Remote VPN gateway to gateway problem RV016 to add VLANs

Similar Questions

• Default VPN Gateway problem

  Hello guys. We have vpn site to site... and this is my scenairio.

  Site A (ASA 5505).

  VLAN 1 - outside = 200.200.200.x - internet

  VLAN 2-inside 192.168.8.1

  Eth0/1---192.168.8.2
  

  255.255.255.0
  

  Gateway 192.168.8.1

  
  

  It's my laptop

  Eth0/1 192.168.8.3
  

  255.255.255.0

  no gateway.

  LINUX Server

  For my site VPN remote B can reach my ip from 192.168.8.2 because of the gateway laptop I put it

  but he can't reach my Linux Sesrver 192.168.8.3 because there is no gateway.

  and I don't want to add a gateway my server for some reason... so please can someone help me out here, it's very important for me.

  You don't add gateway no choice to get connectivity.

  Thank you

  Ajay

• Cannot ping sub interface from my remote site VPN gateways

  I can't ping my gateways to interface my remote vpn connection sub

  I can ping 192.6.1.0 network, but can't ping network 192.6.2.0 or 192.6.3.0

  When I remote desktop in 192.6.1.20 I can ping all the networks, including gateways to interface sub.

  I think that something in my asa is misconfigured or not added

  ASA NAT rules:

  Exempt NAT Interface: inside

  Source 192.6.0.0/16

  Destination 192.6.10.96/27

  Static NAT interface: inside (it's for the local NAT of E0/0 out)

  Source 192.6.1.1/16

  Interface translated outside the Destination: 172.35.221.200

  Dynamic NAT interface: inside

  Source: no

  Destination: outside

  ASA access rules:

  Permit outside

  Source: no

  Destination: out

  Services: udp, tcp, tcp/http

  Static routes:

  Interface: Outside > network: all outdoors DSL (shows no DSL in the graph)

  

  Some incorrect configuration:

  On the ASA:

  (1) directions are incorrect, the default should point to the next hop route, that is to say: the internet router: 172.35.221.x, as follows:

  Route outside 0.0.0.0 0.0.0.0 172.35.221.x

  ---> where x must be the router internet ip address.

  existing routes need to be removed:

  No route outside 0.0.0.0 0.0.0.0 192.298.47.182 255

  No route outside 0.0.0.0 0.0.0.0 172.35.209.81 in tunnel

  (2) the following declaration of the static NAT is incorrect too and should be removed:

  static (inside, outside) USSLTA01_External USSLTA01 netmask 255.255.255.255

  --> You can not NAT interface on the SAA itself.

  (3) for the SAA within the interface's subnet mask should be 255.255.255.0, no 255.255.0.0. It should be the same as the router interface subnet mask:

  interface Ethernet0/1

  nameif inside

  security-level 100

  IP 192.6.1.254 255.255.255.0

  (4) on the way to access these sub interfaces subnet on the SAA as follows:

  Route inside 192.6.2.0 255.255.255.0 192.6.1.235

  Route inside 192.6.3.0 255.255.255.0 192.6.1.235

  Route inside 192.6.4.0 255.255.255.0 192.6.1.235

  On the router, configure it by default route as follows:

  IP route 0.0.0.0 0.0.0.0 192.6.1.254

• Cisco IOS - access remote VPN - route unwanted problem

  Hello

  I recently ran into a problematic scenario: I am trying to connect to a remote LAN (using a Cisco VPN client on my windows xp machine) my office LAN and access a server there. The problem is that I need a remote local network access at the same time.

  Remote LAN: 172.16.0.0/16

  LAN office: 172.16.45.0/24

  Topology:

  (ME: 172.16.10.138/25) - (several subnets form 172.16.0.0/16) - (Internet cloud) - (VPN-Gateway) - (172.16.45.0/24) - (TARGET: 172.16.45.100)

  To provide access, I configured a VPN to access simple distance on a 1700 series router. It's the relevant part:

  (...)

  crypto ISAKMP client config group group-remote access

  my-key group

  VPN-address-pool

  ACL 100

  IP local pool pool of addresses-vpn - 172.16.55.1 172.16.55.30

  access-list 100 permit ip 172.16.45.100 host 172.16.55.0 0.0.0.31

  (...)

  The configuration works fine, I can access the 172.16.45.100 server every time I need to. However, the problem is that when the VPN connection is connected, Windows wants to somehow rout the packets intended for 172.16.0.0/16 through the VPN tunnel. This is apparently due to a static route that added by the Cisco VPN Client and all other specific VPN routes.

