Requirements for vSphere remote site replication

Similar Questions

• What are the network requirements for the remote server of the Panel?

  What are the network requirements for the remote server of the Panel?

  I tried for awhile now to set up a Control Board.  I can connect to my remote panel of computers from other computers on my local network but nowhere else.

  Whenever I use web publishing tool gives me a URL in this format: Http://Computer-Name.Corporate-Name.local:8086 / VI - nom.html apparently it means I have a local DNS server and this URL is meaningless to the public.

  When I try to connect with the Operate > Connect to... remote control, I get this error message:

  "Connection to Server remote panel...".
  "Connection refused by the server remote control specified: make sure that the LabVIEW Web server is enabled on the specified server.

  I got the same error when I tried to host a remote panel from my laptop at home, on my Wi - Fi.  Is there some network settings or firewall I'm not seting?  Would it be my server or the router or the private network?

  My goal is to be able to host remote panels of my laptop while I'm on the international scene, creating using 4 G internet mobile.  Is it still feasible?

  As he Turners on my router had to be put in place so that my Port is in the rage of transfer.  Also I had to disable DHCP.  Without that you cannot host behind a router.

  These are the instructions I put fallow:http://digital.ni.com/public.nsf/allkb/B1E9A3D78BAED949862573AD0065D4D2

• Remote Site Replication

  Hello, I am currently using vSphere 5.1 replication and replication of my production SAN EquilLogic on a little SAN Synology on the same subnet on my local network. I have a data store in my vSphere cluster using iSCSI to Synology for local replication of my VM.

  My company has another office in Seattle that I would use as my recovery site and settle the Synology SAN, so that I do not have the localized replication happening. I am a little confused everything is...

  1. Should I try to keep the connection iSCSI on my WAN link to our Seattle Office that 10mgps on MPLS for the Synology?
     
  2. Or do I need to configure another host of vSphere, tie my Synology and attach it as a remote site in vSphere replication?
     

  Thank you, Eric

  you will probably better use another host using VR because over a 10Mbits/s connection, latency will probably cause the iscsi connection Flake at any given time.

• PIX 515E for VPN remote site

  Hello

  7.0 (1) version pix

  ASDM version 5.0 (1)

  I have a situation where you go paas-thanks to the VPN feature goes on our PIX 515E. I tried to put this on the pix using a VPN Wizard Site to site

  who is enabled. I was unable to connect to the pix from the remote site. Witch's journal replied negotiate the pix is OK and the success

  The problem is when I try to set up the tunnel to the top of the remote site. I fall without failure.

  where can I see the vpn pix for error log?

  is there a manual for the solution of site to site VPN using the wizard

  Help, please.

  Thanks in advance

  http://www.Cisco.com/en/us/partner/products/HW/vpndevc/ps2030/products_configuration_example09186a00804acfea.shtml#ASDM

  the section 'use adsm' (step 14) gives an example on how to set up vpn lan - lan via adsm

  Newspaper to go to the section "check".

• Best practices for controlling Remote Sites ESX servers

  Hi all

  I was wondering what the best practices or the options are for the management of the ESX servers in remote offices or branch.  I know that you can always use the VI to control on the site server, but what happens if you want to use some of the functions of the virtual Center?  How remotely manage and leverage capacity of Virutal Center in remote sites or branch offices, since you can't have Virutal Center installed in a domain.

  Other then a VPN dedicated to all remote offices or a branch is there another way to use Virtual Center to remotely manage the ESX servers in remote offices or branch?

  What are your current plans DR if the main site is going to host VC?

  You can run your VC in a VM and have power clone on a remote site or both incase of total failure.

  Then with the help of RCL etc. under the texiwill recommend and/or vMotion VM VC to other sites if necessary.

  Andy, VMware Certified Professional (VCP), http://www.vmadmin.co.uk/

  If you have found this information useful please give points by using the buttons at the top of the page accordingly.

• Port Requirment for monitoring remotely with the Infrastructure Officer.

  Hi all

  Quick question, I have a Windows 2008 host in 'DataCenterA' that I installed a local Agent Manager and have deployed the agent infrastructure (5.6.6)

  I want to monitor a host Windows 2008 in 'DataCenterB '. I set this up, but I am told alarm

  Could not establish a connection to the lo3wpfogfms001.dcsprod.dcsroot.local: HTTP request failed [caused by: denied connection to http://lo3wpfogfms001.dcsprod.dcsroot.local:5985]

  This would be due to a firewall blocknig this port. If telnet to this port also fails instantly?

  If so this agent always uses this port?

