Satellite Pro L500-12F - problem with CD/DVD player and screen
I have a few questions on my laptop...
1. is it normal that the DVD rom on some DVD/CD it is very noisy and vibrates a lot, spesialy on older CD
2. the lid of my laptop when I close its kinda not in harmony with the rest of the pc it is not fully aligned, but it's a little difficult to see wait when you look for it... but its good on and what is not lost or anything just not setting for the "body" of the laptop
3. the cover still once, under the screen where the cover is mounted on the 'body' off the laptop so... It is not glued to the screen as the rest of the rolled edges it is right next to him that you can drag into it, so you can see the wires enter the screen etc.
is this normal?
(1) maybe your old CD's doesn't work correctly. What happens if you try the same disks in another computer?
Regarding your display/cover problem if you mean that you can see the cables that they go into the screen I can see it on my laptop. Normally, all the cables are invisible and under the plastic.
He s strange to say something on the subject but maybe a lid plastic isn't installed correctly or a screw is missing
If you think that something isn't normal, you should contact your authorized service provider. They can check the laptop.
When I put a DVD (game or film) in my DVD player, the computer tells me that the DVD is blank. He suggested me to burn the data above.
Could you tell me where that comes from and how to solve my problem?
Thanks in advance
If you use original music CD or DVD movies something like that shouldn't happen.
What media do you use? Original or some self burned stuff?
Satellite Pro L500 - 19 X running on windows 7.
The machine boots ok, then on the connection or the work of touchpad or keyboard screen.
The only way I can solve this problem is to go back to a previous restore point.
After that, the machine works fine until I power off, on the getting started once again, I have the same problem.
The machine has applied updates.
You can use two devices in safe mode or when you enter the BIOS settings?
If possible, run feature, installation and test of recovery HARD drive with the factory settings.
I know, it's a more radical method, but the best way to test the operation of the equipment.
HelloI have recently had problems with my DVD ROM read drive media correctly, when I put in a computer game (lets say Star Craft 2 as an example at random) Autorun makes me up some options and says it's an image and request either 1.) Open the files and view them, or 2.) See all photos in Windows and some other similar options.It will not recognize the game as a game and will not bring up the menu to install the game or whatever it is, sorta solve this problem I put the automatic run settings so that it opens files in the photo (since it is the software game image processing) and once he opens the folder I click on the installation program manually.I checked my driver to ensure that it is up-to-date.For any help or suggestion will be welcome.
SOLVED!I found out with a little research it was Vista blocks the autorun.inf files in games and keep them to read and run the .exe files automatically and so he held a photo, thank you for the help and suggestions.
This all started with Facebook - good blood... But now I have a huge problem with Adobe Flash Player. I followed the instructions to remove the program but now I am unable to reinstall. I disabled the Norton firewall, but any time, I try to go to download the latest version (and earlier versions) for a reason, it is impossible to connect to the download files. Can someone tell me other places I could try?
Or give me other suggestions.
Hi ag, here's a thread with instructions to uninstall it and install both IE & Firefox you can follow:
You get Post #32.
If you have any questions, please report before you start.
I just signed up on this forum because I hope you guys can help me with a really strange problem.
I recently bought a Satellite Pro C850-1MX
It came with Win8, but given that I don't really like Win8, I bought an additional Windows 7 Pro (64 bit) license and installed on the laptop.
The problem I describe, also arrived on 8 to win, which makes it even more strange.
As soon as I connect a cable to the RJ-45 port, Windows tells me, that the LAN connection is not connected.
As soon as I unplug the cable, Windows starts looking for a network and actually found one!
So, the only way to connect to my LAN cable is... I have activate the LAN connection, wait that it detects a network (without the cable connected!) and meanwhile to connect the cable to the network port.
Now... If I disconnect the cable once again, Windows still shows its connected.
I must say, that I am a Director of professional network for more than 10 years now, so I should know my systems, but this never happened to me before. Event log shows nothing, re-installing drivers did nothing either. IM quite confused here and I hope you guys can help me.
Thanks for reading, and let me know if you need any additional info!
Greetings from the Germany,
To be honest I confused m.
I would try to start talking about the drivers installed, since you changed the system for Win 7.
All the network devices, such as card WLan and LAN card are properly recognized in Device Manager?
As I m not wrong not the laptop was equipped with a network card Realtek-8111F (1000BASE-T/100Base-TX/10Base-T) and WLan RTL8723AE Realtek b/g/n card.
If both should appear in the device properly Manager if you have installed the drivers correctly.
> As soon as I unplug the cable, Windows starts looking for a network and actually found one!