  I suspect that the culprit is the IP LOCAL POOL, since when the VPN is connected, debugging of Client VPN log shows something like "adapter connected, address 172.16.55.1/16. Focus on the part "/ 16". I checked the VPN status page and the only road indicated there was "172.16.45.100 255.255.255.255" under remote routes. Local routes was empty.

  Is this a known problem I missed the obvious solution for? Is there no workaround apart from the pool local vpn penetrating high-end 10.x.x.x or 192.168.x.x? Thank you in advance for advice or tips!

  Hello

  The best way is to avoid any overlap between the local network and VPN pool.

  Try 172.17.0.0/16, is also private IP address space:

  http://en.Wikipedia.org/wiki/Private_network

  Please rate if this helped.

  Kind regards

  Daniel

• I need VPN gateway to gateway with NAT for several subnets, RV082

  I have a pair of RV082 routers and I would like to configure a gateway to gateway VPN tunnel, as described in a book, "How to configure a VPN tunnel that routes all traffic to the remote gateway," (name of file Small_business_router_tunnel_Branch_to_Main.doc).  I followed this recipe book and found that my while the main office has internet connectivity, the branch subnet is not an internet connection.

  Routing behaves as advertised, where all traffic goes to the seat.  However, the 192.168.1.0 subnet in the branch receives no internet connectivity.  I read in other posts that the main router will provide only NAT for the local subnet, not the Management Office subnet.  Is it possible to configure the RV082 router to provide NAT for all subnets?

  If this is not the case, what product Cisco will provide connectivity VPN Tunnel as well as the NAT for all subnets?  The RV082 can be used as part of the final solution or are my RV082s a wasted expense?

  Here is the configuration that I had put in place, (real IP and IKE keys are false).

  Bridge to bridge

  Remote Head Office

  Add a new Tunnel

  No de tunnel                  1                                               2

  Name of the tunnel:, n1 n1-2122012_n2-1282012-2122012_n2-1282012

  Interface: WAN1 WAN1

  Enable :                   yes                                             yes

  --------------------------------------------------------------------------------

  Configuration of local groups

  Type of local security gateway: IP only IP only

  IP address: 10.10.10.123 10.10.10.50

  Local security group type: subnet subnet

  IP address: 192.168.1.0 0.0.0.0

  Subnet mask: 255.255.255.0 0.0.0.0

  --------------------------------------------------------------------------------

  Configuration of the remote control groups

  Remote security gateway type: IP only IP only

  IP address: 65.182.226.50 67.22.242.123

  Security remote control unit Type: subnet subnet

  IP address: 0.0.0.0 192.168.1.0

  Subnet mask: 0.0.0.0 255.255.255.0

  --------------------------------------------------------------------------------

  IPSec configuration

  Input mode: IKE with preshared key IKE with preshared key

  Group of the phase 1 of DH: Group 5 - 1536 bit group 5 - 1536 bit

  Encryption of the phase 1: of THE

  The phase 1 authentication: MD5 MD5

  Step 1 time in HIS life: 2800 2800 seconds

  Perfect Forward Secrecy: Yes Yes

  Group of the phase 2 DH: Group 5 - 1536 bit group 5 - 1536 bit

  Encryption of the phase 2: of THE

  Phase 2 of authentication: MD5 MD5

  Time of the phase 2 of HIS life: 3600 seconds 3600 seconds

  Preshared key: MyKey MYKey

  Minimum complexity of pre-shared key: Enable Yes Enable

  --------------------------------------------------------------------------------

  If you are running 4.x firmware on your RV082, you must add an additional Allow access rule for the Branch Office subnet (considered one of the multiple subnets in the main office) may have access to the internet. Note the firmware version has more details about it.

  http://www.Cisco.com/en/us/docs/routers/CSBR/rv0xx/release/rv0xx_rn_v4-1-1-01.PDF

• QuickVPN - could not do a ping the remote VPN router!

  Hello

  I have a RV042 (VPN router) and I have some problems to run properly using the QuickVPN client.

  Here is the Log of the QuickVPN client.

