Replacing the drive system of IQ770

Similar Questions

• PAGE_FAULT_IN_NONPAGED_AREA___Msg DISK_0? Block 8: can? t read, replace the drive or remove the writing (Dell Dignostic softare scan) _ Protection

  I had purchase Dell inpiron 910 mini two years before now out of warranty. I got error on blue screen and then I restart the machine, I got the mode without failure when starting in safe mode, it stops and a disk read error occurred press Ctr + alt + del to restart I could even not to format the machine. could not start for winodow cd. Same blue screen message when starting from the cd, the message is as below
  A problem has been detected and windows has shut down to prevent damage to your computer.

  The problem seems to be caused by the following file: partmgr.sys

  PAGE_FAULT_IN_NONPAGED_AREA

  If this is the first time you've seen this stop error screen,

  Restart your computer. If this screen appears again. follow these steps:

  check to make sure any new hardware or software is installed correctly.

  If it is a new installation. Ask the manufacturer of your hardware or software for any windows update you might need.

  If the problem persists. disable or remove any newly installed hardware or software. Disable BIOS memory option such as caching or shading if you need to use safe mode to remove or disable components, restart your computer, press F8 to select advanced startup options. then select Safe mode.

  Technical information:

  STOP: 0 X 00000050 (0XF7895726, 0X00000000, 0X00000000)

  Partmgr.sys - address F7895726 base at F7893000, DateStamp 00000000

  I ran the Dell cd dignostic is to show the following error message:
  Error Code 0F00:1344

  MSG DISK_0? Block 8: can? t read, replace the drive or remove the write protect

  The given error code and message can use Dell Technical Support to help diagnose the problem.

  Hello

  ·        Since when are you facing this problem?

  ·        Remember to make changes to the system?

  I suggest to unplug external devices such as printer, scanner, etc. that are plugged into the system, and then restart the system and check if the problem persists.

  Error code 0F00:1344 you listed are hard drive error codes. Usually, this means that the hard drive needs to be replaced. I suggest you to contact Dell support for assistance. Once the hard disk is fixed, you can try the methods mentioned below.

  Click on the link below, contact Dell technical support.

  http://en.community.Dell.com/support-forums/disk-drives/default.aspx

  Method 1:

  I suggest you to do a check disk from the recovery console and check if the problem is resolved. Follow the steps mentioned below.

  a. start into the recovery console using the XP CD. Follow the steps mentioned in the article below.

  Description of the Windows XP Recovery Console for advanced users

  http://support.Microsoft.com/kb/314058

  b. perform a disk check.

  How to perform disk error checking in Windows XP

  http://support.Microsoft.com/kb/315265

  Method 2:

  I suggest you to start with the XP CD and then do a system restore. Follow the steps mentioned in the article below.

  How do I recover from a corrupted registry that prevents Windows XP startup

  http://support.Microsoft.com/kb/307545

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit ourMicrosoft answers feedback Forum and let us know what you think.

• CLEANING THE DRIVE SYSTEM

  Whenever I browse the system disk is quickly exhausted or shrinks. How can I free up more space on this drive? My hard drive is 500 GB, the drive system takes 80 GB; Now, it has only 100 MB of free space. I need about 20 GB for effective performance; Bright clues?

  Hello

  You'd be surprised how many people ignore disk cleanup and cleaning of the new system file... Some people also navigate a large NUMBER of graphics, that can use a ton of temporary space.

  Recently, I came across something that at least sometimes, indicates that this is related to the indexing of research essentially going nuts... The file out of control seems to be... C:\ProgramData\Microsoft\Search\Data\Applications\Windows\Windows.edb...

  This file is located in an area that is locked, unless you have changed the Ownership\Permissions of the files, but you should be able to access the DATA and to check its file size to see if it is the culprit...

  If so, here are some links with more info...

  http://superuser.com/questions/59864/stopping-Microsoft-Search-from-eating-my-hard-drive

  http://windows7themes.NET/what-is-Windows-edb-can-i-delete-it-or-change-its-location.html

  There is another file for Windows that can do as well... I'll have to look for the info...

  Also... Your Windows\TEMP folders will only be cleaning after seven days. Which may or may not be what that suddenly erased.

• Have installed Photoshop CS4. Replaced the drive hard and now I get error code 150:30. What should I do to get it working again

  Have installed Photoshop CS4. Replaced the drive hard and now I get error code 150:30. What should I do to get it working again

  Migration of CS4 breaks the license. That's what 150:30 means. Assuming you are using a Mac.

  You can use the Terminal method to repair the license... but I stress that carefully read you and understand the instructions here before you run it. beginning

  # 11. https://forums.Adobe.com/thread/1714695

  If this isn't what you want to do, you have to reinstall.

  Gene

• How can I replace the old system of comments by Disqus?

  How can I replace the old system of Business Catalyst with Disqus comments? Help, please

  The universal integration for Disqus code is just javascript.  You must register for an account on http://disqus.com/for-websites/ and set up your account first.  Once you have changed your settings, click on the link 'Install' and which will give you code javascript to add to your pages as well as a few other tips to make it work.

