RUNDLL error gray box

Similar Questions

• rundll error loading c:\WINDOWS\pbl32rtU.dll start box

  Hello

  Can someone help me.  I started my netbook this morning and managed to catch the virus spcmdcom.sys.  Finally after I started my netbook in safe mode, I was able to run the latest malwarebytes and who seems to have got rid of however I none get a RUNDLL don't box start with the message error loading c:\WINDOWS\pbl32rtU.dll and I can not connect to all web pages - although I can connect to a Web page via Fillezilla I host - go figure.

  In any case please please please can someone give me advice on what I should do.

  I can't connect to the internet to run a registry fix :(

  Any help appreciated with gratitude

  Hello

  This is the result of malware then carry out a very thorough check and when the system
  is clean see the following message to remove these errors.

  If you need search malware here's my recommendations - they will allow you to
  scrutiny and the withdrawal without ending up with a load of spyware programs running
  resident who can cause as many questions as the malware and may be more difficult to detect as the
  cause.

  No one program cannot be used to detect and remove any malware. Added that often easy
  to detect malicious software often comes with a much harder to detect and remove the payload. Then
  its best to be thorough than paying the high price later now too. Check with them to one
  extreme overkill point and then run the cleaning only when you are sure that the system is clean.

  It can be made repeatedly in Mode safe - F8 tap that you start, however, you must also run
  the regular windows when you can.

  Download malwarebytes and scan with it, run MRT and add Prevx to be sure that he is gone.
  (If Rootkits run UnHackMe)

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN

  Malwarebytes - free
  http://www.Malwarebytes.org/

  Run the malware removal tool from Microsoft

  Start - type in the search box-> find MRT top - right on - click RUN AS ADMIN.

  You should get this tool and its updates via Windows updates - if necessary, you can
  Download it here.

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN
  (Then run MRT as shown above.)

  Microsoft Malicious - 32-bit removal tool
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=AD724AE0-E72D-4F54-9AB3-75B8EB148356&displaylang=en

  Microsoft Malicious removal tool - 64 bit
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=585D2BDE-367F-495e-94E7-6349F4EFFC74&displaylang=en

  also install Prevx to be sure that it is all gone.

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN

  Prevx - Home - free - small, fast, exceptional CLOUD protection, working with others
  security programs. It is a single scanner, VERY EFFICIENT, if it finds something to come back
  here or use Google to see how to remove.
  http://www.prevx.com/   <-->
  http://info.prevx.com/downloadcsi.asp  <-->

  Choice of PCmag editor - Prevx-
  http://www.PCMag.com/Article2/0, 2817,2346862,00.asp

  Try the demo version of Hitman Pro:

  Hitman Pro is a second scanner reviews, designed to save your computer from malicious software
  (viruses, Trojans, rootkits, etc.). who infected your computer despite safe
  what you have done (such as antivirus, firewall, etc.).
  http://www.SurfRight.nl/en/hitmanpro

  --------------------------------------------------------

  If necessary here are some free online scanners to help the

  http://www.eset.com/onlinescan/

  New Vista and Windows 7 version
  http://OneCare.live.com/site/en-us/Center/whatsnew.htm

  Original version
  http://OneCare.live.com/site/en-us/default.htm

  http://www.Kaspersky.com/virusscanner

  Other tests free online
  http://www.Google.com/search?hl=en&source=HP&q=antivirus+free+online+scan&AQ=f&OQ=&AQI=G1

  --------------------------------------------------------

  Also follow these steps for the General corruption of cleaning and repair/replace damaged/missing
  system files.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
  RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker
  (SFC.exe) program generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Run checkdisk - schedule it to run at the next startup, then apply OK then restart your way.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -----------------------------------------------------------------------

  If we find Rootkits use this thread and other suggestions. (Run UnHackMe)

  http://social.answers.Microsoft.com/forums/en-us/InternetExplorer/thread/a8f665f0-C793-441A-a5b9-54b7e1e7a5a4/

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• When I restart the computer, I get 2 boxes of RunDLL error appearing

  Hi guys,.

  When I restart the computer, I get 2 RunDLL error boxes that appear.  They do not seem to affect the performance of the computer, but they must mean something.  If I need, where can I get the new?