  2008-10-15 20:14:38 [STATUS] a network interface detected with 192.168.0.104 IP address
  2008-10-15 20:14:38 [STATUS] connection...
  2008-10-15 20:14:38 [STATUS] connection to a remote gateway with IP address: 96.20.174.84
  2008-10-15 20:14:38 [WARNING] server certificate does not exist on your local computer.
  2008-10-15 20:14:44 remote gateway [STATE] has been reached with https...
  2008-10-15 20:14:44 [STATUS] commissioning...
  2008-10-15 20:14:51 [STATUS] Tunnel is connected successfully.
  2008-10-15 20:14:51 [STATUS] verification of network...
  2008-10-15 20:14:55 [WARNING] failed to do a ping the remote VPN router!
  2008-10-15 20:14:58 [WARNING] failed to do a ping the remote VPN router!
  2008-10-15 20:15:01 [WARNING] failed to do a ping the remote VPN router!
  2008-10-15 20:15:05 [WARNING] failed to do a ping the remote VPN router!
  2008-10-15 20:15:08 [WARNING] failed to do a ping the remote VPN router!
  2008-10-15 20:15:11 [WARNING] Ping has been blocked, which can be caused by an unexpected disconnection.
  2008-10-15 20:15:19 [STATUS] disconnection...
  2008-10-15 20:15:25 [STATUS] Tunnel is disconnected successfully.

  I don't know how it is implemented, but if WuickVPN wait a form ping my router, it will not happen. I was never able to ping my router ouside of my ISP network.

  There is a way to disable the Ping process and continue with the VPN connection?

  QuickVPN try ping on the router via the VPN tunnel to check the connection. It should work without worrying about whether your ISP filters ICMP messages or not. The tunnel is encrypted your ISP won't know what you're doing.

  Please post the corresponding on the RV042 VPN log. That is expected to see how far you get.

  You have a firewall running on the computer? I think that some firewalls have difficulty with the traffic of ESP.

  What is the router that is connected to the computer? How is it that is configured?

• remote VPN and vpn site to site vpn remote users unable to access the local network

  As per below config remote vpn and vpn site to site vpn remote users unable to access the local network please suggest me a required config

  The local 192.168.215.4 not able ping server IP this server connectivity remote vpn works fine but not able to ping to the local network vpn users.

  ASA Version 8.2 (2)
  !
  host name
  domain kunchevrolet
  activate r8xwsBuKsSP7kABz encrypted password
  r8xwsBuKsSP7kABz encrypted passwd
  names of
  !
  interface Ethernet0/0
  nameif outside
  security-level 0
  PPPoE client vpdn group dataone
  IP address pppoe
  !
  interface Ethernet0/1
  nameif inside
  security-level 50
  IP 192.168.215.2 255.255.255.0
  !
  interface Ethernet0/2
  nameif Internet
  security-level 0
  IP address dhcp setroute
  !
  interface Ethernet0/3
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Management0/0
  Shutdown
  No nameif
  no level of security
  no ip address
  management only
  !
  passive FTP mode
  clock timezone IST 5 30
  DNS server-group DefaultDNS
  domain kunchevrolet
  permit same-security-traffic intra-interface
  object-group network GM-DC-VPN-Gateway
  object-group, net-LAN
  access extensive list ip 192.168.215.0 sptnl allow 255.255.255.0 192.168.2.0 255.255.255.0
  192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0
  tunnel of splitting allowed access list standard 192.168.215.0 255.255.255.0
  pager lines 24
  Enable logging
  asdm of logging of information
  Outside 1500 MTU
  Within 1500 MTU
  MTU 1500 Internet
  IP local pool VPN_Users 192.168.2.1 - 192.168.2.250 mask 255.255.255.0
  ICMP unreachable rate-limit 1 burst-size 1
  enable ASDM history
  ARP timeout 14400
  NAT-control
  Global 1 interface (outside)
  NAT (inside) 1 0.0.0.0 0.0.0.0
  Route outside 0.0.0.0 0.0.0.0 59.90.214.1 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  dynamic-access-policy-registration DfltAccessPolicy
  the ssh LOCAL console AAA authentication
  AAA authentication LOCAL telnet console
  AAA authentication http LOCAL console
  AAA authentication enable LOCAL console
  LOCAL AAA authentication serial console
  Enable http server
  x.x.x.x 255.255.255.252 out http
  http 192.168.215.0 255.255.255.252 inside
  http 192.168.215.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  Crypto-map dynamic dynmap 65500 transform-set RIGHT
  card crypto 10 VPN ipsec-isakmp dynamic dynmap
  card crypto VPN outside interface
  card crypto 10 ASA-01 set peer 221.135.138.130
  card crypto 10 ASA - 01 the transform-set RIGHT value
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  crypto ISAKMP policy 65535
  preshared authentication
  the Encryption
  sha hash
  Group 2
  lifetime 28800
  Telnet 192.168.215.0 255.255.255.0 inside
  Telnet timeout 5
  SSH 0.0.0.0 0.0.0.0 outdoors
  SSH timeout 5
  Console timeout 0
  management-access inside
  VPDN group dataone request dialout pppoe
  VPDN group dataone localname bb4027654187_scdrid
  VPDN group dataone ppp authentication chap
  VPDN username bb4027654187_scdrid password * local store
  interface for identifying DHCP-client Internet customer
  dhcpd dns 218.248.255.141 218.248.245.1
  !
  dhcpd address 192.168.215.11 - 192.168.215.254 inside
  dhcpd allow inside
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  Des-sha1 encryption SSL
  WebVPN
  allow outside
  tunnel-group-list activate
  internal kun group policy
  kun group policy attributes
  VPN - connections 8
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  Split-tunnel-network-list value split tunnel
  kunchevrolet value by default-field
  test P4ttSyrm33SV8TYp encrypted password username
  username kunauto password bSHrKTGl8PUbvus / encrypted privilege 15
  username kunauto attributes
  Strategy Group-VPN-kun
  Protocol-tunnel-VPN IPSec
  tunnel-group vpngroup type remote access
  tunnel-group vpngroup General attributes
  address pool VPN_Users
  Group Policy - by default-kun
  tunnel-group vpngroup webvpn-attributes
  the vpngroup group alias activation
  vpngroup group tunnel ipsec-attributes
  pre-shared key *.
  type tunnel-group test remote access
  tunnel-group x.x.x.x type ipsec-l2l
  tunnel-group ipsec-attributes x.x.x.x
  pre-shared key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  Review the ip options
  inspect the netbios
  inspect the rsh
  inspect the rtsp
  inspect the skinny
  inspect esmtp
  inspect sqlnet
  inspect sunrpc
  inspect the tftp
  inspect the sip
  inspect xdmcp
  inspect the icmp
  !
  global service-policy global_policy
  context of prompt hostname
  call-home
  Profile of CiscoTAC-1
  no active account
  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
  email address of destination [email protected] / * /
  destination-mode http transport
  Subscribe to alert-group diagnosis
  Subscribe to alert-group environment
  Subscribe to alert-group monthly periodic inventory
  monthly periodicals to subscribe to alert-group configuration
  daily periodic subscribe to alert-group telemetry
  Cryptochecksum:0d2497e1280e41ab3875e77c6b184cf8
  : end
  kunauto #.

