Routers Cisco VPN client

Similar Questions

• Using Cisco VPN Client VPN

  Is it possible to use a private network virtual created with the WRVS4400N router with VPN Client from Cisco Systems (ver 5) software? (Although QuickVPN works very well.)

  Is it possible to use with Account customer VPN mode? Or is it possible to use with IPSec VPN (Tunnel) mode? If so, please provide together how to client-side and the router. Thank you!

  Unfortunately Small Business routers are not compatible with the Cisco VPN Clients. The Cisco VPN Clients have more parameters that are not available in the materials of the series of small businesses, so all we can use is the application of QVPN.

• IPSec site to site VPN cisco VPN client routing problem and

  Hello

  I'm really stuck with the configuration of ipsec site to site vpn (hub to spoke, multiple rays) with cisco vpn remote client access to this vpn.

  The problem is with remote access - cisco vpn client access - I can communicate with hub lan - but I need also communication of all lans speaks of the cisco vpn client.

  There are on the shelves, there is no material used cisco - routers DLINK.

  Someone told me that it is possible to use NAT to translate remote access IP-lan-HUB customers and thus allow communication - but I'm unable to set up and operate.

  Can someone help me please?

  Thank you

  Peter

  RAYS - not cisco devices / another provider

  Cisco 1841 HSEC HUB:

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  Group 2

  ISAKMP crypto key x xx address no.-xauth

  !

  the group x crypto isakmp client configuration

  x key

  pool vpnclientpool

  ACL 190

  include-local-lan

  !

  86400 seconds, duration of life crypto ipsec security association

  Crypto ipsec transform-set esp-3des esp-sha-hmac 1cisco

  !

  Crypto-map dynamic dynmap 10

  Set transform-set 1cisco

  !

  card crypto ETH0 client authentication list userauthen

  card crypto isakmp authorization list groupauthor ETH0

  client configuration address card crypto ETH0 answer

  ETH0 1 ipsec-isakmp crypto map

  set peer x

  Set transform-set 1cisco

  PFS group2 Set

  match address 180

  card ETH0 10-isakmp ipsec crypto dynamic dynmap

  !

  !

  interface FastEthernet0/1

  Description $ES_WAN$

  card crypto ETH0

  !

  IP local pool vpnclientpool 192.168.200.100 192.168.200.150

  !

  !

  overload of IP nat inside source list LOCAL interface FastEthernet0/1

  !

  IP access-list extended LOCAL

  deny ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

  deny ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

  IP 192.168.7.0 allow 0.0.0.255 any

  !

  access-list 180 allow ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

  access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

  !

  How the DLINK has been configured for traffic between the site to site VPN subnets? You are able to add multiple remote subnets on DLINK? If you can, then you must add the pool of Client VPN subnet.

  Alternatively, if you cannot add multiple subnet on DLINK router, you can change the pool of Client VPN 192.168.6.0/24, and on the crypto ACL between the site to site VPN, you must edit the 180 existing ACL

  DE:

  access-list 180 allow ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

  access-list 180 allow ip 192.168.200.0 0.0.0.255 192.168.1.0 0.0.0.255

  TO:

  access-list 180 allow ip 192.168.6.0 0.0.1.255 192.168.1.0 0.0.0.255

  Also change the ACL 190 split tunnel:

  DE:

  access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

  access-list 190 allow ip 192.168.1.0 0.0.0.255 192.168.200.0 0.0.0.255

  TO:

  access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.6.0 0.0.0.255

  access-list 190 allow ip 192.168.1.0 0.0.0.255 192.168.6.0 0.0.0.255

  Finally, replace the remote subnet 192.168.7.0/255.255.255.0 192.168.6.0/255.255.254.0 DLINK.

  Hope that helps.

• multi-site VPN with just the cisco vpn client

  Hello everyone

  Please I need your help.

  We have a headquarters office and up to 60 is BranchOffice, we want to create VPN network between its. so let's deploy 2 router cisco esy vpn server with HA (HSRP) at the Headquarters Office and all branches have Connection ADSL and they will use just the cisco vpn client to connect to the Headquarters Office.

  My question is: is it possible to do it just with the client vpn cisco without purchased for any exercise bracnh a cisco router to create an ipsec tunnel because it is so expensive?

  It depends on if the routers to offices can handle NAT with several internal VPN clients to 1 IP address. Most of the new material should be fine. Keep in mind the maximum limit of the VPN client, with 60 agencies and 5 people each of whom you are above the limit.

  Michael

  Please note all useful posts

• Cisco VPN Client causes a blue screen crash on Windows XP Pro (Satellite M30)

  Hello

  I have a Satellite Pro M30 running Windows XP Professional.

