RV320 as SBS2011 router as DHCP server and use IPSEC

Similar Questions

• I get RAS ip in my DHCP server and the place of the incoming connection in my network

  I don't know I have not configured any VPN server in my system and all of the servers, I checked the option for remote access, it is not configured in one of my servers, but after each reboot, I get a (inbound connection) in my network places and 1 IP address in the DHCP server leases, I mean that 1 IP show my correct address of the computer in DHCP and another IP for RAS ,

  Help, please

  Adil-

  Hi adil

  Your question is addressed in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the following forums.

  TechNet - Windows Server category:
  http://social.technet.Microsoft.com/forums/en/category/WindowsServer

  Concerning

• Replication of data between SQL Server and using Oracle11g materialized view.

  I have Sqlserver 2005 as my source and oracle11g as my target. I need fill out the target daily with change of the source data.
  to do this, we created a dblink between SQL Server and oracle and reproduced this table as a point of view, materialized in Oracle.
  problem that we get here is fast refresh option is not available.each day it will pick up all of the data source.
  is it possible to use Fast refresh in this scenario?
  
  Thanks in advance.
  
  Kind regards
  Balaram.

  You can try MS SQL replication.
  Configure transactional Standard of MS SQL and Oracle Publication subscriber http://msdn.microsoft.com/en-us/library/ms151738%28v=sql.90%29.aspx

• Misconfigured remote VPN server by using IPSEC client

  I'm trying to figure out what I did wrong in my setup.  The environment is:

  ASA 5505 running 8.2 with 6.2 ASDM.

  Version of the VPN Client 5.0.05.0290

  I installed VPN ipsec clients both anyconnect and connected successfully to the remote access VPN server. However, the client doesn't show any returned package.  Thinking that I have badly configured, I have reset to the default value of the factory and began again.  Now I only have the configured ipsec vpn and I have exactly the same symptoms.  I followed the instructions to configure the ipsec vpn in Document 68795 and double-checked my setup and I don't know what I did wrong.  Because I can connect to the internet from inside network and I can connect to the VPN from outside of the network (and the ASDM Watch monitor an active connection with nothing sent to the client) I believe this is a road or an access rule preventing communication but I can't quite figure out where (and I tried the static routes to the ISP and a wide variety of access rules before rinsing to start) above).

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  WebVPN
  internal group vogon strategy
  attributes of vogon group policy
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list vogon_splitTunnelAcl
  username password privilege encrypted 0987654321 zaphod 15
  username password encrypted AaBbCcDdEeFf privilege 0 arthur
  username arthur attributes
  VPN-group-policy vogon
  tunnel-group vogon type remote access
  tunnel-group vogon General attributes
  address pool VPN_Pool
  strategy-group-by default vogon
  tunnel-group vogon ipsec-attributes
  pre-shared-key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  !
  global service-policy global_policy
  context of prompt hostname
  Cryptochecksum:xxxxxxxxxxxxxxxxxxxxxx
  

  Looks like a typo for the Pool of IP subnet mask.

  You currently have:

  mask 10.92.66.10 - 10.92.66.24 255.255.0.0 IP local pool VPN_Pool

  It should be:

  mask 10.92.66.10 - 10.92.66.24 255.255.255.0 IP local pool VPN_Pool

  Please kindly change the foregoing and test, if it still does not work, please please add the following:

  management-access inside

  Policy-map global_policy
  class inspection_default

  inspect the icmp

  Then try to VPN in and see if you can ping 10.92.65.1 and let us know if this ping works.

  Please also share the output of: "cry ipsec to show his" after the trial, if it does not work.

• Set up an account IMAP CS (incoming server) and use a POP3 ATT account as outgoing server by default

  I'll put up Compuserve account a friend in Windows Mail.  The incoming for CS server is IMAP.cs.com, she does not see his e-mail in Windows Mail.  But instead of Compuserve to forward emails received by them, I want to send using its account of ATT (POP3). So I entered the server information emerging from ATT in the CS account. FROM in the stills of forwarded e-mail says * address email is removed from the privacy *.  And even though I select ATT from the drop in FROM trying again send CS.

  Several years ago I got CS and Bellsouth and I put in place so I could send email rcvd Bellsouth CS, but I used Outlook 2003.