  Hello

  Looking at the configuration, there is an access list this nat exemption: -.

  192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0

  But it is not applied in the States of nat.

  Send the following command to the nat exemption to apply: -.

  NAT (inside) 0 access-list sheep

  Kind regards

  Dinesh Moudgil

  P.S. Please mark this message as 'Responded' If you find this information useful so that it brings goodness to other users of the community

• Remote VPN connected but do not go anywhere.

  within the network - ASA5505 = internet = remote VPN client.

  The ASA has a public IP address on the external interface and using PAT to the internet. He has only two interfaces, both inside and outside using the vlan. I created an IPSec VPN through CLI. My goal is for the remote client through the tunnel to through the Internet.

  Q1: Is it possible?

  Q2: the remote side is connected and has the IP address of the pool, with fact part of the network. But he can do nothing, including the gateway, which is inside the ping interface. I debug him, it shows the ASA receives the ping packets, but it is not send anything to the client. All recommend would be appreciated.

  Thank you

  Han

  Hello

  Can you please paste the result of ipconfig/all here?

  I hope this helps.

  Kind regards

  Anisha

  P.S.: Please mark this thread as answered if you feel that your query is resolved. Note the useful messages.

• Access remote vpn fails

  Hello

  Im trying to figure out why vpn for remote access is at our company office fails. The scenario: we currently have a work situation. The way this works is that users connect to the public ip address of the DSL router and nat vpn traffic to an internal router. This router then forwards the traffic to the vpn server.

  vpn client remote <=>{{internet}} <=>cpe <=>adsl router <=>vpn server

  Now, Im implementation of a 2nd internet line with more or less the same configuration, but instead of an adsl cpe, we use a cisco router. When users need to connect even with the only difference being a different public ip address

  client remote vpn <=>{{internet}} <=>cisco <=>router <=>router, vpn server

  So, the only change in the prepective of cisco vpn clients is the host.  However when testing, it didn't work. The vpn client times out. With something like 'the vpn peer did not' do not remember the exact error by heart. Now logic tells me that because he now works in the part between the internal router and the vpn gateway is ok. My guess is it's because of the cisco access list. I had my own list of access, but for some reason, I decided to use firewall SDM Wizard configuration and it generated this access list.

