Satellite C660D 15F - black screen after startup

Similar Questions

• Satellite C660D (PSC1YE) black screen after BIOS update

  I tried to update my Bios on my Satellite C660D portable (psc1YE) last week (big mistake).

  Something went wrong during the update and now when I power on I just get a black screen (LEDS and fan).

  After reviewing, the conclusion is that I damaged the BIOS that must now be blind flashed.
  So I got the hand on a 512MB memory stick, formatted using FAT through windows XP and used Wincris to create a startup disk after you have added the file bios.rom (renamed Bios.wph) which I extracted the last update of the BIOS on the Toshiba site.

  My memory stick has three visible files on it, Phlash16.exe, bios.wph and minidos.
  I plug laptop with battery, DVD player and power disconnected to stick, and hold Fn + B re-connection cable cable, turn it on.

  The fan whirs at full speed, and the USB lights up and flashes then for a minute, as if being read. No matter how long I let on, the fan will continue whirring and the USB is on and when I unplug and put in still works a black screen.

  I tried different sticks, (up to 4 GB with FAT32 format), programs of different startup (for example, the HP utility) drive but still no luck.

  Can someone tell me what I do wrong? I tried to look for a newer version of Phlash16 just in case that was the problem, but can not find one any where (mine is version 2008)

  All advice would be greatly appreciated even if it's just to tell me that I'm wasting my time because the pc is not repairable.

  I can't tell you if you waste your time or not because I n know if the motherboard ROM module is OK or not

  In most cases, it should be possible to reflash the ROM module using the BIOS crisis disk but this disc is available to authorized Toshiba service technicians and as much as I know reflash this methods is not always the same

  However, in some cases it might be possible that the mobo could not be fixed by disk crisis, it would be the worst case

  I recommend you to contact a certified maintainer Toshiba to check guys would be able to use the crisis disk and could test whether its possible to reflash the module ROM
  Is it not would be not possible well in this case you would need new motherboard :(
  But lets hope do ' t you need...

• Satellite C660D-1F2 - black screen after BIOS update

  Hello

  I have download the Bios Toshiba by writing my serial number for my laptop.
  First I checked my current bios and it is 1.5 I think. The news was 1.60. I flashed on WIN 7 64 bit
  First he checked, he erased and then he wrote after the writing process, the laptop is a reboot automatically. But after that the laptop closed and propelled again, he stuck to a blank black screen. Fan, CD Rom, keyboard worked. I think too many USB because when I connect my phone to the laptop, my phones battery charge. Please I need help. I am out of warranty.

  What I've tried so far:
  Take out the battery
  Power cable plug out
  Hold down the power button / stop 1 minute
  Connect the power cable to rear
  Press the Power button
  Solution: Same; Black white screen

  Satellite C660D-1F2 (PCS1YE)

  Hello

  I'm afraid that something goes wrong with the update of the BIOS, and now BIOS is damn Mr. usually in this case you need professional help from Toshiba service but it can be quite expensive.

  On this forum, you can find many discussions where people have described the same problem. Some of them have been able to solve this problem. a very interesting thread, you can find here. Check it out please.

• Satellite Pro U200-> black screen after startup

  Hello

  It happens from time to time when I try to start my PLUA1E Satellite Pro U200-02802QS4, then I get a black screen even from the BIOS.
  What is wrong and how to fix this?

  BTW, I already have this BIOS version: P0044v370.exe installed.

  Hello

  This happens from time to time?
  This means that you can not reproduce this problem?

  Hmm that's not easy to say what the issue might be.
  Maybe the BIOS update will help you at the moment you can find BIOS 3, 7 victory on the European driver Toshiba page.
  If you have a lower BIOS version installed, then I recommend an update.

  It is also possible that this problem is related to some of the material; motherboard, screen, etc.
  In this case the part should be replaced but first of all it of necessary to know what part is affected and I think that the technician of the ASP for this

  What do you think???

• Satellite L500-1XJ - black screen after startup

  We have a portable Satellite L500-1XJ that our 3 year old got to and pressed the buttons on the key board. Now when you turn it on the screen gives aflicker then rest dark.
  I tried FN + F5 and FN F7 to see if it was passed to the external screen or brightness was rejected, but makes no difference.

