Satellite L755 - battery falls down when it is turned off

Similar Questions

• Satellite A500-1GL - battery goes down when it is turned off

  Is it normal for the battery to run down, even when the laptop is turned off?

  I had the laptop a month now and notice that when I have a fully charged battery when I turn off, down to almost 90% in 1 day when I turn it on back.
  Its worse still when I leave it a few days.
  Is this normal - I would have expected the battery to keep better workload.

  Hi RICKOSHAY.

  It of a perfectly normal behavior that the battery is run down while the laptop is turned off. For example, I lose 3-4% battery all night.

  10% during the night is a bit too high, so you have to disable in the BIOS options posted by Akuma. I did the same thing on my laptop and it improves the fully charged battery. :)

• Excite the AT - 10 battery goes down when it is turned off

  I have an occasional problem with my excited AT - 10A - 104. Usually when I turn it on, it's nice, but about once in 5, the battery is completely flat. This can be annoying when I need to use somewhere where there is no loading facilities.

  I always if ensure that I have turned it off properly, and it still shows the message 'closure '. Also, I make sure that there are no applications in the list of recent applications before shutting down.

  Can anyone suggest a way to avoid this?

  Have you tried resetting the tablet to the factory settings?
  If this is not the case, try because the problems in the system that may affect the battery working time.

• A satellite - new battery is flat when power off

  Hi all

  I have a new battery that the other was under warranty.

  When I stop and turn off the power to the computer, the battery seems to be running in the back ground as when I turn on the pc there are only about 3 percent of power in the battery.

  What are the correct settings, so I can stop and the battery does not get used?

  Thank you
  Jacquie

  Hey,.

  Really shut down you the computer, or it is in standby mode? No battery power is necessary if you turn off the computer or switch to hibernation mode. Standby battery power is required.

  In addition, you wrote that you have a new battery. How many times you load the already? A new battery must be charged at least 5 times to reach full capacity.

  If you have loaded the battery is battery LED color change?

• Satellite 1800-354 is unable to load the driver when it is turned off during the night

  Hi could sombodu help me to solve this problem.

  My laptop wives is unable to load the driver when its been delivered overnight. It's normal runs when the drivers installed and when it was turned off for about a half hour.
  The laptop has windows xp sp2, the card is a belkin f5d7010 802.11 g and I downloaded the latest drivers for it. Thank you louis.

  Hello

  This driver is the problem for the PCMCIA port or wireless network card?

  Good bye

• How and when the computer turns off automatically?

  Listen to internet radio, Sys Pref > saving energy on the default setting, wake up and radio program cut.

  This is great... .buth how and when the computer turns off?  When I reopen it wifi comes back, I'm correct when she stops she also turns off wifi?

  Hello allan299,

  Thank you for using communities of Apple Support.

  According to your post, I see that you have any questions on how and when your computer shuts down, and how the WiFi on your Mac is affected. I know it's nice to be able to properly manage what happens when your computer stops and starts in mode 'sleep'. I'm happy to help you find the best resolution.

  You're right, when your computer stops completely it will turn the Wi - Fi. If you enable the wake for network access, Wi - Fi remains lit, and you can access shared resources on your computer, such as printers or iTunes shared playlists even when your computer is in "sleep". Definition of a calendar closing and start on your Mac can also be useful.

  Check out the following resources that will help the set options that control the energy use of your computer, sleep, and wake-up times for your Mac and the calendar from your Mac to turn on or turn off or go to sleep:

  OS X Yosemite: energy saver Preferences

  OS X Yosemite: set sleep and wake up on time for your Mac

  OS X Yosemite: A schedule for your Mac to turn on or turn off or go to sleep

  Best regards.

• Toshiba 32RV635D does not power off when the computer turns off

  Hello

  I inherited a Toshiba 32RV635D. I have a PVR based on linux (Mythtv) connected to the TV via HDMI, connected on a Nvidia GT610.

  With my previous TV, a Vistron LCD Panel at low prices, he would go to sleep when the put PC into hibernation and light up when the PC came back.
  This required no configuration of me, he's done right. The Toshiba TV does not work.

  With this Toshiba TV, when the POR turns off the TV turns off screen but is actually still on - power led remains lit in green.

  Same thing with the other way around - if I put the TV in standby and powered the POR, the TV does not respond and I have to manually put out of Eve.

  I updated the firmware and it has not changed anything, and I can't find anything related to power management in the menus of televisions. I even tried just pulling the HDMI cable to the back of the TV so it has no physical active entry, and yet, it does not fall to sleep.

  The Amazon page for TV mentions the power management features, and I expected from what I understand, it should behave the way she.

  I read a lot on HDMI-CEC, but to use it with my existing kit, I would need to buy an adapter USB - CEC, and which seems a little odd because my previous TV not cheap-as-chips just done this...

  Also, the different uses in linux suggests considers its sounds the right - 'xset q' running when the computer is idle tells me that "the monitor is turned off" when in fact it is not.

  Clues?