  Descriptions of the errors are...

  RunDLL
  THERE WAS A PROBLEM STARTING
  C:\USERS\ROSS\APPDATA\ROAMING\C_28595R.dll
  THE SPECIFIED MODULE COULD NOT BE FOUND

  RunDLL
  THERE WAS A PROBLEM STARTING
  C:\USERS\ROSS\APPDATA\ROAMING\pegibbfcm.dll
  C:\USERS\ROSS\APPDATA\ROAMING\pegibbfcm.dll IS NOT a VALID WIN32 APPLICATION

  I am running Windows 7 and my last update was KB2709981

  Thank you

  Ross_911

  Hello.

  Click on this link: http://www.scanwith.com/Autoruns_download.htm download & install it. (It is a secure reliable software). You can keep it for future use if you choose.
  1. after the download is complete, select autoruns & right click on it
  2. click on "extract here".
  3. on the extracted files, click "autoruns" application select it & right click and click"Open or run"& click OK or Yes if the process of ptompted by an administrator to complete the installation.
  4. what which is complete, Open or run "autoruns".
  5. in the opened window, click 'all'.
  6. on all programs that says 'file not found' select each & every one of them, click on one at a time...
  7 right-click & click delete & ok

  He helped?

• Windows XP starts, an error message appears. 'RUNDLL error loading C:\Windows\ihukuqej.dll'. The module specific cound not be found.

  Original title: Windows Rundll error on startup

  My laptop, Windows XP startup, an error message appears. RUNDLL error loading C:\Windows\ihukuqej.dll.  The module specific cound not be found.  I downloaded ParetoLogic PC Health, did a full scan on the registry and fixed all of them, rebooted and its still there.

  What is a rundll error?

  File rundll.exe are processes systems directly connected to your computer Windows registry. All of the Dll files are a part of the vast library that contains code and data that are shared by many programs. This allows to obtain the effectiveness of speed and memory of your operating system by reusing the same code or file to run many functions of various programs. An error occurs when the program are not allowed to access this code.

  Why do you Rundll errors?

  Windows uses rundll files to load programs, files, and applications. If the dll file is missing or damaged, any application using this file cannot be loaded. This will produce a rundll error. The reason why the file has disappeared is often related to a virus or spyware. This type of malware often tries to divert the files shared by the rundll file. Other sharing programs file then do not work effectively or to load any.

  STEP 1: IDENTIFY

  The first thing you need to do is to identify the process specific rundll. This isn't a difficult task; There is a library online extensive process in which you can assess the validity of the process that is running. When the error dialog box opens, it displays the name of the process. For example, if the dialog box appears and tells you the dll error:

  STEP 2: STOP THE PROCESS

  Often, you can locate the Dll of enforcement in the services of the exe. You can open your services configuration by following the instructions below:
  1. open your Start menu.
  2. click on run
  3. in the command screen type:services.msc
  4. This will bring to the top of the window Management of the Services . If you drag the mouse to one of the services. It will give you a detailed explanation of the service in question. By right-clicking the individual service.
  5.stop the "dll" service immediately.

  NOTE: sometimes the dll process can not be stopped by this method.

  

  STEP 3: CHECK FOR AND REMOVE

  You need to open your Windows registry file system. It is an extremely delicate process. The registry key: HKEY_LOCAL_MACHINE > SOFTWARE > Microsoft > Windows > CurrentVersion > RUN

  This action will help you speed up the considerable load time of your applications. Here's how:

  1. click on Start
  2. click on run
  3. type regedit
  4. find this registry key:
  HKEY_LOCAL_MACHINE > SOFTWARE > Microsoft > Windows > CurrentVersion > RUN

  5. in the right section click on: "rusvdgpo" = "%System%undll32.exe % System%usvdgpo.dll, [RANDOM LETTERS].
  6. delete the value and reboot.

  

  SPECIAL REMARKS

  Rundll.exe is a critical system process. However, there a great vulnerability is back, which makes it more prone to malicious purposes by an attacker allowing access to your computer from remote locations, stealing passwords, personal data and Internet banking.

  The Trojans are usually use this attack method to share a process that invites the other malware be more Trojan horses or other forms of spyware. The best defense is to keep your security up-to-date software and explain the process of rundll on your computer.

