Satellite P100-119: have no right to run Power Saver

Similar Questions

• Satellite M40-282: I don't have access rights to run Power Saver

  I installed GST when I reinstalled my new OS manually
  and I installed GST but he did not show up to reinstall after.
  In the control panel when I try to click the GST that it says 'cannot be opened because you do not have access rights to run Toshiba Power Saver '.

  But I am logged on as administrator for sure

  Hello

  It s very strange and unusual.
  Have you chosen the right drivers and you have everything installed correctly?

  I studied a little on the net and it seems that the M40-282 Sat has a serial number PSM42E and so take the drivers of the PSM42E series.
  (On the driver page I saw three different M40 accordingly large number)

  I discussed with other users, and especially incorrect installation was the problem. On the driver page, I found a statement of installation, and in my opinion, you should follow the guidelines in this document.
  Everything should then work. I hope ;)

  Check it out. Good bye

• Satellite P100-119 - software after the installation of recovery

  I use a Toshiba Satellite P100-119 since 2006. I want to run the original liveries Product Recovery CD after you back up all my data, so that with a vacuum system, the laptop gets even faster.

  But as there were pre-installed software (office, Toshiba programms) when I bought it, I don't know if they went after the recovery. I do not have CD for these programs, they were just pre-installed and what my Windows xp, should recover fully with the cd?

  Hey Buddy,

  After the installation of recovery, you have the same settings that bought the laptop. With other words recovery disk will restore the box settings.

  Firstly the recovery disk will wipe the entire HARD drive and remove all. After this Windows will be installed all the drivers and tools. In addition, will be also installed software preinstalled such as office, etc. and you can use it again. :)

  Backup all important data like the photo, music, etc. but everything will be removed for a clean install of Windows.

• Satellite P100-119: is it possible to upgrade the processor to Core Duo?

  I ve a Satellite P100-119 computer laptop with 1, 66 GHz (Core Duo). Is it possible to install a faster processor (2.0 Ghz Duo Core) in this notebook, without Exchange of the motherboard?

  Hello

  Toshiba doesn't usually recommend upgrading CPU and doesn t support these upgrades. Everything you make are at your own risk!
  In this case you will lose the warranty and if something goes wrong you will not get any support.

  Well, some people suggested that it is possible and that works, but I've never tried and cannot give you a 100% guarantee that it will work.

• Satellite P100-119: need driver GeForce Go for Windows Vista

  Hello I'm new here and got my first problem ;)

  I want to install Windows Vista Beta 2 on my Satellite P100-119, got a Nvidia Geforce Go7600 with 256 MB of ram on Pci - E in it and I want to ask if toshiba already has a driver for Vista? If all goes well! :)

  welcome them

  See this topic.

  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=13943&MessageID=50939웻

  Is not on the Satellite Pro but on Vista drivers at this time

• What memory can I add to my Satellite P100-119?

  Hello..

  I would like to add new modules of memory to my P100-119. Initially, it contains 2 Modules of Elpida, PC2 4200 (DDR2-533) with 512 MB per module. I would upgrade to 2 GB RAM and I have purchase 2 Modules of MDT, PC5300 (DDR2-667) with 1024 MB per module.

  I've built in the new Modules, but the screen remains blank, the system does not boot... BIOS is the newest Version 4.20 since November 2007 a the integrated Intel 945 PM Chipset Express also supports the DDR2-667 Modules.

  Where is the problem? Is - this incompatible RAM with the laptop?

  Hello Matze

  I presume that there is compatibility problem. If you want to have high quality and 100% compatible RAM module use:

  1 GB memory PC2 DDR2 (667 MHz) PA3512U-1M1G
  2 GB memory PC2 DDR2 (667 MHz) PA3513U-1M2G

• Satellite P100 - 194 defective Contact on the main power connector

  Hello

  Two and a half years ago, I bought my Satellite P100-194. Yesterday, I noticed that I can't use my cell phone on my diet. At first, I thought power has left his job, so I opened it. Today, I checked the entire power supply with a voltmeter. It still seems to work, it gives me twenty-six volts at idle.

  After that I checked the connector of my diet and I noticed that it seems not hold very tight in the case of the laptop. So I think that my connector has a contact in loose / faulty.
  After that I googled to find some people with the same problem and it was written that Toshiba may fix this loose contact by changing the whole motherboard for about three hundred Euros.
  Due to the fact that I am a student, I don't have that kind of money.

  Have you any advice for me to get my laptop working again?
  Or do you think I have a quite different problem?

  Thank you
  Bastian

  Thank you

  null

  Hello

  In my opinion, you should visit the nearest Toshiba service provider. Explain the situation and perhaps, they will be able to solve this problem without Exchange of motherboard.
  Maybe they'll just resolder the connections.

  Talk with them. Be just cool and pleasant. Maybe your charm will help you. ;)

• Can not run Power saver on my Satellite after installing SP2

  I can't install or run toshiba power saver on my Satellite A60. I've updated to SP2 on the windows update page and cannot run energy-saving. I tried to reinstall the software, but it still doesn't work. Ideas please!

  See you soon
  themalguy

  Hello

  You will find on the site Web of Toshiba Power Saver driver 2.32.0.3C and Power Saver utility 7.03.02. You must install both parties. Note: First the driver that the utility.

