Misconfigured remote VPN server by using IPSEC client
I'm trying to figure out what I did wrong in my setup. The environment is:
ASA 5505 running 8.2 with 6.2 ASDM.
Version of the VPN Client 5.0.05.0290
I installed VPN ipsec clients both anyconnect and connected successfully to the remote access VPN server. However, the client doesn't show any returned package. Thinking that I have badly configured, I have reset to the default value of the factory and began again. Now I only have the configured ipsec vpn and I have exactly the same symptoms. I followed the instructions to configure the ipsec vpn in Document 68795 and double-checked my setup and I don't know what I did wrong. Because I can connect to the internet from inside network and I can connect to the VPN from outside of the network (and the ASDM Watch monitor an active connection with nothing sent to the client) I believe this is a road or an access rule preventing communication but I can't quite figure out where (and I tried the static routes to the ISP and a wide variety of access rules before rinsing to start) above).
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal group vogon strategy
attributes of vogon group policy
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list vogon_splitTunnelAcl
username password privilege encrypted 0987654321 zaphod 15
username password encrypted AaBbCcDdEeFf privilege 0 arthur
username arthur attributes
VPN-group-policy vogon
tunnel-group vogon type remote access
tunnel-group vogon General attributes
address pool VPN_Pool
strategy-group-by default vogon
tunnel-group vogon ipsec-attributes
pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:xxxxxxxxxxxxxxxxxxxxxx
Looks like a typo for the Pool of IP subnet mask.
You currently have:
mask 10.92.66.10 - 10.92.66.24 255.255.0.0 IP local pool VPN_Pool
It should be:
mask 10.92.66.10 - 10.92.66.24 255.255.255.0 IP local pool VPN_Pool
Please kindly change the foregoing and test, if it still does not work, please please add the following:
management-access inside
Policy-map global_policy
class inspection_default
inspect the icmp
Then try to VPN in and see if you can ping 10.92.65.1 and let us know if this ping works.
Please also share the output of: "cry ipsec to show his" after the trial, if it does not work.
Tags: Cisco Security
Similar Questions
-
Hello world
I have a cisco router 2800 installed in our companyand I have it configured as a VPN server for professional help (cisco configuration)with the ease of the VPN Server WizardCan I connect to this server using windows XP or 7 dialog VPN?Hello
Your question of Windows 7 is more complex than what is generally answered in the Microsoft Answers community. It is better suited for the IT Pro TechNet public. Please post your question in the TechNet Forum. You can follow the link to your question:
http://social.technet.Microsoft.com/forums/en-us/w7itpronetworking/threadsI hope this helps!
-
Access to the internal mail (Exchange) by centimeters remote VPN server
Hi all
I have a problem in the configuration of ASA 5510 to access my internal mail (Exchange) through remote access VPN server
one... I have set up my D-Link ADSL router to port before the SMPTP (25) & POP3 (110) to the external interface of ASA 5510 (192.168.5.101 255.255.255.0)
b. How can I configure ASA 5510 (using ASDM) to portforward (SMTP POP3 110 25) to my internal mail server with IP 192.168.50.2 255.255.255.0
c. my internal LAN network (192.168.50.0 255.255.255.0) is coordinated at 10.1.1.0 255.255.255.224 for vpn clients
d. my IP of mail server (192.168.50.2 255.255.255.0) will also be translated while clients are accessing content through remote VPN access
e.What IP (Exchange of IP of the server (192.168.50.2) do I have to set up in Microsoft Outlook (incoming & outgoing mail server), vpn clients receive using a NAT IP 10.1.1.10
Here's my configuration details of access remote vpn
: Saved
: Written by enable_15 at 13:42:51.243 UTC Thursday, November 27, 2008
!
ASA Version 7.0 (6)
!
hostname xxxx
domain xxxx
enable the encrypted password xxxxx
XXXXX encrypted passwd
names of
DNS-guard
!
interface Ethernet0/0
nameif outside
security-level 0
IP 192.168.5.101 255.255.255.0
!
interface Ethernet0/1
nameif inside
security-level 100
IP 192.168.50.101 255.255.255.0
!
interface Ethernet0/2
Shutdown
No nameif
no level of security
!
interface Management0/0
nameif management
security-level 100
management only
IP 192.168.1.1 255.255.255.0
!
passive FTP mode
list of access inside the _nat0_outbound extended permits all ip 10.1.1.0 255.255.255.224
allow a standard vpn access list
outside_cryptomap_dyn_20 list of allowed ip extended access any 10.1.1.0 255.255.255.224
vpn-ip-pool 10.1.1.10 mask - 255.255.255.0 IP local pool 10.1.1.25
Global interface 10 (external)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 10 0.0.0.0 0.0.0.0
Route outside 0.0.0.0 0.0.0.0 192.168.5.1 (D-Link ADSL router LAN IP) 1
internal vpn group policy
attributes of vpn group policy
Split-tunnel-policy excludespecified
Split-tunnel-network-list value vpn
WebVPN
xxxxx xxxx of encrypted password privilege 0 username
attributes of username xxxxx
Strategy-Group-VPN vpn
WebVPN
ASDM image disk0: / asdm - 508.bin
don't allow no asdm history
ARP timeout 14400
Enable http server
http 192.168.1.0 255.255.255.0 management
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-3DES-SHA edes-esp esp-sha-hmac
Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA
card outside_map 655535-isakmp ipsec crypto dynamic outside_dyn_map
outside_map interface card crypto outside
ISAKMP allows outside
part of pre authentication ISAKMP policy 10
ISAKMP policy 10 3des encryption
ISAKMP policy 10 sha hash
10 2 ISAKMP policy group
ISAKMP life duration strategy 10 86400
tunnel vpn ipsec-ra group type
VPN tunnel-group general attributes
ip vpn-pool address pool
Group Policy - by default-vpn
Tunnel vpn ipsec-attributes group
pre-shared-key *.
