Satellite A210: Fact of recovery - lack of data on the E drive

Similar Questions

• Re: Need Satellite A210-10y - 3D CAD program doesn't work - new display driver

  Hello

  First of al I have a toshiba Satellite A210-10y, but I have a question for the display driver.
  I have a problem with a program of 3D CAD and a suggestion to solve the problem, is to update the display driver.

  But I can ' find a new driver on the driver support. It seems that Toshiba leave support after 3 months after the introduction.
  Because that's when the most recent driver is out. Is this true or do I go to the wrong place.

  Greetz Tom

  Hello

  The laptop seems to support the Mobility Radeon® X 2400 graphics chip.
  Have you tried the driver released by ATI?

  Toshiba usually provides own pilots on the European driver Toshiba page. But if this version is too old for you, then you should check the driver from makers of graphics chips. Of course there is no guarantee if such driver would be fine, so you will need to test this you know good luck

• A satellite will not start - how to back up data from the HARD drive?

  Hello
  My laptop won't turn. How can I take backup of internal hard drive?

  Please read my writing as soon as POSSIBLE

  If you n t have access to your saved data remove the laptop HARD drive, connect it to the other PC as external device and you should have access to all stored data if the HARD drive is not defective.

  What you need is USB 2.0 IDE 2.5 HD enclosure disk hard drive / external case/Box.

• Qosmio G35-650 - do I lose my data on the HARD drive?

  Ok. I tried everything to repair an installation of XP on my Qosmio G35-650.
  The recovery disk was a joke and would not work... I decided to skip all the DMI troublemakers, I read and clean install a copy of XP.

  Put drivers Raid on a diskette and proceeded with the installation. The installer would not install on the boot partition and gave me an error "page_fault. I went into the bios and changed disk to JBOD RAID 0, disk 1 has already been set to JBOD.
  Entered again the program installation and the place where you select the partition to install only a single partition has been demonstrated.

  It wasn't a good thing I backed up all my data from drive C: (disk 0) to drive F: (disc 1).
  I went to the BIOS and reset the drive on Raid 0 and started the installation again.
  Two partitions have been showing this time but 1 disk did not show a drive F: indicator.

  The question. Have I lost all my data on the second drive of 100 GB in the system?
  My F: drive is recoverable?

  Help!

  If you change the RAID settings, it will wipe the data. Generally, all systems RAID wipe data when they are created.

  But you can have a chance to recover most of the data. There are data programs/recovery utilities that analyzes the HARD disk for the file fragments and attempt to recover your files (at least the files that have not yet been overwritten). Google search for "recovery data drive hard format»

  Why don't you use the recovery disk? If the instrument is incorrect, you can simply download a DMI tool to update the name of the product "Qosmio G35" or "Qosmio G30".
  The tool can be found on the site of Toshiba America.

• Could not initialize and I need to recover the data on the hard drive.

  Original title: computer MOM will not start and I need to recover the data on the hard drive.

  It's an old computer and I do not know what version of Windows it was running.  I guess I need a bootdisk of exploitation, but where can I download that?  Or would it be easier to pull and make a secondary drive in my computer that I just replaced?  It works under Windows XP.

  Hello

  If the old system does not start could be the hard drive. Put the hard drive in another computer as a 2nd drive and then access the files. If you use a computer XP, Vista or Windows 7, you should be able to access the files, unless the drive has failed.

  You can save your files by putting the drive in another computer as a 2nd drive (better) or a USB external drive case and then save up to removable media such as CD, DVD or other USB drives. Of course a real store of the computer or the manufacturer of your system can help to recover the files.

  Or you can use a boot Ubuntu CD to back up data. (This will not work if the hard disk is defective or other issues preventing the system from booting from the CD/DVD drive.)

  Use Ubuntu Live CD to backup files from your Windows computer dead
  http://www.howtogeek.com/HOWTO/Windows-Vista/use-Ubuntu-Live-CD-to-backup-files-from-your-dead-Windows-computer

  I hope this helps.
  --------------------------------------------------------------------------------------------
  Rob Brown - Microsoft MVP<- profile="" -="" windows="" and="" devices="" for="" it :="" bicycle="" -="" mark="" twain="" said="" it="">

• all my data is all save on the local disk c, how to share the data with the other drive, local drive d.

  all my data records on the local disk c, how to share the data with the other drive, local drive d.

  Hi Jasonbichard,

  1. what type of drive is D? Is - this another partition on the same disk?