  ======================

  More information is a lot to explain and resolve the problem.

  Since it is a painful process for beginners, it is best to create a new user account and remove the error causing the user account.

  Because not only it solves problems, there will be new user settings and the program files needed for the user account.

  Once you are in the new user account, you can scan by using a program that synchronize with the server and check for virus/malware/spyware.

  Here is the link.

  Run hitman pro 3.5

  http://www.SurfRight.nl/en/downloads

• How to fix Rundll errors at startup caused by WildTangent

  Hope you can help me with this.  I use XP and whenever I start my computer, I get a message that says WildTangent Rundll error module is not found.  This gets really annoying...  I tried using msconfig and uncheck the box that I thought was the cause of the problem.  The message has disappeared, but the computer obviously wasn't working properly after that.  Anyone has any ideas on other things I can do.  I did a system restore and the message reappeared.

  Hello

  I followed your instructions exactly and has competed only auturuns scan.  I unchecked the box that mentioned Wild Tangent, and when I restarted my computer, the message didn't come.  Thanks to you, it seems that the problem is solved, finally.  I can't thank you enough.  I really think you need to be a genius!

  Thanks again.

  Sincerely,

  Joanne

• I have a Dell computer that came with Windows XP Home edition. When I start my computer the monitoring of ERROR appears: RUNDLL error loading \3\DLBUtime.dll

  Error loading \3\DLBUtime.dll

  I have a Dell computer that came with Windows XP Home edition.  When I start my computer the monitoring of ERROR appears: RUNDLL error loading specified not found \3\DLBUtime.dll module

  I just click 'ok' and he goes, but, as for what it stop popping up everytime I start my computer.

  Can someone help me with this?

  Aprilm,

  You are LuLu5119, who posted a question last August?

  If this isn't the case, you should have started your own thread.  If so (and even if not), you should have responded to questions about Dell printers.

  Assuming that you complain of a "Error loading \3\DLBUtime.dll" message that appears when you start your computer, you should know that the DLBUtime.dll file probably has something to do with the software from Dell which has been partially deleted, but could also be indicative of malware as well as partially withdrawn.

  In both cases, the best way for start you to prevent the message at windows is to download Autoruns http://technet.microsoft.com/en-us/sysinternals/bb963902.aspx

  Install the Autoruns and let it complete the scan of your computer.  Then click on the "Connection" tab and uncheck the following entry:

  Look for an entry that has 'DLBUCATS' in the first column.  If you do not see that, look for "rundll32 \3\dlbutime.dll" in the last column ("path of the Image).

  Uncheck that entry, close Autoruns and restart your computer.  You should get is no longer the message.

  If for any reason, you find later that you need dlbutime.dll running, run Autoruns and check the box. If you decide that you need never again, run Autoruns, right-click on the entry and select Delete.

  As General precautionary measure, in case your entry dlbutime.dll was related to malicious software, rather than the Dell printing software, download the following free scanners:

  MalwareBytes Anti-Malware: http://malwarebytes.org/
  SUPERAntiSpyware Portable: http://superantispyware.com/portablescanner.html

  For MalwareBytes Anti-Malware, download, install, update and run.
  For Portable SAS, follow the instructions on the Web page (note that the instructions assume that you use a different computer to download; if you're not, just make a note of the name of the file).

• «RUNDLL error loading the C:\...» "at startup

  Start Up and as I get load of icons on the desktop: "RUNDLL error loading C:\Documents and Settings\Ralph\Local Settings\Application Data\compatCommsdlg\uniMainTask.dll the specified module is not found."

  I have XP SP3.  I understand that vaguely that a dll file has something to do with an application.  All programs loading and I seem to be able to use all the programs but I must first click 'OK' to the message acknowledgew to continue.  (1) what is the error?  (2) what program he claims? ((3) how do necessary file or, if not necessary, 4) how can I get rid of the error?

  Looking for errors like this by doing a search on Google for the name of the file.  Usually, they turn up without success.

  When a search in no hits or suspicious hits result, the answer is usually that the file in question is linked to the malicious software and your anti-malware application has deleted or quarantined file, but left to the Windows registry entry that tries to start the malicious software when you start your computer.

