Restart the computer cause printer 'disappear '.

Similar Questions

• My printer will only print one page, then I have to restart the computer to print another

  The printer was fine since purchase, but recently, it will print a page after be on, then if I try to print a different document, he goes as far as the document taking up and looks like it's ready to print, then stops.  I tried to cancel the print job, but he will not - delete it then repeat "delete" in the print queue (but never removes it).  UN-plugging the printer is not clearly the print job.  The only way I can get to print the next thing is completely restart my computer.

  I tried to uninstall and reinstall the printer.  I put on all the latest updates for the printer... I am at a loss :(

  Does anyone have a suggestion?

  In the latest batch of updates to Windows, Microsoft has installed Internet Explorer 11. IE11 caused printer problems.

  Open Internet Explorer, click on help, then click about words of Internet Explorer. It should show the version here. If you IE11, then go to control panel, Windows Update, updates installed, look for Internet Explorer 11. Click Internet Explorer 11, uninstall.

  Restart the computer when you are prompted. Then see if your printer works.

  Rick

• HP LaserJet Pro CM1415: Printer will only print a single document. Bloggy queue and I need to restart the computer to print

  Printer will only print a single document. Bloggy queue and I have to restart my computer to print more than a single and repeat for each print job... very annoying. She's been doing this for printing the PDF, chrome, Word document, etc.

  Hello.

  Please, try the suggestions you find here:

  http://support.HP.com/us-en/document/c022054777

  Dovid

• Foxfire installed last week. Now printer is not working, websites does not open and Foxfire will not close unless I restart the computer.

  Can someone help me with the following problems:

  1 printer won't work because I installed Foxfire.

  2. I can search for a website but I can't open the Web site.

  3 foxfire does not close unless you restart the computer.

  If Firefox causes problems, get rid of it and use the Internet explorer 8: http://www.microsoft.com/windows/internet-explorer/default.aspx
  or Internet Explorer 9 RC: http://www.beautyoftheweb.com/

  teengeek.freehostingcloud.com Microsoft community contributor

• After the upgrade to 3.6 my FlashDrive falls down while I'm playing Farmville. I tried to update the flash player. I tried to restart the computer. Nothing works.

  Last night, my system was still using Firefox 3.5.8. I played Farmville on Facebook and everything worked well. This morning, I connect to my computer and find that I upgraded to Firefox 3.6. I tried to play Farmville all morning and Adobe Flash Player continues to break. I tried to update Flash Player. I tried to restart the computer. Nothing works.

  URL of affected sites

  http://Facebook.com

  Another potential cause of this problem is that the lock timeout is set too low:

  1. Select the address bar of Firefox (click or press CTRL + L)
  2. Type of topic: config and press enter
  3. Click on I'll be careful, I promise!
  4. in the filter box, type dom.ipc.plugins.timeoutSecs
  5. Double-click the setting and change the number.

  The default number is 10, for a default timeout of 10 seconds. Some games Flash can be slow and requires a higher setting. I would recommend to change that to 20 if you have problems with this.

  In addition, it would really help if people who encounter this problem let us know what games Flash is slow - and as soon as they are slow. Thank you!

• I want to know why when I restart the computer and save it that I restart the computer came out black background

  I just want to know why every time I restarted the computer I save then come out of the background is black, I put the f1 not the way I had before why now I guess that something is missing can fix you it for me please

  Hi linsugr,

  Do you know when this started?  The simplest solution because I have no idea of what is happened to cause this is to restore the system to a point BEFORE this problem started (and give it a a few days to be sure).  If you use Windows 7, see:http://www.sevenforums.com/tutorials/700-system-restore.html. If you are using Vista, see:http://www.howtogeek.com/howto/windows-vista/using-windows-vista-system-restore/. If you are using XP, see:http://www.bleepingcomputer.com/tutorials/tutorial56.html.  If the first attempt fails, try to go back a little further and see if you are met with success.

  I hope this helps.

  Good luck!

• computer will display a popup whenver restarting the computer, it says that mchd.exe is a problem

  Hello

  I have problem with my computer, when I start the computer it shows "computer will display a popup whenver restarting the computer, it says that mchd.exe is a problem" this error message and if I insert the USB the computer does not recognize the USB.

  Please let me know ASAP troubleshooting steps.

  Thank you & best regards

  Sashidara

  Hello

  I suggest that you start your computer in a clean boot state and check if the problem persists.

  Put your boot system helps determine if third-party applications or startup items are causing the problem. If so, you need to maybe contact the manufacturer of the program for updates or uninstall and reinstall the program.

