Replace the drive failed in md1200

Similar Questions

• Error No. Boot Disk was detected or the drive failed - h8-1020 Desktop

  1 hp pavilion HPE h8-1020

  2. windows 7 64 bit

  3. Realtek PCIe GBE Family Controller series v2.38 24/12/10

  Error: No boot disk was detected or the drive failed.

  4. no changes to the system.

  After I restarted my computer about 7 times it finally started, so for me to be able to write this message.  However, this problem occurred several times over the last week or two. I get a blue screen, then the computer goes into a splash screen and I get the above error.  Of course, I'm 2 months past my warranty period, so I'm here, GROUND.

  Is my hard drive on its way? Is there a possible difficulty for this seizure completely breaks down?  Information to help save my machine would be great and much appreciated.  Thank you!

  P.S. I ran a diagnostic and all past test except the bootable disc.  But for some reason when I restart a little more time it get passed my system and begins running.

  Note: I created recovery discs and I backed up all my files.

  Hello:

  In my view, there is nothing you can do to repair the drive except to replace it.

  You can run the checkdisk utility and check both boxes.

  Please see the link below for more information.

  http://www.w7forums.com/use-chkdsk-check-disk-t448.html

  Please understand that this will only delay the inevitable at best.

  Paul

• HP Pavilion TouchSmart 23-f202: no boot disk was detected or the drive failed

  On startup, I get the message "no boot disk was detected or the drive failed.

  I bought a new H/D, installed and at startup I get the same message that I got on the old H/D.

  As there was no disc provided with the computer when I bought what I'm doing, had to do to get this sucker to the top and work?

  Hi @Jimmy56,

  Welcome to the Forums of HP Support! I understand that you had a type "no boot drive has been detected" error at startup to the top, and you have replaced the hard drive and have the same problem. I'm happy to help you with this.

  If replace you the original hard disk, you can use the following to test the hard drive. It is possible, there was a connectivity issue and just re-allocation of places the hard drive could make a difference. Computers HP - display of error HDD before starting the computer

  The most recent hard disk you put in, if not there was no operating system installed, you'll get the same type of message. You could make the same diagnosis of HDD from the link above, just to make sure that the disc is good.

  Please let me know the results, but so just install the original in the system hard disk works, and it starts correctly, so please mark this message as a solution. Bravo would be appreciated as well.

• My Omni 27-1057c Gets a "ERROR: not detected no boot disk or the drive failed.

  The computer will start up to run for a while appear them error: no boot disk was detected or the drive failed.

  Hello

  Follow the link below:

  http://support.HP.com/us-en/document/c00439024

  run a test of hard drive failure is the problem HARD drive... u can save the data n replace it. If it passes the back up of the data and perform a restore of the OS and reinstall the OS

• replacing a drive failing on vsphere host

  Dear all,

  I need to clarify something here. In the environment for both blade servers configured with Raid 1, a balde running Esxi 4.0, 208167 and other is Esxi running 5.0, 914586. Recently, one of the player on each blade is projecting an orange light.

  I need to know the defective disk can be replaced online at vpshere host? Something special to be taken in charge power off.

  Kind regards

  It depends on whether the drives are hot pluggable. Where they are - which should be the case for the company's servers - it is actually better to replace the drives online. In this way the controller knows which disk has been replaced and that one is healthy, that must be synchronized to the new. Check again with the documentation of the service provider to a controller. Another tip, if you replace a disk online, make sure that you wait at least a minute or two after removing the failed drive and before inserting the new disc, to allow the controller to properly recognize the replacement!

  André

• PAGE_FAULT_IN_NONPAGED_AREA___Msg DISK_0? Block 8: can? t read, replace the drive or remove the writing (Dell Dignostic softare scan) _ Protection

  I had purchase Dell inpiron 910 mini two years before now out of warranty. I got error on blue screen and then I restart the machine, I got the mode without failure when starting in safe mode, it stops and a disk read error occurred press Ctr + alt + del to restart I could even not to format the machine. could not start for winodow cd. Same blue screen message when starting from the cd, the message is as below
  A problem has been detected and windows has shut down to prevent damage to your computer.

  The problem seems to be caused by the following file: partmgr.sys

  PAGE_FAULT_IN_NONPAGED_AREA

  If this is the first time you've seen this stop error screen,

  Restart your computer. If this screen appears again. follow these steps:

  check to make sure any new hardware or software is installed correctly.

  If it is a new installation. Ask the manufacturer of your hardware or software for any windows update you might need.

  If the problem persists. disable or remove any newly installed hardware or software. Disable BIOS memory option such as caching or shading if you need to use safe mode to remove or disable components, restart your computer, press F8 to select advanced startup options. then select Safe mode.

  Technical information:

  STOP: 0 X 00000050 (0XF7895726, 0X00000000, 0X00000000)

  Partmgr.sys - address F7895726 base at F7893000, DateStamp 00000000

  I ran the Dell cd dignostic is to show the following error message:
  Error Code 0F00:1344

  MSG DISK_0? Block 8: can? t read, replace the drive or remove the write protect

  The given error code and message can use Dell Technical Support to help diagnose the problem.

