SAT Pro 6100 Modem and WLAN problems

Similar Questions

• Sat Pro 6100: firmwareupdate for wireless CardBus TI 1410 Lucent ORiNOCO

  Hello

  my laptop is a Toshiba Satellite Pro 6100
  with this wlan card: Wireless: TI 1410 CardBus / Lucent ORiNOCO
  and this firmware:

  Eth1: Material identity 0005:0004:0005:0000
  Eth1: Station identity 001f:0001:0008:000 has
  Eth1: Firmware identified as Lucent/Agere 8.10

  The problem is that the drivers will not work with this firmware.

  eth1: Lucent/Agere firmware does not support manual roaming

  Now, I am looking for a firmware update for this card (I think 8.72 should be the current). The update should work on linux or (if not available for linux) on windows.
  Kind regards.
  Can someone help me that my wlan Runic card with Linux?
  Rico

  Kernel:
  2.6.14 - gentoo-R5

  Hello

  As far as I know that the wireless LAN card is optional on East Unit.
  You upgrade the unit with the wireless network card?
  Well, I put t know you what WLan card, but these cards are compatible

  Wireless LAN Mini PCI Card (2, 4 GHz, 802. 11a / b) PA3236U-1MPC
  Wireless LAN Mini PCI Card (802.11a/b/g) PA3298U-1MPC
  Wireless LAN Mini PCI Card (802. 11 b / g) PA3300U-1MPC

  The drivers for these cards, you will find on the page Web of Toshiba or the Intel Web site. In my opinion, if you use a good card and driver so that all should work properly.

  Good bye

• RTC & Sat Pro 6100 battery

  Sorry for my bad English.

  If the cmos of laptop battery (I have a sat Pro 6100) is damaged completely, the laptop also ignite?

  Hi Biagio,

  The RTC (or CMOS) battery is installed on the motherboard, and is used to keep the BIOS settings when the laptop is turned off. If the RTC battery is faulty then the date/time and other parameters of the BIOS only be not maintained when the laptop is shut down for a while.

  The normal battery will be affected by the failure of the RTC battery and will always recgarge as usual when the laptop is connected to a power source.

  The RTC battery can be charged by connecting the power supply but leaving the laptop off for about 24 hours. If the date and time is always lost after that the RTC battery should be replaced by an authorized Service Agent Toshiba.

  HTH

  Post edited by: NickyNoogle

• Satellite Pro 6100 - Question on WLAN adapt and mac address

  I bought a second hand of Satellite Pro 6100. It has a WiFi adapter. It is where and how do I know the macadress of the adapter?

  Thank you.

  Hello

  If you are sure that this laptop was equipped with the Wlan card, and then the MAC address can be easily discovered 100%.
  You must start the console with the command: * CMD *.

  Then use the command: * ipconfig/all *.
  This would list all the details on the WLan/LAN cards installed in the laptop.
  The physical address means MAC address ;)

  This should help!

• Satellite Pro 6100 Modem does not - No Dial Tone

  Hello

  I'm in terrible trouble. I have a big meeting Friday and discovered that the internal modem on my Satellite Pro 6100 does not work. I downloaded the drivers of software Modem since the support site, and the installation seemed to go OK. There are no conflicts listed in the Device Manager, and when I query the modem to in the properties of the modem (from the control panel), it seems question OK too, but...

  HE DIDN'T THERE WAS NO DIAL TONE!

  I don't know that it is connected to my phone OK. Instead of a tone, I hear a loud hum, with a series of clicks. I can't hear being composed either DTMF tones, even when I disable "wait for dial tone. This behavior is the same if the modem is connected to the phone line.

  I have a big rally Friday and will need this modem to work... any help would be much appreciated...

  Thank you

  Matt.

  Hello
  that doesn't sound so good!

  The measure where I read that your ad you´ve checked your system almost all.

  Right on the thing, have you installed a firewall or other programs to check system that denied access to the modem?

  It is also ok, you should let check your laptop on a faulty Modem.

  Good bye

• Satellite Pro 6100 has no Wlan

  Installed xp on a Satellite Pro 6100 and it has no wireless network adapter in the Device Manager to all, and it does not appear in "Found new hardware" or whatever it is.
  I downloaded the drivers, but I can't put anywhere.

  Remember that the wireless card is an option on this laptop.
  This means that some Pro 6100 was delivered with the WLan card and some does not support the minPCI wireless network card!

