Satellite A660 - 12 fall down during the update of the BIOS, start again

Similar Questions

• Satellite A200 - 1 GB block during the bios update - will not turn on

  Need help please, I was updating of the bios. And the process is stopped at: 2/18. I wait an hour and i decided to turn off the laptop. Know I can't turn on. Nothing happens. Anyone know how the recovery mode?

  Thank you

  (Sorry for my bad English)

  Josefa Hello,

  It sounds as if you of the BIOS chip was damaged during the attempt to update failed, and unfortunately this will prevent you from starting your laptop so that you can tyr to redo the update.

  In my view, that it will be necessary to bring or send the laptop to a Toshiba authorized service agent who has the equipment necssary to re flash your BIOS chip.

  Kind regards

• Satellite A660 - beep sound stuttering during the use of Player multimedia CD player

  I have a boring beep and stuttering (music is delayed momentarily every few seconds, type electronic interference noise) when using the media player or CD player. I took the laptop for a repair under warranty where they replaced the motherboard without success, they then informed me that they believed that it was a software problem, and a reinstall of Windows 7 was necessary if I've done the following with the recovery disks that I created in that order, results in parentheses;

  -restore the factory software (no change still beeps and stutters)
  -formatted the HD (initially, I thought that solved the problem but after beginning dload and install about 80 Windows updates the question came back)
  -formatted the HD once again (once more I thought that the problem has been resolved, but I heard the beep/stuttering only once or twice)

  Given this HD format takes 26 hours, I will not begin to dload/install updates including Windows 7 until I can try something else or have an answer.

  If anyone can shed some light on this issue, the noise is terrible review it was purchased as a unit of entertainment media playback.

  Thanks for any help in advance here.

  Post edited by: vite11i

  Where the beep from exactly? Speakers or elsewhere?

• Satellite A100 falls down during the video capture in first 6

  Hello!
  I have Satelite A100-153 - PSAA9E (DuoCore T2300 with ATI X 1600) and I'm trying to capture video (Premiere 6.5 of DV camcorder via firewire).
  Whenever I get bluescreen reportng PAGE_FAULT_IN_NONPAGED_AREA
  ativvaxx.dll - address BFDOF9F9...

  Anyone know what could be wrong? It is quite new instalation original (from recovery DVDs) with only Adobe Premiere 6.5 installed.

  All the best,
  Tom

  Hello

  I don't know if it will help you, but I found a useful Toshiba document on similar problems.
  Please check this:
  "By running Adobe Premiere Elements 2.0 laptop freeze or crash.
  http://support.toshiba-tro.de/KB0/TSB6401FS0007R01.htm

  Please post again if you have solved.
  concerning

• InDesign CC falls down during the boot process

  If CC InDesign lance, he gets up to a certain point before it crashes everytime at the same point.  It is 64-bit only, 32-bit is still in charge, but it's much more slow and terrible to work for me.  I am running Windows 7 and have all the latest cloud only indesign updates installed.  I tried to leave the application of launcer CC so TypeKit fonts not loading at startup with nothing helped.  I tried to use msconfig to a selective startup, do not load the startup items and restart and once again, no dice.

  

  Here is the full text of what you see the problem in detail in this screenshot of the window above:

  Signature of the problem:

  Problem event name: APPCRASH

  Application name: InDesign.exe

  Application version: 9.0.0.244

  Application timestamp: 5176f4c7

  Fault Module name: ObjectModel.dll

  Fault Module Version: 9.0.0.244

  Timestamp of Module error: 5176f4b9

  Exception code: c0000005

  Exception Offset: 00000000000261 c 0

  OS version: 6.1.7601.2.1.0.256.48

  Locale ID: 1033

  Information additional 1:9529

  More information 2: 9529754cc72c58f900e33c4f1855fb96

  3 more information: fe5f

  Additional information 4: fe5f55426fc3e5a2feae05a45cff6f40

  No problem. The bad news is that confirms that this is not a problem at the user level. I think you really need to uninstall CC, and then run the cleanup tool (CS for installation problems cleaning tool |) CCM, CS6, CS5.5, CS5, CS4, CS3), then reinstall.