  2 Windows operating system you are using?

  You can change the location of the disk to save the data in the d: instead of C: and check if it helps.

  a. navigate to the location (username) C:\Users\.
  b. right click on the folder that you want to change the location, and then select Properties.
  c. click on the location tab and change the location to D: drive.

  d. click on apply and Ok.

• Access the data on the hard drive

  My hard drive on my laptop failed.  I replaced and reinstalled windows vista, but I could not access any data on the old hard drive.  I was able to install it as a backup of my desktop computer hard drive and I can see the directory structure, however, whenever I try to access the data in My Documents, I get an error G:\users\moe\documents\my is music is not accessible access is denied.  Any ideas how I can access this information, assuming that it is not a physical problem with the hard drive.  I have the password of windows I used to access the computer, but I don't know how to use it since this drive is not the one I am running windows from.  The computer that I use to access the data on the hard drive is on windows XP, if that makes a difference.

  The computer tries to access the old hard drive and the old hard drive are XP.  It is a forum for Vista.  All the procedures I have on this issue are only for Vista.  You should repost your question in the right place.

  Please repost your question in the Forums XP: http://social.answers.microsoft.com/Forums/en-US/category/windowsxp where XP experts will be happy to help you to gain access.  I don't know it's just a simple issue of permissions and/or property which can be easily solved with the correct procedures.

  I hope this helps.  If you later need help transfer of data to the Vista machine, then come back here and we will help you.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Satellite A210 - error during recovery

  Hi all

  I received a Satellite A210 (opportunity, about two years old) by a friend. The laptop does not work at the moment. When the laptop is turned on, it displays a message "Missing Operating System". I tried using the recovery disk supplied with the machine, but it doesn't help. I get the same message "error restoring image."
  ERROR = ImageX would not apply VISTA F = \05853XSP.swm Index 2 of ODD to C =------! Press a key to continue, and it is as he goes. Currently a une machine machine second hand, that I don't know what works and what does not.

  Any ideas on where to go from here would be much appreciated.

  Hey Buddy,

  I never had an error message during the installation of recovery so I m not sure what the reason for this problem.

  Have you checked the BIOS? Is the drive recognized properly it?

  What happens if you try to install Windows from a Microsoft installation disc?

• Info satellite A210 171 what do I need before using the recovery disk?

  Hello

  I have 1 recovery disk that came with my equium, have not used before.
  It says on the back of the envelope of recovery disk 'insert the first diskette.

  I guess there should be a second?

  Also this info I need to provide during the installation process? as serial number?
  All I have a black and white sticker that is on the side of the box, it came in, but it was so long ago.

  I'm having a lot of problems with windows install does not and many others.
  Windows updates do not work either and I tried to correct those, but a clean reinstall of the operating system has been recommended.
  Now, at this point nothing will install because windows setup will not work.
  So I think I wil lhave to try a clean install, but I do know that the cd player works.

  I got a great run on this laptop, little slow today for my needs, but all very good product, purchased in 2007.
  With a clean OS and 4 GB of ram that could last for years, cannot afford a new right now.
  I really tried to avoid using a disc of recovery in the past, as I have never had problems until now.

  Thank you

  Post edited by: sounds

  > I have 1 recovery disk that came with my equium, have not used before.
  > On the back of the envelope of recovery disk, it says 'insert the first diskette.
  > I guess there should be a second?

  I m wondering why you get this disc with your laptop, why? Because I do not have the recovery disk, but I had to create one using the Toshiba recovery disc creator software
  But my laptop is more recent that your A210 might be the reason why you have this drive

  I have created a recovery disk and I needed two-disc DVD, I think it depends on the size of the image file

  > Also what information I need to provide during the installation process? as serial number?
  This is not necessary because your system has already been activated.

  But I recommend you backup your personal data, because the recovery disk would format the whole HARD drive and you will lose the files.

  PS: you should read other threads in product recovery forum!

• Satellite L300-110 - how to recover without losing any data on the HARD drive?

  Hi all
  I have a Toshiba Satellite L300-110

  The question is how can I recover my laptop with the recovery DVD without losing all the data located in the hard drive?

  I confirm the information published by Luke.
  The HARD drive and all other partitions should be formatted using the recovery disk.
  Why? The recovery disc sets the laptop to factory settings and to this end, the HARD drive must be formatted first.

  That is why it s is strongly recommended to back up the data if you want to use the recovery disk.

