SAMSUNG SSD Pro 840 died after two days of Thinkpad Yoga

Similar Questions

• Still slow after Samsung SSD Pro 850

  I recently installed Samsung SSD 850 pro on my mbp 2012. There is no significant difference in its speed before and after. Application of test of speed magic Black Watch reading and writing speeds both somewhere between 40 - 60 MB/s. If disappointing! I'm not a tech guy but there might be people out there who have experienced this problem and have regained hope. If you know a solution please share.

  This is the Office Mac Pro forum. I asked that your post moved to the forum of laptop MacBook Pro or another appropriate forum.

• T7500 and Samsung SSD evo 840: AHCI is not enabled!

  Hello

  I have just pluged a Samsung SSD 840 evo on a T7500 (the sata plug 0 of the motherboard) and did a fresh install of Windows 7 64-bit.
  Everything seems fine, that I can write this post on my PC upgraded, but I'm a little frustrated, as Samsung magician, SSD supplied management software, tells me that the AHCI is not enabled, and "it is impossible to detect the SATA interface. Therefore, I will not have the installation of the SSD... I checked the windows regestry and key "msahci' as the value 0 for 'start', which seems OK.

  I missed something? Any help would be much apreciated!

  Arnaud

  Hi Agaillot,

  You should be able to see the controller mode in the Intel RST utility, including the speed of the port. What do you see here?

• SAMSUNG SSD of 840 EVO and the compatibility of the Inspiron 17 5748

  Does anyone know how to get a Samsung SSD to work in an Inspiron 5748? A BIOS update would be useful?

  There is absolutely no problem regarding the SSD compatibility, some very old systems here are held in SSD Samsung and Dell used their Samsung SSD OEM partner.

  I strongly suggest a clean format and install (remove all clear them partitions beforehand or course the reader) it could be a matter of hunting wild goose if you perform a new installation, and it will be difficult to diagnose.

  Wizard software should have told you regarding the State of health of the reader? If it is GOOD then its most likely your electronics semi-fresh install it here is the root cause.

• T440s kills 840 Samsung SSD pro

  Hi all

  I have a T440s new, bought with HARD drive. That I wanted to use a reliable SSD, I bought a Samsung 840 pro, I already running in another system. That's when the problems started. In a German Forum several users report similar problems, so I just wanted to give a summary here, so that perhaps the international community can help. I consider myself as being an experienced user, built the various PC systems in recent years and currently have a desktop running with Samsung 840 pro system. Here are the details:

  I installed Windows 8.1 (several times, first clone HARD drive and later after recurring problems, clean full install win DVDs of 8.1), value UEFI Bios only + Intel Quick start disabled before installation.

  The question now is with the SSD I get constant HDD (visible in EventViewer) mistakes, while usually after a few hours of operation, the operating system is damaged to the point that it cannot start more. I should mention that the same system is running stable with the original HARD disk. First I thought that it is a faulty SSD and I replaced it by Samsung. However, with the new SSD replaced I am facing the same problems. Earlier this year, I have corrected a problem on a desktop with 840 pro where symptoms were similar. In the case of a desktop system, the issue could be fixed by replacing the SATA cable (which is obviously not an option on the T440s).

  And Yes, I use the latest firmware SSD, the BIOS update, the drivers of Lenovo. Now, the problem is that I do not seem to be the only one with these problems. Other users in similar problems Thinkpad German forum report not only on Windows systems, but also on Linux installations (we even got the motherboard replaced by Lenovo and yet, it does not solve the problem).

  I contacted Lenovo support and they told me that they support only of original Lenovo SSD. I must say that I am really disappointed that my new system from a renowned manufacturer constantly does not work with one of the most widely used SSD. Currently, some users in the report of the German forum they have better luck with Samsung EVO SSD. However, after this experience, I really lost confidence in the T440s. If the design should have problems with Sata 3, I don't know if I can trust this laptop in a business environment.

  Comments/suggestions very welcome.