  Ricklous, it can be useful if you have a look at the url
  http://www.Toshiba-OM.NET/LCD/PDF/English/Country_Specific/RV635-323742-English-specific.PDF

  If you want to download the manual of the English edition for your model, I have not read through, but it may be useful to you.

  Either by the way, I have the model 32RL900A and find only a VCR plugged into the claims of taking SCART screen every time it turns on while the TV is set to a string of FTA (Free To Air) and then 'hands back' screen when he (PVR) goes out, and this, I discovered, is a characteristic of the system SCART.

  I don't know if this information is useful to you, but hope it helps.

  donhe7

• MacBook pro is only supported when it is turned off

  MacBook pro is only supported when it is turned off

  What can I do?

  Have you tried a SMC reset?

  https://support.Apple.com/en-us/HT201295

  What happens when the MBP is on?  How do you know that it is not reloaded?

  Ciao.

• HP 7 more: my tablet based itself when it is turned off

  My tablet factory resets when it is turned off

  See if this helps: 7 HP, HP Slate 7 tablets - find the model number, product number, serial number and the Android OS Version on your HP Tablet (4.1/Jelly Bean Android)

• I was almost finished to fill a very large document when my computer turns off. Is it possible to recover what I had done?

  Original title: Document lost

  I was almost finished to fill a very large document when my computer turns off.  Is it possible to recover what I had done?

  Hello

  What document you worked on?

  Have you worked on all office applications?

  If you are working on a Word document, you can check out the following link and check if that helps.

  http://support.Microsoft.com/kb/316951

• Bluetooth freezes when the screen turns off

  Having a problem with the Bluetooth on my pre. I coupled it with a Plantronics Voyager 855. Initial pairing works very well, but after the screen on the pre turns off, the connection goes bad. When I turn the screen back on, the Bluetooth application on the phone always displays the connected headset, but it is not. If I try to play music, there is no sound, and if a call comes in, I can hear the person on the phone, and not on the helmet.

  About 30-45 seconds after the screen turns off, I hear the high tone of the headset which means that it has lost connection. I don't think that the headset is bad. It worked very well with my previous phone.

  If I have music when the screen turns off, the connection is very good. It's like, when there is no active communication between the phone and the headset, and the screen turns off, the bluetooth on the phone goes into a blocked State. I can restore the connection by turning off bluetooth on the phone and then on again. It reconnects to the helmet, until the next time the screen turns off.

  I tried this to get a better idea of the problem...

  If I remove helmet > disable bluetooth phone > turn on bluetooth on the phone > put the headset in pairing mode, it pairs fine.

  If I remove helmet > disable bluetooth phone > turn on bluetooth on the phone > turn off the screen > wait 45 sec > turn on the screen > put the headset in pairing mode, then it does not.

  Again, it is like turning off the screen causes the bluetooth of the phone hang. Given that the screen turns off fairly quickly, I basically disable bluetooth phone and back on every time I want to use it.

  Any thoughts?

  My problem is solved.  Turns out that I had a defective unit.  He traded last night, and it works fine now.  Got the yellow box this time.  First of all, we had the black cover.

  The swap was a little complicated.  I bought in a store of absolute Wireless in Garner, North Carolina.  It is a reseller of third party.  They did it to a Sprint service center to have a technician "certify" the default before they would replace it by car through the city.  And of course, the service center couldn't do the replacement, so I had to go back through the city to the point of purchase after they certified it.  Best of all, the procedure of "certification" involved explaining the problem to the technician for about a minute, she agreed with me that it was malfunctioned and his writing his employee with the ID on the back of a business card to bring back me to the first shop.  She has not yet turn the phone on itself.  She said pretty much the guy to the absolute Wireless has been a * beep * by sending me to it in the first place b/c, we could just do this by phone.  PITA BREAD.  But I suppose it is, that's what I to do not buy directly from Sprint.

• Help: Fuze distorts the sound when the display turns off

  Hello

  Since a few days, I own my rocket. Today, I recognized the following problem:

  When the display turns off the "rocket" distorts the song. It's a bit like stuttering, it's his bad.

  When I keep the screen turned on (by clicking on the boxes or more) he playes the song of good quality.

  The EQ is set to standard.

  Has anyone experienced the same problem?

  I don't know what to do, what an individual problem of my camera (default?) or maybe a general problem? I would stay there or should I change it?

  Thanks in advance,

  Stefan

  This problem is fixed in the next firmware should be out in the next few days.

  TO work around it, just put the equalizer settings on the equalizer custom for anything other than 0,0,0,0,0

• U2715H - Windows automatically resized when the screen turns off then turn it back on

  • Windows 8.1 Pro
  • 1 single monitor connected to the PC
  • native resolution 2650 x 1440 at 60 Hz the value
  • through CDM of the monitor to the RFP the ti EVGA 750 SC (cable Dell)
  • all drivers updated on 28/12/15

  I just bought this monitor and I noticed this strange behavior. Whenever I have turn off the monitor (or it will turn off by itself), if I didn't have a maximized window, all windows (regardless of size) gets automatically resized to fit in the left upper quadrant when the screen turns back on again.  If I had something full screen, this behavior does not occur.