Telnet timeout 5
SSH timeout 5
Console timeout 0
management of 192.168.1.2 - dhcpd address 192.168.1.254
dhcpd lease 3600
dhcpd ping_timeout 50
enable dhcpd management
!
Policy-map global_policy
class inspection_default
inspect the dns-length maximum 512
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
!
global service-policy global_policy
: end
So can someone help me, how can I configure these tasks
You can without problem
-
RV320 as SBS2011 router as DHCP server and use IPSEC
p {margin-bottom: 0.25 cm; line-height: 120% ;}}
Our society is really eager to acquire a VPN Cisco RV320 router to replace our old insecurity only PPTP VPN-router. Before actually buying the router, there are a few questions I'd like to have answered.
In our current setup, we have a SBS2011 standard Server which is used as a DHCP, DNS, Exchange, and SMB server to our network of the company, all the peripheral functions within the same network (192.168.0.1/24).
We would like to add the RV320 to our network to allow access of employees to the corporate network when they are at home or on the road using IPSEC VPN (client site).In our current configuration us use (or used) a VPN router and VPN clients allowed to acquire an IP address from the PPTP server, these IP addresses have fallen in a range that the DHCP SBS2011 server was free to distribute the. It's quite simple actually
How can we configure the router RV320 so that there will be any conflict between the RV320 router and SBS2011 Server regarding distributing them IP addresses to the VPN IPSEC clients?
Can configure us the RV320 to transfer earlier requests DHCP server SBS2011? We want all customers (including IPSEC VPN clients so that they enter the same network).
Is it possible to simply using the DHCP-relay option (in the web interface) and entering the IP address of the server SBS2011?We should disable the DHCP on the router-RV320, or is there another way to continue using the SBS2011 server as the DHCP server, while allowing client-to-site IPSEC VPN for access to our local network?
Thanks in advance
Hello and thanks for the exam Cisco for your network needs.
First of all, I understand that you are used to working with the PPTP connection and now you want to switch to a more secure IPSec connection.
It's a great idea, but there are a few things to consider:
1. the RV320 supports the IPSec VPN via the Cisco VPN Client 5.0, you can download it from the site Web of Cisco if after you buy a contract for the router.
The contract will set will cost about $70, depending on where you decide to buy it, but it has several features including 3 years of telephone support 24/7 and next day replacement guarantee for business if the unit doesn't respond, it also allows you to download special software like the Cisco VPN Client.
2. for client VPN connection, you can not, or you need to try to relay the DHCP request what, whether the router will handle it and he will probably be on a different subnet from your local network, but it will you access to all devices on the network.
3-If you do not want to buy the contract, then you can always use PPTP to the RV320 and it will give you the same access that you are already accustomed.
I hope that was helpful, please let us know if you have any other questions.
-
Try to connect to a remote VPN server
This task was bleeding in my eyes. I can't make it work. I understand the principle of TCP-OUT ACCORD - IN but can't seem to reconcile it kind includes the firewall.
Long and short of the situation:
Company a static IP address assigned by the local society of DSL
All computers inside network enjoy outdoor internet access and interconnectivity
Remote VPN host has static IP
Configuration VPN of a properly established and the remote control accounts are active.
Does not connect when good ID and PASSWORD are entered.
Anyone tried this before. Please assume that I have the skill level of a child of 5 years and the patience of the same thing.
Thank you for your help.
Timothy S. Murray
A child under 5 huh? looks like a lot of people that I care. I'm kidding anyone, not me flame.
In any case, we need a little more information here to go, it's a connection to a PIX PPTP you talk, or a router? Or is it IPSec (you mentioned GRE, that's why I think you speak of free WILL). Is the user authentication is done locally on the endpoint VPN device, or is it a server Radius/GANYMEDE involved?
Can you send in the configuration of the end device, ensuring xxxxx valid IP addresses and passwords?
-
IOS VPN L2L + C2L (cisco IPSEC client)
Hello
need to configure a C2L (client to the LAN) vpn on a cisco router where there is already an ipsec vpn.
!!! already configured on the ROUTER
!
crypto ISAKMP policy 1
md5 hash
preshared authentication
address of cisco key crypto isakmp 0.0.0.0 0.0.0.0
!
!
Crypto ipsec transform-set esp - esp-md5-hmac Tunnel
!
crypto dynamic-map 10 Road-Tunnel
game of transformation-Tunnel
match address 115
!
!
!
!
Crypto map 10 ipsec-isakmp Crypto-Tunnel Dynamic Channel-Tunnel
!
point-to-point interface ATM0/1/0.1
card crypto Crypto-Tunnel
!
access-list 115 permit ip 10.0.0.0 0.0.0.255 192.168.168.0 0.0.0.255
access-list 115 permit ip 10.0.0.0 0.0.0.255 10.2.0.0 0.0.0.255
access-list 115 deny ip 10.0.0.0 0.0.0.255 any
!
!!! new configuration for cisco ipsec client
!
no address Cisco key crypto isakmp 0.0.0.0 0.0.0.0
address of cisco key crypto isakmp 0.0.0.0 0.0.0.0 no.-xauth
!
AAA new-model
!
AAA authentication login AutClient local
AAA authorization groupauthor LAN
!
!
username 0 pippo pippo
!
crypto ISAKMP policy 10
BA 3des
preshared authentication
Group 2
!
