Satellite P300 PSPC4A - BIOS no updates required for Win 7?

Similar Questions

• Satellite P300 (PSPC4E) - BIOS is damaged

  I have some problems with my Toshiba Satellite P300 (PSPC4E).
  The BIOS is damaged and I am trying to get it back.

  I disconnected the battery, HDD and DVD.

  I managed to create a USB startup disk using the USB HP and CrisDisk.
  It was empty after I run it. I copied the three files into it, PHLASH16. EXE, Autoexec.bat and my laptops bios, named bios.wph (version 4.20).
  CrisDisk using the required files are transferred automatically.
  I tried plant key combinations, following the instructions of starting (USB->-> start button / stop power cord), such as the FN/WIN + B / F, FN/WIN + ESC.

  When I boot with FN/WIN + B / F, it starts only upward 'normally', all the lights on and the screen remains black. USB is not flash or anything.
  Using FN + ESC is another story, well that without LEDs light up, except for the power button.
  The USB flashes, for a few seconds, and shortly after, the laptop starts to beep.
  When I say beep, it really will beep, loud and clear that h * l! 1 long beep 2 short beeps, who will be permanently.

  I left it for about 10-15 minutes, but nothing happened. The tones were really strong, so I stopped it.
  I tried to make the combination of keys without connecting to USB, and it did the same thing, 1 long + 2 beeps.

  So, I'm doing something wrong here?
  Also, I wonder if it is possible to reduce the volume of the beeps.

  Would be really grateful for any help I can get.

  Hi mate

  I found another thread interesting here in the forum are contiguous similar question.
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=54395

  Maybe you could try the workaround posted by user ale210.
  But if it does not, you will need a help from a specialist like Toshiba service technician.

• Satellite P300-1 has 8 - part number for the AC adapter / CC

  Hello.

  Can anyone tell me the part number of the AC adapter I need to buy for my Satellite P300-1 c 8?
  Model No.: PSPCOE-01H008EN 15550 / 1024/1024/160 G 54/17W + BT/D52/L/M/L

  The toshiba site list or recognize the model, CarPhone Warehouse does not provide me with detailed documents and the original adapter was stolen. If not, can anyone provide an email address for toshiba (I am unable to call during their office hours).

  Or failing that, some general tips on an adapter compatible Please, I bought an adapter for the correct base - 19V, 3 specification. 95 a, (75W), Connector (PA3715E-1ACE) 2.5/5.5mm however, it does not work. The toshiba site lists another card of the same specs (PA3468E-1AC3) but I am reluctant to risk without being sure that it is just to buy it. I'd be happy to buy a universal adapter but only a high quality which will not be an electrical danger.

  Thanks in advance for any help.
  Clare

  Hey Buddy,

  You can search for options and accessories here:
  http://EU.computers.Toshiba-Europe.com/innovation/generic/PC-options-Accessories-EU/

  Why you need an email at Toshiba?
  If you have questions about spare parts, you must contact a Toshiba instead authorized service provider.

  In general, I would recommend the original adapter because it of tested and designed for your laptop. With other words, it s a product of high quality.

• Photosmart C8180 All-in-one: HP Photosmart C8180 All in One updated required for memory problem

  Very slow images scanning and cropping, image rotation distorts or does not complete. Poor IQ, sometimes with thin horizontal stripes. Message says update necessary for the solution Center, little memory but what update? Have tried to unplug the power and usb, turning works but no improvement.

  Images are for the publication, so 16-bit, 1200 dpi sometimes, so need memory, but will send you directly on the external drive in order to preserve space on the laptop.

  Hi sandie4747,

  Thank you for your answer!

  Another option for you is to go through this how to scan guide, how Scan: Windows 7and try scanning without software HP, in this way, we can see if there is a problem with the software or the scanner, as there are a of other methods of scanning available.

  Please try some of the alternative methods and let me know what happens!

  I hope hear from you soon!

• Satellite L650 - can not find audio driver for Win XP

  I have a Toshiba Satellite L650 and one can not find a driver of his work for Win XP.
  Not even on the official site, the drivers do not work...
  He said no soundcard found

  Please install drivers.
  What should I do? THX

  Hello

  What L650-xxx you have exactly?
  The European driver Toshiba offer page two different drivers audio; Driver audio Conexant and ATI driver sound.

  Please check exactly the sound card, and then use the right and proper sound driver.

  PS: Make sure that Win XP is up to date! You must install all patches, service packs and hotfixes before installing the audio driver.

  Welcome them

• By Satellite L755-17r spec meet the requirements for farming simulator game?

  Could anone look at this and advise please?
  My son bought the game for him and it worked fine far at the beginning but suddenly refused to start properly and if it isn't the game screen is empty, even if the screen moves when the controls are in a hurry.

  I don't know about the spec on graphics card so looking for some advice
  My graphics card is the Intel HD 3000, the game conditions are

  256 MB of vram
  nVidia Geforce 6800 series
  ATI radeon x 850
  S3 chrome43o gt

  My laptop model is toshiba Satellite L755-17r 4 mb ram, 620 gig and 2.1 ghz.

