restriction password recovery

Similar Questions

• 2821 PASSWORD RECOVERY DISABLED

  Hi all

  I just bought a second hand Cisco 2821. There is a game of password and the password recovery feature is disabled.

  A bit of searching around shows that you can reset the router to the factory default configuration by pressing pause at the right time.

  My problem is that this process does not work. I press pause and get prompt reset factory, I press on 'y', but the router everything continues to load the startup configuration.

  See the output below...

  VERSION of the SOFTWARE system Bootstrap, Version 12.3 (8r) T7 (fc1)

  Technical support: http://www.cisco.com/techsupport

  Copyright (c) 2004 by cisco Systems, Inc.

  The ECC memory initialization

  .

  C2821 processor 262144 KB of main memory

  Main memory is configured for 64-bit with ECC active

  ReadOnly initialized ROMMON

  PASSWORD RECOVERY FEATURE IS DISABLED

  load complete, point of entry to the program: 0x8000f000, size: 0xc5a0

  Initialization of library monitor ATA...

  load complete, point of entry to the program: 0x8000f000, size: 0xc5a0

  Initialization of library monitor ATA...

  load complete, point of entry to the program: 0x8000f000, size: 0x196b438

  Self decompressing the image : ######################################################################################################################################################################################################################################################################################### [OK]

  Smart init is enabled

  Smart init is sizing iomem

  MEMORY_REQ TYPE ID

  0003E8 0X003DA000 C2821 Mainboard

  Swimming pools public buffer 0X000F3BB0

  Swimming pools public particle 0 X 00211000

  TOTAL: 0X006DEBB0

  If all memory conditions above are

  "UNKNOWN", you could use a non supported

  configuration or there is a software problem and

  the system may be compromised.

  Rounded IOMEM to: 8 MB.

  Using 3 percent iomem. [8 mb / 256Mb]

  Legend restricted rights

  Use, duplication, or disclosure by the Government is

  subject to such restrictions as set out in paragraph

  (c) Commercial - limited computer software

  The rights to FAR clause 52.227 - 19 and subparagraph s

  (c) (1) (ii) rights to technical and computer data

  Clause of DFARS 252.227 - 7013 section software.

  Cisco Systems, Inc.

  170 West Tasman Drive

  San Jose, California 95134-1706

  Cisco IOS software, 2800 Software (C2800NM-SPSERVICESK9-M), Version 12.3 (11) T2, RELEASE SOFTWARE (fc1)

  Technical support: http://www.cisco.com/techsupport

  Copyright (c) 1986-2004 by Cisco Systems, Inc.

  Updated Saturday 29 October 04 00:40 by *.

  Image text-base: 0x40073B98 database: 0x424C0000

  <--- i="" press="" break="">

  PASSWORD RECOVERY IS DISABLED.

  You want to reset the default router

  configuration and to proceed [y/n]?<--- i="" press="" "y"="">

  Configuration of the router to factory default reset.

  This product contains cryptographic features and is under the United States

  States and local laws governing the import, export, transfer and

  use. Delivery of Cisco cryptographic products does not imply

  third party approval to import, export, distribute or use encryption.

  Importers, exporters, distributors and users are responsible for

  compliance with U.S. laws and local countries. By using this product you

  agree to comply with the regulations and laws in force. If you are unable

  to satisfy the United States and local laws, return the product.

  A summary of U.S. laws governing Cisco cryptographic products to:

  http://www.Cisco.com/WWL/export/crypto/tool/stqrg.html

  If you need assistance please contact us by mail at

  [email protected] / * /.

  Cisco 2821 (revision 51,46) with 253952K / 8192K bytes of memory.

  Card processor ID FHK0911F1T4

  2 gigabit Ethernet interfaces

  Configuration of DRAM is wide with parity 64-bit capable.

  239K bytes of non-volatile configuration memory.

  62592K bytes of ATA CompactFlash (read/write)

  % WARNING: use 31 mask carefully on the right point to point interface

  % WARNING: use 31 mask carefully on the right point to point interface

  Press RETURN to get started!

  * 19 Nov 02:14: 4110FF58 4110FF9C 410FCAD4 4203EB24 4203EB08

  * 19 Nov 02:14:27.559: % LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed State to

  * 19 Nov 02:14:27.559: % LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed State to

  * November 2012 19 15:14:28.559 NZDT: % LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed State to down

  * November 2012 19 15:14:28.559 NZDT: % LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state down

  * November 2012 19 15:14:28.843 NZDT: % SYS-5-CONFIG_I: configured from the system memory

  * November 2012 19 15:14:29.068 NZDT: % SYS-5-RESTART: System restarted.

