Satellite L850-ideogram - recovery stop error message

Similar Questions

• Satellite L850 - AMD driver stopped responding message

  I received this question now for a few months, and I don't know what to do about this.
  I'm working away and all of a sudden the screen goes black for a few seconds then comes back and receive a message "display driver amd not responding and has successfully recovered" - what happened twice that night within minutes of each other.

  I have installed the version of the driver is that the same as driver of Toshiba download page. I tried to move to the AMD Web site for a pilot, but they offer a tool to find the right driver but the tool is not compatible with Toshiba and said: to do ' Toshiba Web site, how dumb.

  I have a few days ago, I have a facotry "Reinstall" the system to see if that helps, but obviously he didn't. I even tried uninstalling the driver and always put back in place, has not helped.

  So I do not know where to go from here.

  I thought it was a problem with windows 8, the problem started after the upgrade, so I went back to factory default windows 7. But the problem persists.

  Hello

  I think that the problem is related to your driver.
  An update should fix this
  But as you say, you tried to download and install the driver from AMD, but it did not work.

  The point is that you must download and install the drivers manually:
  http://support.AMD.com/us/gpudownload/pages/index.aspx

  There you have to go through step 1 step 5 for the compatible driver package
  The package contains:
  Display driver
  OpenCLDriver
  Catalyst Control Center

  You only need the display driver.
  Now you need to update the driver through the Device Manager:
  Here you must use the advanced option allowing you to take the form of driver files the file that you downloaded.

• Satellite A100 - recovery will not be finished and stop error message occurs

  Satellite A100-S2211TD, OS is Windows XP Home Edition of recovery disk,

  I have updated the BIOS to 2.20 and laptop was working fine. The old installation of Windows factory has worked well.
  After a few weeks, I tried to use the recovery disk to remove the noise from the HARD drive.
  The recovery of disk task completed and the computer restarted.
  I got the stop error message
  STOP: 0x0000007B (0xFA335528, 0xC0000034, 0x00000000, 0x00000000)
  I removed the memory that I have entered over the past two years and return the PC in the factory scene.
  However, recovery will not be finished (he worked to restore).

  I am able to boot in dos with a separate boot disk (Dr. back, windows does not start, not even in the safe control mode) and I did chdsk of the disc and disc is fine.

  I've never used before recovery disc, the only thing different is BIOS 2.20 instead of 1.50.
  WEB of TOSHIBA said that if you upgrade the BIOS most 2.00 you can not return to 1. XX

  Thank you
  g

  Hello

  The A100-S2211TD doesn t support the Intel Chipset!
  This laptop was equipped with the ATI graphics card and the graphics driver on the Toshiba page contains us the graphics driver and chipset driver!

  Have you received 100% good recovery CD?

  In your case I would try to install Win XP from the Microsoft CD to check if the same error would appear if no drivers are included in the CD of the OS.

  Check it out

• Satellite L850 - webcam suddenly stopped working

  The web cam on my Satellite L850 has suddenly stopped working.

  It does not appear in Device Manager;
  I downloaded the latest driver on the Toshiba site;
  I checked the BIOS and the web cam is turned on;
  Always when I open the web cam application I get the following message:

  "webcam initialization failed Please restart request and camera control.

  I scoured the advice forum and short of a return to the top and reboot disk HARD, I find no reasonable answer. I can't back up as I am away from home is out of the question. I need web conference call cam / call my family to the United Kingdom back.

  Tired of going round in circles and getting nowhere.

  Any suggestions?

  Post edited by: mrclean

  Even if you have not changed the settings in the BIOS, you must Access the BIOS to make sure that the webcam is turned on it!

  I also recommend the suite of this workaround:
  Uninstall the webcam software
  Uninstall the VAP
  Uninstall all software needed the webcam (Skype, etc...)
  Now, restart and install CCLeaner (cleaning of freeware software)
  Reboot once more.
  Run CCleaner and clean the system and the registry.
  Reset
  Now follow with installation of VAP
  Reset
  Install the webcam software
  Reset
  Test webcam.

  Good luck

• Black cartridge HP PSC 950XI all-in-One HP 78XL mark stop error messages.

  Black cartridge HP PSC 950XI All - In - One HP 78XL mark stop error messages "" error: installed incorrect color cartridge ";" "" Install the color cartridge"and"install the color cartridge. I cleaned the contacts on the printer and cartridge and printhead. Cannot make it work.

  I've tried everything and still get error messages that continue to change so I can say that things are get cleaned but this cartridge is just not good. I ordered more than HP 78 and 78XL cartridge. If they show mistakes I'll let you know. Thanks for the suggestions, there was one that I had not tried before so I will certainly remember.

• I put the machine into hibernation and when I restarted, I got a blue screen with stop: 0 x 00000024. Restart gave a different stop error message: 0 x 00000050.

  Original title: Blue screen problems - Stop 0 x 24 and 0 x 50

  I'm not being updated hardware or software on my Dell Latitude D8380.

  I ran the Windows tool to check if the laptop is suitable for upgrading to Windows 7, but did not install any software.