  See the link below for more information on the clean boot troubleshooting.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note:

  How to configure Windows to use a Normal startup state

  After you have used the boot is a way to solve your problem, you can follow these steps to configure Windows XP to start normally.

  1. Click Startand then click run.
  2. Type msconfig and click OK.
     The System Configuration utility dialog box appears.
  3. Click the general tab, click Normal Startup - load all device drivers and services, and then click OK.
  4. When you are prompted, click restart to restart the computer.

• Sidebar gadgets are in random order each time I restart the application from the sidebar or I restart the computer.

  For some reason, whenever I restart the computer or I close the application of the sidebar and re - open in the start menu, my gadgets are in random order.

  I saw another thread for this on Microsoft Answers Social, but his problem was just after installation of SP2. I had SP2 for a long time and recently began to experience this.

  A moderator of Microsoft support proposed making sure that Java and Flash have been fully installed and implemented to date. I have both.

  However, due to a recent achievement in the platform of Adobe Flash (the one that allows the remote control, discovered last week), Adobe has proposed the Flash upgrade to the release candidate 7 (10.1) version. What I did. Could that be the cause? Hope not. If this is the case, then I will be happy to downshift until a solution has been found. However, the Java platform is perfectly updated and operational. And it's the 6.20 version, which is the latest public version.

  Well, I reformatted my hard drive and all restore factory settings.

  Everything worked fine... Until I installed again my Adobe CS5 Master Collection.

  So I started uninstalling the components one by one to see what worked...

  It turns out that Adobe Acrobat 9 Pro Extended (or rather the 64-bit extension him) makes the sidebar go haywire.

  Uninstalled Acrobat 9 and no problems yet. Restarted several times to make sure.

  I hope that one day I'll find an update to Acrobat who sets. Maybe I'll go post in the Adobe forums for that one.

  Whatever it is, no biggie for me - I barely use Acrobat.

• Internet Explore screen becomes milky and occasionally freezes forcing me to restart the computer

  Original title: freezes

  Internet Explore screen becomes milky and occasionally freezes forcing me to restart the computer.  now the Bureau is milky and freezes from time to time.  whenever the circle of 'thought' continues to 'think' without success.  Sometimes it fades, but most of the time I have to stop and restart.

  Hello

  Check if there is information in Event Viewer which may help us to solve the problem:

  http://Windows.Microsoft.com/en-us/Windows7/what-information-appears-in-event-logs-Event-Viewer

  Method 1:

  Step 1:

  Try to start in safe mode and check if you are able to stop normally. To start in safe mode follow the link given below.

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

   

  Step 2:

  If the problem does not occur in safe mode then boot to the desktop in normal mode and check that the third-party program is causing the problem. To configure your computer to clean boot follow the link below.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Method 2:

  Also, try to optimize the performance of Windows 7. Follow the link below which evokes the different ways to optimize the operating system.

  http://Windows.Microsoft.com/en-us/Windows7/optimize-Windows-7-for-better-performance

  Hope this information is useful.

  Amrita M

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• computer restored IBM won't let me go beyond the introduction of identy... closes and restarts the computer to the same: Enter name and ID... then again, it does the same thing. How can I save this monster?

  computer restored IBM won't let me go beyond the introduction of identy... closes and restarts the computer to the same: Enter name and ID... then again, it does the same thing.  How can I save this monster?

  Hello

  First, disconnect all the external devices connected to the computer, and then try to start and check what is happening. If the same happens, then you can try to start in safe mode and check if you are able to boot to the desktop. Only basic files and drivers needed to run Windows are started. If a problem doesn't reappear when you start in safe mode, you can eliminate the default settings and basic as possible cause device drivers. To start in safe mode follow the link.

  Start your computer in safe mode

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  Hope this information is useful.

  Amrita M

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Switches to color when you restart the computer profile or wakes from sleep

  I bought a Dell Inspiron 1470 with Windows 7 at home as a backup of my MacBook Pro.  I used the Spyder2Express to calibrate my screen that works well.  After that I restarted my PC the color profile has been enabled for a few short seconds, but then returned to the default setting, which is horribly blue and too bright.

  I then removed the color profile created by my Spyder2Express and used Windows' built in the calibration of the monitor.  Yet once, it worked until I rebooted the computer, or he woke from sleep mode.

  I then wen to the control panel-->--> the color management advanced and assured the new profile is the default value of the system.  The problem still remained after the computer is restarted.

  The only solution I have found so far is if after I restarted my pc I go to Panel of--> of color management and select and clear the checkbox "use my settings for this device."  My profile will then return until I restart the next time.

  As a pro photographer, it is a question that is extremely disappointing.  I searched forums, web, called Dell directly and none of this was of no help.  Any thoughts?

