Rv016

Similar Questions

• Path of evolution for Linksys RV016 router

  I have a series of simple questions.

  KNOWN: Bought a router Linksys RV016 sale of diocese and it works without a problem

  Firmware version: 1.3.2

  UNKNOWN: How to get the following:

  1. 1.3.4 update firmware
  2. Firmware firmware 2.0.0 with the bootstrapper process to move to the version 2 series
  3. Firmware versions in the 2.0.0 beta/release series to get the final 2.0.0 beta/release

  From what I read, I must go to the 2.0.0 for later through the 2.0 series before I can move to the 3.0.x series.

  All links come from FTP dead Linksys and the most recent ftp sources series 3.0 last only Cisco, which is absolutely useless to someone in my situation.

  Your help would be much appreciated.

  I have 20 years in the industry so I just need the files of the firmware to get this current router.

  Sincerely,

  Marc J. Driftmeyer

  Hello and welcome to the community at the homepage of Cisco!

  This product is managed by the Cisco Small Business Support Community.

  For future discussions about this product, go here.

• Connect the 2 locations using RV016 router to fill 2 different networks.

  I have a RV016 connected to a comcast cable modem to slot 1 with IP 192.168.6.1

  I have a RV016 connected to a comcast cable modem at the 2 with 192.168.10.1 IP location

  I installed a VPN tunnel from gateway to gateway between 2 routers RV016.

  I have a LAN in slot 1 with the IP 192.168.1.1, which connects to the internet through an Adtran router with 4 lines of T1 servile.

  I have a LAN with IP 192.168.5.1 2 location that connects to the internet through an Adtran router with 3 T1 lines servile.

  I like a computer to location 2 to connect to the RV016 in the local Comcast modem to the Comcast modem at location 1 in the RV016 to slot 1 then go out to the local network at location 1 and communicate with an application server on LAN 1.

  Help, please.

  You can't do that with a RV016. The RV016 only supports layer 3 tunnel. This means that the two ends are different networks with different subnets. The traffic between them is not filled.

  If you want to really two bridged networks, i.e. join in a single LAN with a single IP subnet and a single broadcast domain you need a layer 2 tunnel, for example a tunnel L2TPv3. That works on layer 2, which is on the MAC addresses inside your networks. In this way, you can use the same IP subnet at both ends and on each side, it seems that the other side is connected to the same ethernet network.

  The RV016 does not support the tunneling of layer 2. You can create an IPSec tunnel, which is layer 3. If there is really a need for a tunnel layer 2, you get different devices. I recommend that you evaluate if a layer 2 connection is really necessary or not.

• Linksys RV016 and two WAN (ADSL + cable)

  Is there a good description how to set up Linksys RV016 for two WAN (ADSL + cable)? Looks like switching between two connections do not crack what is defined to WAN1 and which is defined to WAN2.

  I put the like load balancing
  -WAN1 all HTTP to the top/donw (cable) should go
  -WAN2 (DSL) GTalk, IMs, SMTP, POP3, IMAP, high-low must go
  but as it does not work like that.

  When I go to speedtest.net and test a connection I always get less amount then connected directly by cable:------also when people try to use any session or IP: sensitive web site it won't let me connect because the session has expired (IP-based) or IP was changed.

  Thanks for any help.

  Hello.

  These products are processed by the Cisco Small Business Support Community.

  * If my post answered your question, please mark it as "acceptable Solution".

  * Do not forget to give a 'congratulations '. Thank you!

• Services edit problems on RV016

  I need to change some firewall rules and the service on a RV016 using remote access management. I need to add a few new rules of firewall and need to add new services. But it is impossible to add a service.

  I click on "Service Management"-online "Service name" insert-online fill in the port range => click 'Add to list'-online now the new entry appears in the list =>, click on "Save Configuration". Close the small window and reload the Web page of the router. But nothing has changed. I can't add or delete any service (services wants to delete is not in use more!). It is also impossible to change an unnecessary entry.

  It is impossible to change the services through remote management?

  I tried to use 3 different customers to change services:

  -Mac OS X 10.6, Safari + Firefox (off Adblocker, popup blocker off, accept all cookies), Sandbox firewall off

  -Windows XP (using the Sun VM), Microsoft Internet Explorer

  -iPhone 3 GS - Safari mobile browser

  I also used 3 different internet connections. ADSL 2 x 1 x 3G

  Result: I can just edit and add services using the iPhone via 3 G (China Unicom) connection.

  I'm currently located in China.  The great wall has perhaps prevented service Editor to work properly.

• on howto RV016 subnet mask 255.255.0.0?

