Satellite 5200: lines on the screen - driver does not properly

Similar Questions

• DVD/CD driver does not properly, the discs are not read.

  I tried different discs and none are read which is very annoying, because I can not install my new printer! When I checked the driver, the following message is displayed:

  Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19)

  Click on 'Search for solutions' to send data about this device to Microsoft and to see if there is a solution available.

  I click for solutions and he's looking for a few seconds and then nothing happens. I tried it 3 days ago and still today, but it still does not work, can I do?

  Thanks in advance for any help

  Hello

  19 code means there is a driver conflict such as two devices attempt to use the same resources.

  Please make all below even if you have done some before as it is often the set of operations which solves
  the question.

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack. Even if the reader does not appear to continue below.

  Normally the above will solve this problem otherwise working your way down through them, even if you did
  them before.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  Hope these helps.
  Rob - bicycle - Mark Twain said it is good.

• Graphic drive does not properly.

  Graphics driver does not properly.  Screen will Dim and must restart to resume use.  Occurring more frequently now.  Y at - it a fix for this problem?

  Problem does not occur in safe mode.  Failure seems to occur on any key or the video style.

  Any material support is the manufacturer of the hardware regardless of the operating system that you choose to use.  As it is unlikely that you have a Microsoft video/graphics card - one you have and have you downloaded and installed the latest drivers/software they provide for your particular device?

• CD/dvd drive does not properly

  drive will read DVDs but not cd. Once in a while, it will read a cd, but it shows the cd as empty (no space) I know that the cd is full. any help would be appreciated

  Hello

  You have disk problem as the CD/DVD is actually 4 discs in 1 case (burn CD & DVD and CD and DVD read).
  Therefore, it is not unusual for 1 or 2 rooms with not so work that others do it properly.

  Please make all below even if you have done some before as it is often the set of operations which solves
  the question.

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack. Even if the reader does not appear to continue below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
  slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  -----------------------------------------------------

  Several good info here:
  http://Club.myce.com/

  Notes on the troubleshooting and repair of readers of compact disks and CD-ROM Drives
  http://www.repairfaq.org/repair/F_cdfaq7.html#CDFAQ_014

  Hope these helps.
  Rob - bicycle - Mark Twain said it is good.

• Satellite P200 accidents + message: graphic card driver does not work properly

  Hello

  hope that this issue has not been covered before, but I've owned a Satellite P200 for 3 years now, and this week, it crashes all the time.

  When it started going down he gave me a few messages in the sense of "your graphics card/driver does not work properly and windows will be arrested to avoid damage.

  It has progressed to the point where now when I turn it on, I have vertical lines running down the screen and the screen flashes on and outside. Within 20 seconds, it restores the BSOD - 'there was a problem and windows will be arrested. Error Page_Fault_In_Non_Paged_Area"then stops.

  I ran a system restore but the problem remains.

  I have a feeling that my graphics card is toast. Is this good? Are there any other options to try? Thanks in advance for any answers.

  Matt

  Hello

  Sounds like the GPU problem.
  But try the graphics card driver update.
  Use the most recent driver for your graphics card.

  In addition, clean the fans of portable computers.
  Dust and debris could prevent the cooling fans to turn with the best speed and this could lead to a higher temperature which would lead to overheating.
  Use a jet of compressed air. I also use it and it helps to get rid of dust and debris.

  If this is not enough, then a problem of graphics chip would be possible.

• Satellite A305-S6858 win XP video driver does not

  I recently bought a Satellite A305-S6858 in the States and I went down the Edition Vista Home premium preinstalled
  for Win XP 32 sp 3. I had several problems to lift the computer up and running. After reading several posts
  on various forums, I managed to install the OS, but I still cannot use the Intel video driver.
  After the installation of those available on the toshiba site I still have in the Device Manager under the node for the video card
  2 entries for 965 Chipset Mobile with an exclamation point.
  I recently discovered that not having is not the video driver installed the operating system does not allow Stanby and Hibernate power options.
  If someone has stumbled in the same issue?
  Thank you

  You must install the basic drivers first.