  See you soon

• Satellite A210 - 127 (PSAELE) cut off and BSOD after the fresh install of Win 7

  Hello Toshiba Support Forums.

  I installed Windows 7 Ultimate x32bit 2 weeks ago and I have problems around him.
  The only driver I have intalled was ATI video card driver and touchpad driver to make it work.

  The problem is sometimes the laptop shutsdown itself and after I turn it back on it says blue screen and some other information you need, but I closed it.

  Also im gamer and sometimes when I play the game it shutsdown again. When I use Google Chrome or Firefox, the browser hangs and makes the pc of the room with her for at least 10 min. it is really bad and I also want to set.

  Also, I want to ask about memory card reader because I insert a card in the reader, but it does not work I think I need a driver for it but is not in the drivers Toshiba Web page.

  Thank you very much!
  If you need any other information that I will deliver to you order for ifx these annoying problems!

  > The only driver I have intalled was ATI video card driver and touchpad driver to make it work.

  Where did you find this ATi driver?
  It could be possible that the installation of this driver ATi the BSOD.

  My girlfriend has the same laptop Satellite A210 with an ATI Mobility Radeon HD 2400 graphics card. The driver version is 8.632.1.2000 and the laptop is preinstalled with Win 7

  It works perfectly without any BSOD.

  By the way: the cardreder works too... you could take a Vista driver or the driver put the A300 series too

• Satellite A210 PSAFGC - Bios Update to get rid of the white screen problem

  I also have the white screen problem and I would like to update my bios to version 1.30, it came with.
  The problem I have is that I have a number of room A210 model PSAFGC.
  Support bulletin 98082422 for the update of the Bios does not have my room exactly number and I can not find something for my model.
  The 2 updates are at 1.70 and 1.90. I read the text of these two, and they seem quite different.
  Don't know what to do. Here is the info of the bulletin.

  Resolution:

  Update the BIOS of the computer to resolve this problem, by clicking on the link in the following list for your computer model.

  -Satellite A210 / A215, Ref. PSAFGU: BIOS version 1.70
  -Satellite A210 / A215, Ref. PSAEGU and PSAELU: BIOS version 1.90
  -Satellite Pro A210 / A215, Ref. PSAFHU: BIOS version 1.70
  -Satellite P200D / P205D, Ref. PSPBLU and PSPBQU: BIOS version 1.40

  REF. of the computer it is printed on a label on the underside of the case.

  Any help?

  Hello

  The Satellite * A210 PSAFGC * series seems to be a Toshiba * Canadian * series and I would recommend checking the Canadian driver Toshiba page if you want to download the compatible BIOS for your laptop.

  Here is the link to the page:
  http://support.Toshiba.ca/support/download/ln_bymodel.asp

  Best regards

• Satellite P200-1EE Possible to recover data on the HARD drive by placing it in an envelope?

  P200-1EE does not start after 2 weeks off is the case during a fan installation. Is it possible to remove the hard drive, put it in an enclosure and retrieve the data it contains on another PC? Or can anyone recommend how to recover data from the comfort of my own home?

  Thanks for your help

  I would say that your installation of fan caused this problem in the first place. I would check your installation for loose connectors, cards not seated properly, no fan or heatsinks screws tight etc..

  Everything you did everything by installing the new fan plugged the laptop. The hard disk, in my opinion, is perfectly fine. There is nothing wrong with it.

  Put the suspect hard drive in an enclosed and try to access the data on another PC. You will encounter problems with administrator access to certain folders so you will need to find a way to crack in these areas.

  If you had problems in the first place you probably should have this return to the place of purchase for them to watch.

  I hope that for your sake you have not turned into a frisbee.

  Good luck.

• Need to retrieve the BONES but do not have the habit of losing data on the HARD drive

  Dear all!

  For long time now, I tried to disable a Trojan horse or a worm, on my Windows XP Home (Home!) i.e. get rid of the cftmon_.exe, when I decided to follow the instructions from Symantec and pieces manually deleted from the register, I guess she was part USERINIT (turn off the system before restore and put on after the deletion).

  It can be as well as I did not right, something after the fact that I have would be to end the session at the time the logon process has started. This is relatively known issue here, with different options.