  Kind regards

  Frank

  PS: Here is a reference (at least two other users reporting this issue in this forum, here, in German, however)

  http://forums.Lenovo.com/T5/T4-T5-und-neuere-T-serie/Lenovo-T440s-Samsung-840-Pro/m-p/1297091#M1562

  
  

• Windows 8 - clean install on a Samsung SSD of 840 Evo

  Hello

  I'm trying to do a clean install of Windows 8 on my new Samsung 840 Evo SSD - but when I go through the process of installing Windows 8 will detect not the hard drive - and wonder for drivers?
  I'm not sure what it does cause here I can't find the drivers for this SSD drive
  I read something about changing the settings of my RAID BIOS to AHCI - but not quite sure what that means...
  Hopeing someone can talk me through this

  Hello

  Just a short note to tell you I had this work - I was just using the samsungs migration software - something that I had already tried before but without success - difference this time is that instead of connect the SSD drive via the usb port 3 as they suggest (for the initial migration), I connected directly to the pc.
  So its all working now!
  Bravo and thank you again for your help

• Yoga 2 Pro Bluetooth died after Windows update 10

  I've updated all my drivers after the last Windows 10 Pro update. Everything worked fine before the update, but after the restart, nada. I tried to roll back the bluetooth driver, but the system wouldn't let me. In Device Manager, the properties of the driver bluetooth (Version 19.11.1639.649) says:

  "This device cannot start. (Code 10)

  STATUS_DEVICE_POWER_FAILURE ".

  Suggestions?

  Restore point did not work, but I went to http://support.lenovo.com/us/en/products/Laptops-and-netbooks/Yoga-Series/Yoga-2-Pro-Lenovo/80AY/CTO... and downloaded the exe of the bluetooth driver and installed twice, the second time, I selected repair installation. Repair fix all the missing drivers. Yay!

• Helix 2nd G: ThinkPad Pro keyboard died after standby

  Wait for the Tablet (while being attached to the Keyboard Pro) between standby and resume by pressing the power button, the keyboard stays dead.

  Workaround solutions:

  -Detach the tablet in and attached to the keyboard or

  -Reboot

  BIOS: 1.72

  OS: Windows 10

  Is this a known issue?

  
  

• OfficeJet Pro 6970: HP OfficeJet Pro 6970 offline after 1 day - will not print

  Buy HP OfficeJet teacher last Sunday - put in place the tablecloth as a whistle on my HP Desktop (wired). After a mystery visit to find the WPS PIN code, I had a HP laptop (wireless) installation. looking for a good...

  So my wired computer now impossible to print - it goes through the router. But the laptop is still the impression - so it's printing directly to the printer, and not through the router?

  I had a Canon 2 printerd that (I thought) sucked into the sky high with the radio, but maybe it's the router.

  However, several telephones are connected wirelessly, several other devices work correctly. It is a fairly new router from Verizon.

  

  Welcome to the community of HP @WilliamPeck

  I stumbled upon your post on the issue of the printer offline and wanted to answer to help with my suggestions. Please see the guide below to resolve this issue. The printer must be brought back online later.

  Before you try the link, make sure that you tried to restart the computer and run the print and Scan of the doctor.

  • Printer is offline (Windows)

  Hit the "accept as Solution" if we reached a solution and the "thumbs up" to say thank you for my help.

  Contact HP:
  Step 1. Open the link: www.hp.com/contacthp/
  Step 2. Enter the product number or select Auto detection
  Step 3. Scroll up to "still need help? Fill out the form to select your contact options.
  Step 4. Scroll down and click on: contact HP options - click Get phone number
  File number and phone number appear

• Many BSOD after installing Samsung SSD 840 pro in ThinkPad Lenovo R60

  Have an old Lenovo ThinkPad R60 with screen SD that I won't. After installing the Samsung SSD Pro 840 the BSOD started coming, now every week, the last one on today. I don't see the option to download the dump anywhere file, so I enclose a picture with - maybe - some info.

  Can anyone help?