  Hi Mike,.

  It seems that software Spyder2Express adds color profile after each reboot. We can check if really Spyder2Express is the origin of the problem
  
  Method 1:
  Uninstall Spyder 2 express and check if the return of the issue after each reboot.
  
  Method 2:
  Configure the computer to boot and then refine the boot entry that is causing the problem
  
  Step 1: Perform a clean boot:
  Note If the computer is connected to a network, network policy settings may prevent you from following these steps. We recommend strongly that you do not use System Configuration utility to change startup options on the computer, unless a support engineer Microsoft directs you to do so. This can make the computer unusable.
  a. log in the computer using an account with administrator rights.
  b. Click Start, type msconfig.exe in the start search box and press ENTER to start the System Configuration utility.
  c. If you are prompted for an administrator password or for confirmation, type your password, or click on continue.
  d. under the general tab, click Selective startup, and then clear the check box load startup items. (The check box use the file Boot is not available.)
  e. on the Services tab, click to select the skin all the Microsoft services check box, and then click Disable all.
  Note following this step lets Microsoft services continue to operate. These services include networking, Plug-and-Play, record of events, error reporting, and other services. If you disable these services, you can permanently delete all restore points. Do not do this if you want to use to restore the system with the existing restore points.
  f. click OK and then click on restart.

  Step 2: Enable half the services
  
  a. click on the Services tab and then click to select the skin all the Microsoft services checkbox.
  b. Click to select half of the check boxes in the Service list.
  c. click OK and then click on restart.
   
  Solve the problem:
  After you determine the startup item or the service that is causing the problem, contact the manufacturer of the program to determine if the problem can be solved. Or, run the System Configuration utility, and then click to clear the check box of the element of the problem.

  Reset the computer to start as usual:
  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:
  a. Click Start, type msconfig.exe in the start search box and press ENTER.
  If you are prompted for an administrator password or for confirmation, type your password, or click on continue.
  On the general tab, click the Normal startup option, and then click OK.
  When you are prompted to restart the computer, click on restart.

  All the steps above to perform the clean boot is mentioned in the following article
  http://support.Microsoft.com/kb/929135

  Hope this helps,
  A Mir.

• I downloaded programs to see when I restart the computer they went

  I have a new computer with windows premium 7.

  I installed nero and downloaded other programs such as google, that they seemed to be installed with the icons on the desktop, disappear when I restart the computer

  Thanks Mike P, I'm sure in the future that all added to the computer is 64-bit application.  Good advice! The problem is almost solved, it seems that the Asus motherboard needed a patch and by some miracle, a Council came through just after the announcement of this complaint.  I turned on the computer this morning, it has pulled up directly on windows without needing a disk of slow start, but it works now!

• Would never be able to stop or restart the computer in the menu after the 10.11.5 update and cannot get the 10.11.6 because iMac restart

  After the 10.11.5 update, that I could never restart or shut down my iMac (late 2013, 3.2 GHz Intel Core i5, 8 GB 1600 MHz DDR3) using the new menu. I can only stop it by pressing the button for a few seconds. I saw a few discussions addressing the question here and have tried to implement some of the solutions proposed, such as restarting in safe mode, deleting the application from Wacom-, but nothing has worked. Now I can't get the 10.11.6 updating or update my Adobe Creative cloud, incidentally, which became available to me, because I can't restart the computer. Do you know if this update would be better and solve the problem? Is there a way I can get this update even if I cannot restart the computer, or even to restore the system to an earlier version?

  Perhaps run EtreCheck and post the results here.

• Since one or two weeks, the docking station settings are not saved. When I restart the computer, the dock is not finished because he was and is located at the bottom and not left

  The parameters of the dock in the system prefs not saved. When I restart the computer, the dock is always located at the same place (bottom) even if I changed before. I have mac os X 11 5 on a mac pro (mid-2010).

  In the case where all third party apps, anti virus are installed, remove them. Click go > hold down the option key and don't release > click library > Preferences find com.apple.dock.plist, com.apple.systempreferences.plist and right click on them and move to the trash.

  The apple logo reboot and empty the trash.

• No automatic updates with the new motherboard. The adjusted settings as advised by your article, restarted the computer - nothing. Downloaded new copy, same problem.

  I get a notification that there is a new update for Firefox and click on it, but the computer is unable to connect to the server and download (if not internet connection works perfectly). I downloaded a new copy and the problem was not solved. I went to your site and set the parameters as indicated by your article, restarted the computer and it is still impossible to have an automatic update as before. (Before the change of the motherboard on the computer of authorized service everything worked fine).

  Try to remove FF from your pc and then it re-download the new version.