  If the WLan card is not listed in the Manager of devices (or as unknown under network adapters device) then the laptop was not equipped of the WLan card and so you cannot use the WLan.

• Sat Pro 6100: Moving by itself of the mouse

  Hi all
  You have a question about a problem I'm having with my mouse two USB and the joystick on my satellite pro 6100 xp sp2

  The poroblem is that the cursor moves off the screen, either in the top right or bottom left. Tired using laptop without usb mouse same problem, have scanned laptop in case of virus, found nothing. been looking for the web, but only to find that the people who have had this prob is with mouse Sales (Laser or infrared ones)

  I was wondering if it's got time my keyboard replaced in which case this is the problem is, the mouse uses a bit of the keyboard to work.

  Someone at - he encountered this before and could point me in the right direction

  see you soon

  Hello

  Well it s strange. The problem occurs if the joystick is not connected?
  This resembles the function of calibration of joystick or mouse.
  Have you tried to calibrate the joystick?

  Also the same problem occurs if the accupoint mouse trying to calibrate. The mouse cursor moves to 5-10 seconds. Right now you shouldn't t touch the mouse.

  Good bye

• Sat Pro 6100: The orange light blinks

  GDay guys,.

  Thursday, it was the last day of school.
  In the last lesson of the day, I used the laptop to play games (Toshiba Satellite Pro 6100, 1, 6 GHz) when the Bell went. I tried to stop in time, however running in battery mode, she went up to 1 ghz and has been quite slow, closing the game so I immediately turned it off by holding the button for a few seconds.

  I put it in my new computer case belkin which offers a thick foam padding and went home by bus. When I finally got it, I plugged the laptop and tried to boot the system. The screen didn't work for some reason, so I tried the key light several times without success. Reset the computer several times, still nothing. I was wondering if it was the hard drive of the stopping is not correctly earlier this day here but I could always blindly log windows. It me intrigued as to why the screen wasn't on. I presume that a cable was loose so I removed the keyboard and checked the cables on the graphics card. They were fine. Put the keyboard back on and tried to start the laptop.

  The flashing yellow light has shone in its ugly glory. Something was wrong. I left the cell only and got the father, who is an electrical engineer to check on the laptop for all things obvious which could cause this problem. Dad couldn't see anything.

  Before, I read a post on the resettlement of the graphics card can work so I reinstalled the graphics card and tried to boot the system. Still nothing!

  What the hell is happening?

  I read these support forums and find a post on how you can charge the battery, start etc and try it and watnot, but it still fails. When I remove the battery and exit onto the adapter and replace the AC adapter in, a green light that shines above its power light shines. When I put the battery in again, a yellow light shines above the stack, however as soon as I press the power button, everything shuts off and the yellow led shines above the logo of ac power...

  Any ideas as to what may cause this problem and how can I solve this problem?

  -Well done guys!

  Hello

  Littco is right. You must contact the partner in your country. On this way is really not easy to say what can be the problem, but I guess Hat there is a problem with the electronic control gear and you will not be able to repair only. Check it please this page

  http://www.CSD.Toshiba.com/cgi-bin/TAIS/Su/su_gaspLocator.jsp?PF=true

  and there you can find a list of aspic in your country.

  Good bye

• Need a plan of construction or images of Satellite Pro 6100 for BT / WLAN position

  Hello

  I need a 6100 construction plan or some pictures of the location of the device Bluetooth and WLAN.
  This parts are modifiable or not?
  Because I have bad RTC 6100 with WLAN and Bluetooth and another who works without this two devices so I want to build this parts in the workbook, but I don't know where they are or if it is possible to do.

  Thank you

  Here is the plan for the two, BT and Wireless Lan for the Toshiba 6100
  http://Weller.WS/Toshiba/antenna.html

  The BT card slot is accessible from the bottom of the laptop. (just a screw to lose)... you will see the pink BT antenna wire there, too.

  Internal MiniPCI wifi requires that you remove the keyboard first (two screws covered by plastic on the top of the F1... F12 keys) then open a plastic cover that hides the Mini-PCI card (the location is where would be the "F6" key). It requires a force to remove this plastic cover ;)

  Concerning

  chain

  P.S. All additional cards (BT and WiFi) are sensitive parts of static electricity. If you plan to trade on your own, take the necessary precautions. If you are not familiar with this, please consult your nearest Toshiba service.