  Good bye

• Satellite A660 - 11 M on Windows 7, Toshiba Power Saver does not work

  I have a Satellite A660 - 11M and I'm working on Windows 7 Ultimate

  The problem is that I download all drivers and updates but the toshiba power saver does not its installed without error and TPSLaunch (green icon) does not open when I click on it and no icon, I found in the control panel for the afterIi program do not install the package any added value!

  Under Win7, it works a little different. TOSHIBA Power saver is part of the advanced settings ower.
  Enter the power management you are using and click on advanced power options. There you should find Toshiba energy savings.

• Re: Satellite P100-434: unable to load its running Xp Pro drivers

  I have a P100-434 (SPAD), which is running XP Pro, I decided that I wanted to rebuild the OS because it became very crowded and slow.
  I partitioned the HD and installed a 2nd copy of XP Pro with dual boot, but I find that I can not load the audio drivers on the NEW XP.
  The driver installation aborts and reports NO MEDIA FOUND.

  I checked the driver that I downloaded from the old installation of XP and it works very well, is the sound card and installs the drivers.
  I'm a bit of a loss as to why a vanilla OS install can't find the sound card.

  So can someone point me in the right direction to get sound? (I've reloaded XP twice with the same result each time).

  Post edited by: exraflad

  Windows XP needs * KB888111 * and * KB835221 hotfix * before MS site that you are going to install the audio driver.

  -You must install the two patches
  -Download the Conexant audio driver from the Toshiba page. I found two different versions. I would recommend checking both!
  -remove the old driver its the laptop restart of Device Manager and install the new audio driver download

  Greetings

• Satellite P100-126 Bios 3.5 can run Ubuntu feisty with acpi = off

  Is there a changed working with 3.5 bios dsdt? If I do not have acpi = off my GPU runs very hot (115 °) and I can't hear the sound. Thank you!

  Hello

  You know the website ww.acpi.sourceforge.net?
  There you might find help how patching the DSDT (differentiated system Description of Table)

• GPU on Satellite P100-217 fan never turns on running Linux Gentoo

  Hello

  I am running Linux (Gentoo) on my P100-217 (Geforce 7600). The graphic card fan never turns on, and the GPU gets to a temperature higher than 100 ° C when executing some 3d games. When I boot to windows, the graphics fan does not turn and the GPU is much cooler, running the same games.

  Can someone Toshiba please give me some information on how to solve this problem under Linux.

  Here is some additional information:
  Driver version: 1.0.9755
  nvclock version: 0.80.
  Nvclock message: you the fanspeed adjustment only is not supported on your video card type

  Thank you

  Chris

  Hello

  I'm not Toshiba, but maybe I can help you too.

  Type in the console:

  detection sensors

  and follow the instructions. Maybe you need to compile some kernel modules yourself.

• Satellite P100-119: display no longer works

  Hi all

  After resetting my phone and install the printer driver for the Epson homepage suddenly my screen image was strange looking. I decided to start the new laptop. But the display did not turn on either. Just the LED lights that surround it were black kept on-screen

  Try all to find a button for ignition and extinction of the screen has introduced the small result the display worked again for a few days and then all of a sudden with a new start over the same problem. I decided to connect it with an external display and to open the BIOS. I managed to start the windows safe and try to renew all the drivers.

  Suddenly the external display is turned off and turned back on the computer screen. I restarted the laptop without external screen and everything was ok - but only until the next day - now the problem is ongoing and I can just start with an external display in security mode.

  Maybe one of you knows the problem or can even help me. I would bring her to a service, but at the moment I don't have a lot of money to buy a new one or even fix it. At least, it would be good to know, in case, what would be the cost of repairs...

  Thank you very much to all those who answer

  Hello

  To me it looks a bit a graphics chip is malfunctioning.
  These behaviors are typical of the GPU issues.

  But have you tried to install a fresh windows OS?
  It would be interesting to know if this would be possible.

• Satellite P100-324: the Fans are still running

  Hi to you all,.

  Maybe you can answer me the question.
  Is it normal that my laptop fans are still running. I put the 'silent' settings in the bios and forced the laptop to run always on 1000 MHz, if I only use it for writing
  in Word or reading emails.

  It's really annoying. I don't know what to do.

  Thankz for your help in advance

  Michael

  Hello Michael

  It is nothing unusual that cooling fan runs constantly on low speed. On modern laptops, there is a powerful hardware that needs to be cooled correctly. Especially many different processes are active in the background and CPU is standing under pressure. Not much when you use just the laptop for writing, but obviously enough to increase the temperature of the CPU.

  Try it please set the CPU and cooling to a minimum level method. Also check the Task Manager and end the process, you don't need. Maybe this will help!

• Satellite P200: Cannot open the Power Saver - fatal error in Windows XP Home edition

  Hello

  I just installed XP and I came across a problem that is boring. When I finished to install Power Saver and the driver, I got a message saying fatal error and I thought it was because I haven't restarted. Then, after only a day or 2 later I went to the energy saver and he said cannot open because you don't have access rights to "Toshiba Power Saver.

  Is there a solution to this
  Neo-Tech

  Hello

  I put t know if this is a solution but try my proposal:
  First of all, remember that you are registered as an administrator or make sure that you have administrator rights.

  Remove your old system energy saving. You must remove the driver and utility.
  Then reinstall the computer and clean the registry using the freeware like CCleaner.

  Then install the driver of saver of power and after reboot the new install standby power plant.

  I hope it helps