Satellite Pro 6100 USB problem after stand-by

Similar Questions

• Satellite Pro 6100: USB port does not work after the return of the mode "Eve"

  I have a strange error on my USB ports on Satttelite Pro 6100 with XP SP2.

  Two USB 1.1 ports work fine after cranking up what the laptop goes into mode 'sleep' (automatically or manually).
  The restart afret optical mouse connected to the USB port does not illuminate and the XP system displays the error message on the device not recognized on USB port.

  Plug the mouse on or off doesn't change anything. Only restart helps.

  Any ideas?

  It's very strange, but it will be interesting to see if the same problem persists with other USB devices. Can you test and post again on the results?

• Satellite Pro 6100 USB XP SP2 remove USB device after suspend

  I have a Pro Satellite XpPro 6100 running.
  I have a problem since I installed SP2 of XP in that USB falls when the computer wakes from sleep.

  The computer is up there, but I can reproduce this with SP2 only. Fortunately, I did a Norton Ghost and I restored the status of versions prior to SP2 for now.

  It does not matter what is connected to the USB port, or which port it's plugged. Out of sleep causes a ToolTip message in the taskbar on an icon that represents the USB port - and the message says 'USB device not recognized '.
  I can't find any help on the microsoft site, nor on the discussion group. I am at a loss as elsewhere where I can watch.

  Thanks in advance for any comments.

  Hello

  I put t know what USB device you use, but it is known to me that some external devices like DVD-ROM doesn t support the standby or hibernation. Try to remove the unit from the USB port and plug it back. I'm sure it should work again.

  Good bye

• Toshiba satellite pro m30 USB problem

  I have toshiba satellite pro m30 and HP scanjet 4600 scanner.when I connect the scanner directly to the notebok with its ' original usb cable there is no problem. But if I connect the scanner to the laptop with a laptop usb extension cable cannot initialize the scanner. There is no problem if I connect the scanner to the VAIO laptop with usb extension cable. What can I do?

  Hello

  could you describe the difference between the original USB cable and the USB extension cable?

  The laptop and the printer works correctly with the original USB cable, but it seems that the extension USB cable is an inexpensive which does not fulfill the technical specifications and the laptop has a problem with this issue.

  To solve the problem in my opinion you could do an update of the BIOS, look if for your printer is a new driver available and reinstall the USB drivers.

  Also, you could test whether USB, the same problem occurs with other cables.

  Bye Bob

• Satellite Pro 6100 slowy starting after crashing

  My Satellite Pro crashed recently and since then has worked ridiculously slowly, not only in windows, but start upward. Any ideas on what I can check to see what the problem is and we hope to resolve this?

  Hello

  What do you mean by crashed?
  Replace a few parts such as HARD drive?
  Usually if Notepad starts slowly, you should check the boot order in the BIOS.
  Try disconnecting additional devices if you have connected some external devices to the laptop.

  In addition, you can try running chkdsk to check the HARD disk for errors.

• Satellite Pro 6100: blue screen after overheating problem

  My laptop overheats a year ago and since then I can only use it for about an hour at a time. First sign, it's going to blue screen, it's the hard drive starts clicking and about 5 minutes later, he dies.
  Let it cool down for a few hours, then it is well again. It is not the disc hard as I tested it in another laptop.

  Any ideas?
  I desperately need to work again, it has been the best laptop I've ever owned, and I hate the idea of having to buy a new one with a touchpad.

  Hello

  Generally, the laptop overheats because the cooling module may not work correctly.
  I guess that the blue screen appears because of the overheating.
  In this case, I would recommend checking the cooling fans. Fans cannot work properly because of the dust and debris.
  The use of the vacuum cleaner is the best way to clean the fans.
  But be careful.

  In addition, the square around the laptop must be free. It is important that fans can take a breath.

• Satellite Pro 6100 - USB host controller

  USB host controller

  Hello

  And what do you know about USB host controller? Do you need drivers or you have problems with the USB ports?

  Please explain your problem detailed in a few English phrases that others here can help you.

• Satellite Pro 6100 - INVERTER PROBLEM

  Hello

  I have a problem with my Toshiba 6100 (2 Ghz Version).

  My screen flashes 3 - 4 times, becomes dark and 2 seconds later the image disappears.

  This problem is known as a FL inverter problem? Someone had a similar problem as mine?

  I think that has to deal with the automatic shutdown of the display function, but I do not know if it is controlled on the motherboard or on the circuit of the inverter.

  Does anyone know more on this subject?

  Thank you for your help

  George

  My problem is solved.

  I removed and reinserted the graphics display adapter. Maybe he got loose or contacts obtained in the dough.

  Now everything works fine again.

  If anyone has a similar problem... maybe it's the source :)

  People Bye

• Satellite Pro 6100 - after updating the BIOS, it does not

  Hello

  I am trying to upgrade my old of Satellite Pro 6100.

  I started to upgrade the Bios via download from Toshiba (using WIN) site - OK downloaded zip files and installed, machine then stops. Problem, it does not restart - it's so now I have a laptop 'death' that is not responding to any key I tried.

  Any suggestions of resuscitation?

  Already I've updated from XP to SP2.

  Thank you

  Paul

  Hello

  It sounds like that the BIOS update has failed and your laptop can start t again. But try this workaround:
  Remove the AC adapter and the battery and then wait an hour. After that reconnect the adapter AC/DC and battery. Try to start the laptop.

  If it doesn t work I think that the motherboard needs to be replaced or you go to an authorized service provider. Technicians can reflash the ROM module
  But maybe you can find a motherboard of second hand cheap on eBay

  Good bye

• Satellite Pro 6100 stops after 15-30 minutes

  My satellite Pro 6100 Cup after 15 to 30 minutes of operation on power outlet. There is a noise and all the lights go out except orange slow flashing (power problem). I have restore by removing the power cable and wait a while.

