Satellite L30-113 cannot start Windows OS

After downloading upgrades my computer does not start at the top. My computer screen shows a black screen, red, writing in the middle. He then goes to the screen, then go to windows error recovery page when you press on enter too lance beginning repair it then repeats the process and also switches its self off when you press start windows normally. I can't find the boot disks, the laptop is a Satellite L30 - 113 series.

Mary Anne.

Hello

I had a similar problem on my computer but was able to fix it.
I took my CD of Win XP and started the repair console.

Then I used the command Chkdsk and scanned and repair files and sectors on the HARD disk.
Then I used the Fixboot command. He writes a new boot sector on the system partition.
Finally used Fixmbr command that repairs the boot partition's master boot code.

Check out this page of MS:

[How to install and use the Recovery Console in Windows XP | http://support.microsoft.com/kb/307654]

Good bye

Tags: Toshiba

Similar Questions

  • Satellite A660-158 - cannot start Windows

    Toshiba Satellite A660-158

    I bought a laptop Toshiba Satellite A660-158. It has served me less than a week. I think it's the broken hard drive.

    My problem:
    Once I start the computer, it started and has worked for a while, but suddenly, there was an error reading that I didn't have the time. Computer has been restarted. And does not load... Until the boot mode does not reach. But the initial test (with logo) succeeded. Takes a long time and finally gives an error:
    -----
    Cannot start Windows. Maybe it was because of the recent small difference is the hardware or software configuration. To fix this error:
    1. Insert your Windows installation disc, restart the computer (the complete transmission wasn't)
    2. choose the language settings, and then click Next.
    3. Select "repair your computer".
    If this disk is missing, contact your system administrator or computer manufacturer (he turned and said to wear to the DEPOT, but I do not have this feature).

    Status: 0xc000000e

    Details: Unable to start menu, since the required device is inaccessible.
    -----
    Please help me! Idon't know what make me)
    Please write to E-Mail: [email protected]

    Post edited by: HunterS7777777

    Hey,.

    And why do you think the hard drive is faulty?
    Have you ever tried the repair your computer option? Usually with this option you can restore factory in a few minutes.

    Also if you have the Toshiba recovery disc you can also restore the factory of this disc. Just boot from it and follow the instructions on the screen. You need to do a few clicks only, installation with all the drivers and tools happen automatically.

    If you have any other questions, please let us know! :)

  • Satellite L30-113 - cannot burn CDs or DVDs

    I have a Satellite L30-113. Recently my driver failed for my dvd player, until I was able to install a few things and burn CDs and DVDs. Now, I can't record CDs or DVDs.

    Nero and CDBurnerXP for CD/DVD ROM say 'cannot continue burning process as you did not choose the device for recording. CD/DVD ROM propities shows that it does not support recording CDs and DVDs.

    I uninstalled the driver and restarted my computer and it reinstalled the same as that which does not once again. I am a driver update search and xp tells me that the driver is up-to-date. I checked the Toshiba updates with none of these updates for CD/DVD ROM.
    I have no idea on how to fix this unit "corrupted".

    Hi mate,

    I had a similar problem on my Toshiba laptop. So here, I searched a little bin forum and I founded to delete upper and lower filters in the registry. I followed the instructions in this Microsoft article:
    http://support.Microsoft.com/kb/314060

    After that, I again was able to burn DVDs.

    In addition, updated driver from CD/DVD isn't necessary because this driver is part of the operating system.

  • Satellite L30-11 - cannot start with drive HARD 750 GB (Sata II)

    Hello world

    I want to move to the size of the HARD drive in my laptop satellite L30-11th 120 GB at 750go (seagate momentum).

    I mist update BIOS firmware to the latest version (on the Toshiba site: V 3.1).
    When I start a press the F2 key at the same time, I can access the BIOS that shows the HARD drive. However, when I try to go further and to boot on the Windows 7 installation disc, nothing happens (although it does not start when I put the original 120 GB HDD).

    I have another (also Sata II) 320 GB HARD drive that works well.
    So, it doesn't seem to be a problem of Sata, but more a question of size?
    Any idea what it could be?
    If it's a question of size, how I can fix my pb?

    Thank you very much in advance for any help that you could give me

    Re

    Jérôme

    In my view, there is compatibility problem. Maybe you should not go over Board with upgrade of the HARD drive.

    Buy a HARD drive with a reasonable capacity. 400GO not enough for you?

