RV082 and fast VPN

Similar Questions

• VPN between RV082 and WRT54G

  Hello
  I have problem with connection RV082 and WRT54G via VPN (gateway to gateway type).
  I created tunnel on the RV082, but ofcurse he does ' t work. Firewall on both routers is off.
  My setup
  RV082
  WAN address: 83.15.211.170 (DSL)

  WAN network mask: 255.255.255.248

  WAN gateway: 83.15.211.169

  Local address: 192.168.0.244
  Local netmask 255.255.255.0

  Local gateway: 192.168.0.244
  WRT54G
  WAN address: 95.50.235.202 (DSL)
  WAN network mask: 255.255.255.248 (the same ISP)
  WAN gateway: 93.50.235.201
  Local address: 192.168.1.1
  Local netmask: 255.255.255.0

  Local gateway: 192.168.1.1
  VPN:
  Local group: 192.168.0.0/255.255.255.0
  Remote group: 192.168.1.0/255.255.255.0
  Remote gateway: 95.50.235.202
  Everything seems to be correct, but I can not connect to RV082 to WRT54G. I have no error in the logs. Help, please

  The WRT54G is without VPN router. But there is no VPN capabilities. You cannot configure a tunnel VPN on the WRT54G.

• Can fast VPN and VPN Cisco coexist (WRVS4400N)

  I am looking to buy a WRVS4400N to take care of my home network.  While I get out on the road I want to VPN in my home network to my laptop (on which I installed Cisco VPN for the company's mobile access to my corporate network).  In this spirit, I have three questions:

  1. is the Cisco VPN client on my laptop be able to establish a VPN connection to unity WRVS4400N?  I suspect not, and instead, I have to use fast VPN.

  2. I understand there are problems in co existence with different suppliers, VPN clients (when I tried before with a Netgear router, the VPN Netgear client broke the Cisco VPN client).  Quick VPN client Linksys can coexist with the Cisco VPN client without any problems?

  3. a last resort, if Cisco and Linksys VPN can coexist, install the client quick VPN Linksys inside a VM Ware image would work (while the Cisco VPN client is still installed in the host operating system).

  Thanks much for any help.

  (1) correct.  For WRVS4400N QVPN

  (2) I run the Cisco VPN CLient and VPN fast on my laptop and seems fine

• RV082 and Windows 7, no internet connection with active firewall

  Hello

  I have a 1.3.98 - tm firmware RV082 and have recently upgraded several Machines to glass & RC for testing, but they can't access the internet.

  They can access all the other mahcines internal, but cannot ping the router.  The first Pc I upgraded was beautiful and accessible to the internet without problem.

  The second started Ok but then loses the internet connection.  It can access all internal machines and if I reboot it with XP (dual boot) it works fine.  He has been an operational machine without problems netowrk for 2 or 3 years.  I tried a diffetrn nic card and another cable froma different wall point in case there was a problem that XP could cicumvent and Windows 7 has been more difficult.

  Now the second PC has started doing the same thing and wont connect to internet.

  If I disable the firewall on the RV082 Windows 7 PC connect correctly.  Can I wathc the tray icon of system on the State of PC modification simply chagnign the status of the firewall on the router.

  Occasioanlly a PC will continue to work for a short period before losing internet again or blocked him.  I have checkled newspapers and others are no entries in the standard newspaper.

  I bypassed Vista Batteux ther so a setting or something I need to change on the window smachines, but as I have Windows 7 on test in withotu the Council to clarify a problem and my two lapotps and have connected through various cafes, Internet etc. even in Spain and Brazil without problem I tend to think it's a problem with the RV082.

  Any ideas would be helpful?

  Thank you

  Kevin

  All specifications are as follows, I tried you understand all of the same information if some irrelevant1 may be:

  No antivirus on the PC yet!

  IBM PC with 4 GB of RAM, pnetium 3.06, 80 GB hdd 2 partitions dual boot Windows XP and Windows 7 Ip static (but tests with DHCP as well) 10.1.2.13 - 2 3com 3cT 1000 + cards internal network - REaltek 10/100 (disabled)

  IP 10.1.2.13 void 255.255.255.0 Gateway 10.1.2.1 dns 222.222.222.14

  Reference Dell GX520 with 1 GB of RAM 80 GB drive hard new installation Windows 7 dhcp

  RV082 LAN 10.1.2.1 sub 255.255.255 DHCP issue. In theory irrelevant, but there are 3 VPN tunnels to the 10.1.3.0, 10.1.4.0 and 10.1.5.0 networks

  WAN1 222.222.222.11 void 255.255.255.248 gw 222.222.222.14 dns 222.222.222.14

  WAN2 disabled/empty

  Loads of transfer App for phone system Avaya, RDP, HTTP, HTTPS, FTP, TFTP, SMTP, POP3, Netware etc etc etc.

