Satellite 2540 cds - startup problem

Similar Questions

• Satellite 2540 CDS, boot problem

  Hello
  I have a satellite 2540 CD and when I turn on the hard drive does not start. He made a little sound like it wants to start but then kind of stops. I have the power led, HD light, seeing the battery. The light on the drive is also on. I tried the reset button but nothing changes. The HD is fine and the power is very good. Is there a combination of magic button to turn it on? Help, please

  Hello

  As much as I know there is no magic button, but sometimes, it will be very useful to have a. Am I wrong?

  In my opinion, you should try to enter the BIOS settings. Check if the HARD drive is recognized correctly. Alternatively, you can try to start the device using the departure of dick. Check if you can change to C:\ A:\ and verify if the contents of the HARD disk will be displayed correctly.

  Good bye

• Satellite S1800-814: startup problem, screen is black

  I know there are several comments here to point out how the black screen at startup. I think my problem is similar, but I need a few more details.

  A year ago, a friend of mine gave me his old laptop, a Satellite 1800-814. I use it mainly as a typewriter and check my email. He could never operate on battery only, longer than for a few seconds, but I've always used it with the connected power cable, no problems. Sometimes it wouldn't start, and I had to unplug the power supply for a while to turn on.

  I was visiting someone and wanted to connect to the Internet. They had this USB wireless modem, that I have it plugged into my Toshiba. During installation, the PC froze, and I had to reboot by pressing the button market for some time. He did restart, but at a standstill. I restarted again, sometimes had it works, sometimes not, and ultimately he entered its current state: with the power cord plugged in, it will start, I'll hear the processor fan (or whatever it is) work and the lights of the battery and the power will be green at the bottom of the keyboard.

  The screen, however, is black, there not all sounds and ceilings and the insert key lights do not react to what whether - they are permanently gone.

  What is happening here? I tried to remove the battery, give it some time and then reinsert, but in vain. I also tried to start it upward with the USB connected modem, no luck there either. What I do have an appointment with the Doc of PC, or can I fix it?

  I have really important documents there. Grateful for any help!

  Your description is quite long, but I'm still confused. You mixed several questions in the description of the problem and there is no stated clear what happens when you press the button walk / stop.

  Power is ON?
  Is there a HARD disk activity?
  You see something on the screen?
  What happens if you use the power supply only (without the battery inside)?

  Sorry, but it is not easy to tell what can be the problem. The best thing you can do is to contact someone with enough experience PC. The person who has the laptop on the desk and try to start this laptop can be more specific about possible problems.

  BTW: Please check this http://support.toshiba-tro.de/KB0/TSD57013H000JR01.htm interesting document

• Satellite 2410-303 startup problem,!... urgent

  Hello!..
  I have
  Toshiba Satellite S2410-303 Notebook
  P4 1700/256 / 30 G, 15XT, CDW, LM
  and had Windows XP home.
  I use my cell phone without a network.
  When I push the power on the laptop, it is
  No not from Windows XP. I just see "contact tomorrow with TOSHIBA.
  message from red logo and getting this message;
  ----------------------------------------------------
  Intel Boot Agent Version 4.1.06
  Copyright (C) 1997-2002, Intel Corporation

  Client Mac ADDR: 00 00 39 xx xx 8B GUID: 4069 19 3 xxxx CADxxxxxxxx 4DB01E00
  PXE - E53: no boot file received

  PXE - M0F: Exit Intel Boot Agent
  Insert system disk in drive.
  Press any key when ready...
  -----------------------------------------------------
  After 5 - 6 times and try to open with power button windowsXP starts, but after 5 - 6 times I turn the laptop on and outside. Windows XP started.
  I looked at the bios settings disk HARD/floppy/CD-CD-ROM/LAN player it's just. I use the latest bios updated.
  What is wrong please advise
  What is the problem please help...
  Thank you very much

  [Edited by: admin November 16 04 08:18]

  Hello
  I have a Satellite 2430-101, which has had similar problems.

  Seems to me that your computer laptop sometimes Don t recognize your HARD drive.

  My suggestion is, if you have another HARD disk, change it to look if the problem persists.

  If so, I think that your IDE controller that is responsible for the detection of your HARD drive is damaged.

  Good bye

• Satellite S1800 100: startup problem

  I have a laptop 100 S1800 as a second machine and have recently experienced problems at startup. Food, power & battery LED turns on but nothing happens, no power at all. I have to keep on and off until this finally that she comes to life. Sometimes on stop, he made a series of beeps before stopping.

  Hope that makes sense for someone that I'm stumped.

  See you soon

  Hello

  Perhaps there is only one small problem with the power button, but due the beeps it can also be a major hardware failure. In any case, you should take the machine at the service.

  Good bye

• Satellite 2430 XP startup problem

  Windows XP will not load on my laptop Satellite 2430-402, saying that the C:\Windows\System32\config\system file is missing or damaged and to try to run the option repair.