  I put the machine into hibernation and when I restarted, I got a blue screen with stop: 0 x 00000024 (0x001902fe, oxba4f7948, 0xba4f7644, 0xb9d31ae8) ntfs.sys address b9d31ae8 base at bpcef000, datestamp h8025be5.

  Restart gave a different stop error message: 0 x 00000050(0xffffffff,0x00000000,0xba1bef42,0x00000000) i8042prt.sys address ba1bef42 base at ba1b8000, date stamp 48025c 67.

  Please can you help. Thank you, Sue Dixon

  Hello

  Step 1: Check if you are able to boot in safe mode. If you are able to boot into safe mode, and then try to perform the clean boot to safe mode and check.

  From your computer by using a minimal set of drivers and startup programs so that you can determine if a background program is interfering with your game or program. This type of boot is known as a "clean boot".

  Reference:

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  1. click on start and then click Run.
  2. type msconfig and click OK.

  The System Configuration Utility dialog box appears.

  3. click on the tab general, click Normal Startup - load all services and device drivers and then click OK.
  4. When prompted, click on restart to restart the computer.

  Step 2: Run the check disk hard disk command. (You will be able to try this step if you are able to start in safe mode or in normal mode with success)

  How to perform disk error checking in Windows XP

  http://support.Microsoft.com/kb/315265

  Let us know the status of the issue.

• HP Pavilion a6745f stop error message

  Hello again!

  I'm new to the forum.  I've known a stop error message regarding hpqgpc01.exe.  He says that the program is unable to put end to, click to complete.  I recently bought an HP F4440 AIO.  I tried a solution of a post here. but it did not work.  Anyone has had or has this problem that can point me in the right direction to eliminate this problem?  Anyone know what this file is, exactlly?  AIO has to work properly?  I read a lot of articles and messages about problems with the work of the AIO with Vista.  I really like the IOA and it meets my needs very well, but I can't bear this message popping up every time I shut down my machine!  Any help would be greatly appreciated!  I am running Windows Vista Home Premium with Windows Media Center with Vista Service Pack 1 (64-bit), Athlon X 2 (B) 5050e 2.6 GHz (45W).

  Nice day!  Sorry for not responding sooner, but I just wanted to make sure that your solution worked for me.  And he did.  And I really, really appreciate you taking the time to answer.  Although, I think I found a solution, which, allows all functions to be used without the message annoying "shutdown" appearing.  In a previous post by J. Rhoades(posted 3/28/08) and it reads as follows:

  I got this info from a technician of the HP technical support:

  Go to start > run > services.msc

  Find 'HP CUE DeviceDiscovery Service', change the startup type to disabled, and then stop the service

  I must tell you, it worked like a charm... So far!  But, if he comes back, I'll be sure to post if/when this happens!  Thanks again loads!

  For the record, my questions to HP about this case was void avenue.  I made the mistake in using the Chat, in which you ask someone, I suppose, is in another country and it takes for always answering your questions and they seem to be not very well paid on questions about HP products.  So, I am very grateful, there are people who are willing to share their knowledge and experiences with others.  Looks like we have to depend on 'other '!  Thank you all!

• Received error BSOD, ran Diagnostics, got the error code 2000-0146, tried to boot from different HARD drive, got the same stop error message

  So my friend gave me his computer dell laptop. The thing would boot normally for a few days until he would give me a blue screen of death with the "UNMOUNTABLE_BOOT_VOLUME" message constantly to not even upward. I ran the diagnostics and got the error code 2000-0146. What I've read, this code error means that the HARD drive is bad and must be replaced. So, to make sure that it's the hard drive, tried to boot from an old hard drive, I got around the installation by USB and windows gave me the same stop error message. May - so that means it's a motherboard problem?

  No, it isn't - unless the operating system was installed on this drive AND the system in question, that it won't work as a bootable drive.

  Unplug the system, remove or disconnect the battery and hold the power for 30 seconds approximately.  Turn on and re-run the diagnostic tests - if the same error appears again, the drive is bad.  Replace it.

• Satellite 1900 shows a recovery on error message after reboot after

  My laptop Satellite 1900 305 after recovery uility, when commissioning for the first time shows an error message that indicates that the system has recovered from a serious error of a device. Can someone help me with this?

  Hello

  Well, it would be nice to have more information about your system. What operating system are you running currently installed Bios?

  This message appears again after a reboot?

  Good bye

• Satellite A30: system32\config\system error message

  Hello

  I have a Satellite A30 and when I start it it displays the system32\config\system error message

  He also says I can try to repair it by starting the original windows using the installation CD installation program.

  Problem is that I don't have any CD or recovery discs that I bought the laptop on ebay 2 years ago

  While the options of do I have that I don't really want to spend the money, put it in repair... the credit crunch and all that!

  Thank you

  Hello

  Hmm I doubt that you can solve this problem without going through any system windows disk or recovery disk.
  It seems that the installed OS is messed up and you last chance would be a new installation of the OS on the MS Windows CD or Toshiba recovery disc.

