:\windows\tmp\default.bakdelete c:\windows\system32\config\system
delete c:\windows\system32\config\software
Delete c:\windows\system32\config\sam
delete c:\windows\system32\config\security
Delete c:\windows\system32\config\defaultCopy c:\windows\repair\system c:\windows\system32\config\system
copy c:\windows\repair\software c:\windows\system32\config\software
copy c:\windows\repair\sam c:\windows\system32\config\sam
Copy c:\windows\repair\security c:\windows\system32\config\security
Copy c:\windows\repair\default c:\windows\system32\config\default - Type exit to quit the Recovery Console. Your computer will restart.
Note This procedure assumes that Windows XP is installed in the C:\Windows folder. Make sure that replace C:\Windows with the appropriate dossier_Windows if it is a different place.
If you have access to another computer, to save time, you can copy the text in step 5, and then create a text file called "Regcopy1.txt" (for example). To use this file, run the following command when you start in Recovery Console:
batch regcopy1.txtWith the command batch to the Recovery Console, you can process all the commands in a text file in the order. When you use the batch command, you do not have to manually type as many commands. Second part to perform the procedure described in this section, you must be logged on as an administrator or an administrative user (a user who has an account in the Administrators group). If you use Windows XP Home Edition, you can connect as an administrative user. If you sign in as an administrator, you must first start Windows XP Home Edition in safe mode. To start the computer in Windows XP Home Edition in safe mode, follow these steps.
Note Print these instructions before continuing. You cannot view these instructions after you restart the computer in Mode safe. If you use the NTFS file system, also print the instructions from article KB309531 of the Knowledge Base. Step 7 contains a reference to the article.
- Click Start , click shut down (or click turn off computer ), click restart , and then click OK (or click restart ).
- Press the F8 key.
On a computer that is configured to start to multiple operating systems, you can press F8 when you see the boot menu.
- Use the arrow keys to select the appropriate safe mode option and press ENTER.
- If you have a dual-boot or multiboot system, use the arrow keys to select the installation that you want to access, and then press ENTER.
In part two, you copy the registry of their location saved files by using the system restore. This folder is not available in the Recovery Console, and is usually not visible on the typical use. Before you begin this procedure, you must change several settings to make the folder visible:
- Start Windows Explorer.
- On the Tools menu, click folder options .
- Click the view tab.
- Under hidden files and folders , select Show hidden folders and files , and then click to clear the Hide protected (recommended) operating system files check box.
- When appears in the dialog box confirming that you want to display these files, click Yes .
- Double-click the drive where you installed Windows XP to display the list of folders. If it is important to click on the correct drive.
- Open the System Volume Information folder. This folder is not available and is dimmed because it is defined as a file hidden doubling.
Note This folder contains one or more _restore {GUID} folders such as "_restore {87BD3667-3246-476B-923F-F86E30B3E7F8}.
Note You may receive the following error message:
C:\System Volume Information is not accessible. Access is denied.If you receive this message, see the following article in the Microsoft Knowledge Base for access to this folder and continue with the procedure:
309531 (http://support.microsoft.com/kb/309531/) how to access the System Volume Information folder - Insert the diskette of starting Windows XP in the floppy drive, or insert the Windows XP CD into the CD-ROM drive and restart the computer.
- Open a folder that was created not at the present time. You may need to click Details on the view menu to see when these folders were created. There may be one or more folders starting with "RPx under this folder. Here are the restore points.
- Open one of these folders to find a subfolder of the snapshot. The following path is an example of a folder path to the snapshot folder:C:\System Volume \RP1\Snapshot Information\_restore {D86480E3-73EF-47BC-A0EB-A81BE6EE3ED8}
- Starting from the Snapshot folder, copy the following files to the C:\Windows\Tmp folder:
- _REGISTRY_USER_. DEFAULT
- _REGISTRY_MACHINE_SECURITY
- _REGISTRY_MACHINE_SOFTWARE
- _REGISTRY_MACHINE_SYSTEM
- _REGISTRY_MACHINE_SAM
- Rename the files in the C:\Windows\Tmp folder as follows:
- Rename _REGISTRY_USER_. DEFAULT DEFAULT
- Rename _REGISTRY_MACHINE_SECURITY to SECURITY
- Rename _REGISTRY_MACHINE_SOFTWARE to SOFTWARE
- Rename _REGISTRY_MACHINE_SYSTEM to SYSTEM
- Rename _REGISTRY_MACHINE_SAM to SAM
- Start the Recovery Console.