  Hello Mike,.

  Have you configured listener winrm 'l03wpfogfms001 '?  5985 is the default listening port

  http://eDOCS.quest.com/Foglight/565/doc/core/FglAMInstallation/WindowsConfig.073.3.php

  Also, have you checked to see if your RPC service is running?  Also please check for all antivirus software.

  The fglam use WMI If WinRM fails.

• Script required for vsphere

  PowerShell script to extract the information below the selected clusters.

  ESX connectivity to data warehouses

  ESX network connectivity,

  HA settings

  ESX patch level

  HBA Firmware

  PowerPath installion conformation.

  Thanks in advance.

  Hi Vivari, as a suggestion I would start with RVTools (free utility to extract common vCenter data)...  It allows export to Excel and a good utility to use if you do not know PowerCLI scripting.  Although RVTools is a good util it will collect all the information you're looking for.

  You are looking for it in a report, or is it possible to collect from several sources?

  It is not an easy way to collect HBA Firmware levels without connecting to the host ESX via SSH.

  Use RVTools to data warehouses, networks and ESX patch levels.

  If you cannot collect the information you're looking for using RVTools PowerCLI scripts would be the next option.

  Script to collect the NIC and HBA Firmware.

  http://vblog.Strutt.org.UK/2012/04/ESX-HBA-and-NIC-driverfirmware-versions/

  HA cluster settings: (this command will show if HA is activated and the level of failover HA) is what you are looking for?

  Get-Cluster ClusterNameGoesHere

  PowerPath:

  http://communities.VMware.com/thread/404405

  Get-VMHost |
  Select Name,@{N="PowerPath";E={
    $pp = Get-VMHostPatch -VMHost $_ | where {$_.Description -like "*PowerPath*"}
    if($pp){$pp.Description}
    else{"Not present"}
  }}
  

  It is always best to include as much information you are looking for during the validation of the community.

  This should help you get started.  If you need this in a single report please answer by one example data and put on the page you are looking for.

  Kind regards

  JayLB

• Can also interface with VPN remote site also for another use?

  Hi all

  An interface used for the remote site VPN on PIX can be used for another function, for example for the smtp server and web publishing?

  Thank you!

  Best regards

  Teru Lei

  Yes! of course you can. Just try it.

  --

  Alexis Fidalgo

  Systems engineer

  AT & T Argentina

• Remote site 2 Internet connections...

  I have a remote office that currently connects to a data center Central via the VPN Site to Site.  I get a 2nd internet connection like a fall back to the remote desktop.  How to configure the Site to Site VPN working properly so that if the main internet connection goes down, the site switches to the secondary?

  On internet connections remotely come from different providers so that they have completely different blocks of public IP addresses.

  Central

  ASA 5520 8.0 (4)

  GIG 0/0 public IP

  Remote

  ASA 5520 8.4 (1)

  GIG 0/0 public IP

  Public IP address of concert 0/3 (2nd internet)

  On the end of HQ you must enter the new IP address of the ISP (for the remote site) as secondary peer.

  On the remote end, you must add SLA so that traffic will be redirected on the second link incase of primary failure.

  Search the forum you will find many Ref assignment to this scenario. Here is one...

  https://supportforums.Cisco.com/message/3452739#3452739

  HTH

  MS

• Can not pair sites in vSphere 6.1 replication

  Hi all

  I am faced with an error during the twinning of sites. Used to work in version 5.5 replication, but after upgrade, I can't pair it sites. DR location was built from scratch, with the same names for esx, vcenter and RV appliance servers. Also on the site main VR device was installed from scratch, only vcenter me lie down to version 6.x (latest)

  Now when I wan't to pair a sites that I get this error after the connection is successfully to the server DR CSP:

  

  and in hms.log:

  

  Network is not a problem, because before upgarde replication worked without any problem, also I filled files hosts with respective titles on each of the sites, then ping with the FULL domain in labor OK.

  Any idea?

  To advance.

  / R.

  After adding port 443 excluding firewall the phairin fine.

  VMware needs to update the ports requirements in the documentation: VMware KB: numbers of ports that should be opened for vSphere 5.8.x and 6.0 replication

• The amount of data required for replication?

  I have a client with a server 2012R2 as a domain controller configuration. It has SQL express for shipping system. There are 3 full-time and part-time users 2.

  They had a Server 2003 with Replay. Replication stored up to my office to the problem. Only the internet expanded wireless or Verizon or Hughesnet.

  They use the wireless extended for about 5 years. The upload speed has slowed down to about 40 KB/s on May 7, when they did an upgrade. It's part of the problem.