  Thank you

  okinchi

  

  Not at all surprising that involved C:\WINDOWS\SYSTEM32\DRIVERS\SYMEVENT. Pilot of the SYS Symantec event library.  I remove it and use MSE in its place

  Symantec is a common cause of BSOD.

  
  
  I remove and replace it with Microsoft Security if you are using Windows 7 and if you win 8 or higher, use the built-in Defender.
  http://us.Norton.com/support/kb/web_view.jsp?wv_type=public_web&docURL=20080710133834EN
  http://www.Microsoft.com/security_essentials/

  Use it to Norton 360 http://Symantec.pcperformancetools.com/Norton-360-how-to-uninstall.html 

• my laptop is saying that this copy of windows is not genuinne of these last two days? What will I do

  first of all, I downloaded windows 10 from the Microsoft Web site. After two days I downgrade it because my laptop runs slowly on Windows 10. After decommissioning it saying that this copy of windows is not genuine. Please if someone tells me how to get these.

  How to: fix Windows 7 or Windows 8.1 active or true reports after cancellation of Windows 10

• 'the Setup installs devices' worked for two days now...

  recently reformat the hard drive and I'm trying to reinstall windows by using the oem disks that I created after the purchase of this pc. Installation happens to the devices screen and sits there. the system seems to work because I see the "heartbeat" on the screen. The first time that this has happened, I turn it off after two days, and after some research, I discovered that I had left my camera dock connected. The second time, I ran the installation I still have the same problem. It is on this screen yesterday at 06:00. I'm going to run until I get some kind of answer about it.

  Clem:

  After many frustrating attempts, I replaced my hard drive. It was defective. New hard drive and installed it the first time. Hope this helps you.

• optimize the catalog found two days

  I may be in deep Doo - Doo LightRoom here. Any suggestions?

  
  

  Not the latest version of LR - LR 6 to CC but I heard some horror stories about the fix of a few weeks ago so I have not installed it, I'm about 2 months late.

  (1) I saw a post on "automatically write changes into XMP"? I did it.  (the question here #4: 5 Questions to help you make sure that your Photos are safe inside Lightroom )

  (2) I got a new 6 TB external drive for my old images

  (3) in LR, I created a new folder on drive 6 TB then moved the folder of the car 3 TB

  (4) I waited very long for about 22 000 files to move on
  (5) after the passage of all did I quit LR and said he'd do the usual backup
  (6) the backup takes more than 30 minutes, wouldn't quit, I have power drove the MacBook
  (7) back in LR, everything was very slow, just trying to move to a file took forever, the screen display was the number of seconds behind mouse clicks
  (8) again to quit LR and has let it's backup jobs - after two days it is still 'optimize catalog previews.
  

  
  

  I think I have two options:
  (A) wait a little longer (2 days?) to see if the LR backup runs on its own until the end
  (B) bail out and get my LR catalog of before I made #1 above (I have a backup!) don't not #1 the thing with XMP, instead of trying to move 22 000 files do everything at the same time in smaller batches

  
  

  Here is a screenshot with screen notes...  And some close-ups as she was stopped so small

  

  
  

  

  
  

  
  

  • Yes exactly this file, catalog Previews.lrdata Lightroom the move on the desktop, but only after you stop LR leave the monitor activity or stop to the bottom of the computer.
  • The back until done LR is back to the top of the catalog with your most recent work.

  ~ Rohit

• Organize my SSD for first installation / After Effects, your opinions between Mushkin / Samsung PRO 850... ?

  Thank you for taking the time,

  I have i7-5960 x arrives in the mail, it is a huge upgrade for me to sage of the CPU, and I intend to install it on the motherboard ASRock Extreme 4 x 99.

  I have installed ram 64 GB with mono-GPU (Evga overclocked 980Ti) - I also ordered a bolt of lightning ASRock extension adapter to install in one of the PPI.

  with internal Samsung PRO pci 512 m2 will be installed (and hopefully also works!) for my OS/PROGRAMS;

  Now in the light of the information (please do not hesitate to give a few tips if you think that something's going South) above

  I have the options of 3 disks Samsung Pro 850 SSD (1 to) each

  and also Mushkin reactor 1 TB drives coming from another system.