  -J' need to keep the data on two HARD drives.
  -I have no other partitions.
  -I don't know what I've got on one of them, which I could use to free space Recovery Expert mode.

  a. the fact that I want to take the option with Toshiba, which is Expert mode (http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=2513&tstart=125) as a last recovery, DVDs on

  b. I have trouble with the installation of the Recovery Console (with Windows XP (Professional!) original CD, 'R' for 'fix), but I would get the message "Setup has not found hard disk units installed in your computer"...
  I understand that I would need to install the driver RAID (http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=20093&messageID=73758) but I'm afraid that this may delete the data on the disc.

  My questions are the following:

  1 install the RAID driver (downloaded from the Toshiba off site web http://support.toshiba-tro.de/tools/updates/raid-drv/raid-drv-qog20-xp-1380.zip and installed on the floppy drive I guess) so we hope to install the Recovery Console, and do the rest of the work, make data disappear my 2 (remove) HARD drives?

  2. If I use Toshiba Recovery DVD, Expert mode that is finally what is the size of partition should be recorded for the mirror on the half vacuum 1.HDD?, should I partition 2 HDD, after it backup and count data will be lost? Choose any setings special during the process, apart from those mentioned in the link above? What should I do after wards? The registry damaged when you logged in and how can I build? I will be able to use personal and archive data from Microsoft Outlook?

  3. is there a alternative with UBCD4Win and UBCD? What is the best? What is the procedure of after the start of the CD after reboot? How to copy/repair the userinit files?

  I'm sorry for the load of information, but I am pretty stuck. All the necessary data for my normal life are buried here!

  A big thank you JohnnyS, tw, Quad, Eldorado and many others!

  See you soon!

  Hi friend

  I would like to respond on comments like yours, it s a good exercise for my work and my s really cool to have a few topics which will help all the people here.

  JohnnyS is a friend of mine who works with me at our office and we talked a bit about your problem.
  If his opinion is to use the UBCD4Win and work with this option.

  The advice from him were:

  Take a USB - HDD enclosure and put a disk in it and start with UBCD4Win. Copy any important data in a folder on the external HARD drive, then remove the uneeded data on this subject. Only important data!
  Make a backup of your data on the external hard drive for two HDD´s I hope that you have enough free space.

  Format the drive in your machine and get it back. Install the system as usual on your first HARD drive.
  Then put the data anywhere.

  So I don't know if I have it just ask, a little more explanation would be useful. I think that this is a long thread. ;)

  Welcome them

• Satellite 1905-s303, WinXP: giant screen, need to update the display driver?

  Hey guys, thanks for your help in advance!

  I am a Satellite 1905-S303 and Windows XP

  Here's what s past with my computer:

  When I turn it on there a little longer than normal to start. And I hear a sound of tck - tck on the back of my computer that I have don t usually hear.

  When it does not start: everything on the screen is HUGE, and I get a window saying: ATI Advanced Desktop Utilities could not initialize, because no ATI driver is installed OR ATI driver does not work properly

  Again, everything on my screen is huge (with the exception of the desktop background): the mouse, icons, windows, text, start menu, web browser, youtube videos, all. All the color and resolution stitching large and other than the fact that everything is great, the seams of the computer to function very well.

  I ran Spybot S & D, my antivirus software and Malwarebytes AntiMalware. Everything turns out to be clean.

  Okay, so, I tried to update my Device Manager display driver, and in the middle of installing Mobility M6, it is said: the file ati2mtag.sys on installation of ATI Technologies Inc. (VIDEO) DISC is needed. Type the path where the file is located.
  I n t have this I can not be completed.

  In any case, that s what I tried to do to solve this problem, but couldn't t. So I found this
  Windows XP Display Driver for ATI M-6 graphics card and its compatible with my model computer. Located here:
  http://virtualtech.Toshiba.com/ToshibaSupportSite/search.do?cmd=displayKC&docType=kc&externalId=2857 67xml & sliceId = & dialogid = 67910098 & stateId = 1% 200% 206 7908255
  I think that what I have to do is to install the above. Can anyone advice please?
  Is it safe to me, just download this driver and install it? Or is so dumb that it might mess up my computer? He says his self-installation.

  Thanks a lot guys for all the help in advance. I REALLY APPRECIATE IT!

  Hello!

  Search for this file on your HARD drive, then you have the path of this file, but if t can be found, reinstall the driver that you founded.
  To do this, you must not start in safe mode. Remove the old driver files in Control Panel > add or remove programs, restart and install the driver.

  On the sound of tck - tck, I can say that this results perhaps a faulty HARD drive. By controlling the Drive Fitness Test:
  http://www.HitachiGST.com/HDD/support/download.htm#DFT

  Good bye