  Expand the IP 100 access list

  10 permit tcp any host 90.90.150.82 eq 4500

  20 permit tcp any host 90.90.150.82 eq 500

  30 permit tcp any host 90.90.150.82 eq 51

  40 permit tcp any host 90.90.150.82 eq 50

  50 permit tcp any host 90.90.150.82 eq 3101

  60 permit tcp any host 90.90.150.82 eq 993

  70 permit tcp any host 90.90.150.82 eq 587

  80 permit tcp any host 90.90.150.82 eq smtp (722 matches)

  90 deny ip 192.168.0.8 0.0.0.7 (20606 matches)

  100 permit icmp any host 90.90.150.82 - response to echo (113 matches)

  110 permit icmp any host 90.90.150.82 time exceeded (54 matches)

  120 permit icmp any inaccessible 90.90.150.82 host (1051 matches)

  130 deny ip 10.0.0.0 0.255.255.255 (726 matches)

  140 deny ip 172.16.0.0 0.15.255.255 all

  150 deny ip 192.168.0.0 0.0.255.255 everything

  160 deny ip 127.0.0.0 0.255.255.255 everything

  170 deny ip 255.255.255.255 host everything

  180 deny host ip 0.0.0.0 everything

  190 deny ip any any newspaper (5163 matches) Extended 100 IP access list

  Given that the natting to the smtp protocol works, I think that the natting is ok. I ping the server vpn, so routing also seems to be ok. Vpn users receive a vpn ip address pool 192.168.x.x. is it possible that the 150 rule that prevents them to connect? I can't test, because it's a living environment and I'll have to plan a window. Im just trying to figure out what is wrong, so I can fix it for a window. Someone at - it ideas?

  No, you don't need AH if your VPN policy does not include AH.

• Tunnel VPN remote Internet and VPN remote VPN from Site to Site traffic?

  Hello

  We try to remote traffic from our users VPN tunnel through our ASA 5510 as well as to allow the only access for remote user VPN traffic to the other end of the all our VPN site-to-site connected to the same ASA. Basically, we who want to VPN in the network in order to access all of our networks business. We try to get away with this without using split Tunneling.

  I can currently get internal traffic from the remote user VPN to reach all other vpn site-to-site tunnels without the internet in tunnel. The problem is when I add the following statement to the NAT:

  NAT (outside) 1 10.10.19.0 255.255.255.0 * 10.10.19.0 is the address of the remote VPN Client

  Internet traffic to the remote VPN starts to get in the tunnel, but I lose the opportunity to reach one of the other tunnels from site to site by the remote VPN tunnel.

  I also begin to receive the following errors in the journal of the ASA

  3 July 1, 2009 12:34:18 305005 10.10.19.255 137 no group of translation not found for udp src outside:10.10.19.3/137 dst outside:10.10.19.255/137

  Any help with how NAT statements must be defined for this work would be appreciated.

  Thank you

  Will be

  Will,

  the link of this post for your scenario of vpn hub & speak reference, you problem may be on exempt nat rules.

  Have a second look at your sheep rules.

  Be sure to eliminate tunnel rules related to rheumatoid arthritis, as appropriate, to not let him get in the way of splitting.

  http://forums.Cisco.com/eForum/servlet/NetProf?page=NetProf&Forum=security&topic=firewalling&TopicId=.ee6e1fa&fromOutline=true&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.2cc2e0f6/4

  If always emits discribe topology for l2ls and info logic RA and sanatized hub config asa... but I think if you look at the thread above, you should be able to solve.

  Concerning

• PIX 515 issuee remote VPN

  Did anyone see anything that would prevent a remote VPN to work? My L2L runs like a champ. I can connect via the remote VPN client end, but I can't talk about anything on the network. I see not the routes appear under my client software under the statistics section. Help!

  domain default.domain.invalid

  activate the password

  passwd

  names of

  interface Ethernet0

  nameif outside

  security-level 0

  IP xxx.xxx.xxx.xxx 255.255.255.248

  !

  interface Ethernet1

  nameif inside

  security-level 100

  address 192.168.3.1 IP 255.255.255.0

  !

  interface Ethernet2

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  passive FTP mode

  DNS server-group DefaultDNS

  domain default.domain.invalid

  90 extended access-list allow ip 192.168.3.0 255.255.255.0 192.168.2.0 255.255.255.0

  access-list 90 extended permit ip any 10.10.10.0 255.255.255.0

  acl_inside list extended access deny tcp 192.168.3.0 255.255.255.0 any eq smtp

  acl_inside of access allowed any ip an extended list

  access-list Split_tunnel_list note SPlit tunnel list

  Standard access list Split_tunnel_list allow a

  local pool YW #vpn 10.10.10.1 - 10.10.10.32 255.255.255.0 IP mask

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) - 0-90 access list

  NAT (inside) 1 0.0.0.0 0.0.0.0

  Access-group acl_outside in interface outside

  acl_inside access to the interface inside group

  Route outside 0.0.0.0 0.0.0.0 69.57.59.137 1

  Timeout xlate 03:00

  Timeout conn 04:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  the ssh LOCAL console AAA authentication