  Cisco IOS software, 2800 Software (C2800NM-SPSERVICESK9-M), Version 12.3 (11) T2, RELEASE SOFTWARE (fc1)

  Technical support: http://www.cisco.com/techsupport

  Copyright (c) 1986-2004 by Cisco Systems, Inc.

  Updated Saturday 29 October 04 00:40 by *.

  * November 2012 19 15:14:29.072 NZDT: % SNMP-5-start COLD: SNMP on ROUTER1 host agent knows a cold start

  !       UNAUTHORIZED ACCESS IS STRICTLY PROHIBITED!

  User access audit

  Password:

  Password:

  Password:

  % Of incorrect passwords

  There is a password set and password recovery functionality is disabled.

  The process works because I used it several times.  The reason why it does not work for you is maybe because of the way your client sends the "Ctrl + Break" overall.  It's very obvious when you use a USB-to-serial dongle.

  Another thing, it significantly will help a lot if you first EJECT the CF so the router goes to ROMmon case of your attempts to break failure.

• I forgot my restriction password, let it please help me solve my problem

  I forgot my restriction password, let it please help me solve my problem

  I forgot the password restriction

• Everyone is dismayed to see that there is no password recovery or reset secure put in place for encrypted backups?

  I am absolutely amazed that there is no recovery password for iPhone backups encrypted.

  (1) no password is required to access the iTunes application. He launched and the phone connects automatically.

  (2) someone might maliciously put a password. The password for Mac or device using iTunes OSx need at least before setting the encryption password.

  (3) there is no recovery option. None. Tell me: what password-protected sensitive data have NO option of recovery? No secret questions, no e-mail link, no OSx password, nothing. It's horrible.

  I'm in a situation where I remember not the password, and even if I had the foresight to write it somewhere, that the hard copy has disappeared. I suffer a miserable condition where I lose memory. I have reset passwords on all my stuff course often. That's just my new reality.

  I am faced with a situation where if I ever need to restore my device or upgrade to a new, I won't lose all my old texts and local health data in my applications (which is essential for a person with health problems). The loss of memories of conversations for a person who relies on these devices, precisely because I lose my memory is a slap in the face.

  What the risk of COMPUTER audit team approved this feature, Apple? It's quite incredible that a company of your size would be created people to fail like this. Please post a fix in iTunes for password recovery and substitute it. PLEASE, I BEG YOU.

  N ° if there is a way to recover or reset, the encryption would be completely useless.

  Exercise good security practices on the computer where you have installed iTunes and you will not you care about someone maliciously setting a password for backups.

• I forgot my restriction password

  I forgot my restriction password and I put it where someone could not reset my phone and now I need to reset it to factory settings. Help, please!

  This article:

  Restrictions of use on your iPhone, iPad and iPod touch - Apple Support

  

• Lost administrative password recovery options

  About once a day, I see the same post

  "I lost my administrative password for my computer"

  "I don't remember my password"

  "I need to change the password and I don't remember"

  Without failure, we put the passwords and forget about them and it is not always a simple process to remedy this solution. However, it is a simple process and can easily be avoided. If you read this thread and you have not lost your password to take measures now to protect yourself in case this happens. It will save you time and effort. Always remember, act now to save time tomorrow.

  Retrieve the password using a password reset disk

  This should be your preferred method to reset your password as this is something that you can do and need to do when you settle your account with a password. The password recovery CD must be created before you lost the password to be effective. If you have not already created it and you read this thread to be upward and out with what to do if you are having this issue right now stop and go create this disc.

  Instructions available here

  http://Windows.Microsoft.com/en-us/Windows-Vista/create-a-password-reset-disk

  Now, if you have the drive and you have lost your password it is very simple.

  1 start the computer and try to enter the password on the Windows login screen

  2. the password is incorrect message opens, and from there, you can select ok

  3. once the screen goes away, a new screen appears with an option to reset the password.

  4. follow the instructions on the screen and use the password reset disk to reset your password

  Change your password to a different user account

  If you have multiple user accounts, and at least one of these other accounts have administrator rights, then you can reset your password from the other account. The password of this account may be necessary, then you can check with the owner of the account.

  1. connect to the other account has administrator rights

  2. click the start ORB, then select the Control Panel

  3. from here, select the accounts of users and parental control

  4. Select Manage another account

  5. click on the account with the forgotten password

  6. click on change password

  7. type a new password and press on enter to confirm

  8. click on change password

  9 disconnect you, then try to log on to the original account

  Return to a previous password

  If you have recently changed your password and now can't remember, you can use the application of Microsoft System Restore to return to a time before you changed the password. This would of course imply remind you which has been the case the previous password.