  Try to install the driver for the Chipset Intel first, then the display driver.

• Satellite Pro A120: DVD/CD-RW drive does not work

  Hello: the dvd/CD-RW drive does not work. apparently it has been disabled somehow! Any ideas on how I can turn it back on?

  Have you tried the Device Manager and it says it works normally!

  Any ideas please?

  Thanks :)

  > apparently it has been disabled somehow
  I put t think that the disc has been disabled!

  How someone or something should turn off the drive? You have disabled the drive? I don't think so!

  You said that the drive appears in Device Manager. So I guess that the drive is enabled and is recognized by the OS.
  You are getting error messages or what's wrong?

  Perhaps the reader can read or burn CDs or DVDs.
  This happens if the lens of the drive cannot calibrate properly and can not handle the inserted media.

  Maybe the replacement drive is required!

• Re: Satellite L10 - 193 - Win XP WLan driver does not feature

  Driver downloaded from the product page does not feature.

  Device Manager: network controller (yellow)
  PCI\VEN_8086 & DEV_4220 & SUBSYS_27418086 & REV_05\4 & 93A 72 167 & 0 & 20F0

  System: XP Home, just installed

  All other drivers from the Web from Toshiba site for this model are OK.

  How to solve this problem?

  Have you tried to install THIS driver?

• Aspire 5740g and the dvd drive does not appear in 'my computer '.

  I had to have a new installed hard drive I got an error message saying old default disk.

  I also had a clean install of windows 7 that I was uncertain if my discs that I created would be ok.

  So I have not all the gifts that have been installed on the laptop like new. Now, I find that the dvd drive is not displayed in my computer and nothing happens when I insert the disc.

  This has happened a couple of days and I did a restore of the system to a previous restore point.  Does anyone know how to solve this problem.

  I also do not have the secure egis - any ideas how to get this back

  Then... your DVD is probably defective.

  did you check in the BIOS if it is listed on bootable devices?

  Press F2 at startup, if it is not listed, it is defective.

• I can't play discs or load programs on the disk, the disk drive does not work

  My disc drive won't play music discs, or program.

  Hi shaymoss,

  1 when was the last time it was working fine?

  2. did you of recent changes on the computer?

  3. what happens when you insert the disc in the drive?

  4. What is the number of the brand and model of the player?

  See the Microsoft article below and run them the fixit tool available, check if it works.

  Try the manual steps, mentioned in the article, if the fixit tool does not fix the problem.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/kb/982116

  Check the status of the disk on the computer by using the Device Manager and after return with details.

  How to solve the problems of hardware with Device Manager

  http://www.Microsoft.com/windowsxp/using/Setup/learnmore/devicemgr.mspx

• Need to reinstall my Windows 8, but the optical drive does not

  Separated from this thread.

  Support recovery of Windows 8 for product windows operating system recovery disc Windows 8 pro OEM Activation required 3.0 here in my hands, I have... I can't install them well... My dvd drive does not work with Windows 10.windows 10 sucks... I can't figure out how to take everything here and remove all ten and just replace my 8...

  Since you probably need creation for Windows 8.1 installation media on flash stick to do anyway the own 8.1 Windows Installer , you might do as well on the contrary much better Clean install Windows 10 since the installation in the link worked for everyone who tried without a single complaint, overcomes all and every other issue had with 10 Windows and gives the best installation of any Windows OS We can possibly have.

• RAID-1 failed, the second drive does not start in RAID

  I bought a Dell 531 running Vista with RAID1 set up on two 300 GB drives.

  And that works very well... but then the first disc got a bad place.

  Ideally, I could unplug this drive and run the other player;

  However, the second disc has a RAID boot sector!

  [he has a normal boot sector, so if I plug it into the unused (non-RAID) SATA-3 slot, it will start]

  Should be no problem, just start the recovery DVDs and let Vista install a good start...

  But NO!  The DVD version does not see the drive.  (I tried to load the sataraid drivers, no joy)

  Note: if I have the drive failed in the RAID and the second drive in SATA-3, it starts to SATA-3.