ISAKMP crypto client configuration group vpnclient
key 0-pippo
DNS 10.10.10.10
WINS 10.10.10.20
domain cisco.com
pool ippoolvpnclient
Save-password
ACL 188
!
!
card crypto Crypto-Tunnel client authentication list AutClient
card crypto Crypto-Tunnel isakmp authorization list groupauthor
card crypto Crypto-Tunnel client configuration address respond
card crypto Crypto-ipsec-isakmp dynamic dynmap Tunnel 20
!
Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
!
Crypto-map dynamic dynmap 10
match address 188
Set transform-set RIGHT
!
!
!
!
IP local pool ippoolvpnclient 10.99.0.1 10.99.0.30
!
access-list 188 note #.
access-list 188 note # split tunneling VPN C2L
access-list 188 allow ip 10.99.0.0 0.0.0.31 10.0.0.0 0.0.0.255
!
can you tell me if the new configuration is OK?
Thank you all
NOT the ACL should be the opposite. Sound from the point of view of the router.
access-list 188 allow ip 10.2.0.0 0.0.0.255 10.5.0.0 0.0.0.31
Concerning
Farrukh
-
Error connecting to the server by using the Client VMware vCenter
When you attempt to connect to vCenter server using vSphere client, I get this message:
"a general error has occurred: authorize the exception."
However, if I log on the vCenter server locally and use a local Windows account in vSphere Client to connect to vCenter Server on the same computer - it works OK.
There is obviously a problem with what happens when you use active directory to authenticate a user who connects with the VMware vCenter server client.
Someone has seen this before or have any ideas?
Thank you
I had a similar problem on two different sites
- It was my firewall local windows on my Windows 7 desktop that it has prevented from work
- Another situation was DNS was not working properly and once I had a static entry, it worked
-
Remote VPN access to authenticate the Client by (real IP)?
Hi all
I need to authenticate the user to remote access VPN in additional to the username & password I will give you to him, I need to authenticate the real IP that he will use to connect to the ASA. Is this possible?
Thanks in advance...
Hello
Unfortunately, this is not possible because demand will relay just the user name and password for authentication and no real ip address.
I hope this helps.
Kind regards
Anisha
P.S.: Please mark this thread as answered if you feel that your query is resolved. Note the useful messages.
-
Easy remote VPN - IPsec Session count
I have recently updated our ASA5510 head to our datacenter to 8.2.1 to 8.4.5. The ASD has been also improved 6.2.1 to 7.1. (1) 52. Under the old code, a connected remote ASA5505 via remote VPN easy showed 1 IPsec tunnel. However, after the upgrade, it shows 42 sessions. It seems to me that each split tunnel network defined in the easy VPN profile is being counted as a tunnel. Someone has seen this, or is - it possible that I may have something misconfigured now that the code is upgraded? Thank you.
Dave
No, IMHO, it's a display error in ASDM for 7.1.
Return to ASDM 6.4.9 and it should be 1 tunnel.
-
Connection to a VPN server enterprise, via an existing Internet connection - PPPoE
Hi, I want to buy a router "EtherFast Cable / DSL VPN Router with 4-Port 10 / 100 Switch (BEFVP41) ' there is only one question: can I connect to the Internet on the PPPoE connection and use this connection to connect to the VPN server of your company through PPPoE or IPSec?
You can connect to the Internet via the PPPoE connection on your router.
If you use a VPN client software to connect to the secure your company network, there is usually a remote VPN server inside waiting to accept a connection of employees outside the corporate network. All Linksys routers support VPN pass through and work with these types of connections. The only time that you need VPN Tunnel to the capabilities of the BEFVP41 is if you manually configure a secure VPN connection between two physical locations.
-
Hello
Is there a difference between WebVPN and remote VPN access or they are the same.
Thank you.
access remote vpn consists of
-IPSEC VPN remote access. It is part of the ASA, no permit required, requires pre-installed Client from Cisco VPN IPSEC on PC
-with AnyConnect SSL VPN remote access. It requires licensing of SSL VPN on SAA. AnyConnect client can be installed automatically on the PC with the launch of web.
-with Essentials AnyConnect SSL VPN remote access. Beginning with ASA 8.2 (1), almost license $ 0. It's the same AnyConnect client as in the previous article, but it cannot be installed automatically with the launch of web. It must be previously installed as of Cisco IPSEC VPN client.
-webvpn aka clientless vpn. It is a portal HTTPS which allows HTTP connections, file sharing, telnet, RDP and much more (with smart tunnels) resources without having to install a real client on the PC. It requires licensing of SSL VPN on SAA. It cannot be used if "AnyConnect Essentials" license is activated on SAA after 8.2 (1)
Kind regards
Roman
-
Inside the server can't ping remote vpn client
My simple vpn client can accumulate the tunnel vpn with my Office ASA5510 success and my vpn client can ping the internal server. But my internal server cannot ping the remote vpn client. Even the firewall vpn client windows is disable.
1. in-house server can ping Internet through ASA.
2 internal server cannot ping vpn client.
3 Vpn client can ping the internal server.
Why interal Server ping vpn client? ASA only does support vpn in direction to go?
Thank you.
Hello
Enable inspect ICMP, this should work for you.
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the icmp
inspect the icmp errorinspect the icmp
To configure the ICMP inspection engine, use the command of icmp inspection in class configuration mode. Class configuration mode is accessible from policy map configuration mode.
inspect the icmp
HTH
Sandy
-
Urgent issue: remote vpn users cannot reach server dmz
Hi all
I have an asa5510 firewall in which remote vpn client users can connect but they cannot ping or access the dmz (192.168.3.5) Server
They also can't ping the out interface (192.168.2.10), below is the show run, please help.