  IP 222.222.222.14 is a 3com office connect ADSL router

  LAN 222.222.222.14 sub 255.255.255.248

  WAN DHCP of BT ADSL

  222.222.222 ip addresses have been changed for safety!

  This set up was valid for 2 or 3 years without problems

  Hey Kevin,

  To clarify, we have not heard of this I didn't think (I am curious as well), did this start happening when you upgraded the computers?

  Its sounds like it from what I've read, and also you can generate by activating and deactivating the FW on request, but this didn't happen until you have changed the PC SW?

  If it does, then, looks like soemthing SW PC made and maybe you can endure a wireshark trace and try to sniff which continues when the PC tries to access the internet.   I'm not asking to review track, only that it can help you.    If you feel like it is a defect of the Cisco product, you can open a folder with the Small Business Support Center and they will watch the track with you.

  Steve DiStefano

  IS

  Sales Channel field in the United States

• Error Client Services for NetWare has disabled the Welcome screen and fast user, any change by changing the account settings

  Original title: "Client Services for NetWare."

  When I try to change my account settings, I get this message "client for NetWare has disabled the display of welcome and Fast User Switching.

  To restore these features, you must uninstall Client Services for Netware ".»

  I checked and the customer service is not installed on this computer.

  He puts this message up no matter what I try.

  What can I do to remove this problem?

  Hello

  Were there any changes made to the computer before the show?

  Please follow the steps in the link.

  Error message when you try to turn on welcome screen or Fast User Switching

  http://support.Microsoft.com/kb/315347

• How to activate the screen of welcome and fast user switch client services for netware

  How to activate the screen of welcome and fast user switch client Services for NetWare...

  How to restore and step to uninstall client services for netware

  Hello

  Your question of Windows is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the public on the TechNet site. Please post your question in the below link: http://social.technet.microsoft.com/Forums/en-US/winserverPN

• Larger and faster hard drive model T61 6458-CTO

  6i would like to know which is the hard drive bigger and faster that I can buy for a T61 (6458-CTO).

  It has a 80 GB hard drive, 5400 RPM and SATA interface (1.5 Gb/s).

  Can I buy a SATA II (3 Gb/s, 500 GB and 7200 RPM) for this computer?

  Thank you.

  Jon

  > Buy a SATA II (3 Gb/s and 500 GB 7200 RPM) for this computer?

  Yes, you can, however, due to limitations in the T61, there only a SATA I interface. This isn't really a problem because the drive itself is unable to transfer data at the maximum speed of the interface.

• Upgrade a Dell Inspiron 531 to something with more memory and faster?

  Hello, I have a Dell Inspiron 531, 32-bit operating system, and the 3G memory in it but is Vista. I tried to upgrade to Windows 7, but after many attempts, could not go without having to clear everything and start over. So I'd do it if I have to do I was wondering if I could make the machine that is more memory better and faster, without having to buy a new computer say a Dell XPS 8300 (that I'll have to run a lot of photographic software in the future and I understand that this could be a good computer for that?) In any case, it is possible to 'upgrade' the computer something like this please, or I have to save my pennies for a new? Thank in advance for your advice.)

  Hello

  If you upgraded to 4GBs off RAM you won't get many benefits

  Here is an article on what is happening with 4GBs of RAM:

  http://support.Microsoft.com/kb/929605

  "If a computer has many features implemented, the available memory can be reduced to 3 GB or less." However, the maximum memory available in 32-bit versions of Windows Vista is typically 3.12 GB. »

  and you should also consult the Dell manual for your model desktop computer see what amount of RAM your motherboard would answer anyway

  http://support.Dell.com/support/topics/global.aspx/support/my_systems_info/manuals?c=us&l=en&s=Gen& ~ CK = anavml

  and here is the reason why you can not upgrade to Windows 7

  There are no Windows 7 drivers written for her by Dell

  http://support.Dell.com/support/downloads/DriversList.aspx?c=US&l=en&s=GEN&ServiceTag=&SystemID=INSP_DSKTP_D531&OS=WLH&OSL=en&CATID=&impid=

  Click on the menu at the link above drop-down operating system

  itonlt has XP and Vista drivers available

• PC hangs for a few seconds, and then return as normal and fast as always, no reports of any problems in the operating system.