  After you start a vpn Tunnel via a customer of Cisco VPN (Version 4.6 and 4.7), the system crashes with a blue screen.

  I see that the key exchange is successful, but immediately after the vpn connection is established Windows XP crashes with a blue screen.

  Someone has any idea how to solve this problem?

  Perhaps by the updated device driver? And if so, which driver should be updated?

  Kind regards

  Thorsten

  Hello

  Well, it seems that the Cisco client is a problem.
  I m unaware of this product because it of not designed by Toshiba.
  I think that the drivers are not compatible with the Windows operating system.
  However, I found this site troubleshooting cisco vpn client:
  Please check this:
  http://www.CITES.uiuc.edu/wireless/trouble-index.html

• Receive message "Validation of C:\WINDOWS\System32\VSINIT.dll failure" error message when trying to run Cisco VPN Client.

  windows\system32\vsinit.dll

  I try to run CISCO "VPN Client" connect from my PC at home for my work PC.

  Then, I get a message:

  Validation failed for C:\WINDOWS\System32\VSINIT.dll

  Any ideas?

  Martin

  Hello

  Run the checker system files on the computer. Link, we can see: Description of Windows XP and Windows Server 2003 System File Checker (Sfc.exe): http://support.microsoft.com/kb/310747

  Note that: if he asks you the service pack CD, follow these steps from the link: you are prompted to insert a Windows XP SP2 CD when you try to run the tool on a Windows XP SP2 computer system File Checker: http://support.microsoft.com/kb/900910 (valid for Service pack 3)

  If the steps above is not enough of it please post your request in the TechNet forum for assistance: http://social.technet.microsoft.com/Forums/en/category/windowsxpitpro

• Professional Windows Vista crashes when you use Cisco VPN Client 5.05.0290

  I have a Dell Latitude E6400 Windows Vista Business (32 bit) operating system. When I go to turn on the VPN client, I get invited to my username / password and once entered, the system just hangs. The only way to answer, it's a re-start. I took action:

  1 disabled UAC in Windows
  2 tried an earlier version of the VPN client
  3. by the representative of Cisco, I put the application runs as an administrator

  If there are any suggestions or similar stories, I would be grateful any offereings.

  It IS the COMODO Firewall with the 5.0.x CISCO VPN client that causes the gel. The last update of COMODO has caused some incompatibility. I tried to install COMODO without the built in Zonealerm, but it is still frozen. The only way to solve it is to uninstall COMODOD. Since then, my CISCO VPN client works again...

• Cisco vpn client minimized in the taskbar and the rest in status: disconnect

  I used 5.0.07.0240 cisco vpn client for 1 month with my pc under windows 7-64 bit. Worked well for 1 month. All of a sudden now when I double click the icon to start, VPN automatically minimizes to the taskbar with the disconnected state. It does not connect the option to hit or anything before it reduced to a minimum. I've not seen this before and no changes... but now it simply doesn't work. All solutions? Windows just patch automatically breaking cisco?
  Unfortunately, cisco does not world class technical service... they called but no use.

  In my view, there is now a published version of the x 64 client, you need to download.
  If you suspect an update of Windows, why not try a system restore for a day, it was
  working correctly?
   
  On Wednesday, April 28, 2010 17:27:46 + 0000, akshay2112 wrote:
   
  > I used 5.0.07.0240 cisco vpn client for 1 month with my pc under windows 7-64 bit. Worked well for 1 month. All of a sudden now when I double click the icon to start, VPN automatically minimizes to the taskbar with the disconnected state. It does not connect the option to hit or anything before it reduced to a minimum. I've not seen this before and no changes... but now it simply doesn't work. All solutions? Windows just patch automatically breaking cisco? Unfortunately, cisco does not world class technical service... they called but no use.
   

  Barb Bowman www.digitalmediaphile.com

• Using Cisco VPN Client in Windows 7 Professional 64 bit

  Hi all!
  I need to use Cisco VPN Client to connect to my server in the company, because my company uses lotus notes Server, I have to connect Cisco VPN to access e-mail. But now my windows version is Windows 7 Pro 64 bits that cannot directly install this application, I already installed XP Mode and creatde shortcut to Windows 7, I plugged the Cisco VPN to my Cisco VPN server, but I can not access the server, Pls help me and show me how to solve this problem

  Open the XP VM itself, do not use the shortcut that was published in
  the W7 boot menu. You need to install Outlook / your email client
  Inside the virtual machine, as well as on the side of W7. You can point to the same
  PST files if you have local PST files, but you just can't open them in
  at the same time of W7 and XP VM.

