Sat Pro 6100 - black LCD screen

Similar Questions

• RTC & Sat Pro 6100 battery

  Sorry for my bad English.

  If the cmos of laptop battery (I have a sat Pro 6100) is damaged completely, the laptop also ignite?

  Hi Biagio,

  The RTC (or CMOS) battery is installed on the motherboard, and is used to keep the BIOS settings when the laptop is turned off. If the RTC battery is faulty then the date/time and other parameters of the BIOS only be not maintained when the laptop is shut down for a while.

  The normal battery will be affected by the failure of the RTC battery and will always recgarge as usual when the laptop is connected to a power source.

  The RTC battery can be charged by connecting the power supply but leaving the laptop off for about 24 hours. If the date and time is always lost after that the RTC battery should be replaced by an authorized Service Agent Toshiba.

  HTH

  Post edited by: NickyNoogle

• Satellite Pro 6100: black border to the right of the screen

  After a new installation with windows xp when I star tup I have a black border (1.5 cm) to the right of my screen.
  After the beginning and the end of the screen saver, I have a full screen.
  but when my laptop started again I have this black border again.
  I have a satellite Pro 6100.

  Management information
  System
  Model = laptop
  Manufacturer = TOSHIBA
  Serial number = 0000000000
  UUID = ffffffff-ffff-ffff-ffff-ffffffffffff
  BIOS Version = Version 1.90

  OPERATING SYSTEM
  Caption = Microsoft Windows XP Professional
  Version = 5.1.2600 Service Pack 2

  CENTRAL PROCESSING UNIT
  Index = 1
  Manufacturer = GenuineIntel
  Name = Mobile Intel (r) Pentium (r) 4 - M CPU 1.70 GHz
  Version = model 2 Stepping 7
  Max clock speed = 1694
  Socket designation = uFC - PGA Socket

  Display
  Index = 1
  Horizontal resolution = 1024
  Vertical resolution = 768
  Chip Type =
  The RAM size =

  Very strange problem! Can you please tell us more about this problem? I assume that you have installed the OS on your own. Since when you noticed this weird display problem?

  Have you noticed this immediately after installing the OS (without driver)? Did you install the display driver on Toshiba support page?

• Sat Pro 6100: Moving by itself of the mouse

  Hi all
  You have a question about a problem I'm having with my mouse two USB and the joystick on my satellite pro 6100 xp sp2

  The poroblem is that the cursor moves off the screen, either in the top right or bottom left. Tired using laptop without usb mouse same problem, have scanned laptop in case of virus, found nothing. been looking for the web, but only to find that the people who have had this prob is with mouse Sales (Laser or infrared ones)

  I was wondering if it's got time my keyboard replaced in which case this is the problem is, the mouse uses a bit of the keyboard to work.

  Someone at - he encountered this before and could point me in the right direction

  see you soon

  Hello

  Well it s strange. The problem occurs if the joystick is not connected?
  This resembles the function of calibration of joystick or mouse.
  Have you tried to calibrate the joystick?

  Also the same problem occurs if the accupoint mouse trying to calibrate. The mouse cursor moves to 5-10 seconds. Right now you shouldn't t touch the mouse.

  Good bye

• Sat Pro 6100: The orange light blinks

  GDay guys,.

  Thursday, it was the last day of school.
  In the last lesson of the day, I used the laptop to play games (Toshiba Satellite Pro 6100, 1, 6 GHz) when the Bell went. I tried to stop in time, however running in battery mode, she went up to 1 ghz and has been quite slow, closing the game so I immediately turned it off by holding the button for a few seconds.

  I put it in my new computer case belkin which offers a thick foam padding and went home by bus. When I finally got it, I plugged the laptop and tried to boot the system. The screen didn't work for some reason, so I tried the key light several times without success. Reset the computer several times, still nothing. I was wondering if it was the hard drive of the stopping is not correctly earlier this day here but I could always blindly log windows. It me intrigued as to why the screen wasn't on. I presume that a cable was loose so I removed the keyboard and checked the cables on the graphics card. They were fine. Put the keyboard back on and tried to start the laptop.

  The flashing yellow light has shone in its ugly glory. Something was wrong. I left the cell only and got the father, who is an electrical engineer to check on the laptop for all things obvious which could cause this problem. Dad couldn't see anything.