  • Satellite Pro C650 - cannot start Windows more

    I have a Toshiba Satellite Pro C650 11Z model under Windows 7 Home Premium. I'm not very savvy computer. I can use my computer to perform tasks and use the software, but I m not very got when it comes to computer and tinkering under the hood, somehow.

    I was using the laptop yesterday evening to watch a You Tube playlist and was downloading a PDF 29MB file in the background. I have done this kind of thing before and never encountered any problems.

    When the download finished (I use Google Chrome) I clicked the button at the bottom left of the screen to open the download. You Tube then frozen.

    I could see the little green circle spinning around like loading upward download, but nothing was happening. Then Google Chrome no longer according to the bar at the top of the window.

    I tried CTRL + ALT + DEL, but the workload Manager wouldn t. The only thing I could do was turn off the laptop and running again, as it had frozen him completely. When I turned on it again, I had the Windows error recovery menu as shown in the following image.

    http://www.TechJaws.com/wp-content/uploads/2010/03/Win7-error-recovery.PNG

    The problem is that none of these options does nothing. If you choose the recommended option (for example Startup Repair) it comes up with the gray bar saying Windows loads the files and then will just a black screen. By selecting Start Windows normally gets you to the swirling colorful circles that make up the logo Windows and he said: start Windows but still once, it does nothing but just stick to that.

    A friend told me that a BIOS reset * may help. However, I don't know how to get the BIOS on the laptop. He called Insyde H20 installed and I don't see the option to access the BIOS.

    Someone at - it ideas as to what could have wrong and how can I fix? I don't have a recovery disc as my laptop was bought for me by a charity. The warranty has expired now so that I can contact t their support line.

    To be honest I don't think BIOS has nothing to do with it. Start your laptop and press F8 several times to display the advanced startup options. You will find the option to start the operating system in safe mode.
    If please test and let us know what happen when you try to do.

  • Satellite C650-1CP - cannot start Windows

    My C650, running on Windows 7 could not start properly today. When turn on/off he went to the Windows Error Recovery screen and gave me two options: run a startup repair and start Windows normally. I clicked on the repair option and on the bottom it says windows is loading files, then it's another loading screen, and finally to a black screen, which, after a few seconds, a cursor appears. No matter how long I left my laptop on nothing changes. So I decided to choose the second option, and he went to the splash screen windows with the logo of the movement. This form lasted around a minute, and then a blue screen with an error, which is then passed to a black screen. To see this error, I completely disabled the auto reboot on system failure in the F8 options and once restarted, he took me to the same error page.

    On the blue screen error was as follows:
    UNMOUNTABLE_BOOT_VOLUME

    She was followed by information saying that it's maybe a software / hardware problem and also to try safe mode.

    Technical information at the bottom were the following:

    STOP: 0X000000ED (0XFFFFFA8003DDFA50, 0XFFFFFFFFC0000185, 0 X 0000000000000000, 0 X 0000000000000000)

    I don't have a recovery disk, if I looked on websites have said recovery is built in. I also tried safe mode, repair your computer, last known config and other options in the F8 key, but these do not properly load and I end up on the black screen with a cursor again.

    I had originally to Exchange my laptop in a week to buy it because it was defective and I had a little less than 11 months, I wonder if there is a solution to this problem and also know if I am covered under warranty for this problem. Thank you.

    Hey,.

    Bluescreens are mainly problems of software or drivers so I think that reinstalling Windows would help to get rid of this.

    Why you don t have a Toshiba Recovery disk? I mean in the user manual it clearly written that you have create such a floppy yourself and it only takes a few minutes and you need to blank DVDs. All that s.

    The recovery disk contains an image of the settings from the factory with all the drivers and tools. It is an image pre-tested by Toshiba so everything will work after the installation of recovery. With this record, you are on the safe side.

    Anyway, you can order a recovery disc here:
    https://backupmedia.Toshiba.EU/landing.aspx

    Software problems are not covered by the warranty. Of course, you can make the laptop to an authorized service provider and guys are going to reinstall to factory settings, but you have to pay for this service.

  • Satellite Pro M200 - cannot start Windows

    I have a Satellite Pro M200 PSMC4A, did an update Windows, requsted to restart, then the black screen as follows:
    Windows could not start. A recent hardware or software change might be the cause. Equip the installtion disk and restart. Problem 1: having no disk - lost I think. Lost file is \Boot\BCD.