  I find this very annoying. This behavior happened with my previous monitor, which was only 1080 x 1200.

  I was unable to find any setting for the U2715H disable this "feature". This isn't because EasyArrange from Dell. I do not use this feature. And this always happens with Display Manager not installed.

  Is it just a 'feature' of Dell U2715H? Is responsible for Windows? Help, please.

  TIA

  There was no pilot or changes to the hardware of my first post.  BTW, my monitor is a Rev A02.

  A few days after my previous message, another question emerged.  Monitor flash intermittently ON / OFF every few seconds.  I unplugged/replugged the cable CDM - DP and that seems to fix things... until the next day.  This time, I nothing could fix the random rotation power SWITCH of the monitor.  Desperate, I decided to plug an old HDMI cable, I had to hang out.  Flashing problem has been resolved.  Not only this, using HDMI solved my original problem of auto resizing windows.

  The solution to my original problem: use an HDMI cable.  I went to the Dell CDM - DP cable and the problem has been resolved; no more windows resize automatically when the monitor turns off in sleep/towers.  I always get the native resolution at 60 Hz and there is no noticeable disadvantages to the use of the HDMI versus DP interface.  I've been using the HDMI cable for about a week and there is no other issue.

  Just for additional verification, I bought an Accell UltraAV DP - DP 1.2 cable (B142C-007 b-2), one of the few officially approved by VESA (see link below).  Using this cable does NOT my automatic window resizing problem original.  I do not use it long enough to see if they would prevent the random flashing question.

  I still don't know the exact cause of my original question.  I guess it's a driver problem with DisplayPort standard.  But if you do not need DP 1.2 functionality, I suggest that you just use your GPU HDMI output (if she has a).

  www.DisplayPort.org/.../How-to-Choose-a-DisplayPort-Cable-and-not-get-a-Bad-One

• How to stop the circle of blue on the mouse pointer when the machine turns off

  Regarding Photosmart 5510e printer all in one product No.CQ183B... Model No.B111h... Serial number {content removed}

  Cannot get rid of the attatched blue circle to the pointer of the mouse when the computer is turned off, because it is the noisiest printer that I have ever bought, it even guard the neihgbours awake. Thers seems there have much the same complaint of the HP printer owners concerning the blue circle. Advice please, thank you jh

  Most likely the computer is looking for the printer for features such as Scan computer and alerts the ink. Disable these features should stop the blue circle of projection. Double-click the printer on the desktop icon to open the Printer Wizard. Double-click the ink level chart found at the top of the window. Click the Advanced tab. Under Alerts ink make sure the box "only when I print" is selected, and then click close at the bottom of the window. Double click on manage the Scan of the computer. Click on disable. Close all open windows. This should stop the computer from looking for the printer when it is turned off. Let me know what happens.

• Pre Bluetooth crashes when the screen turns off

  Having a problem with the Bluetooth on my pre. I coupled it with a Plantronics Voyager 855. Initial pairing works very well, but after the screen on the pre turns off, the connection goes bad. When I turn the screen back on, the Bluetooth application on the phone always displays the connected headset, but it is not. If I try to play music, there is no sound, and if a call comes in, I can hear the person on the phone, and not on the helmet.

  About 30-45 seconds after the screen turns off, I hear the high tone of the headset which means that it has lost connection.

  I don't think that the headset is bad. It worked very well with my previous phone.

  If I have music when the screen turns off, the connection is very good.

  It's like, when there is no active communication between the phone and the headset, and the screen turns off, the bluetooth on the phone goes into a blocked State.

  I can restore the connection by turning off bluetooth on the phone and then on again. It reconnects to the helmet, until the next time the screen turns off.

  I tried this to get a better idea of the problem...

  If I remove helmet > disable bluetooth phone > turn on bluetooth on the phone > put the headset in pairing mode, it pairs fine.

  If I remove helmet > disable bluetooth phone > turn on bluetooth on the phone > turn off the screen > wait 45 sec > turn on the screen > put the headset in pairing mode, then it does not. Again, it is like turning off the screen causes the bluetooth of the phone hang.

  Given that the screen turns off fairly quickly, I basically disable bluetooth phone and back on every time I want to use it.

  Any thoughts?

  My problem is solved.  Turns out that I had a defective unit.  He traded last night, and it works fine now.  Got the yellow box this time.  First of all, we had the black cover.

  The swap was a little complicated.  I bought in a store of absolute Wireless in Garner, North Carolina.  It is a reseller of third party.  They did it to a Sprint service center to have a technician "certify" the default before they would replace it by car through the city.  And of course, the service center couldn't do the replacement, so I had to go back through the city to the point of purchase after they certified it.  Best of all, the procedure of "certification" involved explaining the problem to the technician for about a minute, she agreed with me that it was malfunctioned and his writing his employee with the ID on the back of a business card to bring back me to the first shop.  She has not yet turn the phone on itself.  She said pretty much the guy to the absolute Wireless has been a * beep * by sending me to it in the first place b/c, we could just do this by phone.  PITA BREAD.  But I suppose it is, that's what I to do not buy directly from Sprint.