Satellite Pro L300 - 27H: number invalid would be and model

Similar Questions

• My Satellite Pro A300 series number is not found and can not get the upgrade to Windows 7

  When I get my Satellite Pro serial number, it is said that it is not in the database and I can't go any following get Windows 7.

  Can anyone help?

  Hello

  What model of laptop do you have exactly?

  Which from Toshiba Web site did you use to upgrade to Windows 7?

  Are you sure of your laptop is supported and upgraded Windows 7 ready?

• Satellite Pro L300 (PSLB9A - 02L 001) - remove Vista and install Windows XP

  I'm waiting for delivery of a L300. I also bought XP I want to install XP as soon as I get the L300. The laptop comes with Vista installed which I never liked.

  I intended to create a Vista recovery disc just to make sure before you start the conversion.
  I was going to do the installation of XP reformat the disk and partition of the HD.
  I was also going to download all of the drivers XP for my model on the Toshiba site, the installation then the XP installation had finished.

  Is there anything I should be aware of, or have missed?

  Hello!

  I think you are right but before doing something I will give you a few words of advice:

  Before you do something on your laptop or begin to install Windows XP, you must create the Toshiba in Windows Vista recovery disk. I know that you n t like Vista but with these discs every time you can restore your laptop factory settings. Independent that you have installed on your laptop. You must start only to drive recovery and follow the instructions on the screen. The factory settings will be restored in a few minutes and you should not install additional drivers. The disc already contains all the drivers and tools of Toshiba and so you can save a lot of time! Also if you have problems with your laptop you can test with the settings to determine if it s a software or hardware problem. As you can see it of very useful and easy the recovery disc.

  According to installing XP you need a disc of Microsoft. You must format the HARD drive and you can then create the partitions you want. In your case, I'd a partition for the system and one for your data. The point is that if you need to reinstall Windows XP at a certain point you should not back up the data first because they are already stored on the second partition and to reinstall Windows XP, you need to format only the first partition. Of course, you can do what you want, but then I install Windows on my notebooks.

  Finally and above all drivers that you find on the Australian site of Toshiba, that of right. I think that it shouldn't be a problem to install it so just download all the and the tools of Toshiba. After that, the XP installation is complete and you can do what you want.
  In addition, if you have installed all the drivers and tools for XP you can make an image of your installation. For example with Acronis True Image. Therefore, you can restore your installation of XP every time and I think it can help you save time. I have good experiences with Acronis and I do a picture of my too custom installations.

  I hope this was helpful for you and if you have any other questions, please let us know.
  Have fun with your new notebook from Toshiba! :)

  Good bye

• Satellite Pro L300 series-player Dvd slow running and jumping

  Hello

  Having really annoying problems with the DVD player on my laptop. I watched a DVD long enough last night on this matter (about 5 hours!) and it was fine. Now today when I came to watch something else on this subject, it is slow really. It took about 10 minutes to start, and I continued to hear 3 beeps followed by slightly stronger than his usual purr! I just got to work, but now it keeps crashing the scenes and then crashed altogether. When he does not play, it is very bad as the audio works well, but the scenes are jumping around!

  Anyone have any ideas as to whats wrong here? Is - fixable? I only bought the laptop 2 months ago so enough that annoyed that something has gone wrong already!

  Michelle

  Hello

  This happens when you restart your laptop?
  This happens if you watch movies (original DVD movies) DVD only or if you look at another video file?

  Is this behavior for some certain movie or this problem occurs with all DVD movies?

  You know, it's not easy to say something concrete about it. It is important to see how it works and exactly what is happening. Try to do some tests with different audio/video media and display the results.

• 8 issues of the new owner of the Satellite Pro L300

  Hello to all forum users!

  I bought a new Toshiba, the Satellite Pro L300 laptop and have until January 14 to test - if it looks like it is not working properly I will return it to the store where I bought it.