  I thank in advance

  Hello

  It seems that you play an online game that runs in the Internet browser window. Right?

  First of all these games have not need of high performance computers.

  Therefore the specifications of the laptop should be ok.

  I recommend the first graphics card driver update. Visit the Toshiba driver European page download the compatible driver and install the graphics card driver.

  Also I recommend that you check the different Internet browsers like Firefox, Chrome, Opera or the latest IE 9

  Welcome them

• BIOS and drivers required for CQ45-106AU for OS Windows XP or Free DOS

  Hello, I bought laptop Compaq CQ45-106AU which has Windows Vista Home Basic OS and I am unable to find the BIOS of motherboard, Chipset drivers and all drivers for this perticular computer laptop, I want this downgrade to Windows XP Pro or I want to to Free DOS so if anyone has the solution to this then please send me information as soon as possible. Thanks in advance to all who pass by this message.

  I recommend you stay with VISTA.

  This chip Audio IDT using model and ENE CIR receiver driver XP were hard to find.

  ENE CIR is essential if you have purchased the remote for this model.

  Some of the user CQ45 found they will lose control of BRIGHTNESS setting (Fn + F7 and F8) due to the incompatibility of the QLB software.

  However, if XP is essential for your applications please perform steps below.

  ____

  Your model must sata driver AMD sliptreamed on XP installation CD.

  If you did it right, you'll BSOD error.

  Use Nlite to slipstream sata driver AMD.
  A good guide for driver sata sliptream, here

  Note: Do NOT use this guide sata driver, your sata driver is given below.

  AMD SATA AHCI Controller Pilot, here

  or

  If you want an AMD SATA driver from HP site, here

  extract sp39719 to a folder and use the files in the RAID7xx folder

  Note:

  Select ONLY x 86 AMD SATA AHCI driver

  Download nLite , here

  Make your Vista recovery cd/DVDs if you have not yet discovered it here

  _____

  Try the following drivers,

  Drivers XP for CQ45-106AU

  Install .net Framework before the others, here

  Suite software Catalyst (for your Chipset ATI, HD 3200 Graphics/video and LAN drivers here

  Audio installation is the most difficult part, since the BIOS incompatibility.

  Install MS-SAU first, here

  IDT High-Definition Audio CODEC Pilot,

  a version update of Microsoft Update Catalog here

  or

  or if you want to install HP IDT driver (VISTA), here , some user indicated that it also works with XP

  or try the new version here

  Note:

  Some users CQ40 CQ45 must update their BIOS to fix Audio that disappeared after rebort.

  If you have found your BIOS is lower than F33A, update your BIOS to the latest version here

  High-Definition Audio (HDA) Modem Install drivers, here

  Broadcom Wireless, here

  Realtek RTL8102E Family PCI - E Fast Ethernet NIC, here

  JMB38X card reader Host controller driver, here

  ENE CIR Receiver (your Vista driver), here

  or if it doesn't work try Vista driver checked Intel, here

  HDMI Audio, here

  ALPS Touchpad Pilot, here

  HP Quick Launch buttons, here

  If you have Bluetooth, here

  If you had for 7 unknown devices (buttons drivers), here

  Installation-> right click machine.inf, choose install.

  Good luck

  Message edited by Mariza on 04/01/2009 12:11 AM

• Compaq DV7800: A Bios Configuration is required for the PCIE graphics card

  HII

  I have a small form factor dc 7800 Desktop

  And I also have a Nvidia 8600GT graphics card

  When I mount the graphics card on the computer PCIe slot

  would you like to work in VGA connector and when I use tha Port DVI form map

  Nothing... So I need a Bios Config to work?

  For the factor, I put the motherboard can configure the card

  I have all the equipment, power supply, HARD drive...

  Can you help me?

  Thank you

  This card is perhaps too powerful to 240W power supply that has your PC.

  I would go with a less powerful card like the Radeon HD 6450.

  Also before installing the video card, uninstall you the card integrated Intel graphics and check the driver to uninstall before installing the nvidia card?

  NVIDIA used to list the current of each of their cards, but now when I click on the sheet for the 8600 GT, I get very little info.

  http://www.GeForce.com/hardware/desktop-GPUs/GeForce-8600-GT/specifications

  The PCI x 16 slot in your PC has a certain power of only 25W max draw and I'm sure that the 8600 GT draws more power than that.

• Satellite P300-24 t cannot find drivers for OpenGL for Windows 8

  Hello

  I bought around mid-2009 this laptop student a Gamedeveloper (P300-24 t), I needed a decent laptop with some graphics cards now because I have to be able to create games on it. Now I have recently installed Windows 8 because I need it for my studies.

  But the problem is because I now upgraded from 7 to 8, I found not the OpenGL drivers decent more because with every driver I'm trying to install on my computer Toshiba laptop my OpenGL support keeps hanging on the default version 1.1 just now when I need OpenGL 2.1 + for my last post.

  When I run our assignment it crash and tell me that I need better OpenGL drivers

  So my question: is there a way to install the OpenGL drivers on my laptop.