SH run
ASA5510 (config) # sh run
: Saved
:
: Serial number: JMX1243L2BE
: Material: ASA5510, 256 MB RAM, Pentium 4 Celeron 1599 MHz processor
:
ASA 5,0000 Version 55
!
Majed hostname
activate the encrypted password of UFWSxxKWdnx8am8f
2KFQnbNIdI.2KYOU encrypted passwd
names of
DNS-guard
!
interface Ethernet0/0
nameif outside
security-level 0
IP 192.168.2.10 255.255.255.0
!
interface Ethernet0/1
nameif inside
security-level 100
192.168.1.10 IP address 255.255.255.0
!
interface Ethernet0/2
nameif servers
security-level 90
192.168.3.10 IP address 255.255.255.0
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
Shutdown
No nameif
no level of security
no ip address
!
boot system Disk0: / asa825-55 - k8.bin
passive FTP mode
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
acl_outside to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.1.0 255.255.255.0
acl_outside list extended access allow icmp 192.168.5.0 255.255.255.0 192.168.1.0 255.255.255.0
acl_outside of access allowed any ip an extended list
acl_outside list extended access permit icmp any one
acl_inside list extended access allowed host ip 192.168.1.150 192.168.5.0 255.255.255.0
acl_inside list extended access allowed host icmp 192.168.1.150 192.168.5.0 255.255.255.0
acl_inside list extended access allowed host ip 192.168.1.200 192.168.5.0 255.255.255.0
acl_inside list extended access allowed host icmp 192.168.1.200 192.168.5.0 255.255.255.0
acl_inside list extended access allowed host ip 192.168.1.13 192.168.5.0 255.255.255.0
acl_inside list extended access allowed host icmp 192.168.1.13 192.168.5.0 255.255.255.0
acl_inside to access ip 192.168.1.0 scope list allow 255.255.255.0 host 192.168.3.5
acl_inside list extended access allow icmp 192.168.1.0 255.255.255.0 host 192.168.3.5
acl_inside list extended access deny ip 192.168.1.0 255.255.255.0 192.168.5.0 255.255.255.0
acl_inside list extended access deny icmp 192.168.1.0 255.255.255.0 192.168.5.0 255.255.255.0
acl_inside of access allowed any ip an extended list
acl_inside list extended access permit icmp any one
acl_server of access allowed any ip an extended list
acl_server list extended access permit icmp any one
Local_LAN_Access list standard access allowed 10.0.0.0 255.0.0.0
Local_LAN_Access list standard access allowed 172.16.0.0 255.240.0.0
Local_LAN_Access list standard access allowed 192.168.0.0 255.255.0.0
access-list nat0 extended ip 192.168.0.0 allow 255.255.0.0 192.168.0.0 255.255.0.0
allow acl_servers to access extensive ip list a whole
acl_servers list extended access allow icmp a whole
pager lines 24
Outside 1500 MTU
Within 1500 MTU
MTU 1500 servers
IP local pool 192.168.5.1 - 192.168.5.100 mask 255.255.255.0 vpnpool
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 621.bin
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
interface of global (servers) 1
NAT (inside) 0 access-list nat0
NAT (inside) 1 192.168.1.4 255.255.255.255
NAT (inside) 1 192.168.1.9 255.255.255.255
NAT (inside) 1 192.168.1.27 255.255.255.255
NAT (inside) 1 192.168.1.56 255.255.255.255
NAT (inside) 1 192.168.1.150 255.255.255.255
NAT (inside) 1 192.168.1.200 255.255.255.255
NAT (inside) 1 192.168.2.5 255.255.255.255
NAT (inside) 1 192.168.1.0 255.255.255.0
NAT (inside) 1 192.168.1.96 192.168.1.96
NAT (servers) - access list 0 nat0
NAT (servers) 1 192.168.3.5 255.255.255.255
static (inside, servers) 192.168.1.0 192.168.1.0 netmask 255.255.255.0
static (servers, inside) 192.168.3.5 192.168.3.5 netmask 255.255.255.255
Access-group acl_outside in interface outside
Access-group acl_servers in the servers of the interface
Route outside 0.0.0.0 0.0.0.0 192.168.2.15 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
Enable http server
http 192.168.1.0 255.255.255.0 inside
http 192.168.3.5 255.255.255.255 servers
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto-map dynamic outside_dyn_map 10 the value transform-set ESP-3DES-SHA
Crypto-map dynamic outside_dyn_map 10 set security-association life seconds288000
Crypto-map dynamic outside_dyn_map 10 kilobytes of life together - the association of safety 4608000
Crypto-map dynamic outside_dyn_map 10 the value reverse-road
map Outside_map 10-isakmp ipsec crypto dynamic outside_dyn_map
Outside_map interface card crypto outside
ISAKMP crypto identity hostname
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 65535
preshared authentication
3des encryption
sha hash
Group 2
life 86400
No encryption isakmp nat-traversal
Telnet 192.168.2.0 255.255.255.0 outside
Telnet 192.168.1.0 255.255.255.0 inside
Telnet 192.168.3.0 255.255.255.0 servers
Telnet 192.168.38.0 255.255.255.0 servers
Telnet timeout 5
SSH timeout 5
Console timeout 0
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal vpn group policy
attributes of vpn group policy
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list Local_LAN_Access
allow to NEM
password encrypted qaedah Ipsf4W9G6cGueuSu user name
password encrypted moneef FLlCyoJakDnWMxSQ user name
chayma X7ESmrqNBIo5eQO9 username encrypted password