  In your case, there is no success for uniMainTask.dll, but the file name is not typical of the random letters used for malware, so it may indeed be a legitimate application-related.  However, you should treat it similarly.

  First of all, download, install, update and run full scans with two of these free analytical tools:

  MalwareBytes AntiMalware
  SUPERAntiSpyware

  Do not run the scans at the same time.  They can take some time, so start an and then go for a non computer chore for awhile.

  If the scans does not solve the problem (and they can't, because the actual malware file has already been processed), then download and run Autoruns.  Click on the "Connection" tab and look in the column 'Image path' for the dll named in your error message.  If it is not displayed in the connection tab, click the "all" tab and use the file > search tool.  A characteristic of the search of Autoruns tool is that you must move the selection under the element line "found" before you "Find Next."

  Once you find the line with the file in question, either "delete" or (if you want to be safer) uncheck the box.  The latter prevents the line running, but you can reactivate it later by removing the check mark.

  Look at the line Autoruns including uniMainTask.dll of clues about what application it can relate to. If it relates to a legitimate request, you may need to reinstall this application.

• RUNDLL error loading c:\windows\icstlt2.dll the specified module could not be found

  This happens every time I start my computer. I can't do anything with the computer until I click the OK box. Then everything is generally well, but sometimes the computer just hangs. What is this and how do I get rid of him?

  It's just a dll name random belonging to some malware that had removed your antivirus programs or security.

  The error is because the point of loading in the registry is still present and it is trying to load the module that no longer exist where the "load error".

  You can uncheck the corresponding item in msconfig > startup, or if you scan from HijackThis, you can run it and difficulty of the relevant start pointing to icstlt2.dllentry.

  Similar to the example of an entry from Hijackthis below.
  "Rundll error loading c:\windows\ksexyn.dll. The specified module could not be found.

  Fixing the entry in HijackThis stopped at the error.
  O4 - HKCU\... \Run: [Pzemowukatiy] rundll32.exe "C:\WINDOWS\ksexyn.dll",Startup"
  http://free.antivirus.com/HijackThis/

  Let us know if you need more assistance.

• Unable to access speech Control Panel. RUNDLL error message: an exception has occurred

  Error text box appear when I try to click speech under control panel.

  RUNDLL: an exception has occurred trying to run"C:\WINDOWS\system32\shell32.dll,Control_RunDLL"C:\Program Files\Commoon Files\Microsoft Shared\Speech\sapi.cpl,Speech"

  What should I do to fix this?

  Hi CSFUN,
   
  -Remember to make changes to your computer after that this problem started to happen?
   

  Follow the steps listed in the article below and check if the problem is resolved.

  Cannot find the Rundll32.exe file when you open Control Panel

• Start windows XP Home Edition with a RunDLL error

  When I boot windows XP Home, after the Welcome screen and the office fills with icons, I have a RunDLL error box that says the right: error loading c:\windows\dlioneg.dll the specified module could not be found. I ran RegistryBooster2010 but it did not help.  Any idea.  The computer is a small netbook from ASUS.

  This file was probably part of a virus or spyware infection that has been partially removed. Run a full scan for virus/spyware.  If the problem persists, use the free Windows Sysinternals Autoruns tool to find and remove the reference to the file.

  For more information about how to use the Autoruns, please see:

  Autoruns for Windows Windows Sysinternals Autoruns Forum

  Boulder computer Maven
  Most Microsoft Valuable Professional

• RUNDLL error is displayed at the start of each time.

  When I start, this message appears in a small window, I usually just close it, but I want to get rid of it and find out if there is no danger. The message is:

  RUNDLL error loading C:\PROGRA~1\3721\helper.dll the specified module could not be found.

  I looked on the internet but I can't find any solution. I havn't made the latest changes to my laptop.

  System information:

  Microsoft Windows XP Professional Version 2002 Service Pack 2

  Please, any help would be greatly appreciated.

  Thank you

  http://www.pcreview.co.uk/forums/thread-428084.php

  Helper.dll and the specific load error are associated with
  spy | Adware. Better to download and install AdAware and Spybot.
  Activate files and hidden folders and then scan the system to remove the
  parasites.

  Read the info above about helper.dll by mow green MVP...

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  You could have, or still are, infected by malware; and it could also be a starting top left him entry.