  Vidcard: Ati Radeon Mobility 4650

  See the pages of a few 3rd party like www.omegadrivers.net
  But the use of these drivers is always at your own risk!

• Satellite P300-156 - where is the slot for Bluetooth module internal?

  Someone can say where, inside the laptop's slot to install the internal bluetooth module?
  I found only the second pci-e slot, but under the keyboard, I see the small slot located at and I did not now what is it?

  Help, please

  Hello

  I put t know what slot, you've seen, but as far as I know the connector on the Bluetooth module should be placed close to the connector of the card.
  However, the Bluetooth module is not installed on this notebook.

  Good bye

• Missing satellite C870 - 11G - "SM BUS controller driver" for Win 7 64 bit

  Good afternoon

  After extensive research of the forums, I was unable to find a solution so far.

  A few months ago, after the demise of his previous Satellite, my friend has acquired a Satellite C870 - 11G on Windows 7 (64-bit).

  She acquire the machine online from PC World, and after that make the updates of windows put in place using the Zonealarm free firewall & 2013 AVG antivirus free. We have installed the Microsoft Office 365 and the bundled drivers for HP Deskjet F4180 sound.

  Initially, everything went very well, but a month ago, the machine does not recognize the printer.

  After the troubleshooting thing, the machine has reported a "SM BUS controller driver" as being missing.

  "Search etc, after much net more faffing autour with the restoration of the system", I could not yet set and so went to the "nuclear" option i.e. I backed up all its data and doing a complete reset of the recovery partition.

  We have gradually been put back together, reload its data, re-installing of ZoneAlarm and AVG, Picassa & Office 365. Yesterday I went to re - install printer drivers, but before doing so checked Device Manager to see that the error "SM BUS controller driver is missing" was. Grrrrr...

  I tried to use system restore to return point of restoration of a restore point but that too now fails every time with error (0x80070005).

  Before we go again nuclear, anyone has any ideas please...?

  Best regards & thanks in advance.

  Larry

  Try please reinstall the chipset driver. I found this for your machine and you can download it here.

  Test it please and post comments.

• Satellite A100 - 011 PSAARE: need player modem for Win XP Pro

  Hi dear all

  gently, I need xp PRO drive modem Satellite A100 - 011 PSAARE OR what is the way to install it.

  Thanks & best regards,

  Hey Buddy,

  you need a modemdriver for XP? Where you are looking for?
  Maybe you can find the driver you need here:

  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp (European site Tosh)

  http://209.167.114.38/support/download/ln_byModel.asp (Toshiba Canadian site)

  Good luck
  Greetings

• Satellite P870/026 missing after update 8.1 Win 5 GHz wireless

  Miss me my wireless 5 GHz on my laptop, it's no longer on the list after that I updated to Windows 8.1

  Anyone know what is the solution? I have contacted Netgear, and they said to contact Toshiba to try to solve the problem of driver for Windows 8.1

  You updated the Windows 8 to 8.1 Windows such as advised by Toshiba?
  http://support.Toshiba-tie.co.jp/windows81/update_au.htm

  Some of these elements will have to be uninstalled before the update to Windows 8.1. However not all of these elements may be present on your laptop
  List of components
  Atheros WLAN card driver
  Genesys Logic card reader
  Intel Proset
  Intel Wireless Display
  TOSHIBA PC Health Monitor

  After that you could install Windows 8.1 and could follow with the update driver Win 8.1 and the new facility.

• Satellite C850D - 11 c PSCC2E - CHIPSET driver for Win 7 64 bit necessary

  Hello

  I have been stuck in a long convo the techsupportforum courses and was finally told to try here.

  So, I own a C850D PSCC2E - 11 c Satellite with Windows 7 x 64.

  I can't find the driver of my laptop chipset in the list of drivers.
  I first tried to install all the drivers available, but it is obvious without a chipset, I'm having problems, and I do it.
  USB ports do not work as they should etc.

  Where is the driver for chipset for the C850D PSCC2E - 11 c?

  Thank you!

  Hello

  Your laptop is equipped with a graphics chip Ati (AMD).
  This means that the chipset too AMD.
  According to some information that I found on internet, AMD A68M chipset should be built in Notepad.

  Furthermore AFAIK ATI chipset driver is part of the ATI/AMD graphics card driver and that's why you should install the GPU driver for the installed chipset driver

• No satellite P300 - 18 M no wireless connection with Win XP Pro

  Hello people!

  I recently bought a P300 - 18M and installed Windows XP Pro SP3 on it. Everything works fine except the wireless connection. He know the switch for wireless connection is disabled because it is not all networks, although the switch is on and the wireless LED is lit.

  I checked the FN + F8 keyboard shortcut, I chose wireless only here...

  I downloaded the Intel drivers latest 5400 for the network card, but it is always no network :(

  Who can help out me?

  Hosts the Netherlands, Leon

  Hello

  There is also a WLan switch on the side of s for laptop.
  This switch must be activated also.

  Please check this!

  In addition, you can consult the WLan card properties in Device Manager.
  There should be an Advanced tab.

  There are different parameters, you should check out. For example, you can choose different WiFi standards such as 802.11 A B G, etc.