  Is this possible in Windows Mail and if so how?

  PS I'm currently wean her out of CS.

  Hello

  The port to block SMTP some 25 PSI if the account is not their own email account and it did not appear on a computer connected to the original location.

  In other words, POP3, Windows Mail, Outlook, or any other any Web Mail application would receive messages from any account but willsend only if users have an e-mail account with the ISP and mail that his envoys from the ISP email account.

  It is one of the measures to avoid 3rd party spammers using accounts of others in order to Spam.

  Jack MVP-networking. EZLAN.NET

• I have a server with windows Small Business Server 2011. I need to uninstall windows SBS and install Win 7 pro on this server and use it as my personal computer. is this possible?

  I have a server that I do not use. She has windows SBS 2011.  I need to convert this powerful server to my PC I need.  Please tell me if this is possible, and how to do this.

  Thank you

  Could you provide the specifications of the server?

  Companies often convert departmental servers to client machines of the time when they are upgrading to the most recent. The process should be easy by inserting the Windows 7 disc and perform a custom installation.

  Consider the following text:

  How to: perform a customized Windows installation

  See the section for Windows 7.

• Using Cisco AP as router and DHCP server

  I'm a newbie in the technology of Cisco wireless. I have a lot of Cisco wireless access point. One of them (1142AG-K9 Cisco) I want to set them up as a DHCP server and will forward traffic to the public ip address as it will route the traffic to 203.82.203.50 (Ip provided by ISP) and will lease ip as associated devices 192.168.10.0 pool.

  Even though I know that it is possible using a router on the AP. But it is possible using a single access point?

  If so, how?

  Help, please.

  Hi, the AP cisco are just basic layer 2 devices such as a hub or Layer 2 switch, it does not any layer 3 as a wireless router.

  The Cisco access point supports to have a VLAN or subnet configured or more VLANS or subnets and will pass all traffic to a layer 3 devic so that traffic can be routed to the need.

  The Ap can't stand to have an addrees ip configured on the bvi1 for the management.

  Also the build in the ap dhcp option is very limited and will only know the ip address to wirless clints that connect to it on an ssid linked to its management interface in this case that the bvi1 and all them VLAN othe or subnets shall not use an external dhcp server.

  Sent by Cisco Support technique iPhone App

• WLC - server DHCP (Override) and

  Hi guys,.

  A little confused. If I want my wireless clients to a DHCP address on my business DHCP servers, I need to click the Overrides button, for the WLC to act as a relay agent or the docs say that this happens by default?

  Can someone pls confirm, because it is a little confusing. The files help mentioned below also?

  Thx a lot indeed.

  Ken

  Server DHCP (Override)

  ----------------------

  When the substitution is selected, you can enter the IP address of your DHCP server. It is a required field for some configurations of WLAN. There are three valid configurations:

  -DHCP Server override on a valid DHCP and DHCP address assignment requested server IP address: requires that all WLAN clients obtain an IP address from the DHCP server.

  -DHCP Server override on a valid DHCP and DHCP address unnecessary assignment server IP address: allows all clients WLAN get an IP address from the DHCP server or use a static IP address.

  -DHCP Server OFF Overrides: guests WLAN using the DHCP setting in the Management Interface, not the static address of the Forces.

  Hi Ken,

  Your WLC default is DHCP relay, you do not need to override.

  The WLAN configuration, put you in an interface. If you check this configuration of the interface, you will see that it points to a DHCP server. This is where your WLC relays to wireless clients.

  If you wish to override this setting and to send your customers to a different DHCP server instead, you then click DHCP replace in the WIFI config and enter another IP DHCP address.

  HTH

  Jerome

• Pwerconnect 6224: vlan client computers do not receive the ip address of DHCP server on a different VLAN

  Hello

  I have a prolem routing dhcp requests between the vlan management where DHCP server resides and the other VLANs.

  I have the scenario of base with three VLANS: vlan 10 (management vlan), 20, 30, configured on a Powerconnect 6224 switch L2 mode. This switch is connected to a pfsense router. The router is configured at the package of road between the VLANS and it does it well.