  Malware scan:

  http://www.Malwarebytes.org/MBAM.php

  Malwarebytes is as its name suggests, a Malware Remover!

  Download the free Version from the link above.

  Download, install, upgrade and scan once a fortnight...

   

  How to use Malwarebytes once it is installed and updated:

  1. open Malwarebytes > click the update tab at the top > get the latest updates.

  2. on the Scanner tab, make sure that thePerform full scan option is selected and then click on theScan button to start scanning your computer

  3 MBAM will now start to scan your computer for malware. This process can take some time.

  4. when the scan is complete, a message box will appear

  5. you must click on the OK button to close the message box and continue the process of Malwareremoval.

  6. you will now be at the main scanner screen. At this point, you must click on the button toview the result .

  7. a screen showing all of the malware displayed the program that is

  8. you must now click remove selection button to remove all the listed malware. MBAM will now delete all of the files and registry keys and add them to the programs quarantine. When you remove files, MBAM may require a restart in order to eliminate some of them. If it displays a message stating that it needs to restart, please let him do. Once your computer has rebooted, and logged in, please continue with the remaining steps.

  9. when MBAM has finished remove the malware, it will open the scan log and display it in Notepad. See the log as desired, and then close the Notepad window.

  10. you can now exit the MBAM program.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  If the error persists after scanning, use the program to out startup:

  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx

  This utility, which has a knowledge of auto-starting locations of any startup monitor, shows you what programs configured to run at system startup or login and that the entries in the order of processing windows. These programs include those in your startup folder, Run, RunOnce, and other registry keys. You can configureAutoruns to show other locations, including Explorer shell, toolbar extensions, helper objects to the browser, Winlogon notifications, auto and many start-up services even more. Autoruns goes way beyond the MSConfig utility bundled with Windows Me and XP.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  XP forums:

  http://social.answers.Microsoft.com/forums/en-us/category/WindowsXP

  Link above is for XP Forums.

  There is a list of the different Forums XP to the link above to help you.

  You get the help you need there.

  Here is the Vista Forums.

  See you soon

  Mick Murphy - Microsoft partner

• When I start my computer windows vista, there is always a pop ups saying that RunDLL error loading C;\users\user\AppData\Roaming\nmhciu.dll

  When I start my computer windows vista, there is always a pop ups box indicating
  RunDLL
  Error loading C;\users\user\AppData\Roaming\nmhciu.dll
  C;\users\user\AppData\Roaming\nmhciu.dll is not a win32 application

  Hi M.A.Rawat,

  ·         Did you do changes on the computer before the show?

  I suggest you to check and clean the boot if the problem persists.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

   

  Note: After troubleshooting, be sure to configure the computer to start as usual as mentioned in step 7 in the above article.

  I hope this helps.

• RUNDLL error loading C:\progra~2\myweb~1\bar\1.bin\F3SCRCTR.dll

  RUNDLL error loading C:\progra~2\myweb~1\bar\1.bin\F3SCRCTR.dll

  Hello

  You really don't want MyWebSearch toolbar as it has malware that are associated with him.

  M3PLUGIN. DLL, information
  http://www.bleepingcomputer.com/startups/m3plugin.dll-23933.html

  How to get rid of the Mywebsearch toolbar
  http://www.ehow.com/how_4780067_rid-MyWebSearch-toolbar.html

  Products Fun Web "My Web search" removal Instructions and help
  http://www.pchell.com/support/MyWebSearch.shtml

  -------------------------------------------------------------

  To ensure that his party and IE and system are clean:

  IE - Tools - Internet Options - Advanced - tab click on restore, and then click Reset - apply / OK

  IE - Tools - Internet Options - Security tab - click on reset all default areas - apply / OK

  Close and restart IE

  IE - tools - manage Addons (for sure disable SSV2 if it is there, it is no longer necessary but Java always install
  "(and it causes problems - you never update Java to go back in and turn it off again)." Search for other possible problems.

  Windows Defender - tools - software explore - look for problems with programs that do not look right. Permit
  are usually OK and "unauthorized" are not always bad. If in doubt about a program to ask about it here.