  Hello world

  I have a Vista Ultimate SP2 system and all updates, my hardware is an AMD Athlon 64 x 2 3.2 Ghz with a RAID 0 (2 discs), 4 GB of RAM, video memory shared up to 1 GB, Asus M2A-VM Motherboard.

  My problem is that sometimes when you work with any my computer shutdown application package to meet any keyboard or mouse control for 2-3 seconds and suddenly come back with tasks in the queue and fast as usual.

  I've updated my Chipset and RAID drivers.

  I uninstalled ASUS ACPI Center who could be one of the causes of this problem, rename the executable to Center asus acpi.

  I ran TuneUp Disk Doctor to verify my RAID and fix problems

  I update and updated my Antivirus ESET Smart Security in order to improve the performance of the process EKRN who sometimes take a large part of the time CPU.

  Can someone advice me how track and what tools to use to run a diagnosis of systemd and check if my problem is with the hardware or the operating system?

  Kind regards.

  JUOX.

  Run process monitor. Stop the trace when your problem occurs. Look through the timestamps of the gaps.

  See this for an example of the use of Process Monitor to diagnose a deadlock:

  http://blogs.technet.com/markrussinovich/archive/2010/01/13/3305263.aspx

• Cisco and Checkpoint VPN clients on a single PC

  Hello

  I'm in the following fix:

  I had used customer Checkpoint SecuRemote 4.1 SP - 5 VPN in the past.

  Now, I have installed the Cisco VPN client version 4.0.4 on my PC to access IPSec VPN for the PIX in our headquarters.

  According to Cisco VPN release notes http://www.cisco.com/univercd/cc/td/doc/product/vpn/client/rel404/404clnt.htm#wp1346340 , it should be possible to have clients both Cisco and Checkpoint VPN installed on the same machine.

  But I am not able to connect to my PIX, I receive the following error message:

  "Secure the complete VPN connection locally by the Client.

  Reason 403: failed to contact the security gateway. »

  When I'm looking for signs of PC control-> system-> hardware-> device Administration-> network cards, I can see Cisco Systems VPN Adapter disabled.

  After you activate manually, I always get the same error when you try to connect to the Cisco VPN client.

  After PC restart the Cisco VPN adapter is disabled later.

  I tried to uncheck Check Point SecuRemote form my Dial-up connection (bypassing CSCea31192 of bug, but the bug does not affect NAT - T connection which I use).

  I noticed the same situation on three different computers, one running Windows XP, both running Windows 2000.

  After uninstalling the client Checkpoint completely (including Windows registry manual removal), the Cisco VPN client works very well.

  It seems to me, therefore, that there is a profound mismatch between Cisco and Checkpoint VPN clients.

  Does anyone know of a workaround?

  Thank you

  Milan

  We had the same problem with some of our users who need to use the two clients to connect to customer sites.

  If I remember the cisco client does not start automatically, but the client of checkpoint 4.1 don't.

  We by-passed by deleting the registry entry point control that starts the client at startup. fwenc.exe is the entrance and it is in

  HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Run

  After that make a shortcut to the executable file that is stored in the directory \bin to relevant checkpoint on the client (it is different from NT & 9 client x) and then only start when it is necessary.

  Hope that's a help

• Site2Site and remote VPN

  I have a site2site between PIX506 and 877 router VPN. Site A has PIX506 and Site B router a in 877. I configured site2site VPN and it worked fine. I also configured remote VPN on PIX 506 so that the remote user can access A site. But when I configure remote VPN on PIX506 site2site VPN works and both sides can ping each other. But site B users cannot access any resource network or application of the SiteA while site A can access resources of site B. After removing remote VPN site configuration B can access the resources of the Site I joined the configuration of the two sites. Someone help me please site2site and remote VPN work at the same time.

  Please forgive me for not reading every line.

  an add-on quick about the pix configuration:

  change "isakmp key * address 213.181.169.8 netmask 255.255.255.255" at "isakmp key * address 213.181.169.8 netmask 255.255.255.255 No.-xauth No. config-mode.

• ASR1K and SSL VPN

  I'm having trouble finding information on SSL VPN for ASR1K, when we bought the boxes told us that SSL VPN was on the roadmap of the software, but that was back in 2010 and now I can not find anything nor can I get the right information.

  Does anyone have a recommendation on what to do or who to ask?

  PLS, contact your Cisco account manager as he or she would be able to provide additional information.