  I have 2 Toshiba Recovery CD which I managed to launch the program of recovery based on the BACK which has 2 options:

  1 full restore, I want to do
  2. selective restore, I don't want to do, but have no instructions

  I don't seem to have an XP CD, where I could start recovery of Microsoft application.

  Can someone give me the steps to undertake a selective recovery of Toshiba (from Symantec) back-based recovery CD?

  Thank you

  Hello

  In this case, I'm always ruthless. Back up the data and do fresh install. Then only I am 100% sure that everything works correctly. :)

  Anyway, if you want to make new installation with restore CD there are two possibilities:

  -Standard mode (any partition is deleted and new operating system installed)
  -Expert mode (you can choose which partition you want to install the operating system)

  It is very important that there is no repair option. This option you can find on the CD-ROM of Microsoft Windows XP.
  There are few opportunities to try to repair your operating system. You can try to replace the faulty system file. Copy the files from another PC system and replace it. I must also tell you that there is no 100% guarantee that it will be successful.
  You can also try to provide the Microsoft Windows XP CD-ROM (full version). You may have some success with the repair option.
  Next option is to use the Windows Recovery Console. I assume that you have access to a second computer. Click here for instructions that can help you.
  http://support.Microsoft.com/default.aspx?scid=kb;en-us;314058
  This article describes the features and limitations of the Windows Recovery Console. If your Microsoft Windows XP-based computer does not start correctly or if it does not start, you can use the Windows Recovery Console to help you recover your system software.

  Here a few days ago was interesting posting on this topic. You can find it on:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=1823

  Good luck!

• Lost my Satellite 4090 CDS recovery CD

  Hi all,

  I have a purchased a former used Satellite 4090 CDS, but unfortunately without a recovery CD and the OS.

  Does anyone know which OS is on recovery and where I could get a new one?

  Antoni Bye

  Hi Antoni,

  It's bad, but here's a FAQ to solve your problem.

  FAQ is a list of laptops with their OS Recovery CD supplied.
  Reach

  http://UK.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/faq_selection.jsp?

  and choose the FAQ with the following title:
  "What operating system and recovery media came with my Toshiba Satellite Notebook PC?"

  If you want to order a new recovery CD, you must go to a Service partner and write a solemn declaration
  with some general information about your machine. Then, you can order a!

  On the following site is a list of all Service partners
  under Support & downloads - Find Service partner

  http://EU.computers.Toshiba-Europe.com

  I hope this will help you!

  Rudi

• Reverse satellite 4070 CDS screen

  Hello

  My Satellite 4070 CDS seems to have a reverse screen. Is there a key combination or another solution to get back to normal?

  Thank you

  Enno.

  Hello Enno

  What did you mean by reverse screen?
  Did you use a large monitor? Please explain precisely your display problem.

  Best regards

• iMac troubleshooting ADVANCED startup problem

  Hello. My iMac does not complete the boot process. It chime, then display the Apple logo.

  The progress bar will get about halfway, then disappears from the apple logo. Gray rest screen for about 2 minutes, then the computer shuts off and the process repeats. NOTE: the computer does NOT respond to the "safe" mode (shift key) or (command-R) disk utility commands. What else can I try?

  Start - computer restarts by itself-Yosemite

  Resolve startup problems-

  Resolve startup problems - (2)

  Resolve startup problems - (3)

• Cannot install ethernet on Satellite 1710 CDS

  Hi, I have Satellite 1710 CDS.
  This laptop has RJ45 wording "Ethernet" connector on the rear side.

  In my book there is not written anything on the inbuild ethernet card. Photos of manual shows back of laptop, it has drawn no ethernet connector, but my laptop has had! Is this possible?

  Why toshiba is not talking about ethernet in the manual for CD of Satellite 1710 and my 1710 has? I don't understand.
  Windows ME cannot recognize this net adapter. I don't know what drivers should I look for. Please help me or give me advice. Thank you.

  Hello

  Sorry, I have you dissappoint! Satellite 1710CDS has NOT built in LAN!

  The cover has only a black RJ45 model at the backsite without function!

  :-(

  Rudi

• Re: Satellite P200 (PSPB6E) - keyboard problem

  Hello

  I have a keyboard with Satellite P200, series PSPB6E problem.

  Keyboard seems to generate Press Page Down constantly, although nothing has been paid to this subject.
  It is even difficult to turn on laptop, because it produced consecutive beeps and prevents the computer from starting.

  Sometimes some keyboard characters do not work, and in the second time it works. Sometimes same PgDown works as expected.
  Œuvres for additional keyboard, but it also receives PgDown keyboard of the laptop.

  Now, I can't insert any sentence in this post, because PgDown will move the cursor down.
  Laptop is under warranty. Should I enable it?

  I note that no. LIQUID is poured on the keyboard.

  On the keyboard of the computer laptop not work keys A, B, N, LEFT SHIFT, INPUT, same brief moments where PgDown keys not dumping. Sometimes even these key works!