  Now because m2 is expected to be only to win 10/programs installation, I thought I had 3 separate SSD for media (media that I capture) - Render (output) and the Disk Cache

  now I know PRO Samsung SSD are preferred for editing configurations 4 k video, but I also want to save money to change my monitor in the near future, so I want to return

  some of the Samsung SSD if possible.

  I want to ask if I wanted on Raid 0 to increase the speed of 1.5 x times. should I do for media drive, or make it output drive or Cache?

  what player in terms of managing files in Adobe Premiere and AE would benefit more and be more safe if a failure at the top of my head, I think there should be files that I can lose a days work if hds Raid goes down?

  I thought I can keep records of 1 TB of reactor of 2xMushkin in RAID 0 for this player that you would suggest.

  and perhaps just one Samsung drives for others. I'd really love to hear your comments; Even now, I'm sitting on a certain readers, but I want to save money in the long run since Sammy readers are quite expensive.

  Thanks to you ALL

  page Tweakers is a starting point for the advice, but its general advice that may not match your specific needs. some of the information there was written for 7200 rpm disks.

  hackers page says that its important to separate the OS/applications of the media player, so that the windows of standard tasks done constantly in the background is not interrupt reads/writes on the media player when editing. He goes on to say that disk operating system/applications doesn't have to be anything other than an ssd sata. the samsung 950 pro m2 will be only windows boot a bit faster and a little faster, has nothing else once they are open and running of programs.

  scratch disk has several settings for the captured media and rendering of previews. Some people use none and so their installation program does not need a disk separate cache / scratch for first, and they can leave their cache on the disk for the OS/applications. for AE, it will depend on if you have the disk cache. If you are interested in a cache drive, which could be shared with first rendered preview and scratch your files.

  'media' on the page of tinkerers and forums here, almost always refers to camera video files, not video files captured through a map of IO with the first or any other software. If you capture images with a map of IO, there can you want to have a dedicated ssd to it, to make sure that nothing interferes with the disk writes.

  the media cache database files are as creating files for indexing creates to help speed up the playback of files while working with them first. media cache is not the same as zero/capture/preview makes. Bill (forum member) did a lot of tests with disk configurations and also tested leaving media on a sata ssd cache used as disk operating system/applications. He concluded that it makes no difference to performance. so no, there is no need to worry about raid for the first cache files. If you want to use the samsung 950 pro for OS/apps, you can also leave your cache about it. You can even have enough space to use the 950 pro for the cache drive AE and rendered preview files creation too.

  all this is based on the media and what will be done in the timeline, such as screenshots, multi-cam, or preview files. the samsung 950 pro is fast enough to do anything, as long as it fits on the disc. the CT 1 950 pro releasing will see even more people with a configuration to a single disk for everything. other people will be fine with only two ssd sata, one for the OS/apps/cache and other media projects. Some will have more ssd sata or ssd pcie for increasing the speed or the ability to adapt to their specific needs.

• About three weeks ago, I bought a new MacBook Pro, disabled Adobe CS 6 on my old MacBook and re-intalled on my new computer portable DVD with success. I used all my Adobe fine until today. Two days ago, I've updated all my creative suite after receivi

  About three weeks ago, I bought a new MacBook Pro, disabled Adobe CS 6 on my old MacBook and re-intalled on my new computer portable DVD with success. I used all my Adobe fine until today. Two days ago, I've updated all my creative suite after having received an automatic notification. Photoshop will not launch now (everything else is OK). When the Photoshop window it immediately crashes with the message "adding extensions...."  Quick basic routines' but nothing happens and I have to "force stop" window. Advice please?

  reset your preferences: https://forums.adobe.com/thread/375776

  In addition, if you inadvertently "improved" cs6 in the cc version, you use a trial (unless you have purchased a subscription) which will expire in 30 days.