  There is normally a long list of features to add to the product, and SSL VPN is one of them who was asked to appear on the ASR. However, depending on the needs, it might be on the top of the list of the road map, or to the bottom of the list. Your Cisco AM should be able to get information from the product team.

• Problems of DNS with RV082 and OSX Lion

  Hello

  I have a problem with DNS resolution, using a Mac and a router RV082.

  I use the Google DNS, it manually until 8.8.8.8 and 8.8.4.4

  The simpton is that DNS resolution is slow or fails in the Mac App Store, Firefox, Safari, etc.. I once solved this in hard reseting the RV082 and get to the page were it ask a firmware and does not work until you download the firmware.

  I did this same procedure, but no longer works. Everyone knows this too?

  Thank you

  Oliver

  Hi oliversl1,

  Thank you for posting. Please provide additional information:

  1. What type of internet connection? (Cable, DSL, T1)
  2. No matter what Windows PC? If so, it works ok?
  3. A new hardware version 3, is the RV082? If this is not the case, do you know how old he was?
  4. What version of the firmware?

  Please as well see the following:

  https://supportforums.Cisco.com/thread/2022782

  We also had a problem with Mac computers and RV0xx which has been tentatively scheduled by a downgrade of firmware. I think it was firmware version 1.3.12.19 - tm who had problems with the Mac.

• WebVPN and remote VPN access

  Hello

  Is there a difference between WebVPN and remote VPN access or they are the same.

  Thank you.

  access remote vpn consists of

  -IPSEC VPN remote access. It is part of the ASA, no permit required, requires pre-installed Client from Cisco VPN IPSEC on PC

  -with AnyConnect SSL VPN remote access. It requires licensing of SSL VPN on SAA. AnyConnect client can be installed automatically on the PC with the launch of web.

  -with Essentials AnyConnect SSL VPN remote access. Beginning with ASA 8.2 (1), almost license $ 0. It's the same AnyConnect client as in the previous article, but it cannot be installed automatically with the launch of web. It must be previously installed as of Cisco IPSEC VPN client.

  -webvpn aka clientless vpn. It is a portal HTTPS which allows HTTP connections, file sharing, telnet, RDP and much more (with smart tunnels) resources without having to install a real client on the PC. It requires licensing of SSL VPN on SAA. It cannot be used if "AnyConnect Essentials" license is activated on SAA after 8.2 (1)

  Kind regards

  Roman

• PIX and ASA static, dynamic and RA VPN does not

  Hello

  I am facing a very interesting problem between a PIX 515 and an ASA 5510.

  The PIX is in HQ and has several dynamic VPN connections (around 130) and IPsec vpn remote works very well. I had to add a PIX to ASA L2L VPN static and it does not work as it is supposed to be. The ASA 5510, at the remote end, connects and rest for a small period of time, however, all other VPN connections stop working.

  The most interesting thing is that ASA is associated with the dynamic map and not the static map that I created (check by sh crypto ipsec his counterpart x.x.x.x). However, if I make any changes in the ACL 'ACL-Remote' it affects the tunnel between the PIX and ASA.

  Someone saw something like that?

  Here is more detailed information:

  HQ - IOS 8.0 (3) - PIX 515

  ASA 5510 - IOS 7.2 (3) - remote provider

  Several Huawei and Cisco routers dynamically connected via ADSL

  Several users remote access IPsec

  A VPN site-to site static between PIX and ASA - does not.

  Here is the config on the PIX:

  Crypto ipsec transform-set ESP-3DES-ESP-SHA-HMAC-IPSec esp-3des esp-sha-hmac

  Dyn - VPN game 100 Dynamics-card crypto transform-set ESP-3DES-ESP-SHA-HMAC-IPSec

  Crypto dynamic-map Dyn - VPN 100 the value reverse-road

  VPN - card 30 crypto card matches the ACL address / remote

  card crypto VPN-card 30 peers set 20 x. XX. XX. XX

  card crypto VPN-card 30 the transform-set ESP-3DES-ESP-SHA-HMAC-IPSec value

  VPN crypto card - 100 - isakmp dynamic Dyn - VPN ipsec

  interface card crypto VPN-card outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  md5 hash

  Group 2

  life 86400

  crypto ISAKMP policy 65535

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  access list ACL-remote ext ip 10.0.0.0 allow 255.255.255.0 192.168.1.0 255.255.255.0

  Thank you.

  Marcelo Pinheiro

  The problem is that the ASA has a crypto acl defined between host and network, while the remote end has to the network.

  Make sure that the acl is reversed.