Satellite C660-1CQ - graphics pretty tense horizantally after the installation of Win10

Similar Questions

• Satellite S50-B-15 q - two issues after the installation of Win10

  Hello

  I have a big problem with my "FN" key It's the switch... Normally I do not press "Fn" to increase volume, brightness... But since windows 10 I have to press "Fn" and me cannot solve the problem. I tried many solutions but no result.

  I also have the problem with the "Pc HEALTH MONITOR" application, while installation a displays an error message on the windows 'Does not support' and I can't solve the problem.

  Can you help me please?
  Thank you

  You updated the drivers and software for win 10 compatible version?
  Here you can find the Win 10 drivers that must be installed:
  http://win10upgrade.Toshiba.com/swup...SPX?region=TEG

  FN key issue:
  The special function mode button controls this feature of the laptop.
  You can enable or disable this within the Toshiba HWSetup or in the BIOS.

  More information:
  http://APS2.toshiba-tro.de/KB0/HTD2503B90001R01.htm

• Satellite A300-15 a does not start after the installation of the alcohol program

  Hello...

  Satellite A300-15 has, I bought yesterday and after completing the installation of Vista, I tried to install "Alcohol" but my judgment of the laptop and now I'm not able to boot up the laptop.
  It does not start in any mode.

  I forgot to make recovery disks. I think that alcohol is not compatible with Vista. Error I get is below.

  Can someone tell me the solution?
  Please help urgent

  "A problem has been detected and Windows has shut down to prevent damage to your computer.
  If this is the first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow these steps: blah blah... "

  Looks like a problem familiar to me, as I had the same one with the Daemon tools. After installing these tools, I couldn't start my Windows XP. I guess that it somehow mixed upwards of some drivers or registry entries, but not sure about that.

  OK, you can try to uninstall tool first start Vista in safe mode (press F8 before Windows starts upward).
  You should then be able to enter in Vista without problem.

• Satellite L670-11R - SD cards were not after the installation of recovery

  Hallo,

  After that I got a virus I couldn't find my SD cards in the workplace (I hope, be called 'place of work' in English').
  So I started the recovery of HARD drive and restore the system to the original terms.

  But now, I have the same problem:
  When I put an SD card in the slot, the dialog box in the lower right shows me, that the drivers have been installed, but I can't find my card. When I put the card SD and back, nothing happens... Only after reinstalling the card-slot-driver from the toshiba-homepage, I can see the dialog box by putting in the SD card. But even once only once and nothing else happens.

  So, I don't know if it's a hardware problem (the slot recognizes the card) or a driver problem (with exactly the same system that everything worked fine a year ago).
  Does anyone have an idea? If possible, please answer in German, if not, I would be very grateful for each answer.

  Timon

  Hello

  As far as I know the laptop L670-11R supports the Realtek card reader controller. I think you should try the Realtek Realtek driver page driver.

  Here you can find the latest version of the driver:
  * PCIE card reader driver for XP/Vista/Win7 *.
  http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=15&PFID=25&level= 4 & Conn = 3 & DownTypeID = 3 & GetDown = false

• Satellite U200-179 often does not start after the installation of Ubuntu Live CD

  I'm installing Ubuntu edgy on my new computer toshiba laptop U200-179.
  I install linux without problems from the live CD, but when I try to restart the pc, often it does not start.

  During booting linux runs the utility to check the file system, although it seems that everything is ok and the boot stops.

  I also tried a different distribution (Knoppix 5.01), but with this one, the installation process stops at the beginning.

  What could be the problem?
  Luca

  You have upgraded to the latest version of the BIOS available (3.30)? The previous (2.40) had problems with some Linux distributions...

• OfficeJet Pro K850: After the installation of Win10 print number

  After each print job, my printer now prints a page of "test" of bars, blocks and lines.  Takes a third of a page.  Big waste of time and ink.  Any help would be appreciated.

  Hi @jrbodell,

  Welcome to the Forums of HP Support! I read your post and see that the printer prints a page of "test" of bars, blocks and lines after each page. I would like to help you today. If this helps you to find a solution, please click on the button "Accept as Solution" down below in this message. If you want to say thanks for my effort to help, click on the 'Thumbs Up' to give me a Kudos.

  This problem occurs for one or two reasons, about power or a problem with the reloaded cartridges or one or several colors do not print

  I would like to do a hard reset to see if that will solve the problem.
  Let the printer and disconnect the printer cable and the wall socket for 60 seconds.
  Reconnect the power cable to the output of the printer and the wall, and not a surge protector.
  This ensures that the printer is full on and can help this situation.

  You use genuine HP cartridges?
  What are the ink levels?

  I would say to run a clean and clean the nozzle on the cartridges manually.

  If there is anything else I can help you, let me know. Thank you.

• Satellite C660 - 115 WLan connection only works when the power cable is connected

  Hello

  A few weeks ago, I bought a Satellite C660-115. I want to surf the internet anywhere in my house without any son/cables.
  On the first day, I had this problem: when I disconnect _power_ cable, the wireless connection will stop working.