  AAA authentication LOCAL telnet console

  AAA authentication http LOCAL console

  AAA authentication enable LOCAL console

  LOCAL AAA authentication serial console

  Enable http server

  http 192.168.3.0 255.255.255.0 inside

  Crypto ipsec transform-set strong esp-3des esp-md5-hmac

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto-map dynamic outside_dyn_map 20 set pfs

  Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA

  PFS set 40 crypto dynamic-map outside_dyn_map

  Crypto-map dynamic outside_dyn_map 40 value transform-set ESP-3DES-SHA

  Marina 20 crypto card matches the address 90

  card crypto Marina 20 set peer 69.57.51.194

  card crypto Marina 20 set strong transform-set ESP-3DES-MD5 SHA-ESP-3DES

  map Marina 65535-isakmp ipsec crypto dynamic outside_dyn_map

  Marina crypto map interface outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 9

  preshared authentication

  3des encryption

  md5 hash

  Group 2

  life 86400

  crypto ISAKMP policy 20

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Crypto isakmp nat-traversal 20

  VPN-sessiondb max-session-limit 30

  Telnet 192.168.3.0 255.255.255.0 inside

  Telnet timeout 5

  SSH 69.85.192.0 255.255.192.0 outside

  SSH 67.177.64.0 255.255.255.0 outside

  SSH timeout 5

  SSH version 2

  Console timeout 0

  internal group YW #vpn policy

  YW #vpn group policy attributes

  Protocol-tunnel-VPN IPSec

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list Split_tunnel_list

  Group Policy - 69.57.51.194 internal

  attributes of Group Policy - 69.57.51.194

  Protocol-tunnel-VPN IPSec

  admin RqwfSgGaHexJEm4c encrypted privilege 15 password username

  attributes of user admin name

  Group-VPN-YW #vpn strategy

  tunnel-group 69.57.51.194 type ipsec-l2l

  IPSec-attributes tunnel-group 69.57.51.194

  pre-shared-key *.

  tunnel-group YW #vpn type ipsec-ra

  tunnel-group YW #vpn General-attributes

  YW #vpn address pool

  LOCAL authority-server-group

  authorization-server-group (outside LOCAL)

  Group Policy - by default-YW #vpn

  tunnel-group YW #vpn ipsec-attributes

  pre-shared-key *.

  !

  Policy-map global_policy

  class class by default

  Well, your main problem is your definition of correspondence address:

  Marina 20 crypto card matches the address 90

  It is the access list used for the sheep which includes access time S2S and remote, traffic used on correspondence address for the remote access connection, then go ahead and change it to avoid:

  Marina 192.168.3.0 ip access list allow 255.255.255.0 192.168.2.0 255.255.255.0

  No crypto Marina 20 card matches the address 90

  Marina 20 crypto card matches the address Marina

  and the other problem that is not afecting, but is badly configured is your policy of Split tunnel, you set the network as part of the split tunnel which is just as if you did nto have divided the active tunnel (where the reason why road shows 0.0.0.0 on the client)

  Go ahead and change it to be:

  Split_tunnel_list list standard access allowed 192.168.3.0 255.255.255.0

• Access to the internal mail (Exchange) by centimeters remote VPN server

  Hi all

  I have a problem in the configuration of ASA 5510 to access my internal mail (Exchange) through remote access VPN server

  one... I have set up my D-Link ADSL router to port before the SMPTP (25) & POP3 (110) to the external interface of ASA 5510 (192.168.5.101 255.255.255.0)

  b. How can I configure ASA 5510 (using ASDM) to portforward (SMTP POP3 110 25) to my internal mail server with IP 192.168.50.2 255.255.255.0

  c. my internal LAN network (192.168.50.0 255.255.255.0) is coordinated at 10.1.1.0 255.255.255.224 for vpn clients

  d. my IP of mail server (192.168.50.2 255.255.255.0) will also be translated while clients are accessing content through remote VPN access

  e.What IP (Exchange of IP of the server (192.168.50.2) do I have to set up in Microsoft Outlook (incoming & outgoing mail server), vpn clients receive using a NAT IP 10.1.1.10

  Here's my configuration details of access remote vpn

  : Saved

  : Written by enable_15 at 13:42:51.243 UTC Thursday, November 27, 2008

  !