  If I put the two drives on the RAID, it starts on the failed disk.

  Now I have a replacement for the defective drive.

  How to make 'good' initialization as a RAID drive and rebuild the new drive?

  How can I get a boot sector capable of Vista/Raid on the disc?

  
  

• I have a Toshiba satellite L455D laptop and the touch pad does not work

  If I plug my usb wireless mouse that works, but when I unplug it the touch pad does not work

  Have you checked to see if your laptop model has a physical button around the mouse pad that allows & turns off?  If it does not, many cell phones often have a software switch that can toggle the on & off power mouse pad.  It is usually triggered by a combination of function keys (key Fn + one of the F1 to F12 keys).

  Take a close look at the row of the top of your keyboard and see if you can find a key that has a small symbol that looks like a mouse pad.  If you find one, try pressing it in combination with your Fn key to see if your mouse pad features returns.

• Captivate 6 Audio screen slide does not properly

  Trying to re-record audio for a slide today this screen open - I could save, but not save, because the record button does not appear.  I was able to record new audio files on the same Friday project.  I tried to delete and new audio recodring and the same screen came.  I tried another project - same thing happened.  I rebooted twice.  Any ideas?

  

  Thank you!

  Rachel

  Hello

  If you check the address bar of your screenshot, you'll see that you are in the folder "C:\Documents and Settings\ [user name] \Application Data\Adobe".

  Could be a possiblity that "Local Settings" folder is hidden, click on tools-> Folder Options, view tab, you have the option of "hid display files and folders.

  

  You can see the local settings folder when you click OK, then you can go to C:\Documents and Settings\ [user_name] \Local Adobe application and rename the folder "Captivate 6.0.

  Hope this helps!

  Thank you

  Vikram

• Satellite A660 - lines on the screen

  Hi all

  Recently, I noticed that when I turn on my laptop there is a band of what looks like a line of black spots. In addition, I've got lines everywhere which makes it almost impossible to see!

  Now there is no way in hell I dropped it nor have I nothing left on the laptop at all, and when I checked, it was not visible cracks on the screen. With respect to maintenance, I use it a hell of a lot in college but I usually carry it in a laptop bag which has a compartment for him, I turn it on whenever I use it not and I certainly go a drop or leave anything on what could cause it to crack.

  That's happened through hell? Could he cracked internally? And if so, how the basis that occur with or without any force? Unless it might have been a trauma that I didn't know, but saw that it happened about 45 minutes after the last, I turned off and turned on AND that it is in the same place I left it that was on my desktop, I would say that's a far-fetched possibility.

  I bought this 29 September last year so I'm still covered by the warranty. I checked online that I have an "international limited warranty. -What is the standard warranty? I also checked if the screen is covered by the warranty and it says in him "NOT COVERED" who:

  "Damage caused by accident, intentional or accidental misuse, abuse, neglect or improper maintenance, use under abnormal
  conditions, including fracture or damage to the LCD (screen), treatment of cases, cables, adapters, keyboard keys, lids, caps
  and latches. »

  Because she is probably 'accident', this means that what is not covered? Here's the bollocks. There must be a way that this could be covered by the warranty? I'm not in any kind of position to spend another big buck to get this repaired thing...

  I bought this from Harvey Norman, Australia, which is a well known retailer for these kinds of products.

  Any help is very useful and I look forward to your responses.

  Kind regards

  Charles.

  Toshiba Satellite A660.

  Hello

  Are you sure that this problem is related to the internal screen? Theoretically, it could be the graphics card itself and you can check this by connecting an external monitor. If you can see the same lines on it it s graphic card itself, otherwise the screen inside.

  But I think that in both cases, you need professional help of an authorized service provider. Guys can check your laptop, the new order parts and replace them for you. Also, they can you give an exact answer if this is under warranty or not. Here in the forum we can only speculate on that and he s only forum user.

  So get in touch with an ASP in your country. I'm sure that the problem could be solved as soon as possible with the guys. :)