Satellite P10 - 554 nvidia geforce fx go5600 update driver

Similar Questions

• BIOS update allows the use of modules of 2 GB RAM DDR on Satellite P10 554?

  Hello

  I have a satellite p10 554 and want upgrad my RAM.
  By default, the maximum that you can install's two Kits of GB 1.
  Are there any - update Bios, that allows 2 GB kits?
  Thank you very much!

  Ron

  Hello Ron

  The same situation with my P20! Unfortunately there is no BIOS update allows the use of the RAM more.

• Satellite P10 554 Display driver

  I use my laptop to produce movies from privat with a program called Studio of Pinnacle. Until Version 9 it worked well. Now on the latest version 10 inside monitor see the didn t movies of my camera. When you start the program, I get a note that the display driver NVIDIA GEforce FX Go5600 must be updated. The Toshiba 4.4.8.5 driver version is installed.
  Is there a higher update available and where I can download this?

  Concerning
  Hansjurgen

  Hello

  Sorry, but Toshiba does not provide a new display driver for the P10. But you can look for a more recent laptop with the same graphics card, maybe he has a newer driver that will work in the P10. Or you can use the driver from the nVidia website, but be careful, it is not designed for laptops and can cause overheating.

  Good bye

• Satellite P10 - 554 dvd - ram does not work

  I got a Satellite P10 554, and as I said above the RAM does not work.
  It should be a software problem, because if I reinstall the drivers it works a few minutes (it did until now yesterday it stopped completely)
  It is impossible to install the new drivers or update a firmware somehow
  (pilot: after rebooting, the old drivers are loaded again (but I uninstalled them))
  (firmware update: I still got the message: invalid drive to update f/w)

  I hope that someone of you can help me ;)

  Hello

  What did you mean with the work of t car doesn?
  You are not able to burn or read the media?

  The error message says it all. I think you re not able to update the firmware because the firmware is not supported on this drive.

  Try to remove the drive from Device Manager, and then shut down the laptop.
  Usually after restarting again the operating system should recognize the drive again.
  If this does not help, you can try to remove the drive from the laptop. Turn on the unit, then go into windows. The reader should disappear. Then stop and reset the drive in the notebook. After this procedure the laptop must load the firmware again.

  It will be useful.

• Satellite P10 554 LAN wireless connection

  Hello people,

  I have a laptop Satellite P10 554. I'm not able to get the wireless LAN. I have a Netgear wireless modem and a Netgear USB wireless "receiver". I have configured the entire setup and switched 'on' switch wireless on the left side of the laptop. Nothing happened. The light on the left side on the laptop that shows the availability of the wireless network never radiated.

  I have installed and inserted into the mobile network.

  Please advise on how should I proceed to get the wireless LAN working.

  Thank you in advance.
  Matel

  Hello

  As far as I know that the Wireless LAN is optional on this unit. This means that the appliance has been delivered without wireless card, but it s can put the card in the laptop.
  Are you sure that your device has a wireless card? You can check in the Device Manager. In addition, must be on the wireless network by using the switch on the side of the laptop and the key combination FN + F8.

  Please check these options.

  Good bye

• Windows 7 on Satellite P10 554, need drivers

  Hello
  I installed a new Windows 7 on my Satellite P10 554.
  Now I can not find some drivers for my device, in particular for the USB device,
  who stands out, if I use an external hard drive.
  In addition, I got an error code 28 for the base systemdevice (to 2 PCI bus) and
  the performances of "Windows 7 Upgrade Advisor', who is not the driver ACPI/CMP0101
  compatible with W7.
  What else can I do?

  Thanks for the reply

  Hallo Lupi

  I had Satellite P10 for the year 2003. So please don't get me wrong, but you have 6 years book, designed for Windows XP Home edition and now you ask you cannot find drivers for Win7.

  What you can do? Nothing. This oldie is not supported for Win7.
  Use the operating system that is supported and to be happy. If you want to use a more recent software I think it's time for the most recent material. ;)

  Satellite P10 is also really nice and absolutely reliable laptop.

• Satellite P10 554 stops after a few minutes and I can not restart

  Hello
  I hope someone can help me with my satellite P10 554
  When I start the laptop, everything is working fine a few minutes. the monitor turns black and the books suddenly stops. I can't restart, when I push the Start button, nothing happens.

  I have to wait about an hour and then I the starts again, but it works for a few minutes and stops again!

  Help me please, cause I need my phone to work!

  Hello

  From your description, I think your device overheat and go down because he cannot be cooled properly. P 10 satellite is older and it's time to clean up. You can't imagine how much dust inside the unit you will find.

