SA40-702 satellite: startup messages
Hello
Until recently, I experienced no problem with my satellite SA40-702. However, while starting I started getting the following messages, which appear before the Windows XP best wishes...
PXE - E61
Media Test Failure - Check the cable of
PXE - M0F
Exit Intel Boot Agent
While no obvious problems occur while using the machine, its obvious that these messages should not be appearing. Someone had no previous experience of these message?
Any help/advice gratefully received.
Concerning
Peter.
Hi Peter,.
The PXE - E61 message ususally indicates the laptop tries to start from a LAN attached rather than the hard drive or the CD source.
First check the boot order in the BIOS (press and hold F12 for the market) and make sure that your boot order has your hard drive as first or second device in the list before the connection to the local network.
If it is already defined in this way, then it is likely that your hard drive is corrupt because the system can't find the boot sector (or can't read).
I presume that you can boot from the CD (since you say that you tried to reinstall XP. Did you use the recovery discs for your laptop or a Microsoft XP disk?
Kind regards
Tags: Toshiba
Similar Questions
-
SA40-702. Does not start, missing file...
Hello
I have a series SA40-702 Satellite. I had the laptop for about 18 months and until recently had no problems with it.
While on the Internet one day, the laptop has decided to lock up & then close on me, I'm sure that, it displays a message on the execution of a physical memory dump, anyway it closes I started in safemode, performed an analysis of drive & off frag & all appeared to be well again for about a week. He then decided to do it again, but this time he wont even go into safe mode. It displays a message - Impossible start because the following file is missing or corrupt " \Windows\System\vgaoem.fon ."
I really don't want to have to do a full recovery on this because I have a lot of important information about the hard drive I need.Can someone tell me if its possible to load this file back to laptop...?
Thanks in advance, & apologies if it's a bit lengthy...
Gazza...
Hello
This file which you will find under C:\i386. Try to copy this file to the right place (C:\windows\system).
Good bye
-
SA40 has no startup options and does not load Windows
Hello everyone
I just met my first problems with my SA40-702. I got it about 2 years and everything was fine.
The machine will not start is no longer in Windows. He's sitting there for hours with the screen of boot of windows XP, the bar of scroll nothing happens. I tried to access the CD/DVD drive to reinstall windows, but I can't boot from it!
I have had so much try 'C' nothing happens.
I tried "F12" nothing happens.
I tried several copies of windows and the boot disks, but there is no success.
I was in the BIOS and removed the password so it now reads "unregistered" I am unable to change the menu boot options. All that I can change it is time and the password.
Any help on changing the options of startup, or as to why the machine will not let me choose the CD as boot device would be appreciated.
Infact I can't choose ANY boot device.
As far as windows goes all start attempts including safe mode etc do not work. They just plant rather then wait eternally for restart.
I hope someone can help!
Thank you
RichardHello Richard
Usually, if the supervisor password is set, you can have this kind of problems and you will not be able to enter the BIOS settings. I put t really know if someone put the supervisor password and this way I can't help you.
You are the owner of this device or using it in your business?
-
Hi all
I encountered this problem (I don't know if I can call it a problem), with my Z2, when I turn it on, then next turn, or when you restart the phone, once it has finished up the boot sequence, it shows me in the middle of the screen a message saying: powerful communications, your messages are changing... and another... and inside text , it makes me enter my phone number with country code... and hit ok... but it looks about 6 times, hit ok for six times before it disappears! Thank you!
Start safe mode and let us know if you encounter the same startup message
http://talk.sonymobile.com/T5/FAQ/How-to-boot-your-phone-into-safe-mode/m-p/348008#U348008
If you do, remove the SIM card and try again.
-
Files that cannot be found are buzixu.dll and grfamsg.dll. The operating system is vista.
Thank you.
* original title - Hi, I get dll error at startup messages, slow down my computer. Does anyone have ideas how they could be fixed. Thank you very much.*
Hello
Google who provides virtually no information that suggests it might be the malicious program or a start remains for her entry search
Download update and scan with the free version of malwarebytes anti-malware
http://www.Malwarebytes.org/MBAM.php
You can also download and run rkill to stop the process of problem before you download and scan with malwarebytes
http://www.bleepingcomputer.com/download/anti-virus/rkill
If it does not remove the problem and or work correctly in normal mode do work above in safe mode with networking
Windows Vista
Using the F8 method:
- Restart your computer.