  Replication is about 100 hours of delay at this time.

  Verizon has a 10 GB per month maximum. HughesNet has 50 GB a month for $129.00

  If I'm fiquring right 40 KB/S = 100GB per month so Appassure sent to the amount of data to use HughesNet.

  I do snaps at every 30 min. It is an average of 200 MB. I moved the page file to a volume that save. I turned off a bouquet of services.

  I think that I could copy the data into my office with far less bandwidth than that.

  "The upload speed has slowed down to about 40 KB/s on May 7, when they made an upgrade."

  -So, who did an upgrade? Verizon, Hughesnet or Appassure (from 4 to 5?)

  -How will you measure this 40 KB, Speedtest.NET, a field in Appassure?

  "They are on an average of 200 MB"

  -Where are you number of 200 MB of? The number, 200 MB perhaps before any treatment is done. So you might not really need to transfer some 200 MB through

  Do you make backups every 30 minutes throughout the day? Does include weekends? If people do not work on weekends, make sure that you don't do backups on the weekend, which falls a little less than 80 GB per month.

  Drop your freq from 30 minutes to 1 hour, which reduces your amount to be transferred in the half.

  If people work 04:52, don't make backups 8-5, this significantly reduced backups.

  If you set backups to run every hour, from Monday to Friday and 8-5 you would subject under 9 GB per week or 36 by number of months vs Antons 271 GB

  You have to replicate this customer?

  Even if you get this working, the next time that the client makes Inc. vs FULL, you will be FAR behind. And customers seem to like make full backups.

  I don't envy you, you have to solve the problems Appassure did and they don't give you any idea what it is. They will not tell you what changes, how long they are taking every step to prepare backups and replication. Why their yield is 40 KB. They will tell you (as above) to use 3rd party tools to try to measure their performance applications and its basically impossible

  She's really looks like Appassure may not be a good fit for this site because of the way they perform backups and your needs. If you can't resolve your needs to work with Appassure, I would look at other products that work well for remote sites and a small number of customers. If you have any questions, feel free to PM me

• What is the function of the IOS minimum set required for VPN site-to-site software?

  Hi guys,.

  I have a Cisco 1841 router to do a VPN site-to site. I would like to know what is the function of the IOS minimum set required for VPN site-to-site software?

  Thanks in advance.

  Hi Ja,

  Advanced security or more should do it. The version of the IOS, you can try later 12.4 T which is c1841-advsecurityk9 - mz.124 - 24.T5.bin, in which case you don't want to go to 15.1 still.

  I hope this helps.

  Raga

• How to calculate what bandwidth is required for a site of Dataguard

  Hello
  
  We are running 11 g R2 RAC two nodes on windows 2008 R2 servers. We intend to build Dataguard site with the plug of the same or higher. For this reason, could someone please let me know that, how can I calculate the bandwidth required for site-based dataguard
  
  activity in our production environment? Is there any kind of method to help I can calculate the requirment of current bandwidth for my database of production in Mbps?
  
  Any help would be appreciated!

  Handle: 53637
  Status level: Rookie (25)
  Join date: June 26, 2003
  Messages total: 559
  Total issues: 61 (46 pending)
  Name shan
  Rental Australia
  Consultant Oracle occupation

  Also, try to close your message please

• Download at remote site for the 1st time

  What whatsoever to the next line, before you put the page online at the remote site, please?
  
  <! DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01 Transitional / / IN".
  " http://www.w3.org/TR/html4/loose.dtd" >

  NO.

  --
  Bryan Ashcraft (remove the BRAIN to respond)
  Web application developer
  Wright Medical Technology, Inc.
  -------------------------------------------------------------------------
  Macromedia Dreamweaver Developer certified
  Adobe Community Expert (DW): http://www.adobe.com/communities/experts/

  "Karlhevera" wrote in message
  News:fnvosu$GT1$1@forums. Macromedia.com...
  > To do anything at the next line, before loading the page for
  > the
  > distance from the site, please?
  >
  > > " http://www.w3.org/TR/html4/loose.dtd" >
  >

• Disaster recovery with replication for VSphere

  Am just test VSphere 5 of replication. with a couple of test VMs

  The replication process works very well

  What I want to know is the process to recover a VM replicated to new hardware in the case of the complete failure of the original host and/or data store

  In essence, disaster recovery.

  Are there other parts (software), that I need to take the replica VMDK and files related to re - create a new virtual machine on a new host

  Steve

  Yes, because it will be all your hard and .vmx files.