Required for ESXi firewall ports

Similar Questions

• Required for NAC firewall ports manager manage/add the Cisco switch

  Hello

  I am trying to add switches cisco for the NAM, but I am not able to add the switch I get the error "unable to control switch" I tried opening ports 161-162 on the firwall; If I were to allow all traffic between the NAM and the switch, cisco NAM is able to add/manage the switch.

  Do not know what are the other ports may be required for cisco NAM for managing the switch?

  Thank you.

  Hello

  As far as I KNOW, only UDP 161 and 162 for SNMP communication ports must be open.

  Please make sure that you have configured the correct port on the switch:

  (config)# snmp-server host 172.16.1.61 traps version 2c cam_v2 udp-port 162 mac-notification snmp 

  If still does not, I would check the logs on the firewall for any traffic blocked between the cam and the switch.

  HTH,

  Tiago

  --

  If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

• Hardware requirements for ESXi 4

  Hello

  What are the minimum hardware requirements for ESXi 4 requirements?

  I can test it on a P4 / 1 GB RAM workstation with 20 GB hard drive and add a NAS 1 TB as a data store?

  The basic material may or may not support ESXi. The components shipped as disk controllers and network adapters are often problems for installation. You can check your hardware against the HCL http://www.vmware.com/resources/compatibility/search.php or http://vm-help.com whitebox Web site list.

• Minimum hardware requirements for ESXi 5

  Hello

  I am a newbie of virtualization and ESXi so please help me on these issues:

  I intend to host 1 Windows 2008 Server and 1 Pfsense on the same host with ESXi. The two servers to serve a small number of users (less than 10). The Win2k8 runs just small .NET application and the just Pfsense will act as a router/gateway for web portal (without VPN, nothing complicated here).

  I checked the minimum requirements for VMWare ESXi here (KB VMware: minimum system requirements for installing ESX/ESXi) but still uncertain before buying new equipment to run ESXi because the specifications said ESXi only works on 64-bit x 86 CPU.

  I'm looking at this PC:

  CPU: Processor Intel® Celeron® 1037U (2 MB Cache, 1.80 GHz)

  RAM: 8G RAM Support memory DDR3 2 G / 4G / 8G / 16G, DDR3 1333 / 1600 MHz

  Storage: 64G SSD

  
  

  ESXi will install OK on this system?

  
  

  Thank you
  

  Hello

  Intel http://ark.intel.com/products/71995/Intel-Celeron-Processor-1037U-2M-Cache-1_80-GHz CPU specs this should work in general, but can cause performance problems as this Celeron has only 2 hearts.

  Another thing to consider is the RAM, ESXi 5.5 OS takes about 4 GB of RAM on the 8 GB leaving you 4 GB for VMs Windows 2008 with less than 4 GB wil be quite slow and sooner or later begin to swap to disk.

  Also the motherboard used is something check with HCL as at the storage controller and connect it on Board should be compatible.

  The road easier to go is to get the material at the level of the server that is listed in the HCL, you can find systems awarded new/used being fully compatible. It would be much more reliable than the construction of a whitebox on office equipment system.

  cykVM

• The requirements for standby Firewall ASA

  Hello

  I have ASA 5510 firewall with security more license bundle is running in our production environment, and I am now to buy another box for Firewall ensures according to my understanding, the wait should be same as an active firewall.

  Here are the specifications for this run into our existing environment

  1 ASA 5510 Firewall (security more Bundle license, 1 GB RAM, 256 MB Flash)

  And buy the replica of above with security @ License bundle, 1 GB RAM, 256 MB of memory Flash.

  My question is, is there anything else that I'm missing for the firewall to sleep?

  Kind regards

  Saeed

  ASA failover partners must have the same number?

  Hereby I guess that you are referring to the same number of interfaces.  These interfaces must also be of the same type.  so you can't have an ASA with 4 interfaces of concert and the other with 2 interfaces Gig.  Or you can, but you will not be able to use the failover for 2 of the interfaces on the SAA with 4 Gig interfaces.  Similarly, if both ASAs have 4 interfaces but an ASA has 4 interfaces Gig while the other has 4 Fastethernet interfaces, then this only would be not supported.

  --

  Please do not forget to select a correct answer and rate useful posts

• Hardware requirements for ESXi

  Can someone tell me please the hardware requirements specifications. Setup an ESXi server.

