License of VCS & MSDS

Similar Questions

• Client Jabber Viceo registry for VCS/MSDS

  Hello

  I am trying to record a video jabber VCS or TMS customer but his does not work. Whenever I was

  "Bad username, domain and/or password". Check spelling and caps lock.

  Do not know why. Should what I do to register a customer with username and password? VCSC and VCSe are configured for access from inside and outside VCSe.

  Is there a guide for video Jabber clients?

  Best regards

  Jason

  Hi Jason!

  You need a starter pack of VCS-highway or TMS (license + Movi licenses) and a VCS (with the option of commissioning key device).

  As you write VCSe and c its more likely that you do not have the starter pack.

  She has need of configuration and user creation, so it would work not just out of the box.

  The recommended method is the TMSPE, you will find here the deployment guide:

  http://www.Cisco.com/en/us/docs/Telepresence/infrastructure/tmspe/Install_Guide/Cisco_TMSPE_Deployment_Guide_1-0.PDF

  If you have older versions of TMS/VCS you will use it (but I recommend you upgrade and use TMSPE!):

  http://www.Cisco.com/en/us/docs/Telepresence/infrastructure/TMS/config_guide/Cisco_TMS_Provisioning_Deployment_Guide_13-0.PDF

  In addition to this documentation Cisco for TMS, VCS and JabberVideo control.

  TMS:

  http://www.Cisco.com/en/us/products/ps11338/tsd_products_support_series_home.html

  VCS:

  http://www.Cisco.com/en/us/products/ps11337/tsd_products_support_series_home.html

  JabberVideo:

  http://www.Cisco.com/en/us/products/ps11328/tsd_products_support_series_home.html

  Jason: Please note the validations and define the thread if it's an answer!

• VCS & MSDS requirement

  Dear team,

  Is it possible to configure VCS with VCS and TMS highway with customer movie without domain name?

  Concerning

  Nikhil

  No, a domain component must be Movi uses SIP and SIP.

• Failed to load license in VCS to MOVI

  Hi team,

  We cannot load the Option key to MOVI in our VCS server key. We get the message error "failure to add Option key Option key not valid."

  The Code of the room that we had ordered is LIC-MOVI-25.

  regds,

  Aman

  Yes that's right, THAT TMS is required for the provision of the Movi/Jabber video in addition to the VCS, unless you use a VCS Starter Pack (in which you should not have bought the option LIC-MOVI-25 in all cases).

  -Andreas

• Telepresence - who ensure license on telepresence in VCS

  Hi guys,.

  I need to check the license of telepresence equipment reference in VCS, but I Don t have any experience on the VCS. That I can check this license on VCS. I know that models telepresence recording in CUCM and anothers in VCS.

  Thank you

  Wilson

  When you connect in the VCS, you can check the status on the landing page to see the use of the license. To see more specifically what licenses are installed, click the Maintenance > Options keys.

• How to pass the vcs - e License? A server to Server B.

  Hello

  my company has a vcs test server.  and we buy the new server.

  I need to spend vcs again server.   I backup and deploy using the vmware ovf file.

  deploy the success. but new server vcs poster license error.

  How to pass the license of vcs?

  Of his assignment, it is not necessary to use both servers at the same time.

  If I see, if you move the virtual computer between two servers and you used local storage the

  Serial number will change...

  Please remember useful frequency responses and identify useful or correct answers.

• VCS HW license VM migration

  We recently bought 4 x LIC-VVCS-E-M-PAK and 4 x LIC-VVCS-C-M-PAK so that we can migrate all our calls licenses from VCS HW devices to virtual machines, but when I go to buy one of the PAKs I got for the VCS - C, is that display the following information available:

  		LIC-VVCS-C-M-PAK	1
  		LIC-VCSE-100	1
  		LIC-VCS-GW	1

  Shouldn't it allows me to enter the serial number of a device from HW to migrate, then give me licenses relevant call too?  Has anyone else had experience migration licenses HW to VM that might help us with that?

  Hello Nick.