  Hello, I need to put my router linksys RV016 with the main IP 192.168.10.254 / 255.255.0.0, but I can´t choose this netmask!.

  255.255.255.0 is the greater ability to mask that I can use in the web application linksys.

  Yes... I can use the "Multiple subnet" and add a subnet with this mask... but I don't want to do...

  Is it possible to put a 255.255.0.0 mask like head mask on a RV016?

  Thank you

  Unfortunately, router Linksys support only class C subnet, this is a limitation of product and as I understand it, it's because Linksys was design to meet Small Office / Home Office or small business. This is the reason why you can not change the subnet of the said router.

• RV082 to RV016 gateway to gateway VPN

  Hello. I currently have a RV082 to setup VPN gateway to gateway RV016 between my office and home. The tunnel is connected and I have an installation Avaya IP phone and work. The problem is when I try to open a network folder shared on my server in the office. I ping the server and at the office. I can access some folders on the server using internet explore using the method 'name \\server\folder. But I can't open the files I have premapped. When I'm on the network in the office everything is ok. When I get home I get the message "path not found network". I tried to remap and go home empty-handed. Initially, I thought that maybe it's a setting on my server but rejected since I can ping and access through the method of EI. Any ideas? I get very frustrated here! Thank you.

  I thought about it by chance after reading several other posts of similar problems.  Under the gateway to gateway VPN configuration, you must navigate to the tab advanced for the IPSec configuration.  Both options of NAT Traversal and broadcast NetBIOS must be enabled at both ends and it works!

  Thanks for your help.

• Rv016 firmware update leads to broken Firewall tab

  Someone at - he lived or / and knows how to solve this problem?

  Then upgrade the Rv016 firmware from version v2.0.16 to v3.0.0.1 - tm by clicking on the tab Firewall now leads to a web page broken/not found, so as every other tab work correctly...

  This is the version of the firmware that includes a new tab for the Trend Micro ProtectLink Gateway Service

  Answers appreciated.

  Unfortunately, helm, you were right!

  Unfortunately every single config had to be rewritten manually...

  But it's working now, thank you very much.

• RV016 site-to-site with Netgear FVS318N does not connect

  I am completely dumbfounded about this.  Everything is even defined as a unit existing of Netgear FVS124G-which replaces the FVS318N.  Each option is completely identical.  It connects very well to other endpoints Netgear points, but not the rv016s.  And the existing Netgear connects very well.

  Any ideas?

  First car of Huntsville and bike e-magazine: www.huntsvillecarscene.com

  Samir,

  Aggressive mode is sometimes the key linking a tenacious tunnel.

  -Marty

• Cisco RV016 failover & load balance Multi WAN question

  Hello

  I think the RV016 is the camera to buy for our small building, but I'm a bit confused in the manual if my scheduled configuration is possible, so if you could confirm if this is possible I would appreciate it.

  We have a leased line as our main connection (lets call him WAN1). If this connection is not available, I don't want to load balance to any other network WAN.

  We have 2 netgear 4G devices identical (we'll call WAN 2 and 3 WAN). If the leased line is not available, I would like to then load balance these two WAN connections.

  Then I have a final connection, WAN4 as a slow adsl line. I don't know right now if I want to load balance this WAN1 or just have it as a backup to WAN2 and WAN3 failure (WAN2 and WAN3 have a 20 GB data limit each on their monthly allowance of the contract, if the leased line is down for more than a couple of days, what is unfortunately already happened) (then we reached this limit and then there is charged with extremely expensive data or just use the only ADSL)

  In any case, it's normal, I want to balance the load. I want to only load balance WAN3 and WAN2 WAN1 fails.

  Anyone know if this is possible? If not, is there any other similar device which would be appropriate?

  Thank you

  Ben

  Hi Bencarroll01,

  With RV016 you can get what you need.

  RV016 supports up to 7 WAN connection, and there are two mode of operation

  • Swing smart (Auto Mode): This option allows you to balance traffic between all interfaces increase the available bandwidth. The router balance traffic between the weighted alternating interfaces.
  • Group of IP (by users): Select this option for trafficking group on each WAN interface by levels of priority or classes of service (CoS). With this feature, you can ensure the bandwidth and a more high priority for specified services and users. All traffic that is not added to the IP group uses Intelligent balancing mode. To specify the services and users, click modify for the WAN interface and then add the entries of binding protocol for each service, IP address or IP address range.

