Satellite Pro 6000: What WLAn Module?

Hello
Anyone know which Module WLAn can be used in a Satellite Pro 6000.
My NB is pre-installed for WLan but I don't want to use only 11MBit Module and the other are not signed for the SP6000.
Can I use this module to 54 megabits?
Thank you
Daishi

Advertisement

Hello

As far as I know this unit supports only the 802. 11b Wireless LAN Mini PCI Card.
This Mini PCI card, I got with a flow of data 11Mbit.
In this case, I think that you can use a Mini PCI card with 11Mbit.
But nevertheless you ca also use a PCMCIA wireless card. This card is also available with 54 Mbps data rate.

Good bye

Tags: Toshiba

Similar Questions

  • Satellite Pro 6000: what is a 3rd Brown cable to WLan?

    I recently bought a second hand toshiba satellite pro 6000. When I bought the wireless adapter is not connected correctly, the black and white wires are connected to the mini pc card, but there is a Brown wire with the same end of the connector that is loose.
    I don't see where it is supposed to go, and the result is that the quality of the connection is bad at 13%.

    If anyone could tell me where this third cable must be connected to it should enhance my quality link (the signal is excellent at 100%)

    Thank you.

    Hello

    The 3rd cable does not for me but maybe it's for BT. as far as I know that you need to connect only 2 cables to the Board of Directors to use the Wlan. The performance has nothing to do how many cables are connected.
    The white cable usually goes to the hand and the black to the auxiliary voltage

  • Re: Satellite Pro M40: what memory modules that I can use

    Hello

    I was hoping someone could point me in the right direction.
    I have a Satellite Pro M40 part number: PSM46E-00H002EN

    I really want to upgrade the memory, but I don't know what to do.
    I know I want two 1 GB ones but I do not know what kind.

    I looked and there seems to be so much of.

    Could someone tell me exactly what I want or give me a link to buy.
    I would be grateful rerally.

    Hello

    I think you should check this page from memory Satellite Pro M40:

    Memory for Toshiba Satellite Pro M40
    http://www.orcalogic.co.UK/ASP/ProdType.asp?ProdType=26119&ft=m&St=3

    It is said that you could use the DDR2 533 MHz (PC2-4200) 200-PIN SODIMM memory modules and you could upgrade the memory up to 2 GB of RAM

    Good bye

  • Is it possible to get the WLAN for Satellite Pro 6000

    Hello!

    I have a Satellite Pro 6000. Is it possible to get a WLAN-modul for this laptop?
    Can someone give me the room-no. ?

    Thanks, Michi

    According to the specification for this model of laptop, it must be PA3070U-7MPC.

  • How to get Wlan working on the Satellite Pro 6000 Win2000 Sp4

    Hello
    It is possible to get the wlan is working on a Toshiba Satellite 6000 under Windows 2000 Sp4?
    There are many indications in other Threads, but nothing has worked.
    Does anyone have a step by step instruction?

    Thanks for the help,
    Nico

    Very important to know if your Satellite Pro 6000 laptop was equipped with WLan car or not!

    If the wireless network adapter is available please check if the right WLan driver has been installed and if the wireless network adapter has been properly recognized!

    I searched a little one found that the wireless network cards optional to this series of laptop; This means that some 6000 Pro will be delivered with the Wlan card and some books don't have this module!

  • Satellite Pro 6000: can't find the right WLAN driver

    Hello
    I have re-installed Windows Xp on my laptop Satellite Pro 6000. Everything works except for the wireless connectivity.
    When we look in the Device Manager, I see that the WLAN driver has not (or wrong) was installed.
    Then looked at the Toshiba site for the drivers, but I am not able to find the right one. I found some drivers, which seems to be the one, but unfortunately after installing the drivers, wireless connectivity is still not available.
    Any help would be appreciated.

    Thanks in advance.
    Best regards, Robert

    Hi Robert

    Stand by! Connectivity is not available or the WLAN card is still not installed correctly in the Device Manager list?

  • Satellite Pro 6000: error LED message - what does this mean?

    Hello

    I have gad an old Toshiba Satellite Pro 6000. Sometimes, not after a period, he died. I have gad error code because the DC IN Red flashes orange. The blink rate is 1 x 3 long short 1 x length 2 x 1 short long = 10001001 in bin = 91 h (is this true?)

    Now 91 h ist the following error: 1R5 - E1V voltage is not more than 1.275V when the computer is turned on. But what the hell of this error means? What is 1R5 - E1V?

    Need help. Greetz

    Hello

    Read the code back!

    10001001 = 1001 0001 = 91 H
    http://www.prepressure.com/library/BinHex.htm

    I think there is something wrong with the electronics of the Board of Directors.
    Therefore, you will need to contact the ASP from Toshiba for help.

  • What are Satellite Pro 6000-compatible DVD - RW drives

    Hello

    Can someone tell me which dvd rw is compatible with the satellite pro 6000?

    Hello

    It is always difficult to find information on compatible drives due to different master / slave and c - salt settings.
    In my knowledge don Toshiba user manuals t provide such information. OK, I put t know if all don t user manual provide this, but I've found this info in my user manual.

    However. I studied a little someone suggested that the Toshiba SD-R6372 dvd recorder is compatible with Satellite Pro 6000/6100 units.
    I found this on a very popular online auctioneers ;)

  • Satellite Pro 6000; sleep function does not work after upgrade W98 SE to XP

    I bought a windows XP cd and installed on W98 on my Satellite Pro 6000. The sleep function does not work now. I probably need a software of Toshiba. What do I need? Where can I find? What is the order of installation?

    Hello

    All drivers Windows XP Home edition, tools and utilities you can find on Toshiba support page under http://eu.computers.toshiba-europe.com > support & downloads. You have old laptop model and because of this type of product, you choose option ARCHIVE.