  Could be a free - SpyBHOremover - BHO - standalone program, needs no installation, download and run - not
  all of them are bad, but some can cause your question (toolbars are BHO).
  http://securityxploded.com/bhoremover.php

  Startup programs
  http://www.Vistax64.com/tutorials/79612-startup-programs-enable-disable.html

  Also get Malwarebytes - free - use as scanner only.

  Malwarebytes - free
  http://www.Malwarebytes.org/products/malwarebytes_free

  SuperAntiSpyware Portable Scanner - free
  http://www.SUPERAntiSpyware.com/portablescanner.HTML?tag=SAS_HOMEPAGE

  Run the malware removal tool from Microsoft

  Start - type in the search box-> find MRT top - right on - click RUN AS ADMIN.

  You should get this tool and its updates via Windows Update - if necessary, you can download it here.

  Download - SAVE - go where go out you there - top - right click RUN AS ADMIN
  (Then run MRT as shown above.)

  Microsoft Malicious - 32-bit removal tool
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=AD724AE0-E72D-4F54-9AB3-75B8EB148356&displaylang=en

  Microsoft Malicious removal tool - 64 bit
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=585D2BDE-367F-495e-94E7-6349F4EFFC74&displaylang=en

  also install Prevx

  Prevx - Home - free - small, fast, exceptional CLOUD protection, working with others
  security programs. It is a single scanner, VERY EFFICIENT, if it finds something to come back
  here or use Google to see how to remove.
  http://www.prevx.com/   <-->
  http://info.prevx.com/downloadcsi.asp?prevx=Y  <-->

  Choice of PCmag editor - Prevx-
  http://www.PCMag.com/Article2/0, 2817,2346862,00.asp

  Try the demo version of Hitman Pro:

  Hitman Pro is a second scanner reviews, designed to save your computer from malicious software
  (viruses, Trojans, rootkits, etc.). who infected your computer despite safe
  what you have done (such as antivirus, firewall, etc.).
  http://www.SurfRight.nl/en/hitmanpro

  --------------------------------------------------------

  If necessary here are some free online scanners to help the

  http://www.eset.com/onlinescan/

  -----------------------------------

  Original version is now replaced by the Microsoft Safety Scanner
  http://OneCare.live.com/site/en-us/default.htm

  Microsoft safety scanner
  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  ----------------------------------

  http://www.Kaspersky.com/virusscanner

  Other tests free online
  http://www.Google.com/search?hl=en&source=HP&q=antivirus+free+online+scan&AQ=f&OQ=&AQI=G1

  --------------------------------------------------------

  Try these to erase corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  --------------------

  Departure - in the search box, type-> order

  at the top of the list to find COMMAND - CLICK RIGHT to it - RUN AS ADMIN

  Type the following commands (or copy and paste one at a time), each followed by pressing on enter.

  ipconfig/flushdns

  nbtstat-r

  nbtstat - RR

  netsh int Reinitialis

  netsh int ip reset

  netsh winsock reset

  RESET

  That resets your TCP/IP stack

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• RUNDLL ERROR in c:\windows\dclonih.dll

  On startup, I get a RUNDLL error. The file is c:\windows\dclonih.dll

  It is either missing or messed up... How should I do?

  Hello

  Cannot find this file on Google so you probably dodged some software malware and you should do a
  very thorough control. Message on how to remove the error message if still it y
  After the audits of malware.

  No one program cannot be used to detect and remove any malware. Added that often
  easy to detect malicious software often comes with a much harder to detect and remove the
  payload. So its best to be now too thorough than paying the high price later. Check
  with an extreme overdose point and then run the cleaning only when you are very
  that the system is clean.

  It can be made repeatedly in Mode safe - F8 tap you start, however, you should
  also run in regular Windows when you can.

  Download malwarebytes and scan with it, run MRT and add Prevx to be sure that he is gone.
  (If Rootkits run UnHackMe)

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN

  Malwarebytes - free
  http://www.Malwarebytes.org/

  Run the malware removal tool from Microsoft

  Start - type in the search box-> find MRT top - right on - click RUN AS ADMIN.

  You should get this tool and its updates via Windows updates - if necessary, you can
  Download it here.

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN
  (Then run MRT as shown above.)