    Tried different legal remedies without success. Disk Windows XP used to reinstall but now says cannot see all hard drives!
    All of the suggestions.

    Hello

    You can access the advanced boot menu? If so, you should try to start in charge more than the last known good configuration.
    If this is not the only option is to reinstall Windows I think. Therefore, you can take a Microsoft or Toshiba drive. If you don t have the Toshiba disk recovery, contact the service provider authorized in your country.

    I think that the recognized HARD wasn t disc because you need SATA drivers. Did you check that?

  • Re: Satellite A100-410 cannot start Windows XP

    Hello

    I have a Satellite A100-410 and I can't start over (in safe mode ok). When starting, it shows the XP screen and after 10 seconds, the screen goes black. We have re-installed XP but no use. We checked again and assume that something is wrong with the video card drivers.

    So we checked for the last but no use. I can boot the laptop when the video card is uninstalled, so it takes to cause something weird.
    Or could it be that the card is broken?

    Hello.

    For sure your video card is ok, otherwise you may see white screen after switching on. The problem is in the driver problem. Have you downloaded the Toshiba site display driver?
    Maybe there is a conflict of driver. This site http://downloads.guru3d.com/downloadget.php?id=1655&file=7&evp=c14f9f3787877ee f9ef4b235b9146e96 stage
    Download and install. Then try to reinstall the display driver (if not work, do it in safe mode).

    If she's not always you help, do a search for a new iso Windows Xp but not Windows assembly (some guys like to change windows, deleting and adding some files, and then load it. Most of these modified versions are bad).

    That's all I can suggest now, sorry if does not work.

    Welcome them

  • Satellite L755D-10J - cannot start Windows

    Have had bad laptop free for about 20 months but now me black screen with white writing directed
    "Windows Boot Manager" Windows could not start. A recent hardware or software change might be the cause. To solve the problem: 1. Insert your Windows installation disc, and then restart your computer.
    I don't have the installation disc, as it was preinstalled. I tried the method "press and hold the zero button and turn on" but just to get the above screen again. I can lift the F2 and F12 menus and put everything back to the default value, but always end up returning to the screen "Windows Boot Manager".

    Any advice would be greatly appreciated.

    Please visit http://aps2.toshiba-tro.de/kb0/HTD1303440001R02.htm
    You will find an exact explanation how install recovery image and have an operating system preinstalled clean again.
    Doesn't work for you?

    Use of the zero button at startup is for American models.

  • Satellite A500-1GL - cannot start Windows

    Hello

    I was rebuilding my laptop with a new installation of Windows 7 64-bit and after all was in charge he has restarted and sitting at the prior loading screen that says "HARD BBS-disk Boot" it used now to go further than that. Also, when I look at the BIOS settings, I lost the ability to boot from USB, which is how I loaded W7.

    The problem is everything I try my laptop bluescreens OR it just sits at BBS-HDD.

    I even tried a copy of XP that I had, but nothing seems to work. (This is what the blue screens laptop)

    Is anyone able to help me with that and it would be useful to buy Toshiba reinstalling drive because I don't have the original I did.

    Any help would be greatly appreciated

    See you soon

    Tracy

    Hello

    Have you already tried to install Windows from the Toshiba Recovery disk? It contains a pre-tested image of factory with all the drivers and tools, so it should always work.

    If not it material s serious malfunction and you need assistance from an authorized service provider.

  • Cannot change the size of the video memory in Satellite L30-113

    I have a Satellite l30-113 which has 1 GB memory and windows Vista.

    The size of memory that has been attributed to the vga is 319 MB.
    How can I decrease the video memory?

    Hello

    do you really mean 319MB? This machine only supports a maximum video memory 256 MB shared memory. So if you might have 32 MB (which is how I imagine rather memory assigned to your VGA) you can increase the video memory of this machine by changing the value of memory assigned in the bios of your machine.

    Do you know how to enter the bios?

    Welcome them

  • Satellite L40 - cannot start Windows

    Hello

    hope you can help, my computer Toshibal L40 laptop on commissioning began by displaying the following error message:

    * "Cannot start Windows. a recent change in the software hardware might be causing... » *

    It offers the possibility of:
    "* Launch Startup Repair option" * "

    I chose this. WIndows seems to load up, but then I get the following error message:

    Installed program cannot start. Click OK to turn off the computer *.