  Best regards
  Vladimir Stefanovic

  Great news, buddy! :)

  I also have good experience with my ASP. They fixed the laptop as soon as possible and the repair took only a few days. It's also free.

  So still I m happy with the service!

• message from startup problem: imac photos: er zich een has doing voorgedaan bij het recovering bevoegdheden van (an error occurred in restoring the powers)

  message from startup problem: imac photos: er zich een has doing voorgedaan bij het recovering bevoegdheden van (an error occurred in restoring the powers)

  Do you mean, there is an error message about problems with access rights? (toegangsrechten?)

  Where your photo library is stored? In your pictures folder, or on an external drive?

  You share the photo library with another user?

• New problem z50 - 75 wireless? Startup problem

  Hello

  I had an another hp laptop which had a problems but the know-how could not fix it so they give money and I brought another Hp 4 days but then she had to be exchanged because of defective. Currys and PCWORLD even gave, but the problem kept pass. So I just paid the HP one and brought 3 days LENOVO Z50-75 it y a. the first Hp laptop, I had, had dns clients warnings in Event Viewer when you use wireless. Same thing on the new computer hp laptop. This problem still occurs in the LENOVO one too. These events started in Windows 10 for all laptops hp and lenovo. My computer laptop lenovo came with windows 10 in any case. So either it's a bug that should be fixed by a new update for the network adapter needs to be released. Computer laptop lenovo has Qualcomm Atheros the old hp laptop realtek the new computer hp laptop that was defective was and intel double wireless broadband and the same edition, DNS CLIENT EVENTS 1014 WARNINGS are still happening. This is definetley not my ISP fault because I replaced the router, more they found nothing on a week 2 diagnostics test on my internet. SO I just want to say lenovo that if there is a way you can fix this. Another thing is that after installation WIN10 threshold 2 on Lenovo Z50-75 when starting of the laptop it shows the logo screen once then black lenovo and then black screen again, then it boots. I have also all the latest updates. So if there is a way guys can fix that also. I'll post this in the microsoft forums too if they can help. Thank you

  Hi I managed to solve this problem by disabling the DNS CLIENT service, but always the startup problem also happens when I stop or restart the cirlce logo going arouns the shows as usual then flashes then closed restartsor and the same thing happens in the Welcome screen it flashes (black screen for a second), and goes after UPDATE of TH2

• HP Pavilion 23: startup problems

  Because we bought our computer in October 2014, we had many problems with the start, problems of drivers, startup problems, graphic card problems and more. It was supposed to be fixed once by the bu retailer still, there are questions. The biggest problem is starting:-it freezes, error messages that say lag not found drivers or disk not detected though when checked is. Also, we have done numerous resets hard which are just a quick temporary solution and back problems. We pay every month for a service contract with the retailer, but they mostly just try to run the store for our computer repair you... NOT HAPPY because for the third day, we bought there have been problems and we haven't bought a computer to sit in a workshop constantly, not at the price we paid coupled with the monthly fee for whatr amounts to nothing. Is there something we can do to solve this problem without driving miles and being without a computer that actually, we bought to USE?

  Hello

  Without compromising your contract, I suggest

  SYSINTERNALS which is a suite of tiny applications bit that may help.

  https://TechNet.Microsoft.com/en-us/Sysinternals/default

  Now only 3 or 4 are likely to be beneficial, and some does not at all because they are for servers etc.

  Thus a special interest may be...

  AutoRuns

  LoadOrder

  RamMap (maybe)

  Contig (maybe)

  PageDfrg

  ROOTKITREVEALER

  DiskView (maybe)

  PsInfo (not really)

  psping (not really)

  After trying a few please ask if there is something to be interpreted.

  I suggest you turn off auto update if you can.

• URGENT HELP PLEASE! Windows did an automatic update finished & gave me the Option "restart now or later. I chose Now.A screen from Windows is going down, a startup problem occurred immediately after the installation of updates, this has happened about 9 h

  Windows has finished just do the automatic updates on my Sony Vaio... He said that he should be released on... When it restarted it goes to the ' start windows normally, safe mode, safe mode w/network, safe w/command prompt mode and the last known good configuration "screen... I tried "start windows normally", and last known good configuration, and no matter what I did, it looks like its about to begin, with the 'windows' logo & he says it's the boot process, but then instantly a screen flashes, but too fast for me to read what he says, so I immediately finished fashion splash screen choose again. Whenever I try to get my PC to boot it goes through this again. Exactly... I tried restarting, shutdown PC up to 30 min. waiting & more & again it does the same thing & will NOT start! HELP PLEASE!
  I do not have my current work & News & saved downloads & need help & I timed commitments to people... ASAP PLEASE!
  Thanking you in advance...

  Windows XP logon screen does not appear and the computer continuously restarts
  http://support.Microsoft.com/kb/310396

  Resources to solve startup problems in Windows XP
  http://support.Microsoft.com/kb/308041 TaurArian [MVP] 2005-2010 - Update Services