  Hello

  This can help you, http://www.vmware.com/resources/compatibility/pdf/vi_systems_guide.pdf

  Thank you

  Samir

  PS: If you think the answer is useful please consider rewarding points.

• Cisco Clean Access Update website and Firewall Port required

  Hello

  I was wondering if anyone might know the site that would be to use the clean Access Manager to put as well as the required firewall port. This is due to a firewall in place. From reading, do not know if it uses another website besides as the next http://www.perfigo.com/clean_machine_1/version-se.txt on port 80.

  Thank you.

  Hello

  For CAM checks and update the rules, this is the only site required.

  HTH,

  Faisal

  --

  If you find this article useful, please note so that others can easily find the answer

• Permisions required for mounting NFS on ESXi host

  Hi team,

  In our java application uses) use API VMWARE to mount the NFS datastore on the ESXi host. But to do this, we need the ESXI root permissions. Because having credentials root door reached the safety of the system, we would like to create a user with the required permissions will be sufficient to add the mounting NFS on ESXi host.

  But do not know how to see the permissions required for the Assembly of the NFS on ESXi host. Pointers would be useful.

  Thanks in advance,

  Anjana

  Hello

  Storage permissions lies in the roles of Group of data store.

  You should have a default profile role of storage in your vCenter.

  Cheque image:

  

  Hope this helps

• separate subnets for the ESX/ESXi management ports (vMotion, manage, FT, etc..)

  Is it better to have all of your VMKernel ports on the same subnet or subnets separate (one for each role, iSCSI, management, vMotion, FT)?  Are their potential problems with either scenario?  Please include the ESX and ESXi.  I want to get my setup just as it should. Please let me know also if you need additional information.

  I have licenses for ESX and ESXi, but I'm leaning toward ESXi are all vSphere 4 Update 1.

  Hello

  In fact, you have to use separate subnets for your vmkernel ports but they can run on the same thread. You can share a subnet between a vmkernel and service console, but not between two vmkernels. Just like that. So yes, you need to use several subnets.

  Best regards
  Edward L. Haletky VMware communities user moderator, VMware vExpert 2009

  Now available: url = http://www.astroarch.com/wiki/index.php/VMware_Virtual_Infrastructure_Security'VMware vSphere (TM) and Virtual Infrastructure Security' [/ URL]

  Also available url = http://www.astroarch.com/wiki/index.php/VMWare_ESX_Server_in_the_Enterprise"VMWare ESX Server in the enterprise" [url]

  Blogs: url = http://www.virtualizationpractice.comvirtualization practice [/ URL] | URL = http://www.astroarch.com/blog Blue Gears [url] | URL = http://itknowledgeexchange.techtarget.com/virtualization-pro/ TechTarget [url] | URL = http://www.networkworld.com/community/haletky Global network [url]

  Podcast: url = http://www.astroarch.com/wiki/index.php/Virtualization_Security_Round_Table_Podcastvirtualization security Table round Podcast [url] | Twitter: url = http://www.twitter.com/TexiwillTexiwll [/ URL]

• What Win XP driver is required for the port DV on a Satellite Pro P100

  Which driver "specifically" is held by Win XP on a Satellite Pro P100 DV port?
  Toshiba provides this driver on the download page?

  Win XP does not recognize the camera into the DV port.
  It does not recognize the camera a few months ago but not detect it when it is connected.

  I don't know what changes have been made since then. Can I simply re - install the proper drivers?

  Thanks in advance.
  Tom

  Hello

  DV port? Do you mean the iLink (firewire port)?
  You have a camcorder?

  I can connect my camcorder to the laptop using the firewire cable and firewire port.
  There is no special driver for the firewire port. The Windows operating system contains the own drivers that control this port.

  Maybe you should remove the device and then Manager should restart the operating system. This allows to recognize the FireWire again

• HP Elite 8200: Windows Driver required for Port 10 series PCI VEN_8086 & DEV_1C3D & SUBSYS_1495103C & REV_04

  I installed Windows 7 Pro to Windows 10 Pro, and now I don't have a driver for the Serial Port PCI (VEN_8086 & DEV_1C3D & SUBSYS_1495103C & REV_04).  I read on other forums of this issue in the forums, but I can't find the spxxxx files in my C drive.

  Hello:

  You need this driver...

  This package contains the driver Intel Active Management Technology (AMT) for the supported models running a supported operating system.