  Please mention the discussion below, you will need to send a certain group with Cisco to process the query to rehost the option unit to the virtual computer buttons.  I am sad to say that it is not no matter how automatic background process that does this when you buy a migration for any product, it is all the manuals and done by the client most of the time.

  vcsvcse-license-migration-material-vm

• Option provisioning VCS key

  I got 13.2 TMS, VCS - C 7.1, VCS-E 7.1

  100 MSDS supply of licenses,

  VCS - C has the following license:

  0 calls no route, route 100 calls, 2500 records, encryption, interoperability, FindMe, Interfaces network double.

  VCS - E has the following license:

  40 calls no course, 10 calls from crossing, 2500 records, 1800 TURN Expressway, encryption, interoperability, FindMe, relay, Network Interfaces double

  In order to get video Movi/jabber to work, are these sufficient or do I have the device key on the VCS - C supply?

  I have implemented the TMS in legacy mode, agent and managed to sign up customers movi and make and receive calls from clients ipad and laptop. I have now migrated the TMS TMSPE and customers will not fit. Not sure if the license key is the reason why.

  Help, please...

  Hi Yusuf

  I sent you a private message.

  / Magnus

• VCS Clustering

  Hello

  We have a cisco Call manager/IM & P 10.5 version installed on two BE7K chasiss running in PUB/SUB.

  My query is on the redundancy of VCS. We must deploy VCS Expressway Core and Edge version 8.x on same UCS platforms.

  My first request is can we install VCS Expressway Core and Edge in redundant mode, as well as in the case where if a UCS chassis fails, the other UCS chassis can handle the traffic?

  If so, claims we separate licenses when VCS Expressway Core and Edge is installed in redundant mode?

  Please notify.

  regds,

  Aman

  Having a configuration redundant expressway is no problem. They are designed to be clustered.

  run you a set-ch. & EI in a cluster on each of your BE7k configuration and it works for redundancy. Check out the guides below on how to set up a cluster and what else to care

  of (such as SRV records)

  Also licensing should be easy. And Yes, you need additional keys, based on the series

  number of additional deployed highways.

  You just need to get a set of additional keys for the new pair of expressways which should

  be 0 products$.

  Further, I recommend to take a deeper look in the Cisco documentation:

  http://www.Cisco.com/c/en/us/support/unified-communications/Expressway-s...

  http://www.Cisco.com/c/en/us/support/unified-communications/Expressway-s...

• Question of the use of non-traversal license

  Hello world! Wanted to ask a quick question. If endpoint makes a call to another endpoint (via WAN) and each of them is registered in VCS on their sides and then if it will use the non-traversal license of VCS or just one of them?

  Thank you

  Each call and the end point that enter or exit the VCs will have 1 license appeal.  What determines the type of license, either Non-traversal or crossing is less (confirmed by the help guide).

  Calls of traversal VCS: VCS standard video or audio calls, including business-to-business calls, B2BUA calls (for encryption of the media or ice) and interoperability or sent through gateway calls to third-party solutions where the VCS as well takes the call signaling and media of the call. Each call consumes a license of traversal appeal.

  VCS non-traversal calls: here's the VCS standard video or audio calls where the traffic goes through VCS, but the media passes directly between the endpoints, or between an endpoint and another system in the direction of the call. Each call consumes a license non-traversal call. Note that Lync B2BUA calls are classified as non-traversal is called (even if media cross the VCS).

• VCS Configuration Start

  Hello

  I'm starting a VCS application to our office Installer.

  Got VCS X7.1 MCU 4505 4.3 (1.68) & CUCM 8.6.2

  First, I had 2 x MX300 and 1 unit of x MX200.

  on th eend CUCM points work very well as 2way. How to check that I have enough licenses for VCS and MCU start configuration. as the insight VCS gives the following result. Like all the configuration is on LAN/WAN not involved any firewall should I these licenses?

  Call non-traversal licenses	Current	0
  	PIC	0
  	Since the last restart	0
  	License limit	0

  ? mediaRouted = true "> call traveled licenses"Current 0 PIC 0 Since the last restart 0 License limit 0 Licenses for registration Current 1 PIC 1 Since the last restart 2 License limit 2500

  The VCS - C should come with 10 non-traversal and 100 licenses of course, unless things have changed since we bought our...