sanaa2 zHa8FdVVTkIgfomY encrypted password username
sanaa x5fVXsDxboIhq68A encrypted password username
sanaa1 x5fVXsDxboIhq68A encrypted password username
bajel encrypted DygNLmMkXoZQ3.DX privilege 15 password username
daris BgGTY7d1Rfi8P2zH username encrypted password
taiz Ip3HNgc.pYhYGaQT username encrypted password
damt gz1OUfAq9Ro2NJoR encrypted privilege 15 password username
aden MDmCEhcRe64OxrQv username encrypted password
username hodaidah encrypted password of IYcjP/rqPitKHgyc
username yareem encrypted password ctC9wXl2EwdhH2XY
AMMD ZwYsE3.Hs2/vAChB username encrypted password
haja Q25wF61GjmyJRkjS username encrypted password
cisco 3USUcOPFUiMCO4Jk encrypted password username
ibbmr CNnADp0CvQzcjBY5 username encrypted password
IBBR oJNIDNCT0fBV3OSi encrypted password username
ibbr 2Mx3uA4acAbE8UOp encrypted password username
ibbr1 wiq4lRSHUb3geBaN encrypted password username
password username: TORBA C0eUqr.qWxsD5WNj encrypted
username, password shibam xJaTjWRZyXM34ou. encrypted
ibbreef 2Mx3uA4acAbE8UOp encrypted password username
username torbah encrypted password r3IGnotSy1cddNer
thamar 1JatoqUxf3q9ivcu encrypted password username
dhamar pJdo55.oSunKSvIO encrypted password username
main jsQQRH/5GU772TkF encrypted password username
main1 ef7y88xzPo6o9m1E encrypted password username
password username Moussa encrypted OYXnAYHuV80bB0TH
majed 7I3uhzgJNvIwi2qS encrypted password username
lahj qOAZDON5RwD6GbnI encrypted password username
vpn tunnel-group type remote access
VPN tunnel-group general attributes
address vpnpool pool
Group Policy - by default-vpn
Tunnel vpn ipsec-attributes group
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!Hello brother Mohammed.
"my asa5510 to work easy as Server & client vpn at the same time.?
Yes, it can work as a client and a server at the same time.
I have never seen anyone do it but many years of my understanding, I have no reason to think why it may be because the two configurations (client/server) are independent of each other.
Your ASA function as server uses the "DefaultL2LGroup" or it uses standard group policy and tunnel-group are mapped to the remote clients ASA?
Thank you
-
Unable to connect to the Cisco VPN you use native client: El Capitan
I'm unable to connect to the Cisco VPN using native client server Cisco OSX via IPSec. Before the upgrade for connections VPN El Capitan has worked without any problems. VPN uses the shared secret of group. It seems, I get the error "raccoon [2580] ': could not send message vpn_control: Broken pipe ' during the connection."
When I upgraded to El Capitan, VPN connection has stopped working. I tried to do the following:
* connect using the old work VPN connection: without success
Config: Hand [server address, account name],
AUTH settings [shared secret, the Group name].
Advanced [mode to use the passive FTP = TRUE]
errors:
"authd [124]: copy_rights: _server_authorize failed.
"raccoon [2580]: could not send message vpn_control: Broken pipe"
...
* Add new VPN connection using L2TP over IPSec: without success
Config: Hand [server address, account name],
Authentication settings [user authentication: password, identification of the Machine: Shared Secret].
Advanced [send all traffic on the VPN = TRUE]
errsors:
"pppd [2616]: password not found in the system keychain.
"authd [124]: copy_rights: _server_authorize failed.
...
* Add new connection using Cisco via IPSec VPN: without success
Main config: [server address, account name].
AUTH settings [shared secret, the Group name].
Advanced [mode to use the passive FTP = TRUE]
errors:
"authd [124]: copy_rights: _server_authorize failed.
"raccoon [2580]: could not send message vpn_control: Broken pipe"
VPN server is high and does not work and accepts connections, this problem is entirely on the client side.
I. Journal of Console app existing/Legacy VPN connection:
26/03/16 10:24:01, 000 syslogd [40]: sender ASL statistics
26/03/16 10:24:01, nesessionmanager 311 [2112]: NESMLegacySession [VPN_CONN_NAME$: B7816CCC-2D2C-4D6D - 83 D 9-B2C8B6EB8589]: received an order to start SystemUIServer [2346]
26/03/16 10:24:01, nesessionmanager 311 [2112]: NESMLegacySession [VPN_CONN_NAME$: B7816CCC-2D2C-4D6D - 83 D 9-B2C8B6EB8589]: changed to connecting status
26/03/16 10:24:01, nesessionmanager 313 [2112]: IPSec to connect to the server $VPN_SERVER_IP
26/03/16 10:24:01, 316 nesessionmanager [2112]: phase 1 of the IPSec from.
26/03/16 10:24:01, racoon 338 [2580]: agreed to the takeover of vpn connection.
26/03/16 10:24:01, racoon 338 [2580]: agreed to the takeover of vpn connection.
26/03/16 10:24:01, racoon 339 [2580]: IPSec to connect to the server $VPN_SERVER_IP
26/03/16 10:24:01, racoon 339 [2580]: IPSec to connect to the server $VPN_SERVER_IP
26/03/16 10:24:01, racoon 339 [2580]: connection.
26/03/16 10:24:01, racoon 339 [2580]: IPSec Phase 1 started (initiated by me).
26/03/16 10:24:01, racoon 339 [2580]: IPSec Phase 1 started (initiated by me).
26/03/16 10:24:01, racoon 349 [2580]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).