  I put t know how are you familiar with this, but if you have no experience don t do it alone.

• Satellite P10 554 does not start

  Hello!

  First of all, sorry for my bad English

  The problem:

  I installed windows XP Professional on my Satellite P10 554.
  I bought it on ebay and the seller said that everything goes well with this laptop and the tests when I turn on the laptop saying the same thing.

  But after installing XP, it does not start!
  It is the boot screen with the blue line that moves. This line moves a little, that it stop and that all the time and nothing happens!
  I tried the same thing with XP home, and windows 2000, but it has the same problem!
  I really need this phone. I hope someone can help me!

  Christian

  > I bought it on eBay and the seller said that if everything goes well with this laptop and the tests when I turn on the laptop saying the same thing.

  You said that the test says it of ok. How did you test it?

  > It's the boot screen with the blue line that moves.

  You mean the OS bar which moves while loads the OS. Am I wrong?
  Hmm, if you have tested the laptop with Win XP and W2K then I guess that you have installed the two OS on this laptop and it was possible to install it?
  Am I wrong?

  Sorry to say but if the laptop is unable to load the operating system the hardware would be a malfunction.
  I think you should first check the memory modules, then the HARD drive. Maybe one of the modules does not work correctly or some bad sectors can cause the problem.

• Problem update satellite P10 554 to XP Pro

  Hello

  got the P10 554, with Windows XP Home Edition. Since I have my own copy of XP Pro and need additional components, which are NOT part of the home ed., I tried to update.

  Works fine until the point where it says "Starting Windows". The progress bar runs out, the screen goes black and not more disk access hard and CD.

  Everyone runs into that as well, or is there a solution for this problem?

  Thanks in advance,
  Jürgen

  Hi, tried to run Windows in Mode safe?

  Good bye

• Satellite X 200-NVIDIA GeForce 8700 M GT SLI 512 MB is defective

  I need help. My laptop died on me. Toshiba Statellite/Satego X 200 series

  When I try and start the Power lights the light hard drive lights up for a milli second and then gooes on DVD light is on but I can't open the DVD player, you don't hear fan works, it makes no difference if Itry and start it with battery or remove the battery and use the power cable the screen remains black. I tried a reboot (I took the battrie and pressed the start butten for 1 min) still nothing.

  I finally took a mock store think (reason why I am I pay?) it could be the graphics card (costs about 300.00 Euros) or motherboard or?
  NVIDIA GeForce 8700 M GT SLI 512 MB which is in a /satego x 200 at Satellite - it someone know where it is in the laptop?

  I can at
  It into the broad back or I have to disassemble the computer laptop everything.
  Thx for any help
  Geordie58

  Hello

  Yes, it could be a graphics card problem.
  In this case the whole motherboard must be replaced.
  And you are right; new motherboards are expensive laptop parts a new cost about 300Euros
  Until it tell s your personal decision, you may get a second hand Internet goo mobo

• Satellite P100-109 nvidia geforce 7600go

  I'm looking for a spare part for my satellite P100-109.
  Is it possible to buy Toshiba parts? More specific to the graphics card

  type: NVIDIA® GeForce Go 7600
  256 MB DDR2 video RAM
  16 x PCI Express

  It is easy for me to replace the card myself.
  The rest of the laptop still works fine enough to last a year or two.

  Thanks in advance

  You can buy some hardware components separate by some independent online, or perhaps on eBay stores.
  As far as I know Toshiba doesn't offer these parts.

  So use Google and try to find out if you can order a card as part separately.

  You have experience with this sort of thing? I mean can you do it alone?

• Satellite P100-221 NVIDIA GeForce Go 7900 TV-Out problem

  Hi, I have Toshiba Satellite P100-221, with NVIDIA GeForce Go 7900 GS, it has a tv (S-video) output, I had cable & connected & nothing appears on television, & when I go to advanced settings & see the video card options, I found that nothing related to the modification of the display to the TV or anything...
  When I looked in the manual, I found all the explanation based on NVIDIA GeForce Go 7500 :(
  I also tried Fn + F5 & choose the TV also, nothing happens, knowing also that the cable I got one side S-video, & the other side completely normal video in cable
  Help, please
  & thx a lot

  Post edited by: gak_7

  Hello

  First, you must connect the laptop with Palm of TV s-video cable. Then, go to the TV with the FN + F5 key combination. Select TV and LCD.
  Then you must enable the feature s-video on the TV (consult the manual of your TV). Without activating the s-video on the TV, you will not be able to see something.
  This should work on NVIDIA GeForce Go 7500 and 7900!