  You will need both; non-traversal for h323<-->h.323 or sip<--->sip calls within the Organization and interworking sip and IPv4<--->IPv6<--->h323 crossing licenses called the organization.

  /Jens

• VCS licenses on BE6000

  We have the Cisco C220 with BE6000. In particular, these are elements CTI-VCSC-BE6K-PAK, LIC-VCS-10 +, LIC-VCS-BASE, LIC-VCS-GW, LIC-VCSE-5 + in our price list.

  Is it enough to install the control of video Communication on a VM Server?

  After installing VCS on VM, trying to save PAK has to fail with the message:

  "Sign up for virtual PAK Base SW, before registration Option PAK".

  Documentation [Cisco VCS on Machine virtual Installation Guide (X8.1)]: follow the on-screen instructions to register your PAK software (with a prefix part of the LIC-SW-VMVCS number)...

  But I do not see the LIC-SW-VMVCS in our price list. Can we use given above?

  Whenever we bought our VM VCS and conductor (because he was so VM), I sent the information to [email protected] / * /.  Note Oleksandr, you misspelled email, put a w instead of v at the beginning.

  I have provided the following information:

  Name, Email, phone number

  Sales order number

  Product reference number

  Serial number

  Once you send them the serial numbers, you should receive the unlocking keys, if not already.  Then shortly after, PAK keys to submit online at

  https://cisco.com/go/license/, to recover the keys to the option.

• License VCS\VCSE of virtual machine hardware migration.

  Hi all

  I want to migrate my hardware to virtual VCS\VCSE.

  Both servers are covered by the active maintenance contract.

  How licenses work in this case? What is the procedure of transfer?

  Any cost?

  Thank you.

  Hello

  About Cisco VCS, you want to migrate virtual machine hardware, you will need to purchase a new license to make the transfer. These are the partnumbers you need:

  R-VMVCS-C-M-K9

  HW migration to E - Delivery Virtual VCS only controls

  R-VMVCS-E-M-K9

  HW migration to E - Delivery Virtual VCS Highway only

  Please contact your Cisco representative for more information.

  After purchasing the license, the license of the VM device rehost will be made by a specific Cisco team, not the team of global license, it is a process different rehost. You will need to send your request to [email protected] / * /, this team will provide instructions to rehost your VCS license correctly.

  I hope this helps.

  Concerning

  Paulo Souza

  Please note the answers and mark it as "answered" as appropriate.

• Cisco Telepresence Server/Cisco Telepresence driver/Cisco VCS - C / Cisco TMS license

  A big problem with the fact that I'm stuck is licensing. Really, I have tried many things to find the solution for it, but could not.

  I have actually made all of these servers (mentioned in the title) in my lab in preparation for the CCNP Collaboration certification at home.

  I am not able to complete some laboratories due to license issue (I guess). Y at - it an option to get the demo license for all these servers?

  I would be really greatfull if someone can suggest me the solution and/or the licenses required to complete all the stuff for my CCNP Collab tag.

  Best regards

  Dipak Singh

  TMS and VCS - C when installed without licenses, are automatically set mode of demonstration/test with some availability of license to test with. If needing a VCS-E, you will need to do to your account manager and they should be able to get you the time limited licenses good because I think that 90 days.

  Conductor Essentials is free, which means that you can install and get full functionality without the need of all licenses, but you are limited to 1 conference bridge and no grouping is allowed.

  TelePresence Server require licenses to function, once again, reaching out to your account manager for this.

  At the end of the day, you should reach to your account manager for all of this, as they should be able to help get timed license if you need.

• VCS - C license server

  Hi all, I have a question about the licenses from the VCS - C Server I bought for the demo. I have reset the factory default server and all licenses have been lost. What should I do now to recover the licenses?

  Serial number of the server is: 52AXXXXX. Software version: X7.1

  Hi, please contact cisco account/sales manager who had provided the VCS - C for the demo server and it will help to share the demo license.