  Hello

  ·        Since when are you facing this problem?

  ·        Remember to make changes to the system?

  I suggest to unplug external devices such as printer, scanner, etc. that are plugged into the system, and then restart the system and check if the problem persists.

  Error code 0F00:1344 you listed are hard drive error codes. Usually, this means that the hard drive needs to be replaced. I suggest you to contact Dell support for assistance. Once the hard disk is fixed, you can try the methods mentioned below.

  Click on the link below, contact Dell technical support.

  http://en.community.Dell.com/support-forums/disk-drives/default.aspx

  Method 1:

  I suggest you to do a check disk from the recovery console and check if the problem is resolved. Follow the steps mentioned below.

  a. start into the recovery console using the XP CD. Follow the steps mentioned in the article below.

  Description of the Windows XP Recovery Console for advanced users

  http://support.Microsoft.com/kb/314058

  b. perform a disk check.

  How to perform disk error checking in Windows XP

  http://support.Microsoft.com/kb/315265

  Method 2:

  I suggest you to start with the XP CD and then do a system restore. Follow the steps mentioned in the article below.

  How do I recover from a corrupted registry that prevents Windows XP startup

  http://support.Microsoft.com/kb/307545

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit ourMicrosoft answers feedback Forum and let us know what you think.

• Error message = the driver failed charging USB\VID_0A5C & PID_5802 & MI_01\7 \Driver\WUDFRd & 95fd152 & 0 & 0001.

  WARNING on 13/10/2011 11:06:08 Kernel - PnP 219 (212)

  Log name: System
  Source: Microsoft-Windows-Kernel-PnP
  Date: 13/10/2011 11:06:08
  Event ID: 219
  Task category: (212)
  Level: WARNING
  Keywords:
  User: SYSTEM
  Computer: Buzz_Murdock-PC
  Description:
  The driver failed to load the device USB\VID_0A5C & PID_5802 & MI_01\7 \Driver\WUDFRd & 95fd152 & 0 & 0001.
  The event XML:
  http://schemas.Microsoft.com/win/2004/08/events/event">
   
     
      219
      0
      3
      212
      0
      0 x 8000000000000000
     
      145356
     
     
      System
      Buzz_Murdock-PC
     
   
   
      44
      USB\VID_0A5C & PID_5802 & MI_01\7 & 95fd152 & 0 & 0001
      3221226341
      14
      \Driver\WUDFRd
      0
   
  

  I know it's fine... I had the same problem and I stopped the error... I went into services.msc and last 'Manual' under 'Windows Driver Foundation - User - Mode Driver Framework' to 'automatic '.
  This stopped the error in Event Viewer.  It worked for me!

  According to microsoft, the error is benign... It's just a matter of latency.

• Have installed Photoshop CS4. Replaced the drive hard and now I get error code 150:30. What should I do to get it working again

  Have installed Photoshop CS4. Replaced the drive hard and now I get error code 150:30. What should I do to get it working again

  Migration of CS4 breaks the license. That's what 150:30 means. Assuming you are using a Mac.

  You can use the Terminal method to repair the license... but I stress that carefully read you and understand the instructions here before you run it. beginning

  # 11. https://forums.Adobe.com/thread/1714695

  If this isn't what you want to do, you have to reinstall.

  Gene

• installed the file ISO of ESXI 5.5.0 of trialware on a PC at home that has a memory of 8meg, installed correctly, then on reboot I get 'no boot disk was detected or the drive failed', I'm boot from the hard disk, any ideas?

  installed the file ISO of ESXI 5.5.0 of trialware on a PC at home that has a memory of 8meg, installed correctly, then on reboot I get 'no boot disk was detected or the drive failed', I'm boot from the hard disk, any ideas?

  Welcome to the community,

  Please take a look at for example http://wp.secretnest.info/?p=697 to know if this is the problem you are facing.

  André

• Replacing the drive system of IQ770

  My IQ770 system disk is defective and must be replaced.

  Anyone know where I can find details on replacing this drive?

  Easy,.

  Take a SATA on your preferred provider. 30 GB - 10 000 tb

  Example of 500 GB = £30

  Better yet to catch one in a basket, then you get a caddy for an extra 10 or 15 dollars.

  But 3.5 "disk right!  You can use a notebook drive, they work too, but perhaps not as well.

  Find an imaging tool to perform disk to disk cloning (ghosting).

  Remove the current disc, connect to a shopping cart.

  connect new drive to a shopping cart

  Connect to a working machine and clone.

  I don't think that you can clone an active (System) drive, that's why I said remove.

  But there may be other methods around to clone the disks these days.

  Maybe start on OS linux on CD, with a disk in the machine and the other in the caddy.

  There are always several ways to peel a Banana.

  In any case, cloning the drive will ensure that you keep your intact recovery partition.

  Once cloned infact it will be just plug and

  the machine will be exactly how it was, but a new drive.

  Ahhhh... the disk location... ??

  Raise the screen,

  You will find the release in the central section, the top of the front façade.