- When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
- Select the Safe Mode with networking with the arrow keys.
- Then press enter on your keyboard to start mode without failure of Vista.
- To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
- Do whatever tasks you need and when you are done, reboot to return to normal mode.
If the error persists after scanning use this program to out startup
This utility, Autoruns for Windows, which has a knowledge of auto-starting locations of any startup monitor, shows you what programs configured to run at system startup or login and that the entries in the order of processing windows. These programs include those in your startup folder, Run, RunOnce, and other registry keys. You can configure Autoruns to show other locations, including Explorer shell, toolbar extensions, helper objects to the browser, Winlogon notifications, auto and many start-up services even more.
-
Satellite C650 - message from the PXE ROM at startup
My 6 month old Satellite C650 (Windows 7 64-bit) started grippements this afternoon and now will not restart. She gave the following message is displayed after the Toshiba screen:
PXE - MOF: EXIT INTEL PXE ROM
NO BOOT DEVICEI think that there is a "insert the disk and press a key" after that, but I'm away from home and have not all disks (not sure if there are home either!). So I tried a few off/ons and now does not go as far as the Toshiba screen.
At a loss - nightmare!
Obviously HDD is not recognized correctly, but the question is why.
It's new model of laptop, and you should contact Toshiba service as soon as possible.Addresses and phone numbers, you will find under http://eu.computers.toshiba-europe.com > support & downloads > find an ASP.
-
BSOD - 0x000000ed Unmountable Boot Volume on satellite error message
Hi guys,.
laptop was dropped and I now get the blue screen with this message at startup "stop: 0x000000ed unmountable boot volume.
I read in some sites 'recover using xp disk', my laptop was bought with xp was preinstalled and I don't have a recovery disk.(1) can anyone identify the problem?
(2) a recovery disk help?
(3) if so where can I get one?Thank you
Jim
Hello
I agree with Guybrush. The error seems to be related to the boot file system is defective and new resettlement could help.
As we have already mentioned, the Toshiba Recovery CD could be controlled using the adresse_web above.
If you are owner of an old series of laptop then the recovery CD could be ordered in the local ASP.But generally, you can use a Microsoft operating system CD too.
You could install windows using this CD and all Toshiba drivers can be downloaded from the Toshiba driver page.Concerning
-
L50 - B - creation of recovery - satellite error message
Hello
It's my first visit so I don't know if my son was treated, for this, my apologies.
For several days, I am in possession of the laptop L50 - B Satellite. For security, I want to do a recovery media on a USB key with the Toshiba Recovery Media Creator program. After a while, I get a message that there is a difference between the path of the source in Z:\Recovery\install25.swm files and destination path E:\ZZImages\install25.swm,errorcode 02016E-3 c-00000000.
Is there a solution?Thank you
As far as I know that there is a sort of magic bullet. Either it works or not. Some kind of change is not possible.
Try again please and let us know if the same error recurs.
-
Satellite A100 - message: Toshiba Power Saver already started
When I turn on with power supply connected, I get a false error message that says 'Toshiba Power Saver already begun'.
How can I get rid of this message permanently?Hello
I guess that the Toshiba power saver trying to load twice.
Akuma s suggestion should work.
Once the energy saver has been uninstalled, all entries that control energy saver should be removed too.
After this, reinstall the new energy saverThe alternative might be disables a power saver in msconfig.
To ensure that the access the msconfig (in RUN type msconfig) and remove the mark of an energy intake that you might find in the Startup tab.
Then restart the laptop and check if it worked -
Satellite M40: message: can not play because the DVD decoder is not installed
not serious... I am back... I did a little reading and tried to read another cd in the drive and the message came to say "can't play because the dvd decoder is not installed, so I guess that's the problem because I have a recovery * DVD *.» Anyone know where I can find a dvd for a Satellite M40 decoder?
> can't play because the dvd decoder is not installed
This message appears if you want to play DVD movies with an application like Windows Media Player that has no (plug-in) installed DVD decoder.
Usually the DVD can be played with special programs like WinDVD or PowerDVD for example!But this DVD decoder has nothing to do with the Toshiba Recovery DVD and the fact your new DVD Player cannot read the recovery DVDs.
-
Satellite C660 - message: disk HARD Smart predict service failures - drive check
Hello
I'm new on this site and need some advice.