  The Web page on my screen will always be there, but a new page loading is a problem.
  It is sometimes useful to recharge (by pressing F5), - sometimes not. It is always useful to "ip address of repair", but not for long.

  The only solution is to atach regardless of how much power the battery has still the power cord.
  When I do, it is no problem whith the connection at all.
  I went back to the store where I bought it, they related to their own wireless network and they have had the same problem after a few minutes. In the shop too attach the power cable solved the problem.

  So the problem must be in my lap top, not in my network (modem or almost).

  Doesn't this all seem familiar, and if so, how can I solve this?

  I hope that my English is understandable, I live in Holland.
  Thanks in advance!

  Here is the solution:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=59177

  Change options for saving for the Wlan in Windows 7 power management

• Problem starting after the installation of the NTI Echo Satellite P50-B-11V

  Hi guys. I have problems to start mid laptop computer (Toshiba Satellite P50-B-11V, F04236S) after the installation of NTI Echo3 to migrate the data from the drive HARD original to a new SSD (Toshiba 480 GB Q300 series).

  Error: file/echo not found boot/initrd.gz. Pilot pata-platform...
  Kernel panic not syncing VFS: Don't mount rootfson unknown - black (0,0).

  Anyone facing this problem? Please advice if you have the time.
  I tried several times to repair Windows (F12 key) and I have tried different ways to migrate data but the problem even after reboot.

  Thanks fo your time.

  Posted by marianbur
  

  Hi guys. I have problems to start mid laptop computer (Toshiba Satellite P50-B-11V, F04236S) after the installation of NTI Echo3 to migrate the data from the drive HARD original to a new SSD (Toshiba 480 GB Q300 series).

  Error: file/echo not found boot/initrd.gz. Pilot pata-platform...
  Kernel panic not syncing VFS: Don't mount rootfson unknown - black (0,0).

  Anyone facing this problem? Please advice if you have the time.
  I tried several times to repair Windows (F12 key) and I have tried different ways to migrate data but the problem even after reboot.

  Thanks fo your time.

  Dear marianbur,

  New laptop having same problem here, is now stuck... Have you received still no solution?

  Greetz

• Satellite P100-119 - software after the installation of recovery

  I use a Toshiba Satellite P100-119 since 2006. I want to run the original liveries Product Recovery CD after you back up all my data, so that with a vacuum system, the laptop gets even faster.

  But as there were pre-installed software (office, Toshiba programms) when I bought it, I don't know if they went after the recovery. I do not have CD for these programs, they were just pre-installed and what my Windows xp, should recover fully with the cd?

  Hey Buddy,

  After the installation of recovery, you have the same settings that bought the laptop. With other words recovery disk will restore the box settings.

  Firstly the recovery disk will wipe the entire HARD drive and remove all. After this Windows will be installed all the drivers and tools. In addition, will be also installed software preinstalled such as office, etc. and you can use it again. :)

  Backup all important data like the photo, music, etc. but everything will be removed for a clean install of Windows.

• big problems after the installation of Yosemite (10.10.2) with Photoshop CS6... The program crashes - last time 10 times during my working session... wacomtable does not work... It's slow... and receive errors on the graphics card... It s a terror to work

  big problems after the installation of Yosemite (10.10.2) with Photoshop CS6... The program crashes - last time 10 times during my working session... wacomtable does not work... It's slow... and receive errors on the graphics card... It s a terror to work with my beloved Photoshop!

  Yosemite upgrade very often damage existing Photoshop.  I thank Apple for that.

  You must uninstall and reinstall Photoshop, then apply all the updates of Photoshop from scratch.

  But first, give us details about your configuration:

  STANDARD TEXT:

  Note that it is standard text.

  If you give complete and detailed information on your configuration and the issue,

  as your platform (Mac or Win),.

  accurate versions of your operating system, Photoshop (not just "CS6", but something like CS6v.13.0.6) and the bridge.

  your settings in Photoshop > Preferences > performance

  the type of file you were working.

  specifications of the machine, such as total installed RAM, scratch file HDs, total available disk space, video card specifications, including total VRAM installed.

  What troubleshooting steps you have taken so far

  what you receive, error messages

  If problems of opening raw files also the exact camera brand and model that generated

  If you experience problems printing, specify the exact brand and model of your printer, the size of the paper, the dimensions of the image in pixels (so many pixels wide by pixels high). If going through a TEAR, specify that too.

  A capture of your settings, or the screen image could be very useful also,

  etc.,.

  someone may be able to help you (not necessarily this poster, which is not a Windows user).

  Read this FAQ to get advice on how to ask your questions correctly to get faster and better answers:

  http://forums.Adobe.com/thread/419981?TSTART=0

  Thank you!

• Satellite L655 touchpad button ON / OFF does not work after the installation of VAP

  Why the Start button / stop the touch pad does not work after the installation of vap?

  May I ask what system and what PPV version do you have installed?

  I assume you mean on the Fn + F9 key combination...
  Is this right?

  Another FN button work as shouldy?