• Sat Pro L10: built in WLAN issues

  Hello

  I am using the inprocomm WLan on a new satellite Pro L10 running XP Pro with Windows zero configuration disabled.

  I have 2 routers netgear acting as access points, with several other wireless devices work well.

  I found a few problems:
  local network utility does not define the WEP key at startup (and does not work with reliability of boot).
  You cannot run the utility except if connected as an admin user.
  profile settings not retained "broad machine", only by the user.
  the support inprocomm website does not appear to exist (www.inprocomm.com.tw).

  most are small problems, but the lack of reliable startup is a major problem. I had an another toshiba I got before reliable machines, but this feels like the beta test software.

  the drivers are up-to-date (even if it is not updated on the web site of toshiba, and pilots were dated 2004)

  Anyone got directions on how to do it?

  I spent a day of evil and cannot do this work anyway for a non admin user, and must always start manually for work at all.

  Stephen

  Hello.

  I m unaware of this key WLan card because it s are not a product of Toshiba but
  I found a site with Inprocomm WLan drivers. Please check for this possibility.
  http://list.DriverGuide.com/list/company3145/

  Do you have accounts for different users on this device?
  I think that you need the appropriate permissions for all users.

  Good bye

• Satellite Pro M70: Configfree and Wlan with WEP issue.

  I have a Satellite pro M70. With Configfree (v5.90.07), I can connect to the wireless network (with SSID) of my router and go to the internet. But when I put a WEP key in the router, and then I can not connect anymore.
  With Configfree, wireless Lan, I still can't see the network (with the name of the SSID, etc.) and I see that the network is secure. But I can't connect to the network more. This because the laptop adapter (Intel 2200BG) doesn t have the WEP key. My question is: How can I set the WEP key in Configfree? (A different key by different profiles).

  (Try to solve the problem I have downloaded the new Intel and IntelPROSET wireless drivers.) This live program asked the WEP key and makes a link without problem. Now with Configfree, Wireless LAN, I also see a connection (secured with WEP). But the rest of the Configfree program does more (CFMain.exe problem). I read in another topic that this is caused by the Intel program. You must remove this to solve the problem of Configfree. So this n t the solution.)

  My question is: How can I set the WEP key in Configfree? (A different key by different profiles).

  Hello

  Firstly the Toshiba Configfree program is not software for the WLan configuration.
  This program, you can use for the diagnostic procedure and it shows you the connection properties. But it of not possible to set the cipher with the Configfree.
  It seems that the IntelProset utility has a bad influence on the Configfree. The problem is that Toshiba doesn't support any 3rd party applications.

  Furthermore if this card doesn t WLan supports WEP encryption so you can not use it.
  WEP encryption, you can set in the WLan card properties.
  You also use the 3rd party WLan application like IntelProset or Atheros utility to configure the WiFi network but encryption depends on the WLan card not on the utility!

• Satellite Pro U400 starts and overheating problems

  Hello

  6 weeks ago, I bought a Satellite Pro U400. Shortly after that I bought, I noticed that the computer overheating. After 1 hour of use, it becomes very hot in the touchpad area, as well in the base of the computer and on the touchpad itself. It is very annoying because I almost burn my fingers with the touch pad.

  The problems began 10 days ago. I had been using the laptop for an hour when it suddenly turned off without notice. Power outage? I don't know Don t. I looked like a sytem of overheating protection. My previous laptop had the same problem. After a few minutes, I was able to turn it back on.

  Then it happened again a few days ago, but it took me 5 minutes to turn on. Yesterday, it happened again, and after 45 minutes without response, I went to bed. In the morning, I was able to turn it on.

  This also happens when wifi is disabled, it is not only a problem with the wifi card, overheating of the system.

  Am I the only one having this problem? I will try to send it back to Toshiba for a replacement or a refund.

  Is this normal in a really new machine?

  Thank you

  First, the warming of the touchpad is normal for almost every laptop, due to construction. Under this, there are the HARD drive and it produces heat. With my last books, and it was not bad, too.
  But really to get so hot?

  Due to the protection against overheating, it is normal that you cannot turn on your laptop immediately.
  But the wireless card is not the device in question, because it's a very small piece of hardware and produce little heat.

  You said, you had this problem with your notebook previous too. Let me ask you, when you use your notebooks? What your table surface there or is there no matter what on that table cloth?