  There is no way to bridge using the shortcut of publishing app

  Some people have reported success with the third party IPSec
  replacements as customer universal shrew or the NCP. Your IT Department.
  would like to know if these are supported

  :

  > Hello all! I need to use Cisco VPN Client to connect to my server in the company, because my company uses lotus notes Server, I have to connect Cisco VPN to access e-mail. But now my windows version is Windows 7 Pro 64 bits that cannot directly install this application, I already installed XP Mode and creatde shortcut to Windows 7, I plugged the Cisco VPN to my Cisco VPN server, but I can not access the server, Pls help me and show me how to solve this problem
  Barb Bowman www.digitalmediaphile.com

• Cisco VPN Client and 64-Bit OS Support

  I'm in the stages of planning/testing of migrating users to the Cisco VPN client. Problem that I came across well is that I can't find a version that supports 64-bit operating systems. I looked through the Download Center with no luck. I'm a little more looking for a version out there? Thanks in advance.

  As much as I know there is no 64-bit support and is not yet on the roadmap of IPSEC VPN Client. For more details, see:

  http://www.Cisco.com/en/us/docs/security/ASA/compatibility/ASA-VPN-compatibility.html

  Concerning

  Farrukh

• Problems to connect via the Cisco VPN client IPSec of for RV180W small business router

  Hello

  I tried to configure my router Cisco of RV180W as a customer VPN IPSec, but have encountered a problem that I hope someone can help me with. "" I managed to do the work of configuration so that the Cisco's VPN IPSec client authenticates successfully with the XAUTH user, I put on the router, but during the negotiation, the client ends with the following, which appears several times on the router error message: ' Mar 20 Oct 19:41:53 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [34360] has no config mode.

  I've read around the internet and a number of people seem to say that the Cisco VPN Client is not compatible with the router, but the same thing happens to my iPhone VPN client.

  Is it possible that this can be implemented? Below, I have attached the full configuration files and the log files. Thank you much in advance.

  Router log file (I changed the IP addresses > respectively as well as references to MAC addresses)

  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: floating ports NAT - T with counterpart > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] WARNING: notification to ignore INITIAL-CONTACT > [44074] because it is admitted only after the phase 1.
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [4500]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received unknown Vendor ID
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received Vendor ID: CISCO-UNITY
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT detected: is located behind a device. NAT and alsoPeer is behind a NAT device
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: request sending Xauth for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association established for > [4500] -> [44074] with spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REPLY' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: login successful for the user "myusername".
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser connected from the IP >
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: sending of information Exchange: Notify payload [10381]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REQUEST' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: ignored attribute 5
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28683
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28684
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: remove the invalid payload with doi:0.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: purged-Association of ISAKMP security with proto_id = ISAKMP and spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser Logged Out of the IP >
  Mar 20 Oct 20:03:16 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association deleted for > [4500] -> [44074] with spi =>

  The router configuration

  screen_shot_10-20 - 15_at_09.00_pm.png

  

  IKE policy

  screen_shot_10-20 - 15_at_09.00_pm_001.png

  

  screen_shot_10-20 - 15_at_09.01_pm.png

  

  VPN strategy

  screen_shot_10-20 - 15_at_09.02_pm.png

  

  screen_shot_10-20 - 15_at_09.02_pm_001.png

  

  Client configuration

  Hôte : < router="" ip=""> >

  Authentication group name: remote.com

  Password authentication of the Group: mysecretpassword

  Transport: Enable Transparent Tunneling; IPSec over UDP (NAT/PAT)

  Username: myusername

  Password: mypassword

  Please contact Cisco.

  Correct, the RV180 is not compatible with the Cisco VPN Client.  The Iphone uses the Cisco VPN Client.

  You can use the PPTP on the RV180 server to connect a PPTP Client.

  In addition, it RV180 will allow an IPsec connection to third-party customers 3.  Greenbow and Shrew Soft are 2 commonly used clients.

• SafeNet and Cisco VPN Client Compatible?

  I have been using the Cisco VPN for quite awhile with no problems. Recently, we have added a Watchguard Firebox somewhere else and have installed the Client of Watchguard MUVPN, otherwise known as a customer of Safenet.

  Since the installation, I could not yet properly use the Cisco Client. If I disable the two Services of Safenet, I invited to my user id and password and connect to the Cisco Concentrator and get an ip, etc. However, I can't ping anything on the network.

  My solution is to completely uninstall both clients and reinstall the Cisco by itself. This is not very practical.

  If anyone know a fix for this I'd appreciate comments.

  Thank you

  Patrick Dunnigan

  Hi Patrick,

  I only got lucky with the SafeNet customer brand Watchguard with the 4.0.x releases of the Cisco client. I think Cisco 4.6 clients use a newer driver from the DNE or else that plays well with SafeNet.