  Here is a list of questions I have:

  1. whenever I turn on the laptop or it is suspension or hibernation mode, and when I disable it, the cd/dvd drive makes a clumsy mechanical noise.

  It seems to me like the cart that transports the laser and optics is running in a mechanical stop.

  Is this normal?

  2. There is a hot sub-pixel on the screen (in blue) and according to the Toshiba info in the box, this is normal and does not return.

  Should I worry about this?

  3. when I run the test memory at the start of the system, she says she'll start windows automatically at the end of the trial and show me the results of the test.

  It performs the test, Vista boot, but I see no reports of results.

  Where can I find the report?
  Is there a known issue with this test?

  4. the service program Toshiba to perform diagnostics of slot Vista does not work. Whenever I run the test (PCdiag.exe) I get an error message Vista saying a defect was found in the KERNEL32.dll module.

  Where can I get a fix for this?
  I have already installed the updated files on the Toshiba web site for the "Value Pack", which is where this utility, but still not the error message.

  5. I want access the settings of the bios at startup, but have not found a way to do it again.
  F2 gives me a menu for memory test or normal boot system.
  ESC is not me in bios Setup either.
  There is a utility for bios Toshiba that I can run Vista, and I see that any upgrade bios firmware should also be done through Vista.

  Is there a way to access bios at startup?

  6. I would like to run XP on this system and realized that this model (Pro L300 PSLB1E) is compatible XP, and I should be able to download all the drivers from Toshiba to run under XP.

  Does anyone do this?

  7. the laptop and configured Vista Basic when I did the first power on, but the license sticker on the bottom of the laptop has a product key for "Vista OEMAct Business." I was captivated by this laptop as the option to revert to XP Pro with Vista business. The box did not come with any CD or DVD and no manuals explaining how to install Vista Business.

  This is reason enough to return the laptop in the store where I bought it, which is a chore, I prefer to avoid if I can install Vista Business.

  Can someone help me understand what is happening here?

  8. is there a way to contact technical support by e-mail?

  Thanks in advance to anyone who can answer all of these questions!

  Hello

  Two weeks ago, I worked several days on friends Satellite Pro L300. Your questions are interesting and I will try to provide an answer or comment.

  1 this is normal behavior. I noticed it on other models of computer laptop too. Right now I use Satellite P200D and I noticed the same thing.

  2. of course, you may have noticed a dead on the screen pixel and more on what you can read on
  http://APS2.toshiba-tro.de/KB0/TSB5400ZD0002R01.htm
  http://APS2.toshiba-tro.de/KB0/FAQ8702EI0000R01.htm

  3. maybe follow links can help a better understanding:
  http://web1.Toshiba.ca/support/TechSupport/TSBs/all/-TSB001369.htm
  http://www.bleepingcomputer.com/tutorials/tutorial146.html

  4. what to say about this? I t has not noticed this error and I can recommend just reinstall full VAP. Remove preinstalled system, restart your computer and install the latest version of the Toshiba download page.

  5. When you start the laptop downstairs you can find info how to enter the BIOS settings. It usually takes F2. I really don't understand what is wrong in your case, but must work F2. Press immediately after turning on your laptop. Press several times. You have to work

  6. If you can find the download page of drivers, tools and utilities on Toshiba Windows XP Home edition, you should be able to install and configure Windows XP Home edition on this model of laptop. For the installation of Windows XP edition family please use Windows XP SP2 home edition.

  7. This must be clarified with your local dealer. The fact is that Toshiba doesn t offer any CD/DVD and recovery DVDs must be created by the owner of the laptop. I presume that you didn t seen or read Toshiba reminder about it. This point explains exactly what needs to be done.
  The recovery media can be created using the preinstalled Toshiba Recovery creator. The shortcut is placed on the desktop.

  8. I'm afraid, you must contact the hotline, but as far as I know Toshiba's toll-free hotline.
  Call and ask if there is something you want to know.

  Good luck!