- At the command prompt, type the following lines, pressing ENTER after you type each line:del c:\windows\system32\config\sam
del c:\windows\system32\config\security
del c:\windows\system32\config\software
del c:\windows\system32\config\default
del c:\windows\system32\config\system
copy c:\windows\tmp\software c:\windows\system32\config\software
copy c:\windows\tmp\system c:\windows\system32\config\system
copy c:\windows\tmp\sam c:\windows\system32\config\sam
Copy c:\windows\tmp\security c:\windows\system32\config\security
Copy c:\windows\tmp\default c:\windows\system32\config\default
- Type exit to quit the Recovery Console. Restart the computer.
- Click Start and then click all programs .
- Click on Accessories , then System Tools .
- Click System Restore , and then click restore to a previous RestorePoint .
-
Satellite A100-207 - \windows\system32\config\system is corrupt
Hello
Can someone help me with the following problem. With regard to a Toshiba Satellite A100-207 with windows XP media edition
When starting the laptop hangs with error * \windows\system32\config\system is corrupt *.
This article is the closest to the problem http://support.microsoft.com/kb/307545. but the warning in the article on the point is not to use with circumspect OEM on more facilities of he made me.
I have lost the disc of recovery (recently).
But were able to boot the laptop from USB using a cutter (lite) version of windows.The scene in the article copy c:\windows\repair\system c:\windows\system32\config\system fails because the file does not exist (the other files do however).
In this folder there is a system.bak, this would solve the problems like the laptop boots windows logo screen then after 5 minutes restarts and just go around and around a certain extent.
There is also a file system.sav in the folder windows\system32\config using this all goes someway to to solve the problem, the laptop restarts and resumes product set-up with off course fails has so I don't have the recovery disk.
I would be grateful if someone could help with the problem
Regards Garry
> but the warning in the article on the point is not to use with circumspect OEM on more facilities of he made me.
You can ignore this warning, you have no other choice than to try to fix this system following the article in the Microsoft Knowledge base.
But to be honest, I doubt that the system would run smoothly after this work around.
I would recommend the new installation of the OS.
If you don t have a Toshiba Recovery disk, you can use a Microsoft Disk to reinstall the system. Essential drivers are available Toshiba driver Web site. -
I can't open windows live mail and other programs that also many installers will not work for this reason.
I get the following error:
wlmail.exe - incorrect Image
C:\Windows\System32\wship6.dll is not designed to run on
Windows or it contains an error. Try to install the program using the
the original installation media or contact your system administrator or
the Publisher of the software to supportI had to click OK 4 or 5 times to make it go away
Many installers will not work because of this.
System information:
OS version: Microsoft Windows 7 Home Premium, Service Pack 1, 64-bit
Processor: AMD A6 - 3400 M APU with graphics HD Radeon (TM), AMD64 family 18 model 1 Stepping 0
Number of processors: 4
RAM: Mb 5610
Graphics card: AMD Radeon (TM) HD 6520 G, 512 MB
Hard disks: C: Total - Mo 595354, Free - Mo 401604; Total D: - 14820 MB, free - 1647 MB; F: total - 99 MB, free - 89 MB; G: total - Mo 953867, Free - 877240 MB;
Motherboard: Hewlett-Packard, 358B
Antivirus: Norton Internet Security, updated and activatedHere's what I did to remedy:
I had to replace the \wship6.dll c:\windows\sysWOW64 file not the file c:\windows\system32\wship6.dll
I had to start Windows Recovery Environment, load the command prompt and replace the file c:\windows\sysWOW64\wship6.dll to a system of work w7 (I used an iso oem and 7zip)
( 1 copy the file in a place should be on my boot drive (c :) in my case))
2 . restart your computer , press and hold F8 as your computer restarts. You need to press F8 before the Windows logo appears. If the Windows logo appears, you will need to start over; to do this, hold the Windows logon prompt appears, and then stop and restart your computer.