  What I can tell you right now is, to check your locations of fantilation for all dust or maybe you have objects near it so that hot air can not cool.

  Post edited by: InvaderZim

• Satellite Pro 6100 gel and close

  Hello
  I just bought a second hand 6100 and after about an hour of use it stops, I guess its overheating as about 10 minutes later, I can restart

  I also have the RTC message that seems to be very popular

  Can someone let me know how to check the radiator & Fan and if the cmos recharges its free if I can get the laptop to continue to operate for long enough

  any help would be appreciated

  See you soon

  Hi Andy,.

  Overheating is a common problem with most laptops and can usually be resolved by using an interior hose of the vacuum cleaner on the grids of aspiration air for a few seconds. This effectively pulls the dust and debris out of the heatsink through fans. It also avoids having to disassemble the radiator that is usually attached to the CPU thermal paste.

  Regarding your RTC battery, this will normally rechanrge once the main battery is fully charged. I suggest that you leave the device attached to the power supply for at least 12 hours after the main battery is fully charged. This shopuld be sure the RTC battery is also fully loaded. It is always possible that the RTC battery began to fail in this case, it must be replaced.

  Kind regards

• display MacBook pro on safari and chrome problem

  Hi all

  I have a MBP end 2011 that took her mother changed twice. First of all, it wouldn't start when I installed an additional RAM module (I 2x8Go) and then it starts crashing while working last summer.

  Now, this is something similar: screen (no ice optional screen hi-def) becomes crazy (black screen and then blur and not centered) then the MBP freezes and restarts. I noticed that it always happens while on chrome or safari and if I stop immediately after it starts, the display will return to normal and I can reopen the browser for a few minutes until what it happening again.

  The time it takes to do is incompatible.

  I got an error code of Apple Hardware Test (but only on an extended Test): 4MEM/62/40000000: 0 x 84339018

  I'm under El Capitan 10.11.5 without problems so far. Chrome takes up a lot of memory, but I think it's OK but navigation now seems much more slow processing of even very frequent beach ball time when nothing else is running and the memory and the CPU usage is well within available resources.

  Have not yet done this new info from Apple but I have appointment Thursday based on the problem of the screen and crashes. If there was a MB issue they will replace for free but 1 / I need my computer operation Monday (starts a web programming crash course 2 months!) and the repair could take more time than that and 2 / even if repaired once means that I'm working on a bomb ticking.

  I intend to have a small external hard drive with time machine for the entire cycle (I on my NAS when at the office) - how convenient - but I'm always SOL if it happens during the course. I'm not a programmer at all, so it's a challenge already to deal with a failure of the computer at the same time!

  Any advice would be appreciated!

  Thank you

  Antoine

  The error code you posted shows a RAM problem.  I might try the original RAM and see if it makes a difference.

  The specifications for the new RAM modules: DDR3 SO-DIMM of 204 pin PC-10600 (1333 MHz)?  Macs are very selective with RAM.  Some brands do not work well in Macs.  OWC and Crucial are the best sources for RAM Mac compatible.

  You can also try the following:

  Remove the RAM and clean the contacts.

  Take one module, insert it into a slot and start the MBP.  Place it in another location, and then start the MBP.

  Repeat with the other module of RAM.

  Essentially, you test if a RAM module is defective or if a slot is defective.

  Ciao.

• Satellite Pro P100 - screen and sound problems after upgrade to Windows 7

  Hi all

  I got my Satellite Pro P100 (model number is PSPAEE-00C006EN and the second digit of the serial number is '7') upgraded from Vista to Windows 7, and since then, some bugs seem to have had place - can someone help me on the following:

  -L' screen DIMS increments, irrespective of the fact that I have saved my power settings to stay on FULL (battery or sector)

  -No sound. Once or twice, the sound card worked and settings to say this works correctly (and you can see the movement of the graphic equalizer).
  In terms of PC knowledge, I would be 5/10 (so not a dummy, but certainly not a pro! and we tried a lot of the more obvious things)

  Thank you all

  Hello

  1.) if the screen dim option doesn't properly work, I recommend you to reinstall Toshiba Value added Package. This package controls these functions, the keys FN and others. Visit the Toshiba page for an update!

  2.) did you check if the sound is muted if the equalizer work? In addition you can also try to update the audio driver might it work ;)