  It will then start again. I used two different adapters and two different batteries. It also happens if work on AC with no battery in the. My suspicion is an overheat cut-out. The Sat Pro has a? Could it be clogged with dust inside (it is 5 years old)? If yes how I clean. I don't think it's a fan failure because I can hear the fan cut in. Advice much appreciated. Thank you.

  > Could it be clogged with dust inside (it is 5 years old)? If yes how I clean. I don't think it's a fan failure because I can hear the fan cut in
  I agree with you and the user SambadeAmigo. It seems like a simple problem of overheating and so the laptop automatically stops to prevent the equipment from damage

  I assume that your laptop can be enabled again after being allowed to cool. It is a common question if the cooling modules may not work properly because of the dust and debris.
  As suggested, it would be possible to remove dust using the can of compressed air.
  It should work.

  See you soon

• [u] [b] Satellite pro 6100 + external projector problems [/ b] [/ u]

  Dear friends,

  I am trying to solve this problem:

  When I connect to the satellite Pro 6100 a 3rd party bCool XG1 DLP projector (a very good) I can see everything fine except DVD.

  I better explain: I can see the movies on the screen of the laptop, but nothing on the wall...

  Notice that I can look at these files directly on the screen, but on the wall...:
  MPEG files (Quick time Yes, but not WinmediaPlayer);
  AVI files (Quick time Yes, but not WinmediaPlayer);
  MOV files (Quick time Yes, but not WinmediaPlayer);

  DVD: (With Intervideo Windvd) Ok on the screen, but no output from the projector.

  Note that if I use the small window mode, the projector output image is correct except inside the window that is displayed in black (but is OK on the screen of the laptop).

  Who can help me?

  Thanks in advance.

  Stefano

  Hi Stefanohf,

  When you pass the output mode you have with keys FN and F5?

  also what settigs are set in the display driver? Right click on desktop, properties and parameters.

  go to advanced and nView. There should be active clone!

  Try this!

  Goodbye, Sam

• Solution found to the problem of "BAD RTC BATTERY' on Satellite Pro 6100

  Hi, I'm from the Italy.

  I myself have solved this problem without changing the motherboard on my laptop second hand satellite pro 6100.

  for info: [email protected]

  Hello

  may I ask how you solved this? I have the same machine and this error pops up sometimes.

  Welcome them

• Satellite Pro 6100 - problem starting (light flashing Orange)

  On my laptop Satellite Pro 6100, seeing DC IN (first on the left) flashes orange and the laptop does nothing else (no display or sound). The light flashes for 8 times, has a long pause and then starts all over again.

  I tried a different adapter with no joy. It does the same thing if you use only the battery and if you run from the adapter without the battery.

  The only time wherever it shows a different light is when you take the battery out, put back in and hold the power button. Led Slim Select Bay (second right) briefly turns green, but it turns off and the led DC IN resumption of the orange blink.

  It seems likely that it is an internal hardware problem (power supply, motherboard, etc.). Does anyone have any ideas? And as anyone knows anywhere which lists all the different orange light codes for Toshiba laptops?

  Hi André,.

  You are right in thinking that there is a hardware failure (most likely your motherboard). Flashing codes are used by service technicians to indicate the nature of the fault and I have yet to find anywhere who publishes the real meaning of these codes.

  I think it looks like a trip to the nearest Service Agent. :-(

  HTH

• Satellite Pro 6100 - code beep at startup

  Hi all

  Just picked up a 6100 Pro of the Satellite with a few problems.

  It lights up, he pointed out the HARD drive and I can hear the disk activity. However, the screen remains blank and a single beep can be learned after 20 sec. White screen, as I understand it, is probably the issue of Council power raging in the SP6xxx series. However, the beep I do not understand.

  I know that 2 beeps or 3 beeps is incompatibility of memory but no one knows which denotes the beep?

  Ta

  Hey Buddy,

  To be honest it's not easy to say what the cause of the problem because it could be everything and Satellite Pro 6100 is old enough for laptop.

  You have two memory modules RAM? If so remove a module. Always try a module only at the same time and test it in the slot of RAM A and B. A module is may be defective or a slot.

  If this is not the case, there seems to be a problem with the motherboard or the CPU itself. If you can exchange these things, try it yourself as a repair would be too expensive for this good old classic I think.
  Second hand spare parts you can get it on eBay s worth a try! ;)

• Satellite Pro 6100: black border to the right of the screen

  After a new installation with windows xp when I star tup I have a black border (1.5 cm) to the right of my screen.
  After the beginning and the end of the screen saver, I have a full screen.
  but when my laptop started again I have this black border again.
  I have a satellite Pro 6100.

  Management information
  System
  Model = laptop
  Manufacturer = TOSHIBA
  Serial number = 0000000000
  UUID = ffffffff-ffff-ffff-ffff-ffffffffffff
  BIOS Version = Version 1.90

  OPERATING SYSTEM
  Caption = Microsoft Windows XP Professional
  Version = 5.1.2600 Service Pack 2

  CENTRAL PROCESSING UNIT
  Index = 1
  Manufacturer = GenuineIntel
  Name = Mobile Intel (r) Pentium (r) 4 - M CPU 1.70 GHz
  Version = model 2 Stepping 7
  Max clock speed = 1694
  Socket designation = uFC - PGA Socket

  Display
  Index = 1
  Horizontal resolution = 1024
  Vertical resolution = 768
  Chip Type =
  The RAM size =

  Very strange problem! Can you please tell us more about this problem? I assume that you have installed the OS on your own. Since when you noticed this weird display problem?

  Have you noticed this immediately after installing the OS (without driver)? Did you install the display driver on Toshiba support page?