  ASA Version 7.0 (6)

  !

  hostname xxxx

  domain xxxx

  enable the encrypted password xxxxx

  XXXXX encrypted passwd

  names of

  DNS-guard

  !

  interface Ethernet0/0

  nameif outside

  security-level 0

  IP 192.168.5.101 255.255.255.0

  !

  interface Ethernet0/1

  nameif inside

  security-level 100

  IP 192.168.50.101 255.255.255.0

  !

  interface Ethernet0/2

  Shutdown

  No nameif

  no level of security

  !

  interface Management0/0

  nameif management

  security-level 100

  management only

  IP 192.168.1.1 255.255.255.0

  !

  passive FTP mode

  list of access inside the _nat0_outbound extended permits all ip 10.1.1.0 255.255.255.224

  allow a standard vpn access list

  outside_cryptomap_dyn_20 list of allowed ip extended access any 10.1.1.0 255.255.255.224

  vpn-ip-pool 10.1.1.10 mask - 255.255.255.0 IP local pool 10.1.1.25

  Global interface 10 (external)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 10 0.0.0.0 0.0.0.0

  Route outside 0.0.0.0 0.0.0.0 192.168.5.1 (D-Link ADSL router LAN IP) 1

  internal vpn group policy

  attributes of vpn group policy

  Split-tunnel-policy excludespecified

  Split-tunnel-network-list value vpn

  WebVPN

  xxxxx xxxx of encrypted password privilege 0 username

  attributes of username xxxxx

  Strategy-Group-VPN vpn

  WebVPN

  ASDM image disk0: / asdm - 508.bin

  don't allow no asdm history

  ARP timeout 14400

  Enable http server

  http 192.168.1.0 255.255.255.0 management

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set ESP-3DES-SHA edes-esp esp-sha-hmac

  Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA

  card outside_map 655535-isakmp ipsec crypto dynamic outside_dyn_map

  outside_map interface card crypto outside

  ISAKMP allows outside

  part of pre authentication ISAKMP policy 10

  ISAKMP policy 10 3des encryption

  ISAKMP policy 10 sha hash

  10 2 ISAKMP policy group

  ISAKMP life duration strategy 10 86400

  tunnel vpn ipsec-ra group type

  VPN tunnel-group general attributes

  ip vpn-pool address pool

  Group Policy - by default-vpn

  Tunnel vpn ipsec-attributes group

  pre-shared-key *.

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  management of 192.168.1.2 - dhcpd address 192.168.1.254

  dhcpd lease 3600

  dhcpd ping_timeout 50

  enable dhcpd management

  !

  Policy-map global_policy

  class inspection_default

  inspect the dns-length maximum 512

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  !

  global service-policy global_policy

  : end

  So can someone help me, how can I configure these tasks

  You can without problem

• Tunnel remote VPN Site to Site

  Hello

  I am facing a problem with my remote VPN users, I describe my network here. I have a site to another tunnel for my USA, tht IP 169.X.X.X. office client, we are able to connect this tunnel. now I configured remote vpn for users of my home, my office inside the IP is 192.168.2.X and once I connect to home, in the office through vpn cisco client, then, my ip is 192.168.3.X I put the IP in ASA pool, now 192.168.3.X and 192.168.2.X communicates correctly , but I need to access my Tunnel IP 169.1.X.X also from 192.168.3.X (Home).

  203.92.X.X is my static public Ip address that is allowed in the client side for the tunnel.

  If something confussing please let me know.

  Thank you

  Nitin

  Nitin,

  It is not possible to have a NATing on 192.168.3.0/24 to public ip address because it has default route (which you can reach L2L remote host) on the SAA pointing to the external interface. This default route will be redirect/road traffic on the external interface only vpn client so NATing will reach us.

  HTH

  Sangaré

• Remote VPN on ASA5540

  Here's the situation

  I am slowly migrating from a Cisco VPN 3030 to a Cisco ASA5540 hub

  My L2L tunnels come along fine, but I'm running issues with attachment for remote VPN Clients.

  I implemented the AAA and it works correctly, as well as the profile.  (we use IPSec)

  My issues are with the IP Pool address.   We use a different set of the IP as the hub.

  I have implemented routing on the next hop within the ASA as the home of the ip address pool of.

  But I don't get any through put.

  Can I join the ASA with a Client remote check the Radius Server and all authentication through.  But I can't access anything whatsoever.

  All lanes of route for the IP address pool from within the network to the ASA.