  (above the crack CD and scale, below the joint)

  This will push down (not in) and the rear is going to jump off.

  Loosen the two lower screws of caddy, remove the two more top of the page.

  To replace the back cover just hold against the contact surface

  and press the release button again, do not try to break all just come back on!

  If you just bend the metal tabs to the original shape once you fail.

  The rest should be simple veil.

  Hope that helps.

  HV.

• (Redirected) Alienware Aurora R4 - replacement hard drive failed by disk image

  I went to the Dell website and ran the diagnostics for my R4 Aurora. He said that the hard drive had no 2 tests. So, Dell quickly sending a hard drive 2 TB of replacement. I received it today. The bag of the hard drive has a sticker that says "image". I guess that means that a new installation of my Windows 7 Ultimate factory has been installed on the hard disk. I did not receive any instructions, except to say that I need to replace the failed hard drive and return it within 30 days. OK, I can do the physical dominance, but there are a lot of questions, I feel unanswered.

  Where are the instructions step by step to do this?

  Should I get the ID product, s/serials for Windows 7 and office products that I have on the old drive?

  Someone please point me in the right direction. My warranty includes no cat, and Facebook and Twitter are not my best subjects when it comes to getting help.

  Any help will be greatly appreciated. The moderators of Dell, plese chime and let me know as well.

  Thank you

  johnssm

  Best of this post in the Alienware owners Club Forum, here:

  http://en.community.Dell.com/Owners-Club/Alienware/default.aspx

  Bev.

• Need to replace the drive but not allowing OpenManage not not fault reader must be set to 'offline '.

  Hello

  We hope a quick and easy solution to what I'm procrastinating at the moment.

  Have a server Poweredge 1800 (PERC 4/SC, RAID5) and got a failure on one of the SCSI drives. It's hot and we got the replacement.

  However, OpenManage is not let me put the failed drive to 'offline' so that I can share. I'll choose the option offline in the menu drop down and when running it just empty screens (see photo). Is this a symptom of something not quite right? No problem with other options (blink/unblink).

  If not can I just start in the PERC menu, set the active player in offline mode, swap, set the new drive to rebuild from there?

  Seems to be a split view when I look at other similar questions on other threads in forum, for example, some say that you should just pull the drive and Exchange even without putting off line first.

  Thank you

  Alex

  

  Alex,

  It is possible that you are using an older version of the OMSA or that the controller is out of date.

  With the drive is not going offline. What you can do is to the server once it is off, then remove the disc. Powered with nothing in this niche, the table should show that degraded. Insert the replacement drive and it should start to rebuild.

  Let me know how it goes.

• Replacing the drive HARD on Portege R700

  Hello

  I just ordered a R700 and hope to upgrade the HARD drive of 320 GB for one SSD OCZ Vertex 2.
  Is it easy to replace the hard drive in the R700? Should I remove the keyboard is a Panel on the back?
  What size hard disk will - 2.5 "or 1.8"?
  A SSD will be simply connect using existing connections, or something else there?

  See you soon.

  According to the specifications of the laptop Portege R700 has 2.5 HARD drive is HDD with SATA interface, so I think that you should order 2.5 SSD with standard SATA connectors.

  HARD drive is placed on the bottom side near the cooling vent and it is fixed with a screw only.

  Remove the screws and HARD drive. You will see how the HARD disc is placed and how it must be removed.
  It's very simple and you can do it alone.

• Replacing the drive HARD Satellite Pro 4280

  I have a SP 4280 and the original hard drive on it does not have earlier. I bought a Hitachi Travelstar 5K 100 40 GB replacement, but I can't seem to make it work. FDisk recognizes the disc as a 40 GB drive and seems to format the drive. However, attempts to write anything to generate results in an error message "invalid media".

  Installation using XP Pro format the drive gives me an error message in the sense of "Windows cannot format the drive.

  I have attached the drive to my PC via a cable of adapter 2.5 "and it seems to work fine. I also use the latest version of the BIOS on my laptop. It is not the settings of 'cable' rider select and 0/1 on the drive.

  Someone knows what the problem is, or that I couldn't do or have suggestions to raise my drive and running?

  Cheers in advance

  Hello

  Your device was shipped with a 6 GB HARD drive.
  In my opinion, the BIOS has a few problems with the recognition of the HARD drive because of the large size of HARD drive. Unfortunately, I put t see any possibility to solve the problem.

• Replacing the drive HARD on Satellite C850

  I found this Toshiba on Youtube video that shows how to replace the hard drive on the C850.
  http://www.YouTube.com/watch?v=0550V-181d0

  It helped me a lot, because there is NO entry in the user manual on how to replace it and where the hard drive can be placed.

  They show you where is the memory, but not where is the hard drive. WTF? so, this video tells you it's in the same slot for memory.

  Hello

  Yes, I also noticed that not all information can be found in single user manuals.
  However, there are many other sources to find essential details.

  Toshiba Europe youtube channel seems to offer a lot of useful videos to replace the HARD drive, memory or a drive CD/DVD in the different laptop models.
  http://www.YouTube.com/user/toshibaeuropesupport