  For our case, we must have RV016 configured with IP Group(By User), so in this case, we can configure binding protocol that we can specify and force all traffic from any IP address of the local network outside through WAN1. and any other WAN connection they always towards the TOP but not the traffic passing through them

  Now if WAN1 is down, immediately the rule to redirect traffic WAN 1 will be disabled and all traffic will pass through the rest of the WAN connection

  After that if the WAN1 is once again the binding protocol rule will be active again and again all the traffic will be done by WAN 1

  Please let me know if you have any other questions

  Please rate this post or marked as replied to help other customers of Cisco

  Greetings

  Mehdi

• RV016 SIP ALG

  Hello

  Since 2 weeks I have a problem with my voip provider.

  In my (3cx) pabx software, that my voip provider is correctly register but sometimes I do not know why I can not received internal call outside.

  When I call my voip provider, he told me to disable sip alg of my router but I can't find in my RV016 any sip algo option

  How do I do?

  My voip provider tell me to do the command line

  no ip nat service sip 5060 udp port

  in telnet but I'm looking and I can not telnet access because I can't login/password

  Thanks for your help

  Better compliance

  Loïc

  Hi love,

  You can try please from the browser: https://IPaddress_of_rv016/f_general_hidden.htm

  You will see the option of SIP ALG

  Please note the position or mark it as answered to help other customers of Cisco

  Thank you

  Mehdi

• port forwarding on Cisco RV016

  Hello

  Anyone know how to open a specific port on RV016?. I try different ways, but I get no polarity.

  I have to open ports for security cameras, and then I can see from outside my local network.

  If possible, it can either of you, show me how to do it please.

  Best regards

  Perez de Paris

  Hello

  If your access to the security camera in LAN with port 80 (by default)).

  You must configure the UPnp configuration under the menu setup:

  Add new service with the name "CAM1" with port80 internal and external port 81

  and configure the UPnp allowing to see page no.: 48 in link below.

  http://www.Cisco.com/c/dam/en/us/TD/docs/routers/CSBR/rv0xx/administrati...

• Traffic RV016

  I have a RV016 with an internal address of 192.168.1.1.  Also on the 192.168.1.0 network is a gateway server that the rest of my clients are sitting behind.  The customers are located on a network of 172.16.3.0/24.  All servers in fact bridge is before the packages.  To do this, no NAT.  There is a static route to the 172.16.3.0 on the RV016.

  So my question is how do I get the 172.16.3.0 traffic to route through the RV016?  Computers on the subnet can ping the RV016 and get a response, so I know that the gateway server that forwards packets between the two subnets very well and that the static method Router RV016 works.  All traffic trying to go beyond the RV016 never makes.  He disappears the RV016.  I checked all the ACL and that they should leave all traffic internal through.  Someone at - it suggestions?

  What firmware is your RV016 on?

  If it works on firmware 4.0.3.03 - tm, you need an additional access rule created to pass traffic to the subnet-172.

  Page 3 of the note of firmware version contains more information.

  http://www.Cisco.com/en/us/docs/routers/CSBR/rv0xx/release/RV0xx_RN_v4-0-3-3.PDF

• Remote VPN gateway to gateway problem RV016 to add VLANs

  Hi all I have a little problem with RV016. I have a site to another LAN ipsec virtual and I would like to add a vlan remote for tunneling but RV has only three options

  -IP

  -Subnet

  IP range-

  Now the remote lan for vpn is 192.168.10.0/24 and I would add 10.1.1.0/24

  Can someone help me?

  Glad to hear it

  Please note the post useful and mark it as answered to help other customers of Cisco

  See you soon

  Mehdi

• RV016 for 20 site to site VPN

  Best regards

  Currently I have a RV016 and a router RV110W to try to connect to one of our branches (retail of clothing) with the central site, we managed to install and VPN works very well, but we have more than 19 stores throughout the country.

  In stores, we can have 2 to 8 computers such as point of sale, one of them acting as server to our system, this server is required to connect to the main server in the central office.

  My question is: we have received some tips from people who say that these facilities are too small to connect to our 20 stores, anyone know if this is true? These RV series are suitable for this amount of connection of branches?

  Thanks in advance for any help!

  Hello

  The ASA5506 is a very good security device and give you a lot more security.   The RV016 isn't a security feature, but it has a firewall.  Less flexible, less features.

  You need the ASA5506-x w / power of fire and more security license.  With the license of security Plus the 5506 do support that 10 IPsec VPN tunnels.  With the license, it supports 50.

  The broadband VPN (speed), however, is substantially the same between the ASA and the RV016.  ASA get 100 Mbps VPN and the RV016 get 97 Mbit/s throughput.  very similar.

  The neck of the bottle is actually with the RV110w on the remote site.  There only get 5 Mbps VPN throughput.  You should consider the RV130W with 50 Mbps VPN throughput.

  Kind regards