I have a Satellite C660 laptop and when I recently turned it on I got this message... HARD drive has a clever feature on failures to predict, check the drive.
I did a HARD drive recovery but still getting the same message.
Do I have to buy a new HARD drive and if so where is the best place to buy a.I live in regional WA.
Any advice would be much appreciated.
Thank you
AngelHello
This looks to drive HARD going wrong and in this case the Get procedure isn't a real solution.
I think you need to replace the HARD drive in order to solve this problem.The laptop supports version 2.5 SATA HDD and I think you should find some good deals online in your area.
By the way: after replacing HARD drive, you should be able to recover the laptop using the recovery disk.
-
hot to turn off Java after the startup message
Hello world
I know it's a bit old, but I couldn't find an answer to it, or maybe I searched the wrong topic. After the reboot, I still get this warning window saying "to use the"java"command line tool, you need to install a JDK.
I ElCapitan and recommended Java installed since Mavericks version, but the message never goes away. The used warning window is displayed only after restart, but now he appears randomly during normal use of the laptop.Please help me to get rid of
You have software that requires the Java command line tool? It is only in the JDK you will find Oracle's Web site.
Check your/Library/LauchAgents and /LibraryLaunchDaemons for startup like facebook or similar items. Also, check your user settings (users & groups) under your Log - In for Autostart-software items after the connection.
-
Weird startup message "fixed disk:" X 240
Hello
Today, I went back to my holiday work, and when I turned on my X 240, I saw this start message:
http://i.imgur.com/0DDFIZe.jpg
Then I pressed Enter and it just booted normally. What it means? Is it possible that she has been manipulated?
Should I worry about this?
Thank you!
It is the diagnostic screen that you get, disable boot in the bios then go to the Startup tab and look for the boot if Mode so-called [diagnosis], then replace it with [fast] and then go to restart exit save changes that must disable the diagnostic boot and you should get only thinkpad splash screen and then start windows
-
Satellite M60 - message: graphic driver works correctly
Hello
I own the Satellite M60 laptop and have problems with the graphics card ATI X 700.
Often, I get the message that my graphics driver does not work properly.
When this happens, changing resolution displays at 720 * 640 I think and I have to restart my pc.What did I try?
I installed a new windows system, I tried to make a new absolutely clean driver to install.But nothing helped.
Someone at - it an idea, what I have to do?concerning
> Often, I get the message, that my graphics driver doesn t work properly.
> In this case, the change in resolution display 720 * 640 I think and I have to restart my pc
Sounds more like a hardware malfunction as software delivers what dilute you?
To me, it seems that the graphics chip would cause this issue may be due to a higher internal temperature? ?:|Have you noticed a higher temperature while this problem appear?
-
P 500 Workstation startup message
On startup, I get the following message:
«Wait REG bit timeout, send the information of MTN/SN to eSIO fail»
Apparently not creat any problem outside of slow start-up time.
Serial number: XXXXXXXX
Product number: 30A7CTO1WW
BIOS: A4KT80AUS
My firmware is up to date?
(Mod edit: series removed from public display for your safety)
Odd. Try to Flash up to the 87A and see if it goes away. http://support.Lenovo.com/us/en/downloads/DS101230
Let us know your results and we'll go from there if other measures are needed.
Maybe you are looking for
-
After the upgrade to new firefox, I now have a rectangle across my my screen under my search bar. It is featured with a more dark blue on top and various colors about 1/2 down, measuring about 1/2 inch in depth. How can I remove it?
-
Satellite P10 - laptop off suddenly during application
My Satellite P10 has a problem for about 1 month. In many applications (for example games) he died suddenly, without message or similar warning. Is it possible, that it's getting hot?It worked without any problems for over a year half! Could it, that
-
Display drivers crashing when connecting Skype with a new monitor BenQ
Hello, so I just got a new BenQ XL2411Z monitor and for some reason, when I connect on Skype, display drivers crash 9/10 times. If I use the old monitor and launch Skype everything works normally, but display runnning drivers the new BenQ it will cra
-
Transition from XP to Windows 7, can't locate the little information?
I'm not very savvy of computer programming. As indicated, I have Windows XP 2002, service pack 3. Follow the instructions in Microsoft XP to find the number of "bits: under the property system.» Unable to find these. Also, should I move from XP to 7?
-
I installed the printer and prints OK but the scan and save to PC is not currently available. HP Director is not displayed. I need to download and install it? Did I miss something?