3 . Select repair your computer and press enter.
4 . Select the option for command line
type 5 bcdedit | find "osdevice" (note that there is a space after bcdedit and | and also find) that will tell you what drive letter to use to access your startup drive (d: in my case)
type 6 the drive letter followed by a: (d: in my case) and press enter , the guest must pass to < DriveLetter >: (in my case d:)
type 7 copy < your place should be > wship6.dll windows\syswow64\wship.dll (replace < your place should be > with the full path to where you place the file) (note the space between the .dll and windows)
If this does not work, you may need to replace syswow64 system32 in all the above instructions
Note This procedure assumes that Windows XP is installed in the C:\Windows folder. Make sure that replace C:\Windows with the appropriate dossier_Windows if it is a different place.
If you have access to another computer, to save time, you can copy the text in step 2, and then create a text file named "Regcopy2.txt" (for example). To use this file, run the following command when you start in Recovery Console:
Fourth part
and now when I go to the fourth part and try to connect, it says I need to activate windows to open a session. If I click on Yes, the computer crashes just in my background image, if I click on no, this Chuck me back to the log in page... What is wrong with this blooming thing
Please HELP - it took three days of messing around and actually the Ive got nowhere!
Do, or do not. There is no test.
I need YOUR voice and the points for helpful answers and propose responses. I'm saving for a pony!
These files are the system restore registry files. Because you used the registry file that the Setup program created, this registry does not know that these restore points exist and are available. A new folder is created with a new GUID under System Volume Information and a restore point is created that includes a copy of the registry files that were copied during the first part. Therefore, it is important not to use the most recent folder, especially if the time stamp on the folder is the same at the moment.
The current configuration of the system is not aware of the previous restore points. You must have a previous copy of the registry to a previous restore point to make previous restore available again points.
The registry files that were copied to the Tmp folder in the C:\Windows folder are moved to ensure the files are available in the Recovery Console. You use these files to replace the registry files currently in the C:\Windows\System32\Config folder. By default, the Recovery Console has limited access to records and cannot copy the files in the File System Volume.
Note The procedure described in this section assume you are using your computer with the FAT32 file system. For more information on how to access the folder of information system with the NTFS file system Volume, click on the number below to view the article in the Microsoft Knowledge Base:
Part three in the third part, you delete the existing registry files, and then copy the system restore registry files to the C:\Windows\System32\Config folder:
Note Some of these command lines may be wrapped for readability.
Note This procedure assumes that Windows XP is installed in the C:\Windows folder. Make sure that replace C:\Windows with the appropriate dossier_Windows if it is a different place.
If you have access to another computer, to save time, you can copy the text in step 2, and then create a text file named "Regcopy2.txt" (for example). To use this file, run the following command when you start in Recovery Console:
Fourth part
Good luck! Please rate me upward if you find my post helpful. Thank you!
Maybe you are looking for
-
Hello Are you logged in as administrator - you run the patch by clicking right - RUN AS ADMIN (if possible) tooland it is also possible that you don't need the patch tool. Some of these updates may not be necessary either - you can control panel - Wi
-
Battery wakes up from sleep mode
I have a user that the laptop wakes mode standby when the laptop is closed. We have changed the battery, checked the settings for the mode "Eve" (wake on LAN, etc.) and he still wakes upward while the lid is closed. In addition, the laptop gets reall
-
My BB Bold 9000 doesn't send text messages. I had no problem sending texts to the end of last week. Now in my Outbox SMS all my text messages are displayed with a red box with a small tail to the 12:00 position and another small line to the positio
-
PN-online, publication in InDesign error
Hi my problem is that I'm loading a file and keep getting and error #40 ID bac66480-5d36-11e6-8499-ebe4604817a1Also what is memory wise to the amount of files limit, you can publish and if there is a limit can you get more?I hope you can helpThank yo