  Do you have advice as to how I might be able to solve the problem?

  > Now when you turn it on the screen gives aflicker then remains grim. I tried FN + F5 and FN F7 to see if she was reactivated on the external screen or brightness was turned down but
  > makes no difference.

  It looks like serious problems with the related material to the mobo (vga). You can access Bios at startup, or the display is just dark? External monitor is connected to the laptop?

• Persistent black screen after startup on Satellite Pro A210 (PSAFHE)

  Need help, need advice on how to solve a persistant problem with black screen after put into initial service.

  Initially its fine but after the initial Toshiba of the screen just goes black, and the rest in this way, the PC stays on. Have you tried F8 options but all result in the same.

  Help please.

  Hello

  You can access the BIOS by pressing F2?
  Boot from a boot as Recovery DVD disk?

  If both is not possible, I'm afraid you have a serious hardware problem m.
  In this case, I get just speculate on the affected parts. Maybe his problem GPU or motherboard who knows

• Black screen after startup - Satellite A105-S4334

  It gives me black screen after the display of the logo just after the appearance of the cursor and nothing I can do except hold the button 'Disable' of windows, and then restart again, it shows the menu to make it start in safe mode... network mode... normally or lastest know good windows start...

  When he starts for the second time it works very well, he does it all the time and now I'm reinstalling windows for the 2nd time (factory State) any solution or explanation for that matter?

  Hello

  It is not easy to say why this is happening. Have you standing connected an external device, such as USB, printer or something similar?

• Corrupt BIOS V5 531 Acer black screen after startup, f2 and f12 also. Repairable?

  Hello

  Yesterday I tried to install Win 7 if I could play D & D Neverwinter on Arc after using * nix systems study (looking to start a career as an administrator). I had plugged into a power strip that was, unbeknownst to me, turned off and I went to make coffee and watch some news. When I came back to check the progress of my laptop was powered off and since then I havn't been avle start without being blocked at a black screen after the start page of the bios. The f2 and f12 also leads to a black screen, I can not change the boot device or enter the bios Setup.

  Is - fixable at all? For example, is the a key-combo, I can use it to restore from a backup bios? Or, do I have to bring in a technician who can install a new chip bios or flash this old some how? Or did I brick pemanently my device?

  V1.22 is what you want to be part of a unit of Windows 7.

  The problem is if it crashed during the upgrade process, it will take some special tools clearly on the chip on the MB and recharge it with a new BIOS. I would contact your local support team to see what options are available.

• Black screen after startup for 30 sec as if my network is enabled.

  So my problem is that I mentioned above. If I disable my router with its button to completely close and bad to start the computer, my PC starts in 5-7 seconds.

  If I turn on my router my PC goes black screen after the loading screen logo of blue windows and wait like 30 sec or sometimes 1 min, before sharing the login screen.
  I tried to make my static rather than dynamic, same IP occur.

  Hello

  Thanks for the updates.

  Did you check with the router manufacturer to see if the firmware updates are available for the same?

  Since the problem started once you have this connection, you must get in touch with the ISP or router manufacturer to check the issue.

  Hope the helps of information. Let us know if you need help with Windows related issues. We will be happy to help you.

• My Satellite L505D goes to a black screen after startup

  It seems to boot up properly and everything. It starts Windows 7 and goes to the user selection screen, but since there is only 1 user, it only says: Welcome to the loading circle. But when he tries to load the page office or home or whatever you call, all that happens is the mouse.

  I can move the mouse normally, my anti anti-virus pop ups see the place if necessary. On my last attempt to try to solve the problem, I got my user to open the file, but has happened automatically. I tried taking the battery twice thing. If any ideas on why the screen just looks like a black screen and the mouse visible.

  PS: I use the keys ctrl + alt + del function to get these options appears.

  On this virtual path, it is not easy to understand why all this is happening, but what you can try is to start the operating system in safe mode and roll back the OS to an earlier time to see if it works.

  Can you please try this and post comments.