  Before, I read a post on the resettlement of the graphics card can work so I reinstalled the graphics card and tried to boot the system. Still nothing!

  What the hell is happening?

  I read these support forums and find a post on how you can charge the battery, start etc and try it and watnot, but it still fails. When I remove the battery and exit onto the adapter and replace the AC adapter in, a green light that shines above its power light shines. When I put the battery in again, a yellow light shines above the stack, however as soon as I press the power button, everything shuts off and the yellow led shines above the logo of ac power...

  Any ideas as to what may cause this problem and how can I solve this problem?

  -Well done guys!

  Hello

  Littco is right. You must contact the partner in your country. On this way is really not easy to say what can be the problem, but I guess Hat there is a problem with the electronic control gear and you will not be able to repair only. Check it please this page

  http://www.CSD.Toshiba.com/cgi-bin/TAIS/Su/su_gaspLocator.jsp?PF=true

  and there you can find a list of aspic in your country.

  Good bye

• Sat Pro 6100: firmwareupdate for wireless CardBus TI 1410 Lucent ORiNOCO

  Hello

  my laptop is a Toshiba Satellite Pro 6100
  with this wlan card: Wireless: TI 1410 CardBus / Lucent ORiNOCO
  and this firmware:

  Eth1: Material identity 0005:0004:0005:0000
  Eth1: Station identity 001f:0001:0008:000 has
  Eth1: Firmware identified as Lucent/Agere 8.10

  The problem is that the drivers will not work with this firmware.

  eth1: Lucent/Agere firmware does not support manual roaming

  Now, I am looking for a firmware update for this card (I think 8.72 should be the current). The update should work on linux or (if not available for linux) on windows.
  Kind regards.
  Can someone help me that my wlan Runic card with Linux?
  Rico

  Kernel:
  2.6.14 - gentoo-R5

  Hello

  As far as I know that the wireless LAN card is optional on East Unit.
  You upgrade the unit with the wireless network card?
  Well, I put t know you what WLan card, but these cards are compatible

  Wireless LAN Mini PCI Card (2, 4 GHz, 802. 11a / b) PA3236U-1MPC
  Wireless LAN Mini PCI Card (802.11a/b/g) PA3298U-1MPC
  Wireless LAN Mini PCI Card (802. 11 b / g) PA3300U-1MPC

  The drivers for these cards, you will find on the page Web of Toshiba or the Intel Web site. In my opinion, if you use a good card and driver so that all should work properly.

  Good bye

• LJ Pro MFP m127fn: LCD screen control panel is too dark.

  Is there a way to illuminate the LCD screen of the control panel? Thank you.

  Thanks for your reply. To contact the HP Support, I learned that nothing else can be done short of the back of the printer.

  LeftyMike

• Satellite Pro A100-622 lcd screen switch

  Hello

  can anyone tell me where the switch that turns off the display when you close the lid, or sensor or anything that turns the unit off.

  my screen stays on when closed after that I adapted a new Panel lcd, inverter and cable.

  Thank you.

  First of all, check that Windows is configured to do something when the lid is closed. Perhaps, it is set to "do nothing".

  I think it has a magnet near the LCD that triggers a sensor in the base (and possibly the motherboard).

• Sat Pro 6100: Startup takes to long after the BIOS update

  Hello

  I have improved my 6100 to bios 1.90, but now starts, it takes about 1 minute to get the Toshiba screen, and after the beginning of the boot, the system stops.

  Can I somehow downgrading the BIOS on my own?

  Hello

  Downgrade of BIOS is not possible. Service partners just to do this.

• Satellite Pro L300 1AI LCD screen backlight not working not

  Hi all

  I have a Satellite Pro L300 1AI running Windows Vista the computer starts and works fine but the backlight on the screen doesn't seem to work.

  Y at - it none of the Vista settings that can affect this (other than the Fn key command on the keyboard and settings) in Control Panel? Strangely, it seems to have happened since I installed Skype but I don't see how this could possibly affect it.

  Any help is much appreciated...

  Hello

  What s wrong exactly? Brightness screen laptop s is too low?
  Everything you see on the screen as behind a thick fog?

  Well, usually the FL Inverter control the backlight of the screen and if the FL inverter starts to malfunction, so you would get the problem like this.

  There is no alternative to replace this inverter FL.
  It s a small part behind the frame of the screen I think that it s a job for a technician in ASP.