  FTP://ftp.HP.com/pub/SoftPaq/sp69501-70000/sp69506.exe

• What are the network requirements for the remote server of the Panel?

  What are the network requirements for the remote server of the Panel?

  I tried for awhile now to set up a Control Board.  I can connect to my remote panel of computers from other computers on my local network but nowhere else.

  Whenever I use web publishing tool gives me a URL in this format: Http://Computer-Name.Corporate-Name.local:8086 / VI - nom.html apparently it means I have a local DNS server and this URL is meaningless to the public.

  When I try to connect with the Operate > Connect to... remote control, I get this error message:

  "Connection to Server remote panel...".
  "Connection refused by the server remote control specified: make sure that the LabVIEW Web server is enabled on the specified server.

  I got the same error when I tried to host a remote panel from my laptop at home, on my Wi - Fi.  Is there some network settings or firewall I'm not seting?  Would it be my server or the router or the private network?

  My goal is to be able to host remote panels of my laptop while I'm on the international scene, creating using 4 G internet mobile.  Is it still feasible?

  As he Turners on my router had to be put in place so that my Port is in the rage of transfer.  Also I had to disable DHCP.  Without that you cannot host behind a router.

  These are the instructions I put fallow:http://digital.ni.com/public.nsf/allkb/B1E9A3D78BAED949862573AD0065D4D2

• How do I configure Openfiler for ESXi 5.0 (on which has been installed in the workstation).

  9.0 pre-installed VMware I installed in my laptop. I created a 5.0 as a VM ESXi in workstation. And I installed vSphere client 5.0 in my laptop. And I am able to access ESXi from my laptop through the vSphere client.

  Now, I created a VM with Windows 2008 R2 on top of ESXi. I installed vCenter 5.0 in Windows 2008 R2 Machine. I have just to connect to vCenter using vSphere client (which has been installed in my laptop) and added ESXi as host in the inventory.

  Now, I created a VM with Openfiler. Everything is fine. I want to use this Openfiler as a storage array, and I want the SAN with ESXi and Openfiler configuration.

  I think I need to create a VMkernel port group and attach that Openfiler VM who. And if I want to access the Openfiler web interface, do I need to have internet access? We can access the Openfiler Web interface without having access to the internet?

  Can someone let me know how to connect this Openfiler as a storage Bay for ESXi and configure a San.

  Openfiler does not need Internet access and you do not require an additional VMkernel port for access.  If it's production, you share the management and traffic on NIC iSCSI physical separate and thus vmkernel ports.  In this case, it is not necessary.  Did you do the initial installation of Openfiler to create a LUN for the ESXi host access?

• Requirements for networking for HA / DRS

  How exactly the configuration of the virtual switches and their ports groups, as well as physical NICS on a cluster of ESX servers must be for HA and DRS to work?  All physical servers you need the exact number of groups of ports on the exact same virtual switches connected to the

  exactly the same cards NIC physical and with the same policies accurate to team/redunancy and so on?

  What are the bare minimum requirements of which must match the network configuration of the ESX servers so that HA / DRS to work?

  Thank you

  VMware HA strictly require a host "heartbeat" interface

  It is usually the Service Console (for ESX) or the (for ESXi) management interface.

  HA require seamless networking, so don't forget to use the same network address and the same mask.

  VMware DRS is based on vMotion, requiring several things.

  Network side, it requires a vmkernel interface (marked as vMotion) enabled.

  It is better if it is on another network (physical or VLAN).

  Finally, HA and DRS around the virtual computer on other host... So, the network point of view, you must have as homogeneous networks of VM (same VM portgroup label and vSwitch connected to the same physical networks).

  André

• Can someone link me to some documents that NetBIOS is required for devices inherited from Windows to function properly?

  NetBIOS and Windows Legacy Machines

  Can someone link me to some documents that NetBIOS is required for devices inherited from Windows to function properly?

  Maybe even a link to a Microsoft web page that States this as well.

  I understand the security risks inherent with opening ports 135 and 139, but they are needed within the network for some devices to function correctly, just need a documentation that indicates that.

  Hello

  See the links below and check if that helps.

  http://TechNet.Microsoft.com/en-us/library/bb727013.aspx

  http://TechNet.Microsoft.com/en-us/library/cc940063.aspx

  http://TechNet.Microsoft.com/en-us/library/cc738412 (WS.10) .aspx

  Thank you