    I lost the recovery disk, but attempted to load the recovery console by using a windows XP disk, but it gave me error message more. Advice would be very welcome.

    For the installation of Vista you don't need SATA driver but for Windows XP Home edition you need. Is no problem at all.

    The question is what you want to do now? If you want to use Vista just use recovery media and you will have factory again.
    No problem at all.

  • Satellite L300-19F starts not-cannot start Windows

    My mobile no dΘmarre, "cannot start Windows. "To solve the problem: restart with the recovery CD.

    I can do that, but first of all, I don't want to try to save the data (and photos) from a hard disk.
    Is it possible, for example, go to BACK when booting with the recovery CD, and copy the data on USB?

    Furthermore, all my data on E:\ partition. Will be crushed it during the installation of recovery?

    Please notify. Kind regards.

    > Is it possible, for example, go to BACK when booting with the recovery CD, and copy the data on USB?
    No, it is not possible!
    If you should start up using recovery disc then the recovery process would be started and the whole HARD disk may be formatted!

    You can try to start by using a WinPE
    http://www.LiveCD.com/

    This allows you to start the device and access the data on the HARD drive

    You could also build own Windows live CD
    Check this box:
    http://www.MakeUseOf.com/tag/how-to-create-your-own-custom-Windows-Live-CD/

  • Transmision very slow Satellite L30 - 113 (33rd PSL) LAN file

    Hello world!

    After upgrading OS from Vista to XP pro work LAN Ethernet very slow (transfer of files of 100 MB, 2 hours).

    XP-drivers downloaded from toshiba - Europe.com, for model Satellite L30-113 PCL33.

    Maybe I should applay patches?
    Also I can't use the PC card slot...

    Hello

    The transfer of data should be the same under Vista and XP.
    I think that you have installed an antivirus that scans all files during data transmission.

    Please disable it!

    By the way;
    If you notice a slow, data transfer Windows Vista try disabling Remote Differential Compression
    To do:
    -Start-> Control Panel-> programs and features
    -Click on Turn windows features on the left side of the screen on or off
    -Off remote differential compression

  • Satellite L30-113 - no sound after the downgrade from Vista to XP

    Hello to everyone.
    I recently bought a new laptop Toshiba Satellite L30-113
    with vista preintalled.

    As many users around the vista of the world seemed very slow for me so I decided to go back to Windows XP Pro.
    The problem is that I can't hear any sound in my laptop.
    In fact I found some drivers for Realtek controller High definition audio
    but they have nothing did.

    I give the floor to toshiba in Greece and they told me that this laptop is designed only for windows vista!
    Can this be true?
    Help, please

    Hello

    In my eyes, you have misunderstood something. Of course, that the laptop can handle Windows XP and it should work correctly, but as you say the device was shipped with Vista and so the guys at Toshiba support don't provide any support for WinXP on this laptop.

    As far as I know page driver Toshiba also provide drivers for win XP. Therefore, visit European driver of Toshiba page and choose the good laptop-> PSL33 Sat L30-113

    You will find a driver 5.10.0.5273 version XP. This should work!

    Have a nice day ;)

Maybe you are looking for

  • by using a structure of the event to restore a Boolean control with change in value for the menu ring

    I'm trying to get two Boolean buttons to reset when the value of a ring menu.  For this I use a structure of event defined to execute with a ring value change.  However I have another code that should be run while the structure of the event expected

  • I can't for IE8-KB974455 security update install

    I am running Zone Alarm Extreme Security, I am connected to the internet via a 3 G cellular Modem by BandRich. 1. I ran two virus/malware using Zonealarm and Trendmicro audits to check that there is no problem2. I tried to install by closing my compu

  • Reference Dell SC4020

    can someone help me set up my new Dell sc4020. (1) what is the default IP address for the management port (2) what is the management tool to manage the storage of sc4020

  • Reinstall Windows 7 using the same product key on another computer.

    I bought a product key on the Microsoft site, and a few days later I received the disks by mail (a year ago). I now use it on this computer, I plan on building a new computer soon. I'll be able to disable this old computer product key and activate it

  • Error 1935 when installing Acrobat Pro XI

    Hello. I get the following error when trying to install Acrobat Pro XI:Adobe Acrobat Pro XI (11.0.17)Error 1935. An error occurred during the installation of assembly component{9718BF1D-6A9F-3406-A992-630F7EF2F164}HRESULT: 0 X 80070308This happens wi