  In Vlan 10, I have a configured DHCP server to use the ip addresses of all the VLANS (10, 20, 30). VLAN 10 client computers receive ip address but not others from other VLANs.

  When I put the ip address in the appropriate range of VLANs manually on computers, I ping the server and I have connectivity.

  This suggests that the problem is with the dhcp package.

  The following is the configuration of the switch:

  Configure
  database of VLAN
  VLAN 10,20,30
  VLAN 1 1 routing
  VLAN 20 2 routing
  VLAN 30 3 routing
  output
  SNTP server time.nist.gov
  clock timezone 1 minutes 0
  battery
  1 1 member
  2 2 Member
  output
  DHCP IP address
  IP address vlan 10
  name of the IP-server 172.16.10.1

  bootpdhcprelay cidridoptmode
  interface vlan 1
  Routing
  IP 172.16.1.1 255.255.255.0
  output
  interface vlan 20
  Routing
  address 172.16.20.1 IP 255.255.255.0
  output
  interface vlan 30
  Routing
  IP 172.16.30.1 255.255.255.0
  output
  level of 20fc49459a1898b923ed3ec7b3e81276 user name 'admin' password encrypted 15
  No spanning tree
  spanning tree priority 0
  l2relay DHCP
  DHCP l2relay VLANs 10, 20-30
  DHCP l2relay circuit-id VLANs 10, 20-30
  !
  interface ethernet 1/g2

  l2relay DHCP
  switchport access vlan 20
  output
  !
  interface ethernet 1/g3
  l2relay DHCP
  switchport access vlan 30
  output
  !
  interface ethernet 1/g21
  switchport access vlan 10
  output
  !
  interface ethernet 1/g22
  switchport access vlan 10
  output
  !
  interface ethernet 1/g23
  switchport access vlan 10
  output
  !

  interface ethernet 1/g24
  switchport mode trunk
  switchport trunk allowed vlan add 10,20,30
  output
  Server SNMP community EyesOfNetwork ro
  SNMP-server community public ro
  output

  I followed the instructions in the powerconnect 6224 user guide, but no progress on this issue.

  Any help will be be grateful.

  Thank you

  Zoubeir

  The DHCP server stores information that could be useful? May need to configure monitoring ports and something as wireshark to monitor DHCP packets. This would help determine where the package is stopping.

  example:

  Console (config) #monitor session 1 source interface 1/g8

  Console (config) #monitor session 1 destination interface 1/g10

  session mode 1 #monitor console (config)

  right now I don't see anything in the config of the switch that stands out. If the DHCP server is configured for option 82, then you will need to include the following command on the switch.

  Example:

  Trust l2relay console #dhcp (config-if-1/g1)

  But I don't think that's our scenario here.

• Virtual machines do not get IP address from the DHCP server

  Hello! I just spend Xenserver to ESXi. Created a couple of virtual machines and none of them gets an IP address from our DHCP server (DHCP server is a physical PC), and instead, they get a number of internal 192.168.x.y allowing connection to the internet.

  Looks like a way to do this is to install a virtual machine that is a router, as M0n0wall, and route traffic to connect to the external network and finally to access internet. But this is not what I have to do.

  I need to have virtual machines that are server to get an IP reserved for our DHCP server, and then our local windows client should be able to access it directly.

  I searched on google and forums for this but I can't seem to find how to configure virtual machines to directly belong to our local network.

  I thought that VMware would have a simpler way to do so than XenServer, but I was stuck on this one day now and really frustrated as I get not before with this project, stuck on this little problem... sigh...

  Thanks for your help.

  GER.

  ESXi does not IP addresses to the virtual machines it host - if the virtual machines are not able to access your physical network than that of the thw two virtual machines acts as a DHCP server - now to the question of network - if you are not able to reach the virtual machines on the physical network or achieve fitness network virtual machines , then there is a problem with the physical connection to the ESXi host, possibly the configuration of the physical port that connects to the - is a way to test this theory to assign an IP address on the same network that the management port - if you are able to access the virtual machine, then you know that the problem is with the switch port.

• laboratory test for 2008 Server and clients

  I'm new to vmware and I hope to have a preview on if or how I can create a mini enviornment for testing 2008 Server and clients.