• Had to replace the motherboard: System does not boot, the XP installation disc runs to a failure.

  Thus, the motherboard in my PC started to die.  I replaced it.  Start-up of the new system has prompted a Safe Mode boot.  Choose Safe Mode, the system restarts after mup.sys.  Choose the last known good startup the initial windows screen appears briefly, then restart the system.  Boot from the original installation disk, all kinds of drivers charge then the last message that appears is loading Windows Executive.  A
  BSOD appears stating something to the effect of an error with the hard drive, verify the presence of virus, remove the new hard disks, etc..  Hard drives is a virus.  So, how do you round a re - install defective and/or repair or a defective Mode start safe mode with new material?

  Thank you

  Hello

  Since you have replaced the motherboard, you may need to reinstall the operating system.
  Reference:
  http://Windows.Microsoft.com/en-us/Windows/help/install-reinstall-uninstall

  Thanks and greetings
  Umesh P - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  [If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message.] [Marking a post as answer, or relatively useful, you help others find the answer more quickly.]

• My motherboard is dead and I need to replace my drive system as well as

  My motherboard is dead and I need to replace it. Unfortunately, this will be a completely different map (brand and model).

  My old system drive is IDE but the MB will not accept imput without an IDE interface card.

  I have the interface card, but don't think it will work to re - install through this forum

  I have a (relatively) new SATA I don't mind that I can install the operating system (windows 7 pro) now, but here the reformatting is trapped. How can I transfer all installed programs and settings from the old system to the new system disk drive after that I re - install windows

  Cannot create a new image or anything of that nature that the system is dead.

  I have backups, but not too recent

  You will need to reinstall your programs and drivers for other devices, you cannot be transferred.

  You can recover your data by installing the hard disk in a 3.5 external USB box and copy your files. Connect it to your computer then take possession of the files in your account folder in the directory of the user on the old disk.

  Take ownership of files and folders:

  How to: Make a file/folder in Windows 7

  Amazon.com: New 3.5external HDD hard drive USB enclosure 2.0

  If it is a portable hard drive:

  DX - SATAUSB 2.0 HDD case 2.5

• Replacing the drive HARD on Portege R700

  Hello

  I just ordered a R700 and hope to upgrade the HARD drive of 320 GB for one SSD OCZ Vertex 2.
  Is it easy to replace the hard drive in the R700? Should I remove the keyboard is a Panel on the back?
  What size hard disk will - 2.5 "or 1.8"?
  A SSD will be simply connect using existing connections, or something else there?

  See you soon.

  According to the specifications of the laptop Portege R700 has 2.5 HARD drive is HDD with SATA interface, so I think that you should order 2.5 SSD with standard SATA connectors.

  HARD drive is placed on the bottom side near the cooling vent and it is fixed with a screw only.

  Remove the screws and HARD drive. You will see how the HARD disc is placed and how it must be removed.
  It's very simple and you can do it alone.

• Replacing the drive HARD Satellite Pro 4280

  I have a SP 4280 and the original hard drive on it does not have earlier. I bought a Hitachi Travelstar 5K 100 40 GB replacement, but I can't seem to make it work. FDisk recognizes the disc as a 40 GB drive and seems to format the drive. However, attempts to write anything to generate results in an error message "invalid media".

  Installation using XP Pro format the drive gives me an error message in the sense of "Windows cannot format the drive.

  I have attached the drive to my PC via a cable of adapter 2.5 "and it seems to work fine. I also use the latest version of the BIOS on my laptop. It is not the settings of 'cable' rider select and 0/1 on the drive.

  Someone knows what the problem is, or that I couldn't do or have suggestions to raise my drive and running?

  Cheers in advance

  Hello

  Your device was shipped with a 6 GB HARD drive.
  In my opinion, the BIOS has a few problems with the recognition of the HARD drive because of the large size of HARD drive. Unfortunately, I put t see any possibility to solve the problem.

• Replacing the drive HARD on Satellite C850

  I found this Toshiba on Youtube video that shows how to replace the hard drive on the C850.
  http://www.YouTube.com/watch?v=0550V-181d0

  It helped me a lot, because there is NO entry in the user manual on how to replace it and where the hard drive can be placed.

  They show you where is the memory, but not where is the hard drive. WTF? so, this video tells you it's in the same slot for memory.

  Hello

  Yes, I also noticed that not all information can be found in single user manuals.
  However, there are many other sources to find essential details.

  Toshiba Europe youtube channel seems to offer a lot of useful videos to replace the HARD drive, memory or a drive CD/DVD in the different laptop models.
  http://www.YouTube.com/user/toshibaeuropesupport

• Satellite Pro A60: How to replace the drive?