26/03/16 10:24:01, racoon 350 [2580]: > > > > > status of phase change = Phase 1 began by us
26/03/16 10:24:01, racoon 350 [2580]: > > > > > status of phase change = Phase 1 began by us
26/03/16 10:24:01, racoon 381 [2580]: no message must be encrypted, 0x14a1, side 0 status
26/03/16 10:24:01, racoon 381 [2580]: no message must be encrypted, 0x14a1, side 0 status
26/03/16 10:24:01, 381 nesessionmanager [2112]: Controller IPSec: IKE FAILED. phase 2, assert 0
26/03/16 10:24:01, 381 nesessionmanager [2112]: Controller IPSec: retry the aggressive mode IPSec with DH group 2
26/03/16 10:24:01, nesessionmanager 404 [2112]: phase 1 of the IPSec from.
26/03/16 10:24:01, racoon 404 [2580]: IPSec to connect to the server $VPN_SERVER_IP
26/03/16 10:24:01, racoon 404 [2580]: IPSec to connect to the server $VPN_SERVER_IP
26/03/16 10:24:01, racoon 405 [2580]: connection.
26/03/16 10:24:01, racoon 405 [2580]: IPSec Phase 1 started (initiated by me).
26/03/16 10:24:01, racoon 405 [2580]: IPSec Phase 1 started (initiated by me).
26/03/16 10:24:01, 407 raccoon [2580]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).
26/03/16 10:24:01, 407 raccoon [2580]: > > > > > status of phase change = Phase 1 began by us
26/03/16 10:24:01, 407 raccoon [2580]: > > > > > status of phase change = Phase 1 began by us
26/03/16 10:24:01, racoon 436 [2580]: port 62465 anticipated, but 0
26/03/16 10:24:01, racoon 436 [2580]: port 62465 anticipated, but 0
26/03/16 10:24:01, 463 raccoon [2580]: IKEv1 Phase 1 AUTH: success. (Initiator, aggressive-Mode Message 2).
26/03/16 10:24:01, 463 raccoon [2580]: > > > > > status of phase change = Phase 1 began with a peer
26/03/16 10:24:01, 463 raccoon [2580]: > > > > > status of phase change = Phase 1 began with a peer
26/03/16 10:24:01, 463 raccoon [2580]: IKE Packet: receive a success. (Initiator, Aggressive Mode 2 message).
26/03/16 10:24:01, 463 raccoon [2580]: initiating IKEv1 Phase 1: success. (Initiator, aggressive Mode).
26/03/16 10:24:01, 463 raccoon [2580]: IKE Packet: forward the success. (Initiator, Aggressive Mode 3 message).
26/03/16 10:24:01, 463 raccoon [2580]: IPSec Phase 1 established (initiated by me).
26/03/16 10:24:01, 463 raccoon [2580]: IPSec Phase 1 established (initiated by me).
26/03/16 10:24:01, 484 raccoon [2580]: IPSec Extended requested authentication.
26/03/16 10:24:01, 484 raccoon [2580]: IPSec Extended requested authentication.
26/03/16 10:24:01, nesessionmanager 485 [2112]: IPSec asking extended authentication.
[26/03/16 10:24:01, 494 nesessionmanager [2112]: NESMLegacySession[$VPN-CONN-NAME:B7816CCC-2D2C-4D6D-83D9-B2C8B6EB8589]: status changed by disconnecting
26/03/16 10:24:01, 495 nesessionmanager [2112]: IPSec disconnection from the server $VPN_SERVER_IP
26/03/16 10:24:01, racoon 495 [2580]: IPSec disconnection from the server $VPN_SERVER_IP
26/03/16 10:24:01, racoon 495 [2580]: IPSec disconnection from the server $VPN_SERVER_IP
26/03/16 10:24:01, racoon 495 [2580]: IKE Packet: forward the success. (Information message).
26/03/16 10:24:01, racoon 495 [2580]: IKEv1-Information Notice: pass success. (Delete the ISAKMP Security Association).
26/03/16 10:24:01, racoon 495 [2580]: could not send message vpn_control: Broken pipe
26/03/16 10:24:01, racoon 495 [2580]: could not send message vpn_control: Broken pipe
[26/03/16 10:24:01, 496 nesessionmanager [2112]: NESMLegacySession[$VPN-CONN-NAME:B7816CCC-2D2C-4D6D-83D9-B2C8B6EB8589]: status changed to offline, last stop reason no
26/03/16 10:24:01, racoon 496 [2580]: glob found no match for the path "/ var/run/racoon/*.conf".
26/03/16 10:24:01, racoon 496 [2580]: glob found no match for the path "/ var/run/racoon/*.conf".
26/03/16 10:24:01, racoon 496 [2580]: IPSec disconnection from the server $VPN_SERVER_IP
26/03/16 10:24:01, racoon 496 [2580]: IPSec disconnection from the server $VPN_SERVER_IP
$VPN_SERVER_IP
II. new VPN connection using L2TP over IPSec Console app log:
26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetFillColorWithColor: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetStrokeColorWithColor: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetCompositeOperation: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetCompositeOperation: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextFillRects: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetCompositeOperation: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextClipToRect: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetShouldSmoothFonts: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetFontAntialiasingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetDefaultUserSpaceToDeviceSpaceTransform: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextConcatCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextDrawImages: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetShouldSmoothFonts: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetDefaultUserSpaceToDeviceSpaceTransform: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, com.apple.preference.network.remoteservice [2539 295]: CGContextConcatCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextDrawImages: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetDefaultUserSpaceToDeviceSpaceTransform: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, com.apple.preference.network.remoteservice [2539 295]: CGContextConcatCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextDrawImages: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.