• Smartphones from blackBerry Desktop Manager falls down during the synchronization of outlook calendar

  Today only has what is going on has begun - BB8320 synchronizes very well until the moment of synchronization of calendar (outlook 2003) I get this error message

  AppName: desktopmgr.exe AppVer: 4.2.2.14 ModName: ilxolk.fil

  ModVer: 5.5.1.246 Offset: 00060c 03

  have you tried re - start (laptop and phone), have the modified sync settings, but always crashes at the same point - form 23 of the 35 records.  Someone at - it ideas?

  Well, if the sync has gone well, you must have in your blackberry 22 items. Maybe they are stored in chronological order?
  Anyway, 22 out of 35, which means that there are more than 7 events that can cause the problem. just wipe everything and re-create them then!

  For the reason for the bug... here is maybe something at the event? an attachment, a special category...

• Urgent! -Adobe CC falls down during the process of "extract" of Photoshop, need to install the version full, without hollow CC

  I need emergency aid because Adobe CC crashes after the 'extraction' of an application process. So if I chose to download an application (Muse, Photoshop, etc.), download it and after that it crashes, is there any support available?

  Thank you

  Problem solved, it is the firewall that blocked the installation, everything works fine now!

• Animate edge falls down during the collage

  Hi all

  I use Edge animate 1.5. Until today, the experience has been great! Today, however, whenever I try to paste or duplicate something, I get the message "an error has occurred."

  Can someone help me?

  Thank you!

  Hi, Andrew.

  I was able to reproduce the bug on my side.  The good news (for me), it is already fixed in the latest version of Animate.  It happens also on Mac and Win, then you are probably impossible to escape.  That being said, there is another way to do exactly what you want to do: copy your item from your components panel or mounting and right-click in the same pane.  Select "paste special" > "Paste it all."  Your active and all transitions will be pasted as if you had selected "duplicate".  I just confirmed that the accident does not happen in this case.

  Thanks for the presentation of a report as detailed - it really helped to be able to reproduce the problem on my side.  I hope that the solution is simple enough to use in daily work.

  See you soon,.

  -Elaine

• ENVY 100 printer D410 - screen says "Do not, power down during the update" permanently.

  I'm a Mac user Mavericks 10.9.1 running on a Mac Book Pro.

  I have a HP ENVY 100 D410 printer that works your for a few years.

  Recently, the LCD screen of the display on the printer offered, "there is a new driver. You want to update? "(Yes/no)

  (Or something close to that.)

  Unfortunately, I chose 'yes '.

  The printer then tried to update, but eventaully the LCD screen on the printer displays a flashing message:

  "Do not feed, down during the update"

  The printer now flashes just this screen continuously. The LCD screen will not display anything other than this message.

  The printer works when connected by cable and wireless. (Airprint works very well).

  I can scan documents, I can print pages, I can even access printers "Web page.

  But the LCD touch screen control panel is 'stuck' in flashing update message.

  I can't find any way to clear this error and allow the printer to complete the update.

  Help. Please, I beg you.

  Hello

  There is a fix to resolve the specific problem, but I'm afraid it is only available for earlier operating systems under OS X 10.5 and 10.6, Windows XP, Vista or 7.

  I you suggest to get a computer with any operating system supported, install the latest version of the software on the HP site using a USB and then follow the steps.

  The latest version of the software can be found below (the basic software should be sufficient):

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?cc=us&DLC=en&LC=en&OS=4062&product=4073738&softwareitem=MP-92513-1&sw_lang=&

  Make sure that you carefully go through the procedure to the installation section in the patch download page.

  Hope that helps,

  Shlomi

• Message "do not power down during the update"control panel screen not fade.