  Satellite Pro A60 replace DVD player - need repair
  Or does anyone know how to remove the drive of this laptop Bay

  Post edited by: chrielli

  Hello

  I think the disk replacement procedure is very similar to replacements on other laptops.
  To remove the STRANGE bay module follow these steps:

  1. turn the computer.
  2. remove the black binding screws.
  3 turn the computer over and open the display.
  4. push the module bay ODD.

  All that s. It s not achieved with a screw.

• Replace the drive of my laptop in a Toshiba Satellite 5100/5105 - experience?

  I intend to replace the defective CDRW/DVD drive in my Toshiba Satellite 5100 503 (European version, it was sold as 5105 in the United States and other countries).
  The disk is a UJDA730.
  Update, I consider the much appreciated a Slimline DVD +/-RW drive. Unfortunately, some internet research revealed that the upgrade to optical laptop drive is not as simple as one would hope. I had no trouble to remove my old drive (just remove the keyboard and unscrew the two screws), so I consider myself to be able to put in a new drive instead. However, two problems remain:

  -mechanical compatibility: the 6500 has seems to have a different layout of collar. The eject button and the LED are in a different position from that of my current drive, so I doubt I'll be able to use my old glasses with it. In addition, the bezel from my old drive has a niche in the lower right corner (similar to that found on some laptop computers Fujitsu-Siemens), which gives place to the volume control on the laptop. So I can't reuse the old bezel and bezel of the NEC will probably not allow me to close the CD tray. I wonder if some Dremel work on the plastic parts of the NEC drive will allow me to physically. Anyone who has tried?

  -electronic compatibility: computer laptop drives don't usually have jumpers to change their configuration of master/slave/cable selection. Instead it is located in the firmware, change so it is flashing a new firmware, which is not easy to find and hard to do if your drive is still not recognized. SO I need to know if my notebooks is the optical drive set to master, slave. CSEL or 'inverse cable select. " Can someone help me here, either by own experience pointing me to a relevant source on the web?

  Hello

  as a first step in a Satellite 5100 CD player is fixed mounted and can only be replaced with the same model! Another model might work, but as you can see the bezel fits and maybe the new drive does not match 100%. So you will have problems all the way!

  What do you think about an external solution via USB or Firewire. It's the best way to upgrade!

  To bye chris

• Tecra 8000: Cannot start - Message "Insert disc in the drive system" lights

  I have a Tecra 8000, I've not used for about two months. Now when I try to start the "Disk system to insert in the drive" message on the display. I tried three disks in the system, but they have not been accepted and the same message appears. I visited in the 'setup' and changed priorities and tried to floppy, CD-ROM, HARD disk drive, and the same message every time. Is it possible that the internal battery "backup" is completely flat?

  Hello

  Well, I'm not sure about your suggestion of the bios battery. Usually, you will see an error massage low battery BIOS or CMOS battery low.
  Well, but if the battery is low, so all settings are disabled and the BIOS can't save the changes.
  It's not easy to say what the problem is. If there is something wrong with the material if you ask ASP for help.

• Replace the drive in Satellite L500D 13 c - recommendations

  Hello!

  I plan to replace the HARD drive (5400 RPM) underway with a new, more fast (7200 RPM) HDD in my Toshiba Satellite L500D - 13 c. The question is how much it will improve the overall performance of my laptop.

  The second question is whether it's hard to replace the HARD drive in this notebook. I'm not a great computer, but I'm pretty handy in general so I'm willing to try if this isn't great risk.

  Earlier, I was thinking about upgrading the RAM (from 4 to 8 GB) in the same notebook, but it seems as if there is no support RAM Pentecost 8 GB of capacity. Anyone who has had the same thoughts?

  Any help or thoughts on this is much appreciated.

  See you soon!

  Anders

  Replacing the HARD drive is not problematic and, in my opinion, free for guests, so no risk guarantee valid for laptop for you to avoid. Check the user s manuals document. Maybe you will find a description how to do this.

  My personal opinion is that the HARD drive with a faster HARD drive upgrade is not necessary. HARD drive will be a bit faster but, in my experience, faster hard drives produce more heat too so it can happen that the Briefcase for laptop computer where the HARD drive is placed will be a little warmer than before.

  What is the reason for the upgrade of the HARD drive? Just better performance of the laptop?

• failure message after replacing the drive #2 0203 IDE

  My DVD is UJ - 820B and I replaced it with exactly the same.
  The dif is that the former is FW: 1.00 while the other is FW: 1.05
  1. is the only solution to fix the PIN? If Yes can you pls confirm with pins.
  2. the IDE #2 error means that: Bay DVD is on primary slave while the DVD is secondary master or vice versa?

  Can is it you further please let me know.
  If you wish to contact me by e-mail at [email protected]

  I guess that the CD/DVD drive supports another setting master/slave/c-salt.
  FDI #2 error is displayed because the BIOS can't recognize the drive correctly.

  The problem is that it of not possible to change these settings as on external drives by changing the rider a special internal firmware control these settings.

  You suggested that the reader is the same but the firmware is different.
  Well, in my opinion, that's a reason for the issue