  Welcome them

• SAT Pro 6100 Modem and WLAN problems

  Hi all

  I have a portable SP6100 which had reinstalled WINXP SP2, allows to detect the PCI modem but not install and WLAN installed the drivers but it cannot see all wireless networks. I tried to download and reinstall the latest version of these drivers on the Tosh site and did the MS updates but still no joy. The modem will not install, it says invalid drivers. If removed WLAN drivers, reinstall automatically on reboot (Tosh Wireless LAN Mini PCI Card) but still does not work. Someone had problems with this? See you soon...

  Hello

  First of all, I would like to say a few words on the question of the modem;
  To my knowledge the laptop is equipped with a chip modem Scopio (Agere AC 97)
  You need a XP driver that supports this chips and SP2!

  I also checked the page of the Toshiba driver and found information for Microsoft Windows XP SP2 update.
  It seems that the BIOS should be updated version 1.90 or later!
  In order to check your installed BIOS!

  Now something of WLan:
  It seems that the laptop supports a standard Wi - Fi: 802.11B and WEP encryption.
  If your WLan router has been set at G orto your, you will not be able to see the WLan networks!
  The router must support the 802.11 standards B

  Remember that your wireless network card is compatible with the Wlan router!

  I am owner of 2 laptops. One of the laptop uses a 802.11 has / B card Wlan and my router supports the B/G 802.11 standards.
  A laptop cannot connect to this router because of the different standard.
  Maybe it's the same reason for your problem of s

• Satellite Pro 6100, WXP SP2, once in mode installation ensures the unknown USB

  Hello

  After you install the update in Win XP SP2 on my laptop Toshiba SAT Pro 6100, the following occurs:

  When the laptop wakes from sleep mode, the USB connector is unknown and the communication is lost.

  Who knows the answer to this problem?

  Hello Erjee,
  you just need to install the version of the bios 1.90 or later.

  For other machines with the same problem after installing SP2...
  TE2100 v1.60 or later version
  SATELLITE PRO 6000 v1.60 or later version
  PORTEGE 4000 v2.10 or later version
  TECRA 9000 v1.40 or later version

• Black screen on Sat Pro A10

  Hello

  I have a Sat Pro A10.

  My problem is that my screen is so dark, that I can't see the content (maybe it's the backlight?). However when the computer starts, I can see the login screen of Toshiba fine. I also have the image if normal poster if I close the lid, and then open it. However the screen will stay only normal for a few seconds.

  Anyone have any ideas what is wrong here? Why does the screen work at boot and then deceive you? Is this a hardware or a software problem?

  Any help would be great.

  Hi Alex,

  It sounds like a problem with your inverter FL. You will need to take your laptop to a partner of Service allowed for it to be repaired or replaced.

  Kind regards

• Satellite Pro 6100: screen stays completely white or completely white

  I have a Toshiba Satellite pro 6100 running windows XP with SP2.

  For the last time, when you turn it on, sometimes the screen is totally blank and sometimes she is totally white.

  Must shut down the computer and try to reboot, sometimes several times until the computer starts correctly.

  Could you please tell what it is and how to fix it.

  Your answer will be highly appreciated.
  Thank you.

  Hi, Louis

  I think that we should first find out if the problem is related to the graphics card, for the internal display or on the part of the screen!
  In such cases, it s a good idea to connect the external monitor to the laptop.
  Check if the symptoms appear also on the external monitor.

  If the same thing will happen on the external screen so I guess that the computer laptop s video card is malfunctioning. But if the image appears correctly on the screen then the problem could be linked to the internal LCD display or the small part as FL inverter.

  Check it out

• Satellite PRO U500 - LCD screen size is reduced

  Hi all,

  I have a Toshiba Satellite Pro U500 with one small problem, the size of the LCD screen is reduced. I have a white border to the right and down. The max resolution is 1024 x 768.
  The problem is visible also when I enter the BIOS, so I think that the problem is not Operting System drivers.
  Is there a solution to my problem? I have to send in the audience?

  Thank you for the help
  Giuseppe

  H

  It is really strange, especially if you see the same thing in the BIOS settings?
  Since when did you notice this behavior?
  Do you use pre-installed OS original you got with your laptop?

  Have you done something that may be responsible for the issue described?

  I U500 and default display resolution is 1280 X 800 t, so I understand why you have 1024 X 768 on your U500.