  Good bye

• Satellite M500 - Missing TosHdpAPI.dll error message

  I recently installed Quicken 2011 and after installation, an error message appeared when the laptop starts:
  Cannot start the application... Missing ToshdpAPI.dll.

  I'm running Windows 7 Pro on a Satellite M500

  I have here a way to get a new copy of this dll?

  Hello

  I searched a bit using Google and it seems that TosHdpAPI.dll belongs to Toshiba Bluetooth software stack but he s strange why it is important for your Quicken program

  In your case I would try to reinstall the Bluetooth software which can be downloaded here:
  http://APS2.toshiba-tro.de/Bluetooth/

  If it doesn t help you should contact the manufacture of the Quicken program. Usually, they should know how you can get rid of this error message. They probably have a patch (update) for this problem.

• Satellite C650-17Z - only PXE error message no boot device

  Hi people I was wondering if anyone of you kind people out there could help me. I have a Satellite C650-17Z model and when turn on is the message I get:

  + Intel UNDI, PXE - 2.0 (builkd 083) +.
  + Copyright (C) 1977-2000: Intel Corporation.

  + For Atheros PCIE Ethernet Controller v2.0.1.9(12/15/09) +.

  + Check the cable connection! +
  + PXE - MOF: exit Intel PXE ROM. +.
  + No boot device - insert boot disk and press any key.

  Can anyone any sense of the message above?

  Hey Buddy,

  This error message means that an incorrect boot order is set and the computer tries to start between LAN port to the internal HARD disk space. It should therefore go into BIOS setup and change the boot order. Put the HARD drive as the first boot device internal.

  Take a look at this article from Toshiba:
  [PXE error message appears during the clean boot procedure | http://forums.computers.toshiba-europe.com/forums/ann.jspa?annID=8]

• Satellite 5200 903: cooling problem error message

  a few minutes after the start of my Satellite 5200 903 (xp home sp1) an error message apears: "problem with the cooling system, shut down your system and send it to the service ' (this is a free translation of the German..) I installed a temperature control tool, the software displays the temperature of the processor about 60 ° C, but I don't hear the fan...
  Can anyone help?

  Hello

  You have a good chance that it is only a cooling module.
  This warning message usually appears because the CPU cooling module can cool the CPU properly or it does not.
  However, the best way is to contact the Toshiba service partner in your country. Ask the guys notice and I am sure that you will get an appropriate response.

  Good luck

• Vista Stop error message: 0XC012001D after the installation of Windows updates.

  Original title: vista stop working

  Hello

  I need help on vista, because I update and restart and stop working and appear this error code:

  !! 0xc012001d! Registry\Machine\Components\DriverData...

  Hello

   

  
  1. remember the number of the update you have installed?
  2. could you give us the exact error message?
  3. Once you get this error message? Are you able to boot to the desktop?

   

  Method 1.
  Please check if you face the same problem when recording in safe mode. It is a possibility that one of the non-Microsoft application or driver is causing this issue. Start in safe mode and make sure that us. If you are able to start properly in safe mode, we can perform a clean boot in order to find the root cause.
   
  Step A.
  a. restart your computer.
  b. when the computer starts, you will see your computer hardware are listed. When you see this information tap the F8 on your keyboard key repeatedly until you are presented with the screen Windows Vista Advanced Boot Options.
  c. using the arrow keys, select the desired option of Mode without failure.
  d. press the Enter key on your keyboard to start in safe mode of Windows Vista.
  e. when Windows starts, you will be at a typical logon screen. Connect to your computer and the Windows Vista goes into safe mode.
  f. do whatever tasks you need and when you are done, reboot to return to normal mode.
   
  Step B.
  If it works fine in safe mode try performing a clean boot in order to find the cause root.
  See the article below for instructions on how to start your computer in a clean boot state.
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135
  Note: When the diagnosis is complete do not forget to reset the computer to a normal startup. Follow step 7 in the above article.
   

   

  Method 2.
  Best thing you can do is to perform a system restore just before where the problem occurred.
  I have listed a few articles that explain the system restore in Windows 7.
  System Restore: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions

  
  System restore
  http://Windows.Microsoft.com/en-us/Windows7/products/features/system-restore

  Thus, the article above is applicable to Windows Vista.

   

   

  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• I get the following when starting my laptop Dell - stop error message: 0x000000ED (0 x 84308900, 0 x 00000000, 0XC000009C, 0x00000000)

  Hello

  Since last night I get the above error message on my computer at startup.

  I can not start in any other mode and tried to use the recovery console (starting on the DVD) using FIXBOOT and CHKDSK /R but still no luck.

  I also tried searching on the error code with no luck.  I recently bought an IPOD but was already using itunes and the computer worked very well after the IPOD synchronization.

  I'm stuck and would be grateful if someone could help me solve this problem.

  THX,

  Eliot

  It is proably a record broken. Restart your computer and press F8 when Windows starts to load. Select the last known configuration of God in the menu, then press OK. I had the same problem, and that it resolves. Maybe a program to train register is broken.

  ---------------------------------------------------------------------------------------------------------------------------------
  If the answer can help, mark it as "useful". He he has solved the problem, mark it as 'reply '!
  Andy