  Do as a first step. Later, we see what can be done.

• Satellite A215-S7422: black screen after ATI driver installation

  Please help me. I buy the Toshiba Satellite A215-s7422 laptop and install Windows XP.
  After that I have download the driver for ATI Radeon x 1200 and install. After you reload a see black screen.

  Hmmm on which site did you download and install the ATI graphics card driver?
  The laptop seems to be produced and designed for the American market. That's why drivers should be downloaded from the Toshiba site we!

  In any case, this problem seems very strange. In my opinion, you used everything simply wrong driver.
  Try to start in safe mode using the F8 key at the beginning of the startup procedure and remove the graphics driver.
  If this does not help, try to install the operating system using the Toshiba Recovery CD!

• Re: Satellite Pro A200 - black screen after the BIOS screen

  Hello
  I'm new to the forum and have a big problem. So, any help is welcome and appreciated.

  My Satellite Pro A200 turns black after the BIOS screen and a black screen with a blinking cursor. Also just as the screen goes black a beep can be heard which shows windows boot.
  I can access the toshiba Setup screen but not the installation of security mode.

  Kind regards

  Hello

  You wrote that you can access the BIOS, but have you checked if the HARD drive is recognized properly? Perhaps because the computer cannot start HDD isn't recognized then you should check this.

  If the HARD drive is recognized, I would try a Toshiba Recovery disk recovery facility. It seems that Windows isn't able to start and if you reinstall the whole system should help get rid me of this. Go to the start menu and select the CD/DVD drive as a boot device.

  Check this box!

• Satellite L350D - 11K: black screen after downloading the Tempro updates

  Hi Forum,

  yesterday, I admitted Tempro download several updates on my satellite L350D - 11K.
  During the last update, it was an update of the firmware, the system crashed, and it no longer starts.

  After removing the battery, the system starts up, but now it has a black screen and I don't know what to do.
  Pressing any key F doesn't show any results and I have no recovery CD.

  Does anyone have an idea what to do?

  Thxxx in advance

  Hello

  I don't know why it happened, but if the short workaround solution posted by boarder will not help, so I see good opportunities to contact the ASP in your country for assistance.

  > During the last update, it was an update of the firmware, the system crashed, and it no longer starts.
  You're talking about the firmware update
  Maybe it was a BIOS update which failed and so the laptop will not start again
  As already said in this case that only the ASP technician could help you.

• Black screen after startup (no home screen)

  I was just with the Firefox browser, looking for patterns (no piece, first... use airplane mode and not wifi) and when I clicked on the cog icon in Firefox the buggy device. He showed me a message saying that the home screen has crashed. Now the device boots (displays the logo of LG, the animated Fox, my carrier logo (Vivo, of the Brazil) and Firefox OS logo, but it goes to a blank screen (it is actually a black screen with high bar appearing, showing that it is on that plane and battery.) If I press the home button (or hold it) the phone vibrates, but nothing happens. If I pressed the power button a menu appears with: "Turn airplane MODE" (which is annoying because it is already on, but if I choose what to disable), "Silence incoming calls", "restart", "Power Off". There is the option "Cancel". Each of them works, but I don't know what to do.
  Oh, I tried to bring together the power, them increase the volume and the buttons on the home screen when the phone is off, but nothing happens. It turns when I release the home button. In addition, the volume and lock (or power) buttons works and change the volume / locks the phone...
  What should I do?

  The phone is a LG Fireweb, bought in the Brazil.

  Update, I tried to discount backwards, looks like you need the power, the House hold and volume KEYS until the LG screen appears, then release them. Worked well after the reset (so far).

• Satellite C55-B5101 - black screen after Windows update

  Mobile received Christmas day (all new) Satellite C55-B5101, saves Windows update (formerly 8.1) by getting only now black screen... Not very in computers so if you know what please he dumb down for me! Thank you

  Hello.
  I'll post a similar problem with mine. Here is something I've read elsewhere that can solve yours.

  Unplug the cable from the main charger.
  Remove the battery if possible.
  Press and hold the power button for 1 minute.
  Leave battery and connect the cable.
  Turn on.