  Is there something else I need to put in place also just assign the IP address Pool?

  any suggestions would be helpful

  Thank you

  The problem isn't necessarily routing. Check the following things:

  1. have you for the pool VPN nat exemption (you need)... If this isn't the case you will see on any group of translation found syslog messages and traffic will be dropped. Assume that your VPN pool is 172.16.4.0 255.255.255.255. You add:

  sheep ip access-list allow any 172.16.4.0 255.255.255.0

  NAT (inside) 0 access-list sheep

  2. do you have an access-group applied to the interface? Make a ' group-access show run. If you have applied, make sure that the access list permits traffic at the pool of the VPN client

  3. If it is IPSec and the customer or the SAA is behind a NAT, you must have the following:

  ISAKMP nat-traversal

  -heather

  Please rate this message if this helped you.

• VPN router to the problem of the ASA

  Hello world.

  I am doing a VPN between a router and a series of ASA5500 and difficulties.

  The router part is 100% correct because it is a daily task, but miss me something on the side of the ASA of the things.

  The ASA also has remote via IPsec tunnels clients as you'll see below, so I have to make sure that continues to work!

  It is a fairly urgent question. So any help or advice can be provided, it would be very appreciated!

  Here is the router part:

  !

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  Group 2

  isakmp encryption key * ASA-PUBLIC-IP address

  ISAKMP crypto keepalive 100

  !

  !

  Crypto ipsec transform-set transform-set esp-3des esp-md5-hmac

  !

  10 customers map ipsec-isakmp crypto

  defined ASA-PUBLIC-IP peer

  transform-set transform-Set

  match address 102

  QoS before filing

  !

  !

  Access-list 100 remark [== NAT control ==]

  access-list 100 deny ip 192.168.2.0 0.0.0.255 10.1.1.0 0.0.0.255

  access-list 100 permit ip 192.168.2.0 0.0.0.255 any

  Access-list 102 remark == [VPN access LISTS] ==

  access-list 102 permit ip 192.168.2.0 0.0.0.255 10.1.1.0 0.0.0.255

  Access-list 102 remark

  (Crypto card has been applied to the corresponding interface)

  SIDE OF THE ASA:

  permit inside_nat0_outbound to access extended list ip 10.1.1.0 255.255.255.0 10.1.1.192 255.255.255.224

  prevpn_splitTunnelAcl list standard access allowed 10.1.1.0 255.255.255.0

  access-list Interior-access-in extended permit ip 10.1.1.0 255.255.255.0 any

  access-list Interior-access-in extended permit icmp 10.1.1.0 255.255.255.0 any

  access list for distance-extended permitted ip network 10.1.1.0 255.255.255.0 192.168.2.0 255.255.255.0

  Global (outside) 1 ASA-PUBLIC-IP

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 10.1.1.0 255.255.255.0

  NAT (inside) 0 192.168.2.0 255.255.255.0

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto-map dynamic outside_dyn_map 20 the transform-set ESP-3DES-MD5 value

  card crypto outside_map 40 match remote-network address

  card crypto outside_map 40 game peers REMOTE-router-IP

  outside_map card crypto 40 the transform-set ESP-3DES-MD5 value

  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

  outside_map interface card crypto outside

  ISAKMP allows outside

  part of pre authentication ISAKMP policy 10

  ISAKMP policy 10 3des encryption

  ISAKMP policy 10 md5 hash

  10 2 ISAKMP policy group

  ISAKMP life duration strategy 10 86400

  tunnel-group prevpn type ipsec-ra

  tunnel-group prevpn General-attributes

  address pool VPN-pool

  Group Policy - by default-prevpn

  prevpn group of tunnel ipsec-attributes

  pre-shared-key *.

  tunnel-group REMOTE-router-IP type ipsec-l2l

  REMOTE-router-IP tunnel-group ipsec-attributes

  pre-shared-key *.

  Hi Chris

  first on the router make this change to littil than u ned to add md5 as hashing whil employees u th in the asa and the router u did not, so the default is sha!

  do

  crypto ISAKMP policy 1

  md5 hash

  now on the SAA as I see that there is a problem in nat0 you line l2l tunnel

  so that you need to look like:

  permit inside_nat0_outbound to access extended list ip 10.1.1.0 255.255.255.0 192.168.2.0 255.255.255.0

  You also need a permit for the ipsec traffic, the following command will allow all ipsec traffic if you want to filter traffic not to use this command and use rather ACLs on the external interface, but following that to allow all traffic to your L2L and remote vpn access:

  Permitted connection ipsec sysopt

  so, please:

  clear xlate and reload the ASA then attempt to leave the expmtion NAT new effects

  Good luck

  If useful rates