  Product name: HP ENVY 100 e - All - in - One Printer D410a

  Product no.: CN517A

  The message "Do not power down during the update" on the control panel of the printer refused to erase and remained perpetually disaloowing acess the Menu home for other actions as photocopies etc.

  I see.  I found this utility that will help you to solve the problem.  It seems the printer lost connectivity during an update firmware and glitch out.  The utility should take care of it.  Let me know what happens.

• Satellite P100: Multiprocessor is disabled in the BIOS v4.20

  Hello

  I have just updated the bios to 4.20, after reboot, I went to the bios settings and saw that the multiprocessor (the option for the use of 2 CPUs) is disabled.

  After I enabled it, the computer is very slow, and I had problems with starting the computer.

  When the multiprocessor option is disabled, the computer works ok, but the Task Manager indicates that a single processor.

  I had to go down to the bios to version 4.00.
  I would like to know if there is another solution for this.

  Hello

  In front of me, I have Satellite P100-191. I did the BIOS update to version 4.20, and in my case, Multiprosessor is undoubtedly permissible. In this case, the entry in the Device Manager shows 2 processors.

  I disabled this option and the laptop runs slowly than before and in the device manager what a processor is listed.

  I don't really know what is wrong in your case, but I can confirm that the Satellite P100-191 friends, everything works well.

• Start of Windows to install updates and then fail, restores the installation then the cycle starts again.

  original title: I continue to receive updates for Windows. Updates begin to install fail, updates to day is awarded automatically installation and then the cycle starts again.

  This process takes about an hour, during which I can't use the laptop.

  Hello

  ·         Update is causing the problem?

  ·         You get the error message?

  Method 1:

  Try to install the update to the clean boot and check if it helps.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135/en-us

  Note: Don't forget to start your machine in normal mode by following step 7 of the link.

  Method 2:

  You can try temporarily turning on all security software and then try the updates again.

  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  Important note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 3:

   

  Also refer to this article and check if it helps:

   

  Problems with installing updates

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-installing-updates

• Re: Satellite Pro A200 - black screen after the BIOS screen

  Hello
  I'm new to the forum and have a big problem. So, any help is welcome and appreciated.

  My Satellite Pro A200 turns black after the BIOS screen and a black screen with a blinking cursor. Also just as the screen goes black a beep can be heard which shows windows boot.
  I can access the toshiba Setup screen but not the installation of security mode.

  Kind regards

  Hello

  You wrote that you can access the BIOS, but have you checked if the HARD drive is recognized properly? Perhaps because the computer cannot start HDD isn't recognized then you should check this.

  If the HARD drive is recognized, I would try a Toshiba Recovery disk recovery facility. It seems that Windows isn't able to start and if you reinstall the whole system should help get rid me of this. Go to the start menu and select the CD/DVD drive as a boot device.

  Check this box!

• After installing ElCapitan 10.11.4 on my G5, if I stopped for the night for some reason, the computer starts again sometime between 03:00 and 07:00. Any thoughts?

  After installing ElCapitan 10.11.4 on my G5, if I stopped for the night for some reason, the computer starts again sometime between 03:00 and 07:00. Any thoughts?

  Sounds like an Energy Saver preference, but what computer do you use?  A G5 (PowerPC) machine will not work on El Capitan.

• HP Envy stuck with message "Do not feed, down during the update"

  I tried to install the updates from the menu of the printer, but now he constantly says: "do not, power down during updates. He did all day yesterday until I have is growing impatient and returned it works, but still displays the message once it lights. This has now been reading all night.

  I read somewhere a hard reset would work, but can't find anywhere how to do this.

  Can I print a Network Setup page and page of test very well.

  I can get Internet access to the printer.

  I would like to be able to see the printer menus again please.

  Kind regards

  Mike.

  The solution obtained from the phone HP Service Center:

  Firmware update:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=MP-92884-2&cc=us&DLC=en&LC=en&OS=219&product=4073738&sw_lang=