• Update problem NVidia GeForce GT 230 M driver

  I have a HP Pavilion dv8 with an Intel Core i7, Windows 7 64 - bit and NVidia GeForce GT 230 M video card.  He is currently leading a pilot dated 05/02/2010, version 8.16.11.8906 (the same version of the driver from the list of updates of HP drivers for this PC).

  Updates Windows 7 pushes a NVidia driver updated, dated 16/10/2010, version 8.17.12.6099.  If I let the update, the PC will not get past the 'Welcome' of Windows screen on startup and will make a noise when on this screen that is normally not.  The only way I can get past this problem is to restart the PC in safe mode and do back this driver or use to go back to a restore point before this driver update.  I made sure that I reduced the potential causes of this problem starting only update the video driver.

  What's wrong?  What I would do to that will make this updated video driver to work on my PC?

  The problem I had with the pilot who started this topic has been resolved.  I was advised to load the latest driver from nVidia directly, which is the version of the 8.17.12.6658 pilot, dated Date 07/01/2011.  I tried this driver and it worked well.  I don't get everything grows Microsoft or HP to update the video driver, so I'm a happy camper now.

• 6TO4 ADAPT NETWORK ADAPTER DOESN'T WORK DOES NOT CORRECTLY AND MY DRIVER NVIDIA GEFORCE 7600 COULDNT UPDATE.

  MY LAPTOP PROBLEMS AS SPEED TO MARKET AND TOO SLOW, I'M LEFT TO CHECK THE DIAGNOSTIC TOOLS.IT PROUNE PERFORMANCE FOR ME THAT MY 6TO4 ADAPT IS NOT WORKING AS WELL AS MY PILOT TO UPDATE NVIDIA GEFORCE 7600 COULD NOT... URGENT... I THANK YOUR OBTAINED IF NO SOLUTION... A lot..

  1. you can update your graphics here driver (just answering questions). Download the appropriate file, run it, follow the instructions on the screen, reboot when you are prompted. Check to see if that helps with performance.
  2. http://windows.microsoft.com/en-US/windows-vista/Optimize-Windows-Vista-for-better-performance

• Problem with NVidia GeForce 650GTX installation/update of drivers

  I bought a VR Deepoon E2 helmet last week. Installed according to the instructions. Home screen don't watch in headset for installation appears to succeed. Tried to use it with the Steam VR DCS World Flight Sim game (which he has been quoted as being able to do), but nothing in the helmet. Disconnected leaves VR on PC and Steam steam. Headset is back to a blue room screen smoky (immersion 3D yet) with a message to reset the headset by pressing the A button on the device to hand.  While software Deepoon software Oculus Rift DK2, he was of course, using the Deepoon E2-based does not come with the hand units as the Rift of Oculus, so I could not use any button.

  Active Web. Uninstalled and reinstalled as recommended (possibly 5 times). Always comes down on a blue color screen with the Message "A switch". Web checked and found Deepoon Assistant Software. This allowed me to spend DK1 DK2 and Deepoon, but any helmet showed was now a big Red Letter D on a gray background.

  Checked the web once again, and he says that the only way was to uninstall a remove all traces of the Oculus and Deepoon from my PC, including my registry. I did it with great care, but think I may have missed and remove some registry keys which makes reference to my NVidia GeForce graphics card 650 GTX which could have are embedded in the Oculus/Deepoon records.  Now given up trying to get this working VR helmet (he had other problems as well as glitch shaped growing on the right lens and not perfectly update) and I'll send the item back for a full refund on EBay.

  Having provided the measures so far, my current status is now worse.  I can't use my graphics card. In Device Manager, it shows an exclamation point, and the games that worked before will not now due to the "lack of DX11 compatible hardware. I tried the update drivers and then downloading the driver from Nvidia for my graphics card, and in both cases, the drivers will not install because there is no recognized the installed card. I tried uninstalling the driver and graphic card and then search for the new hardware in Device Manager. He finds that the GTX 650 but used to always install the driver concerned. I even thought of removing the card graphic, commissioning, remove all references from Nvidia in the registry, close, put my card back in and go upward as if it were to find the map for the first time, but I'm now concerned I will be myself deeper bury.

  If someone could help me please with what I'm doing now, because I'm at a loss and without my games I'm even more depressed. I am running out of ideas and short to the shop that will probably charge me a fortune for a simple registry repair my computer, I don't know what else to do. I have a last file 'dxdiag' that if someone can help I can send it in by e-mail if you need for further investigation. It's my last option.

  Hello

  To get a better idea of your request, please provide us with the following information:

  • The version of the driver installed
  • The version of the driver you want to install
  • Device status (provide a screenshot)

  I'll keep an eye out for your answer