Are you sure that you speak of LAN and WLAN?
For me it made no further since. If the network cable is unplugged, the notebook would connect to the WLan where WiFi is enabled.
I have problems to install the KB2887069 update.
It seems to install OK... prompt me to restart... when I do it, says it configures... GETS to 7%, then starts rebooting... watch it configures again... up to 7 or 9%... and then reports it is defect and restoring... restarts again... and it is quite... not installed and reference to Windows Update confirms it failed.
All the other updates I had installed today very well once I realised KB2887069 was the problem and failed to update.
I am running Win 7 Prof Serv Pack 1 64 - bit on a Toshiba Satellite Pro L850 1DR. I use my AV Microsoft Security Essentials software.
For now I had to hide the update... but all of the bright ideas how overcome the problem. I tried the Microsoft site, but there is still no answers who brought a solution for me.
Thanks in anticipation!
I googled around for KB2887069 update and it seems that you are not alone with this problem to Microsoft Update. I also found your request in the forum, Ms.
In other words, that's not a problem of mobile by this must be resolved by Microsoft.
I read in the MS forum on this issue and this issue is still under investigation.
I hope you can help me with the following problem:
I need to work a program that we OpenGL for drawing, but still the program does not work if it opens the drawings, the following information, always on the screen:
"OpenGLView: EnableRenderContext failed" and the stop-work program.
So I dry to update the driver grafik, but it does not work. I found a thread on this forum, but http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=67241 his looks.
I am at the part:
Thank you, useful, but still having problems. I downloaded "Intel® Chipset Device Software (INF Update Utility) v 22.214.171.1249" and installed it the way you say, but the computer says I'm already under the latest version of the driver, which the computer is 126.96.36.19922. I'm running Windows 7 x 64 Home Premium. I can't forget the old version and use the new version.
I don't really know the command SETUP-OVERALL, where I can find this command...
Please help me, I need the program to work!
Computer laptop-type: Satellite Pro C660 - 1J3 PSC0RE and I we Windows 7 Professional 64 bit
Thank you alex
PS Sorry for my English ;)
Post edited by: alexk
I think the drawing application needs the graphics driver that supports OpenGL.
To my knowledge, the driver of the Intel page should already contain the OpenGL.
The Satellite supports graphics Intel HD (Intel HM55) so I think that you should use the driver from the Intel page, even if the update utility indicates that you are using the latest driver.
I think that you need to uninstall the old driver through the Device Manager.
In addition, check whether it should be uninstalled in the control panel-> software.
Then download the latest driver for the Intel HM55 chipset, and install it via the Device Manager.
You do this by using the Advanced installation procedure that will force windows to select the driver from the driver's record, that you have downloaded from the Intel page.
I recently acquired a Satellite Pro A10 (PSA15E - 0115Q - EN) off the coast of the friend. It doesn't have a wireless card installed, but I managed to take of a Lucent MPC13A-20 that was installed without any problem, and it is recognized as a Toshiba Wireless LAN Mini PCI Card. However, despite the computer being able to read my neighbors wifi (next door and in the apartment on the floor), he refuses to acknowledge my router, even if I'm in the same room. My router is a ZyXEL P-660HW-T1 v2 which works very well (I tested it with another laptop).
Can someone please help!
Thanks in advance,
Make sure your router is using a WiFi standard that supports your card. If you use 802.11n you should drop down to 802.11 g for the tests.
In addition, you should check the channel of your wireless network card. It should be the same as the router.
I don't know when the problem first occurred. This morning, I tried to install a software scrapbook. The drive seems to be running... I can here fan start when I put the disc. I never had the installation to the program menu. I went to look for the dvd player do a manual install, but there was not a listed DVD player. O_o I tried to install a different program to have the same results... no DVD drive not recognized. After a more thorough review in computer Manager I see that there is a yellow! on the DVD RW AD - 7560 ATA Device. I also have this message under properties for the reader - Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39)
I need help with this problem.
Computer: Acer Extensa 4420
Operating system: Vista Edition Home Premium
Please try this first:
Hello world! I hope that someone out there will be able to help me with this problem.
I have a TOSHIBA EQUIUM L350D with a CARPET * A DVD-RAM UJ-850 s ATA Device like the CD/DVD drive. Recently, the small plastic disc that fits on the center pin and the handles of the CD or the DVD has started to come adrift when the drawer is closed and the rotation starts; It's a horrible grating noiise! The small plastic disc appears to push on the center pin and I tried pressing the home more firmly, but still, it breaks off at the speed.
So I want to know: is there a way to secure the disc plastic safe? And if not, the only solution is to replace the drive? I don't know how I got into all this.