• Satellite Pro L300: How to change the display settings

  Hi I have a toshiba satellite pro l300 run a pentium dual core and intel 965 display chip any games I play on my laptop, they open in a small box and not full screen I've had a quick glance at the settings to try to resolve this with no luck.

  Can someone tell me if there is a way to change the settings to get the games to play in full screen, my current display settings are 1280 x 800 pixels and running at 32-bit color.

  Any help would be appreciated.

  You should set this option to full screen in the games you play. Checked for these options, because you are given something like graphics, solution details and in most cases should be windowed.

  One thing you might try is to uninstall your current display drivers, and then reinstall new ones. Make sure that you use tools like ccleaner cleaning record or similar.
  Check if you have installed all the latest updates of windows and directx version, if you are using Windows XP.

• Satellite Pro L300 29V - hard drive is dead

  I have a Toshiba Satellite Pro L300-29V only about 2 months, and suddenly the hard drive (very full) is apparently dead.

  Initially the laptop starts Windows correctly, but now the HD is not yet recognized in the BIOS. If it goes beyond the Toshiba splash screen, I get the thing PXE saying "a cable is unplugged. I tried to re-allocation of places the reader twice, but still nothing.

  It's really disturbing, because I had transferred recently practically my whole LIFE on it on other computers which many many many hours of musical recordings that I can't really afford to lose.

  I think I'll have to buy a HD dock and see if I can read and copy the data.

  Does anyone else have this problem? It is likely that the drive could have been erased?

  I should also mention that a day or two before this happened, my girlfriend was using etc. Open Mobile (Internet Explorer, Microsoft Word,) - computer I pressed the power button that normally makes hibernate - and when I turned it back, rather than resume where he left off, the computer started from zero and no work/windows were saved.

  I'm afraid that might be some stupid day, Avira, or on the Windows updates without end that has damaged something...

  EDIT: OK, I have a picture of the error I received before complete failure, but I can't download it here. Here is the text (on a blue screen):

  -----
  A problem has been detected and Windows has shut down to prevent damage to your computer.

  If this is the first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow these steps:

  Check to make sure any new hardware or software is installed correctly.
  If it is a new installation, ask your hardware manufacturer or software, the windows updates, you might need.

  If problems continue, disable or remove any newly installed hardware or software. Disable the BIOS memory options such as implementing caching or shading. If you need to use safe Mote to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode.

  * Technical information: *.

  * STOP: 0 X 00008086 (0 X 00000000, 0 X 00000000, 0X00000000, 0X00000000) *.

  -----

  Post edited by: atomicnut

  Hi mate,

  First of all, I must say that I have this Satellite L300 too. But I didn t have no problem, the HARD drive works fine for 1.5 years and I use this laptop for Internet and emails everyday. I m very satisfied.

  However, what do you hear now?

  I hope that you can copy your data to another device and you will need a new HARD drive for your Satellite Pro L300. That's fact!
  In addition, there are a few good programs that they can the recovery of data from faulty hard drives. Just search with Google, you will find some interesting links.

  Good luck!

• Satellite Pro L300: DVD drive eject does not & recognizes not all disks

  Satellite Pro L300 dvd player eject does not and does not recognize the disc that sits in.

  Please help someone,

  Thank you very much.

  What kind of help do you expect?

  You mean he s a software problem?

  I doubt it because it sounds like a mechanical hardware problem and in this case, the disk must be replaced.

  The laptop seems to be is not very old, and I think that the guarantee must be valid
  How about you, communicating with ASP in your country and ask for a replacement WEIRD?

  I think this helps

• Satellite Pro L300 - TEMPO 2.0 rejects serial number

  Hello world

  I need help. I have a Satellite Pro L300 with Windows Vista Home Basic.
  A couple of days, I downloaded TEMPO 2.0. But this version rejects to confirm a serial number of the laptop.

  I don't know that I have insert the number correctly.
  On the http://aps2.toshiba-tro.de/unit-details-php page I can see information on my laptop so the serial number is correct.
  But on the sign-up page I can't fill the serial number as an interactive form refuses to consider.