• Satellite L555 - 10K - FN keys do not work after the installation of Windows 10

  I installed 10 64-bit Windows (original was Windows 7 64-Bit)

  My FN keys do not work after the installation of Windows 10.

  There is no possibility of a screen-Switch, and the brightness setting and activate Touchpad...
  Do you know any help

  Hello

  I think that your model of laptop is not possible to Win10.
  Check it please https://forum.toshiba.eu/showthread...mation-website

• Audio does not work after the installation of Vista on Satellite Pro a series?

  Done a format and a new facility with vista ultimate and can't get the audio from realtek to work.
  The drivers install properly but don't have still no sound.

  Download realtek 97 and drivers HD, but still no luck.

  I had this problem some time and fixed it but I can't find where I found the solution of :(

  Any help would be great, thanks!

  Hello

  First if all would be very useful to know which model of laptop you have.
  Second, you could find the driver of his right on the page of Toshiba and so you n t need to test several audio drivers! The one on the Toshiba driver site works for sure.

  I read about a similar problem on Vista OS and these Toshiba document should help you:
  [Audio cut off (no sound) after the installation of Windows Vista: http://askiris.toshiba.com/ToshibaSupportSite/search.do?cmd=displayKC&docType=kc&externalId=1886 758xml & sliceId = & dialogid = 54568603 & stateId = 0 0 51373343]

  Check it out!

• Patches of Toshiba Service Station closes after starting after the installation of 3

  Hello

  We recently have a "patch day" Toshiba Service station. I think from my memory that the patches are released earlier, but I installed them on April 23, 2010. There are three patches, and so that I can restore from the system recovery, it was:

  -Flashing of BIOS
  -Patch HDD/SSD Alert
  -HDD Recovery patch.

  So, not to mention that I had problems to make the flashing patch BIOS to run, finally extracting installation files to another location and run it with administrator rights.

  My problem is that after this session of patch, my Toshiba Service Station no longer starts. When I start my system, after recording on it seems to start upward but always farm then again with windows say error report 'stopped working' and that's it. I'm not sure patch who this could be. I also believe that one of these Islands said in the description that it will update station itself? I downloaded Service Station on the Toshiba site but it will not prove at best, does not matter if I uninstall it, before you start the installation with administrator rights or not.

  My system is Satellite A500, Windows 7 64 bit.

  I hope you can help. Unless I can't access the updates anymore!

  Note: A few days before I installed a graphic driver for my Nvidia GT 230 m SINCE THE SITE WEB of NVIDIA. Why am I? I've lived literally all HOURS a unwanted system reboot and I see in the problem report it was always because of the graphic driver. Subsequently, I installed the two patches from the site of Toshiba, the elders and the most recent, but the problem persisted. Fortunately, a few days I have recheched the Nvidia site and there was a new driver.

  Although he said BEFORE (not now anymore) that this graphics card should be based on a driver manufacturer, I installed it but because he Coulnd't ' t get worse. The positive thing is that I didn't have a single far system crash even if I leave the phone turned on for hours.

  I'm not sure if the problem with the gas station started right after the installation of the graphics driver, but it can't be because I installed the three patches mentioned above, through gas station, a few days later.

  But he seemed to have affected the software after these patches? I'm not sure.

  Hello

  Simply said; Toshiba Service Station breaks down and new installation of this tool didn't help.
  Right?

  Well, because you are not sure what s wrong and depending on the assignment, you have other problems with the software, I recommend to recover the laptop using the recovery of HARD drive option!
  This will outline the laptop to factory settings.

  Of course, you must back up the data if you have important files.

  Run recovery disc HARD and after that check how the laptop would serve!

• Loss of FN - key after the installation of the updates from Microsoft on L500 security

  I am using a satellite L500-19U

  After the installation of Microsoft security updates the FN lost their function except the brightness keys + /-function.
  also the function keys that appear on the upper border of monitor by pressing the FN key appear after the security packages have been installed.
  I solved the problem by removing the update through the function of W7 (Wiederherstellungs punkt) back.

  The following security packages are selected to be installed:
  Update security for Windows 7 for x 64-based systems (KB978601)
  Update security for Windows 7 for x 64-based systems (KB979309)
  Update security for Windows 7 for x 64-based systems (KB979683)
  Update security for Windows 7 for x 64-based systems (KB980232)
  Update security for Windows 7 for x 64-based systems (KB981332)
  Windows MRT x 64-April 2010 (KB890830) (malicoius software removal tool)

  Which of them are unsuspicios, which must be postponed, the updates are necessary after installation, updates?

  Post edited by: JoJo58

  Hello

  If you read about these update on the Microsoft website: (not of them should affect the FN keys)

  http://www.Microsoft.com/downloads/details.aspx?displaylang=en&FamilyID=998164b7-4B8C-468B-8d39-f242633c8838

  I checked the history of updates on my computer and all of them are installed with the exception of Windows MRT x 64-April 2010 (KB890830) (malicoius software removal tool). Everything works correctly, try to remove this update.