Thank you very much in advance for your help!
I m quite skeptical that you will be able to solve this problem. Check on eBay if you can buy the new driver.
Replacement should not be that complicated, and it will be certainly simpler to solve this problem.
If you need assistance with replacing optical drive let us know.
I have a Dell Studio with Windows Vista installed as the operating system. The problem I've had since graduating from the computer, is that it will not read a single DVD and only a handful of CD. I tried every DVD I can get my hands on so I know that the DVD themselves are not the problem. Any light anyone could throw on this problem would be a great help. Thanks for your time.
Have you already gone through all the articles that I have posted and tried several different Mr. Fix - it notes in them? We cannot help you if you do not have our recommendations. If you are looking for an easy answer, it is not a. These are troubleshooting for this type of problem and perhaps only one of them will work (or maybe none of them will work) - but the only way to know is to try.
If you honestly went through all the procedures, I have listed and the problem persists, then I suggest that it is a hardware problem and you need to take it to a computer for the service repair shop as these options pretty well cover all the possibilities of the software.
I hope this helps.
Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.
I use Toshiba for a long time, this is my 3rd Toshiba laptop (I bought it in June 2010), today I bought the helmet, when I plugged it in, it did not work. (When I talk with my friend through sky, I use the laptop speaker instead) Then my friend got me to download a driver for the sound.
After the download, the helmet worked perfectly. BUT the speaker on the laptop did not work. Then I restarted computer again and this time when you turn on, it's stuck. stop boot on Toshiba logo later process, there are peep sound (not speaker, he is very strong), I can hear it from the inside. I can't do anything else, JUST close.
Please help or advise where can I take my laptop to the service because I think that if people reply to my post and I don't know if I can fix it myself.
I'm going overseas week next to the presentation and need to use the laptop. Do you think that if I take the laptop to the center of toshiba, they immediately understand problems? I am now using my old toshiba, and it is slow to make any presentation.
You use normal headphones with headphone jack or USB?
Headsets with headphones are usually easier handling in my opinion.
In any case, at the time where your computer laptop doesn't boot and stuck on Toshiba logo, right?
In this case, you must remove the battery and the AC adapter at a time and test it again.
Check this box!
I have a Dell 8400 and have been looking how to subscribe my DVD and cannot find a way to do it... anyone would be able to give me some advice? Thanks in advance.
Thanks for all your answers, there is a disc in it... I had a paper clip and found the small hole under neath the reader and edjected it as it and it works... the trombone is a tool right...
and I tried edjecting it about 2 years ago
I'm a casual pc user, so it's not very technical!
I bought a new computer from Dell Studio One desktop in July. I use it once or twice a day in general. When I use it, I usually insert a flash drive so that I can save my documents, etc. I also use the safely remove hardware option before removing the flash.
Here's the problem: these days, the little 'remove hardware safely' remained in my taskbar with the green check mark on that. When I click on it, it shows an option to safely remove drive F. Until this problem, when I want to insert flash, Windows would label it drive F. Now, all of a sudden, when I insert the flash, it becomes the G. And I have this ghost f.
It's not a huge deal, I don't know, but I do not understand what has happened. Furthermore, I use Vista, and when finally, I guessed my way, I found the Code 47 as the cause of the problem. Of course, Code 47 indicates that I left something trendy, but obviously, I have not.
Any help out there?
I suggest check in disk for the driver letters which are present management and remove no matter what additional driver letter (e.g. f :/) and check if the problem is resolved.) Follow the steps mentioned in the article below.
Change, add, or remove a drive letter
Thanks and regards.
Microsoft Answers Support Engineer.
Visit our Microsoft answers feedback Forum and let us know what you think.
Maybe you are looking for
Just got my H10 Camelio brand new and all fine except that the CD is duff. Have been Googling for an hour find where d/l the software and the user manual but without success. Someone at - it a link? Thank you.
I see that I have three primary partitions already made on this new L500 ~.1.) 2GiB/dev/hda1 to Toshiba Recovery,.2.) 330 + giB (C :) for Vista and 3.) 12GiB/dev/hda3?. I need windows dualboot both valuation and partition for Linux and the storage in
Hello.I want to place a new Image in the same place, but when I select the new Image it will jump to another post.the PDF is the same... Thanks for the help
I am building a fluid grid using DW CC page.The image is what it looks like in preview. Pretty much what I want.But the link below, this is what happens when I upload to the site.http://www.erniesbikeshop.com/index_new.htmlWhat I am doing wrong? thou
I was wondering if there is a tutorial on how to make a blog page to muse? Any help will be appreciated.