  It is said .

  TEMPO previos version worked well.
  What can I do about this problem?

  Thank you.

  Hello

  Are you sure that you have not mixed a few letters, numbers?
  Maybe you have inserted a model instead of the serial number?
  Anyway. I have to wonder if it's really important for you to m
  I mean the laptop runs without problem and the Tempro would send you a notification if a new driver downloaded update was made.

  But to be honest I m do not use this tool more. I do not need to update the drivers always because the new update has been published. Of course I could do this if something would not hurt with my laptop, but given that my laptop is trying to ruin I put t run any updated driver (of course I update my OS still) without problem

• Satellite Pro L300 upgraded to Win8 but I would like to update the drivers

  I have upgraded to Windows 8, but I found the Wifi adapter needs to be reset frequently (it seems to be without a cause) - Troubleshooting Windows 8 solves it by resetting the adapter, but I thought there will be a fix for this?

  When I tried to update the drivers I found that the L300 is not (in the not extensible or expandable lists)-is the L300 compatible in this respect by another model? Or can you suggest how to update all the drivers of Toshiba for this model.

  Thank you

  Your Satellite Pro is the model of laptop old enough and not supported for Win8.
  It is difficult to find drivers for the notebook not supported models and old.

  Problem is that if you make the decision to do so anyway you are on your own and can be all just lucky if everything works properly.
  > is the L300 compatible in this respect by another model?
  It is not easy to give you the right answer. What needs to be done is to compare each hardware component important as chipset, GPU, chip sound, LAN/WLAN with other models and see if some Win8 drivers are available. It is not so easy.

  For example: Toshiba Satellite pro L300 offers 4 different hardware platforms. One you have? What is the model number of your machine?

• Problem with satellite Pro L300 Ethernet controller

  Hello

  I have a Satellite Pro L300 (PSLB9A - 02L 001). Have'nt after being on the dial for the year last I was wireless (it worked well before that) but am now back on broadband but I don't seem to have any wireless.
  Checked the Device Manager and there is a yellow exclamation next to the ethernet controller and it seems there is no pilot, but apart from that, there is no further details. I tried to update the driver but it cannot find the driver on my computer and it will not search the Internet for this.

  I tried, but none of the drivers I downloaded seems to work...
  At the back of the computer laptop is a sticker - PA3613U-1MPC, I think it's the wifi card that is missing the driver but I can't find a driver for it for the life of me...

  Any help would be wonderful.
  Daryl in New Zealand

  You are right. This part number is WLAN Card. I put t know what operating system you use but for download driver Atheros http://aps2.toshiba-tro.de/wlan/?page=downloads WLAN

  I hope this will help.

  What is now with LAN driver? Do you need it too?
  In any case, visit the Toshiba support page under http://www.mytoshiba.com.au/support/download and there you should find good LAN driver for your model of laptop.

  Send comments.

• Satellite Pro L300-1AF fails to start

  I have a Toshiba Satellite Pro L300-1AF that won't start, it stopped working a few weeks ago and I tried startup repair and things, and nothing seemed to work just kept loading a black screen with a cursor but nothing else. After a little more research, I found out how to restore to factory settings holding the 0 key etc. when I tried this he got 54% then the screen everything went black and now it used to boot. It happens with just:

  -Unable to start windows. a recent hardware or software change might be the cause.

  file:\Windows\system32\winload.exe
  status: 0xc000000e
  Info: the selected entry could not be loaded because the application is missing or damaged.

  He also says to insert your installation disc, but I have not one when I bought it.

  -What this means and how can I solve this problem? I tried the factory restore and just make it even worse.

  Any help or advice would be much appreciated

  Hello
  > He also says to insert your installation disc, but I have not one when I bought it.
  That's your first problem. This model laptop was delivered without disc recovery but the preinstalled software that allows you to create a recovery media. All this is clearly described in the document s user manuals.
  Now, your original Vista operating system has disappeared. On this path virtual I can't say with certainty what the problem is, but somehow, I think the HARD drive's troublemaker.