  Microsoft Malicious - 32-bit removal tool
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=AD724AE0-E72D-4F54-9AB3-75B8EB148356&displaylang=en

  Microsoft Malicious removal tool - 64 bit
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=585D2BDE-367F-495e-94E7-6349F4EFFC74&displaylang=en

  also install Prevx to be sure that it is all gone.

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN

  Prevx - Home - free - small, fast, exceptional CLOUD protection, working with the other security
  programs. It is a single scanner, VERY EFFICIENT, if it finds something come back here or
  Use Google to see how to remove.
  http://www.prevx.com/   <-->
  http://info.prevx.com/downloadcsi.asp  <-->

  Choice of PCmag editor - Prevx-
  http://www.PCMag.com/Article2/0, 2817,2346862,00.asp

  Try the demo version of Hitman Pro:

  Hitman Pro is a second scanner reviews, designed to save your computer from malicious software
  (viruses, Trojans, rootkits, etc.). who infected your computer despite safe
  what you have done (such as antivirus, firewall, etc.).
  http://www.SurfRight.nl/en/hitmanpro

  --------------------------------------------------------

  If necessary here are some free online scanners to help the

  http://www.eset.com/onlinescan/

  New Vista and Windows 7 version
  http://OneCare.live.com/site/en-us/Center/whatsnew.htm

  Original version
  http://OneCare.live.com/site/en-us/default.htm

  http://www.Kaspersky.com/virusscanner

  Other tests free online
  http://www.Google.com/search?hl=en&source=HP&q=antivirus+free+online+scan&AQ=f&OQ=&AQI=G1

  --------------------------------------------------------

  Also follow these steps for the General corruption of cleaning and repair/replace damaged/missing system
  files.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
  RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker
  (SFC.exe) program generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Run checkdisk - schedule it to run at the next startup, then apply OK your way out then
  turn it back on.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -----------------------------------------------------------------------

  If we find Rootkits use this thread and other suggestions. (Run UnHackMe)

  http://social.answers.Microsoft.com/forums/en-us/InternetExplorer/thread/a8f665f0-C793-441A-a5b9-54b7e1e7a5a4/

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• RUNDLL error missing dec3271.dll

  original title: rundll error

  I get an error message that reads
  RUNDLL error
  Error loading C:\Users\Owner\AppData\Local\dec3271.dll
  Specified module could not be found

  What can I do about it?

  You could have, or still are, infected by malware; and it could also be a starting top left him entry.

  Malware scan:

  http://www.Malwarebytes.org/MBAM.php

  Malwarebytes is as its name suggests, a Malware Remover!

  Download the free Version from the link above.

  Download, install, upgrade and scan once a fortnight...

   

  How to use Malwarebytes once it is installed and updated:

  1. open Malwarebytes > click the update tab at the top > get the latest updates.

  2. on the Scanner tab, make sure that thePerform full scan option is selected and then click on theScan button to start scanning your computer

  3 MBAM will now start to scan your computer for malware. This process can take some time.

  4. when the scan is complete, a message box will appear

  5. you must click on the OK button to close the message box and continue the process of Malwareremoval.

  6. you will now be at the main scanner screen. At this point, you must click on the button toview the result .

  7. a screen showing all of the malware displayed the program that is

  8. you must now click remove selection button to remove all the listed malware. MBAM will now delete all of the files and registry keys and add them to the programs quarantine. When you remove files, MBAM may require a restart in order to eliminate some of them. If it displays a message stating that it needs to restart, please let him do. Once your computer has rebooted, and logged in, please continue with the remaining steps.

  9. when MBAM has finished remove the malware, it will open the scan log and display it in Notepad. See the log as desired, and then close the Notepad window.

  10. you can now exit the MBAM program.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  If the error persists after scanning, use the program to out startup:

  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx

  This utility, which has a knowledge of auto-starting locations of any startup monitor, shows you what programs configured to run at system startup or login and that the entries in the order of processing windows. These programs include those in your startup folder, Run, RunOnce, and other registry keys. You can configureAutoruns to show other locations, including Explorer shell, toolbar extensions, helper objects to the browser, Winlogon notifications, auto and many start-up services even more. Autoruns goes way beyond the MSConfig utility bundled with Windows Me and XP.

  See you soon.

  Mick Murphy - Microsoft partner