26/03/16 10:37:28, [2539 339] com.apple.preference.network.remoteservice: error in CoreDragRemoveTrackingHandler:-1856
26/03/16 10:37:28, [2539 339] com.apple.preference.network.remoteservice: error in CoreDragRemoveReceiveHandler:-1856
26/03/16 10:37:28, com.apple.xpc.launchd [1 393]: (com.apple.SystemUIServer.agent [2346]) Service was released due to the signal: Broken pipe: 13
26/03/16 10:37:28, Spotlight 461 [459]: spot: logging agent
26/03/16 10:37:28, [2539 487] com.apple.preference.network.remoteservice: service - area of the one error ERROR = NEConfigurationErrorDomain Code = 9 "configuration is unchanged" UserInfo = {NSLocalizedDescription = configuration is unchanged}
26/03/16 10:37:28, [2539 487] com.apple.preference.network.remoteservice: service - area of the one error ERROR = NEConfigurationErrorDomain Code = 9 "configuration is unchanged" UserInfo = {NSLocalizedDescription = configuration is unchanged}
26/03/16 10:37:28, nesessionmanager 519 [2112]: NESMLegacySession [VPN_CONN_NAME$: 04c 10954-16 b 2 - 40BB - B3F1 - 9288F968029E]: received an order to start com.apple.preference.network.re [2539]
26/03/16 10:37:28, nesessionmanager 519 [2112]: NESMLegacySession [VPN_CONN_NAME$: 04c 10954-16 b 2 - 40BB - B3F1 - 9288F968029E]: changed to connecting status
26/03/16 10:37:28, com.apple.SecurityServer [75 536]: rules of problem opening the file "/ etc/authorization ': no such file or directory
26/03/16 10:37:28, com.apple.SecurityServer [75 536]: sandbox has denied authorizing the right "system.keychain.modify" customer "/ usr/libexec/nehelper" [184]
26/03/16 10:37:28, 536 pppd [2616]: NetworkExtension is the controller
26/03/16 10:37:28, 538 pppd [2616]: NetworkExtension is the controller
26/03/16 10:37:28, nehelper 540 [184]: 10954-16 b 2 - 40BB - B3F1 04c - 9288F968029E: cannot copy content, returned SecKeychainItemCopyContent user interaction is not allowed.
26/03/16 10:37:28, nehelper 540 [184]: 10954-16 b 2 - 40BB - B3F1 04c - 9288F968029E: SecKeychainItemFreeContent returned the user interaction is not allowed.
26/03/16 10:37:28, 570 pppd [2616]: password not found in the system keychain
26/03/16 10:37:28, 572 pppd [2616]: publish_entry SCDSet() failed: success!
26/03/16 10:37:28, 573 pppd [2616]: publish_entry SCDSet() failed: success!
26/03/16 10:37:28, 573 pppd [2616]: pppd 2.4.2 (Apple version 809.40.5) started by $VPN_SERVER_USER, uid 501
26/03/16 10:37:28, SystemUIServer 620 [2615]: [BluetoothHIDDeviceController] EventServiceConnectedCallback
26/03/16 10:37:28, SystemUIServer 620 [2615]: [BluetoothHIDDeviceController] EventServiceDisconnectedCallback
26/03/16 10:37:28, authd 720 [124]: copy_rights: _server_authorize failed
26/03/16 10:37:28, sandboxd 748 [120]: nehelper (184) ([184]) refuse the authorization-right-get system.keychain.modify
III. New connection of Cisco VPN through IPSec Console app log:
26/03/16 10:18:26, 917 WindowServer [172]: _CGXRemoveWindowFromWindowMovementGroup: 0x10d of window is not attached to the window 0x10f
26/03/16 10:19:43, 975 WindowServer [172]: _CGXRemoveWindowFromWindowMovementGroup: 0x10d of window is not attached to the window 0x10f
[26/03/16 10:19:56 nesessionmanager 265 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: received an order to start SystemUIServer [2346]
[26/03/16 10:19:56 nesessionmanager 265 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: changed to connecting status
26/03/16 10:19:56, nesessionmanager 267 [2112]: IPSec to connect to the server $VPN_SERVER_IP
26/03/16 10:19:56, nesessionmanager 270 [2112]: phase 1 of the IPSec from.
26/03/16 10:19:56, authd 284 [124]: copy_rights: _server_authorize failed
26/03/16 10:19:56, 295 raccoon [2576]: agreed to the takeover of vpn connection.
26/03/16 10:19:56, 295 raccoon [2576]: agreed to the takeover of vpn connection.
26/03/16 10:19:56, 295 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP
26/03/16 10:19:56, 295 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP
26/03/16 10:19:56, racoon 296 [2576]: connection.
26/03/16 10:19:56, racoon 296 [2576]: IPSec Phase 1 started (initiated by me).
26/03/16 10:19:56, racoon 296 [2576]: IPSec Phase 1 started (initiated by me).
26/03/16 10:19:56, racoon 308 [2576]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).
26/03/16 10:19:56, racoon 308 [2576]: > > > > > status of phase change = Phase 1 began by us
26/03/16 10:19:56, racoon 308 [2576]: > > > > > status of phase change = Phase 1 began by us
26/03/16 10:19:56, 352 raccoon [2576]: no message must be encrypted, 0x14a1, side 0 status
26/03/16 10:19:56, 352 raccoon [2576]: no message must be encrypted, 0x14a1, side 0 status
26/03/16 10:19:56, nesessionmanager 352 [2112]: Controller IPSec: IKE FAILED. phase 2, assert 0
26/03/16 10:19:56, nesessionmanager 353 [2112]: Controller IPSec: retry the aggressive mode IPSec with DH group 2
26/03/16 10:19:56, nesessionmanager 373 [2112]: phase 1 of the IPSec from.