  To go back and use your old password follow these steps:

  1. press on the F11 key repeatedly to open the HP System Recovery program on the system startup

  2. under, I need help immediately, click the Microsoft System Restore option

  3. follow the instructions to restore the computer to a previous state, choose a time before you changed the password.

  Use a third-party program to attempt to reset / recover password

  HP, like most other companies, do not support the use of third-party applications, but they do exist. If you cannot use one of the options mentioned previous then this is may be the option you want to try.

  Removal and recovery of password programs exist and can be found on the internet through various searches on google.

  One of these programs can be found here http://www.pcloginnow.com/ with instructions on how to use it here http://www.pcloginnow.com/guide.html

  Remember that HP mentioned earlier does not support the use of third-party software to retrieve lost passwords, and then you use this tool or any other tool at your own risk.

  Hope this helps you recover your lost password, or you read and warning and make a recovery for you disk protect.

• How can you find your restrictions password if you remember?

  How can you find your restrictions password if you do not remember?

  Read How to reset the forgotten password Restrictions with iPhone restore?

• System user name and password recovery options

  Hi, looking for help to find my user name and password recovery system, I'm trying to factory reset my laptop, any information will be greatly appreciated, thanks siiinky

  Generally, you don't need to insert any user name or password when you start the recovery process...
  Usually, you must press ENTER to continue.

• RNR4000 password recovery (Readynas 1100) failed using the OS install procedure

  I followed the procedure to perform a password recovery by pressing the reset button while you turn on/off the system. Now the NAS is stuck saying "File System Check" in startup RAIDar. RAIDar shows correct, model host name and the IP address has reset to 192.168.168.168. All road lights are green. How can I recover this system now that it does not start? Should I make a boot USB or boot TFTP?

  What version of the firmware?

  Also note that for the 1100, the default password is netgear1 if running RAIDiator 4.x or so in running RAIDiator 3.x it is infrant1

• I forgot my restriction password on my iPad Air and I want to change some settings in this topic, how can I do this but still keep my original content on it?

  I forgot my restriction password on my iPad Air and I want to change some settings in this topic, how can I do this but still keep my original content on it?

  Sorry, but you can't. If you have forgotten your password for the restriction, you must restore the device to a backup made before the restriction code on the device, or restore it as new.

  Sorry,

  GB

• HP MINI 1000: HP MINI 1000 PASSWORD RECOVERY CNU9150CHZ AND CNU9150BRY

  PLS HELP ME CNU9150BRY AND HP MINI 1000 PASSWORD RECOVERY CNU9150CHZ

  CNU9150CHZ = e9lo3q1ez0

  CNU9150BRY = e9lo3q1pbi

  source > https://dl.dropboxusercontent.com/u/26983620/Java_Bios/biosunlock.html

  You can then modify or disable in the bios settings, the bios password if necessary.

• I need your help - account password recovery

  Dear Microsoft,

  I didn't sing in email * E-mail address is removed from the privacy * but I can't the recovery email. Please help me account Password Recovery Ref.

  Account Password Recovery - * address email is removed from the privacy *.

  Last post: TempUser A6E8F21A-E13F-4FE9-87A3-22B322D5184C, Thursday, June 9, 2011 11:39

  Subscribe via RSS

  Thursday, June 9, 2011 11:39

  Utilisateurtemp A6E8F21A-E13F-4FE9-87A3-22B322D5184C

  Thank you

  Saravoot

  Submit all Live and Hotmail queries on the forum right here:

  Windows Live Solution Center
  http://windowslivehelp.com/

• Compaq mini CNU0022G2C: bios password recovery

  Pls I need help my compaq mini password recovery

  Hello

  Enter: e9l1177h7e (3rd character is a lowercase L)

  Kind regards

  DP - K

• Windows Live account password recovery.

  Original title: password recovery.

  If any of you have had or have the same problem as me, could you pls tell me how long

  You need your old p/w which is sent to you via Windows Live. I hope soon. I changed my p/w, one too many times, and he got me in trouble. Now, I can't ' do not forget my p/w. If one of you had the same problem I have at the present time could you pls tell me how long it will take Windows to respond. So, your answers would be very greatly appreciated.

  Hi Marly1956,

  I recommend you post your question in Windows Live Solution Center for assistance.

  Hope the helps of information.

  Concerning
  Joel S
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• ZIP RAR ACE password recovery program

  I found the ZIP RAR ACE password recovery program on my computer. Is it safe? Do I need?

  Hello

  ZIP RAR ACE Password Recovery is a program to recover passwords lost or forgotten files of the following types: ZIP, RAR (including v3.x, v4.x SFX, a work in several volumes and archives with encrypted filenames) and ACE archives.

  If you have installed a publicly traded software then ZIP RAR ACE can help you recover the forgotten password.

  Warning: Using third-party software, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.