  What to do now? First you need the Windows installation for the installation of the OS disc. Original Vista may not be used more so my advice to you is to get the Win7 32 bit install disc and try to install it on your machine. Win7 is entirely compatible, so there is no problem to install all the necessary drivers, tools and utilities.

  By default the BIOS settings and try to install Win7. If the same problem recurs and Setup will stop I m afraid HARD drive is defective. If possible, try to get another HDD for testing purposes.

  You know you have to play a bit with your machine now and find out what the problem is.

• BSOD STOP 0 x 00008086 on Satellite Pro L300 - 1 K PSLB9E

  Hello

  My son came back from uni with his laptop which, to quote ' is knacked - no idea what the problem - been like that for weeks...» »

  At startup, it goes to the green bar of process, then goes off, then comes up with the BSOD - technical details: Stop:

  0 x 00008086 (0x00000000) (0x00000000) (0x00000000) (0x00000000)

  At this point, I didn't get any action with her, when I make a bad situation worse.

  The laptop is a Toshiba Satellite Pro L300 - 1 K (PSLB9E) running Windows Vista.
  (I would provide more information, if I could, but can't until I can start to check specifications)

  Thanks in advance.

  Hello

  BSOD can be caused by a hardware or software problem.
  First of all, you should check if it s not software related issue.
  In such cases, it of needed to reinstall the Windows operating system.
  Usually the new OS installed should not cause any BSOD!

  If the Toshiba Recovery disk does not help you, then you should start to investigate
  It may be a cause of modules defective memory BSOD issue very often.

  However, if you have no knowledge about computers, then you should ask a technician to downtown to control parts.

• Satellite Pro L300 - XP runs slowly

  Satellite Pro L300 PSLB9E - Windows XP
  Works slow intermittently, but shows inactive in the Task Manager. Disable anti virus etc, but always slowly works intermittently.

  Can anyone offer advice please?

  Hey mate,

  First I must say that it is really hard to say why your laptop is running slowly. There are several reasons for this problem, but it would be interesting to know if you have installed the operating system preinstalled by Toshiba or did you install XP yourself using a disc of Microsoft? In this case, you should try this again with the Toshiba recovery disc. It contains a picture of the factory settings and so, your laptop should work correctly.

  In addition, I would recommend to defragment the HARD disk, disable some services and startup programs that you don't need and you try a good antivirus like AntiVir. After that, clean you the registry with CCleaner.

  Good luck!

• Need driver SATA XP for Satellite Pro L300

  Hello

  I have a Satellite Pro L300 Vista.
  If I have problems of major incompatibility with Vista I can swap the readers so I want to set up a second hard drive running on XP Pro.

  When I try to set up the XP he sees not the SATA hard drive. I know that it's because XP does not contain the SATA drivers. Couple of questions

  (1) I saw a comment that recommendsto change the BIOS for SATA setting to "Compatibility" and this should work. I tried this but did not find it worked - everyone find it works?

  (2) where can I find the XP SATA driver? I crossed the XP drivers for Satellite Pro L300 Toshiba's web site, but could not see any SATA driver.

  Thank you

  Hello

  As to the question;

  (1) some notebook models containing this function in the BIOS and some don t BIOS that SATA option. If the BIOS has this option, you should be able to put AHCI Compatible mode. Then a SATA driver won't be necessary but also your SATA function would be disabled and HARD drive might work more slowly. So I recommend to set to AHCI, and then reinstall the SATA driver.

  (2) the SATA driver is part of the Intel Matrix Storage Manger. You can include the SATA drivers using nLite software. The necessary files of the SATA driver can be downloaded from Intel here page:
  [32-bit (201ko) floppy Configuration utility 8.6.0.1007 | http://downloadcenter.intel.com/download.aspx?url=/17061/eng/f6flpy3286.zip&DwnldId=17061&ProductID=2101&lang=e ng]