  In any case, here's how to set up PC that requires both clients:

  First, install the Cisco VPN client. Restart the application, and then stop and disable the Windows service.

  Install the client for Watchguard, reboot as requested.

  Then, stop and set to manual both SafeNet services, then start and set to automatic the Cisco service.

  Delete the shortcut in your Start menu Startup group safecfg.exe (or the key of HKLM\MS\Windows\CurrentVer\Run, where he gets set.)

  Delete the shortcut to start for the Cisco VPN client as well.

  Whenever you want to use the Cisco customer, you can just launch the Dialer to IPSec. If you want to run the SafeNet client, stop the Cisco service, start the services of SafeNet, then run safecfg.exe. A few batch files facilitate this process for users.

  Hope that helps,

  Chris

• AnyConnect + possible PSK (pre-shared key) as under with cisco vpn client ikev1 and ikev2

  Is it possible to create a VPN Anyconnect of RA with just the name of user and password + pre-shared key (Group) for the connection, as could do for ikev1 with cisco VPN client? I am running 8.4.X ASA code and looks like tunnel-group commands have 8.2.X somewhat change. If you change the group type of the tunnel for remote access, now there is no option for IKEv2 PSK. This is only available when you choose the type

  Type of TG_TEST FW1 (config) # tunnel - group?

  set up the mode commands/options:
  Site IPSec IPSec-l2l group
  Remote access using IPSec-IPSec-ra (DEPRECATED) group
  remote access remote access (IPSec and WebVPN) group
  WebVPN WebVPN Group (DEPRECATED)

  FW1(config-tunnel-General) # tunnel - group TG_TEST ipsec-attributes
  FW1(config-tunnel-IPSec) #?

  configuration of the tunnel-group commands:
  any required authorization request users to allow successfully in order to
  Connect (DEPRECATED)
  Allow chain issuing of the certificate
  output attribute tunnel-group IPSec configuration
  mode
  help help for group orders of tunnel configuration
  IKEv1 configure IKEv1
  ISAKMP policy configure ISAKMP
  not to remove a pair of attribute value
  by the peer-id-validate Validate identity of the peer using the peer
  certificate
  negotiation to Enable password update in RADIUS RADIUS with expiry
  authentication (DEPRECATED)

  FW1(config-tunnel-IPSec) # ikev1?

  the tunnel-group-ipsec mode commands/options:
  pre-shared key associate a key shared in advance with the connection policy

  I'm getting old so I hope that it is not in another complaint curmudgeonly on the loss of functionality. :)

  Many small businesses do not want to invest in the PKI. It is usually a pain to deploy, backup, make redundant, etc..

  But it would be nice to have a bit more security on VPN other than just the connections of username and password.

  If this is not possible, it is possible to configure the Anyconnect customer to IKEv1 with PSK and name at the level of the Group client?

  If this is not possible, WTH did cisco end customer VPN cisco as a choice of VPN connection (other than to get more fresh mail of license)?

  I really hope that something like this exists still!

  THX,

  WR

  You are welcome

  In addition to two factors, you can also do double authentication (ie the two using the user name and password). Each set of credentials can come from a Bank of different identities.

  With this scheme, you can can configure a local user name (common) with password on the SAA (think of it as your analog PSK) and the other be the AD user identification information.

• CISCO ANYCONNECT VPN CISCO VPN CLIENT

  Hi, I was in the process of configuring cisco anyconnect vpn for ip phones to our local obtained the license for them either, the question that I get is that I already have remote configured cisco connect via the old cisco vpn client.

  now, if I activate the anyconnect ssl on the same outside the interface both can exist without conflict or maybe I need to migrate users to install the end customer for anyconnect system software to connect.

  I also need help with authentication of certification.

  concerning

  You can run both VPN at the same time without problems.

  However, you should try and migrate everyone to the latest technology Anyconnect SSL anyway.

• Compression &amp; CISCO VPN Client

  Hello

  I'm trying to understand if the compression is available using a 5.x CISCO VPN client to a device of CISCO (ASA, 871 etc..)

  Our site has recently moved from dial-in Windows, where compression is enabled, and we noticed the CISCO client show 'no compression '.

  Thank you

  Mario

  This URL describes how to configure the compression on the SAA.

  http://www.Cisco.com/en/us/docs/security/vpn_client/cisco_vpn_client/vpn_client500_501/administration/5vcAch3.html

  Compression can be configured as a parameter within the crypto ipsec transport-set in the IOS.

  http://www.Cisco.com/en/us/customer/docs/iOS/Security/command/reference/sec_c3.html#wp1057372

  Compression/decompression takes a toll hitting on the resources of the Cisco device if it lacks a hardware dedicated for these functions. You may want to limit its use to only where this is necessary for the remote access clients.

  HTH