26/03/16 10:19:56, 374 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP
26/03/16 10:19:56, 374 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP
26/03/16 10:19:56, 374 raccoon [2576]: connection.
26/03/16 10:19:56, 374 raccoon [2576]: IPSec Phase 1 started (initiated by me).
26/03/16 10:19:56, 374 raccoon [2576]: IPSec Phase 1 started (initiated by me).
26/03/16 10:19:56, racoon 376 [2576]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).
26/03/16 10:19:56, racoon 376 [2576]: > > > > > status of phase change = Phase 1 began by us
26/03/16 10:19:56, racoon 376 [2576]: > > > > > status of phase change = Phase 1 began by us
26/03/16 10:19:56, racoon 404 [2576]: port 62465 anticipated, but 0
26/03/16 10:19:56, racoon 404 [2576]: port 62465 anticipated, but 0
26/03/16 10:19:56, racoon 432 [2576]: IKEv1 Phase 1 AUTH: success. (Initiator, aggressive-Mode Message 2).
26/03/16 10:19:56, racoon 432 [2576]: > > > > > status of phase change = Phase 1 began with a peer
26/03/16 10:19:56, racoon 432 [2576]: > > > > > status of phase change = Phase 1 began with a peer
26/03/16 10:19:56, racoon 432 [2576]: IKE Packet: receive a success. (Initiator, Aggressive Mode 2 message).
26/03/16 10:19:56, racoon 432 [2576]: initiating IKEv1 Phase 1: success. (Initiator, aggressive Mode).
26/03/16 10:19:56, racoon 432 [2576]: IKE Packet: forward the success. (Initiator, Aggressive Mode 3 message).
26/03/16 10:19:56, 433 raccoon [2576]: IPSec Phase 1 established (initiated by me).
26/03/16 10:19:56, 433 raccoon [2576]: IPSec Phase 1 established (initiated by me).
26/03/16 10:19:56, racoon 453 [2576]: IPSec Extended requested authentication.
26/03/16 10:19:56, racoon 453 [2576]: IPSec Extended requested authentication.
26/03/16 10:19:56, 454 nesessionmanager [2112]: IPSec asking extended authentication.
[26/03/16 10:19:56, nesessionmanager 464 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: status changed by disconnecting
26/03/16 10:19:56, nesessionmanager 464 [2112]: IPSec disconnection from the server $VPN_SERVER_IP
26/03/16 10:19:56, racoon 465 [2576]: IPSec disconnection from the server $VPN_SERVER_IP
26/03/16 10:19:56, racoon 465 [2576]: IPSec disconnection from the server $VPN_SERVER_IP
26/03/16 10:19:56, racoon 465 [2576]: IKE Packet: forward the success. (Information message).
26/03/16 10:19:56, racoon 465 [2576]: IKEv1-Information Notice: pass success. (Delete the ISAKMP Security Association).
26/03/16 10:19:56, racoon 465 [2576]: could not send message vpn_control: Broken pipe
26/03/16 10:19:56, racoon 465 [2576]: could not send message vpn_control: Broken pipe
[26/03/16 10:19:56, nesessionmanager 465 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: status changed to offline, last stop reason no
26/03/16 10:19:56, 466 raccoon [2576]: glob found no match for the path "/ var/run/racoon/*.conf".
26/03/16 10:19:56, 466 raccoon [2576]: glob found no match for the path "/ var/run/racoon/*.conf".
26/03/16 10:19:56, 466 raccoon [2576]: IPSec disconnection from the server $VPN_SERVER_IP
26/03/16 10:19:56, 466 raccoon [2576]: IPSec disconnection from the server $VPN_SERVER_IP
It seems that I solved the problem, but I'm not sure it helped.
After restart of the operating system, the two connections: old and new Cisco via IPSec connection, began to work.
-
ASA VPN server and vpn client router 871
Hi all
I have ASA 5510 as simple VPN server and 871 router as simple VPN client. I want to have the user ID and permanent password on 871 and not to re - enter username and password since 871 uses dynamic IP address and every time I have to ' cry ipsec client ezvpn xauth "and type user name and password.
any suggestions would be much appreciated.
Thank you
Alex
Do "crypto ipsec client ezvpn show ' on 871, does say:
...
Save password: refused
...
ezVPN server dictates the client if it can automatically connect with saved password.
Set "enable password storage" under the group policy on the ASA.
Kind regards
Roman
Maybe you are looking for
-
How do I rearrange the photos in my library to iCloud
Although the total number of photos on my Mac Pro disagreed with the iCloud library, they are not held in the clouds to match items on my Mac Pro. As a result, all my devices reflect the iCloud library rather than my Mac Pro. How can I get my devic
-
Aspire V5 - 471G just updated Windows 10 Aniversary Edition need help with Audio driver
I have problem driver Got on my v5 - 471 g ive got everthing operational with the 8.1 except the audio driver windows driver Help me!! BTW my laptop has been upgraded to windows 7 and if you can link me to a page of 10 full for the Acer Aspire V5 win
-
I deleted my Recycle Bin. How can I get that back?
I deleted my Recycle Bin. How can I get that back? Pat
-
Do not download via windows update
I tried to upgrade my computer laptop windows 7 to windows using windows update 10. The download began, but she kept at 0%. I tried to use GetWindows10 the exe for manual upgrade, but it did not work as well. Is there a solution for this problem? Tha
-
Each year, it's my job of burning files closed on DVD or USB keys and store them offsite. I get two error messeges on several of the issues an error 1) reads "file names would be long for the destination folder. You can shorten the file name and try