    Order of the facilities is as follows:
    -Windows XP
    -Display driver
    -Audio driver
    Toshiba - common modules
    -SD Card host driver
    -SD Card Driver
    -BlueTooth Stack
    BlueTooth - Easy Connect
    -Mouse driver
    -Modem driver
    -LAN driver included with Windows XP
    -Infrared driver
    -Toshiba Power Saver
    Utilities - Toshiba
    Toshiba - post Mobile
    -Toshiba Console worm.
    -Toshiba Hotkey for display devices

    I hope that you will be able to install Windows XP Home edition successfully.

    Good luck!

  • Satellite Pro 6000 memory

    Can anyone help?
    I am buying a memory module 128 MB for satellite pro 6000.
    The manual says I can only install a 128 MB module with PA3126U - 1 M 12 part number.
    I tried two different memory sites that said they had compatible modules, but they have turned out not to be compatible.

    Hello

    your laptop uses PC133 SDRAM. Normally, it should not matter what manufacturer.

    Good bye

  • Unable to connect satellite Pro 6000 network

    I would appreciate help on this. We have a Toshiba Satellite Pro 6000, which we assumed is active wireless. But when you turn on the wireless switch, there is no answer and the laptop will not come to look for me or any other network.

    I was able to connect using a USB wireless adapter, but it seems a shame not to use the capacity of the machine itself. Any suggestions? And I'm just thinking wireless is standard with this model. If not what can I do about it?

    Hello

    Please check in Device Manager if the WLAN card is listed under network adapters. As far as I know the WLAN card for this camera is optional and it is not standard.

  • Satellite Pro 6000 - how can I update the BIOS?

    Hi all

    I have the problem that my laptop does not start 9 of 10 times with the message: * block 1 BIOS is damaged, call your service man.

    I want to update BIOS but for the Satellite Pro 6000 I can only find an update the BIOS from Windows. But my laptop does not start! Rarely the machine starts, but when I try to update the BIOS, I get the message that I already have the latest version of the BIOS

    My questions:
    * Is there a BIOS update file that is a BIOS floppy? (for example the Satellite Pro 6100 has 2 BIOS files, 1 Windows and 1 making a floppy disk)
    * Is it possible to update the BIOS with the same version of Windows?

    Or perhaps there is another solution for this problem? Has no need to update my BIOS?

    Thank you.

    Hans

    Hello

    I agree with Luke.
    The rom Bios module seems to be damage.
    Either it must be replaced or flashed again.

    But you won't be able to do that! The update of the Bios on the Toshiba page focuses on winning and you will not be able to update if the windows are not running.

    You last chance is an ASP that could check the BIOS ROM.
    As I said, most high, maybe new reflash module Rom help but cela can be answered simply by an ASP technician who checked this.

  • Satellite Pro 6000: display or graphics card problem

    Hello
    I don't have a model satellite pro 6000. PS600E-01NYE-FR
    1 GHz P3, 20 GB HDD, wireless bluetooth not running XP

    I understand that it is an old laptop but had been treated with great care because I got it.
    My problem is the following;

    Startup of the laptop is a route very well, but for some reason together and after no set amount of time the display fails
    a wot is visible on-screen is hundreds of tiny colored blocks, sometimes random horizontal lines
    but nothing is readable, at all.

    I tried to run a yellow one also using the video output external monitor, all appear the same.
    a computer display (although I can't check it out) to freeze.

    I replaced the heatsink fan as a precaution (using the new dough)
    the only solution I can find is replaced the ram with
    2 x 256 MB Sync 133 mHz module Samsung. This could be the problem or can anyone shed some light on this for me.

    Thanks in advance
    Display Toshiba SP6000 (?) Problem

    I am not a technician, but I assume that there is probably a problem with the video card. I'm afraid there is not much to do. You should contact the service and make them run tests to verify the functionality of the video card. If the card is faulty, just replacement will help.

  • Satellite Pro 6000: Base system device driver for XP

    Hello

    I want to install the:
    M - systems diskonchip 2000

    and the:

    Base system device

    On my Satellite Pro 6000 (XP).

    Does anyone know what I need to install drivers?

    Hello JR

    Did you install chipset driver?

    On this page of European driver for Toshiba-> * Archives *!

    http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp

  • Updated by Satellite Pro 6000 with a DVD burner - technical question

    Hi all, I just bought a DVD burner that is adapted to the Bay of selection to replace the old DVD player...
    He came 'naked', so I thought I'd just disassemble the frame of the old drive and put it on the new...

    But: not the slightest Phillips screwdriver will integrate these screws; in fact, they look very special and I do not know how to remove...
    Should I have any instrument/tool special and if so, where do I get it? Maybe I'm too blonde...

    Someone here who can help?

    Thanks in advance! lionesse62

    Hello

    You need a special screwdriver to remove the module bay select (CD/DVD drive).
    A 2 mm screwdriver Phillips, a pilot of flat blade screw 4mm and a LHSTIX of 4mm screwdriver.

    I think you should visit a laptop computer technician if you n t have the right tool to remove these screws.

    However, if you want to remove the module bay select the Satellite Pro 6000 laptop then follow this instruction;

    (1) turn the computer
    (2) when the lock screw is in the locked position, remove the screws and fix it on the hole to keep her temporarily locking screws.
    (3) slide the lever and pull place the selectable bay module.

    After you remove the DVD rom, you need to remove the connector and the connector cover. The connector cover is fixed with screws of black 2M2x8 liaison.
    The frame is blocked with five super flat head white M2x3 screw.

    As I said, if you can not remove these screws and then ask a technician for help.

    Good bye

Maybe you are looking for


HashFlare