  (Study for MCITP)

  I am running:

  Windows 7 Professional 64 using vm worksation 7.1.3

  Intel Core2 Extreme 6850 @3.7 GHz

  8 GB RAM

  RAID 0 SSD

  Guest operating system located on 2 drives internal seagate 7200 RPM

  Linksys wrt300n router

  I already did a team and installed (1) Server 2008R2, (1) WinxpSP3, Ent of Win7 (1), Clone of Ent Win 7 (1)

  I would like to install 3 server roles, AD, DNS and DHCP for beginners.

  I am considering establishing a separate virtual lan for systems work in that I can do my tests.

  Providing a static IP address for the server and using dhcp by server for customers of victory.

  I also want to create another team, so I can do some tests with SBS 2011 so without interfering with the first team and or my home network

  Any advice or comments would be greatly appreciated.

  Thank you

  I thought that someone has already done and was hoping a ' oh yes, that's what you do, it's easy "answer...

  Yes I could do that and these questions have already been answered ad nauseam, but I'll tell you why I do not give indications of the steps step-by-step when I see things like "(Education pour MCITP)" and it's because if you can't figure it out on your own, you are not qualified to be a professional anything whatsoever in my book! "   Now please don't take that as harsh as it may seem I have really don't mean that highly however the point I'm trying to do is, especially when it is currently professionally, with labour or professional certifications, I certainly don't expect any who all know on a given topic a, but what I expect is a part to be able to find the answers that are already out there When it is not the very first person to come across a given number.

  I gave the server a static ip address, I booked on the router and used in bridge for the adapter. AD and DNS has worked well, but the dhcp service has failed. It seemed at odds with the dhcp router.

  Of course, it will conflict with router DHCP Server of the local physical network when you use bridged on a virtual machine running a DHCP server, it is basic networking question.

  Is there a way to do a virtual router? I want the team to be separate and not have the ability to 'see' my dhcp router, or any other PC.

  But I need to pull the static information and dns somehow.

  It's there, reading the chapters 14 and 15 are along with networks in general orders and there are several diagrams in these two chapters which, in my opinion, help to give you the answers to these questions.

  There are several ways to reach your goal and I know for a fact that he has already covered by these forums and other places on the Internet it seems ridiculous to repeat it once again here and beside that you really learn if responses are just handed to you vs student, research, practice, etc..

• Satellite Pro C650 can't find our DHCP server

  Hello

  We just recived 8 new Satellite Pro C650 and care about their image.
  When connect us to our network via a cable and boot on LAN of the laptop can not find our DHCP server and so of does not obtain an IP address.

  If we connect to an another laptop\workstation in the same Manor, it works very well.

  All the settings are correct in the BIOS.

  Any ideas.

  Hello

  First of all, you should check if the settings of TCP/IP to connect to the local network.
  Network-> properties-> LAN (local area) connections-> TCP/IP-> properties

  Here, you should check if the options for the IP address, DNS are set to obtain automatically.
  In the advanced settings of TCP/IP in IP settings tab active DHCP must be visible.

  In addition, please check if all firewalls do not prevent the laptop to connect to the local network.

• New DHCP server not to issue the IPS (2012 R2)

  Having a new DHCP server is going. Authorized and not coming error. Turn off the old DHCP server and try to renew the lease of the IP, and nothing happens. What is the problem?

  I forgot to change the IP addresses of switches support. :( Everything works. :)

• Windows 7 - using VMware installation start the DHCP server

  Original title: Question

  When I try and install windows 7 using vmware its Dungeon rather start the DHCP server and then start from the selected ISO file I selected

  

  Hello Cordy,

  Thanks for posting your question on the forum of the Microsoft community.

  The question will be better suited to the audience of professionals on the TechNet forums.

  I would recommend posting your query in the TechNet forums.
   
  TechNet Forum
  http://social.technet.Microsoft.com/forums/en-us/home?category=w7itpro

  In addition, you can also contact VMware support for assistance.

  See this link:
  http://www.VMware.com/in/support.html

  Thank you

• Start the server wds with cisco dhcp server

  Salvation;

  I want to use the cisco dhcp server and I do not know which option I need to put my dhcp server

  Tanx

  You must contact Cisco support to help them with their product.