Satellite Pro M30: automatically turn off touchpad when I plug a mouse

Similar Questions

• My Satellite Pro M70 itself turns off in the middle of the secuence of startup

  My Satellite Pro M70 itself turns off in the middle of the secuence of startup

  After turning on if it passes the test post and enters the menu grub (Linux + Windows) or BIOS
  without problems, but most of the time after the start of the BONE found in the start - up, suddenly it powers off the power.

  The problem becomes bigger and bigger as punishment I can boot any operating system

  As seen on messages more soon as I cleaned the vents of CPU with a spray suddenly sure I wasn't a problem of overheatting.

  Someone has an idea of what can happen?

  Thank you

  Hmm, the laptop passes the MESSAGE correctly and it stops during the initialization of the operating system. Is this good?

  Well, in this case I would exclude the RAM to malfunction.

  I put t also think that it's an overheating problem because the laptop should work a little longer until it would be closed due to high temperature.

  What about the HARD drive malfunction? Are you sure that the HARD drive is ok?

  In my opinion, you should check the HDD and maybe try another.

  Welcome them

• Satellite Pro A10 just turned off with warning message

  Hello

  I have a Satellite Pro A10 I've had for about 2 years now. During the 2 ~ 3 days I started to have a problem very serious and boring, and you're doing something to run MS word thro to play to a very high technical game (this game can be played on an old 486 no probs) the laptop after about 20 minutes (may vary) usage turns off just with warning message it immediately restarts without any problems and then after different durations down again and again :, (. everything got a clue what the hell happens, please help. :))

  Colin B

  Hello Colin

  Portable described behavior is specific to the overheating of the material. If the laptop is not properly cooled the temperature of the material at the level critical and just turns off without warning.

  Solution is cleaning. The device must be cleaned and dust should be removed. After doing this unit can take a new breath and you won't have this problem again. You will see that run cooling fan will also soften than before.

  Good bye

• Satellite Pro 6100 himself turn off

  Hello

  I'm from the Italy. It is 3 days that my Satellite Pro 6100 after some time (it can be 30 minutes or 3 hours) close itself.
  I tried to update bios version 1.70 to 1.90 without any result. I tested my HARD drive and it works fine. I formatted and reinstalled Windows XP Home SP2 Pro edition but the problem that it is still there.
  When it crash, reboot, it seems 'BAD RTC BATTERY' and "BAD CMOS", I have to press F1, then I exit without changing anything.

  I saw that 3 weeks ago appears at the beginning of this message: "PXE - E61 MEDIA TEST FAILURE CHECK CABLE"and"PXE - MOF OUTGOING INTEL PXE ROM" but works laptop well until 2 days ago.

  I don't know why, but every time I restart now stop when WINDOWS XP is on the window (not the first logo on page WXP black) cyan, but the second on the window cyan; can do work that I have to press CTRL + ALT + CANCELLED and it go to the desktop.

  I don't know what to do? Center of Toshiba, it is far from my town, if you can help me will be appreciated.

  Sorry for my English, I read a few post but exactly with my problems, there is no job.
  Thanks in advance, it's a great laptop I jump to save it.

  p.s. There is no dust on it, I tried to lift the keyboard to clean, but it was already clean, even behind the fan.

  Hello supertraz,

  On 6100 laptop there is a soft spot between the control panel and from the motherboard, causing this malfunction. You will not be able to solve this problem simply raise your keyboard and blowing air into your laptop.

  A good description on this problem (I had, too) can be found on this forum posted by user seintaxx here:
  http://www.eXpansys.com/ft.aspx?i=104221&thread=7

  A photo of the defaulting party is here:
  http://img204.imageshack.us/img204/3/sp6100fixby1.jpg

  Good luck with it.

  Kind regards
  chain

• Satellite Pro 4600 PS460E turns off in 3-4 minutes after the connection

  My Toshiba laptop is having problem that it turned off after 3-4 minutes of connection.

  He doesn't get turned off when we run it in safe mode.
  Pls let me know how to troubleshooting this problem.

  Hello

  Can you please tell us which model of laptop you have exactly? This laptop model older or newer?

• Satellite Pro 6000 display turns off sometimes

  Hello

  I hope someone can shed some light on a problem with a laptop Toshiba Satellite Pro 6000 that I can't seem to get to the bottom.

  The laptop has Windows XP Professional installed and works fine, except for the fact that intermittently (could be 5 minutes, maybe 90 minutes) the display screen is what I can only describe as 'blocks '.

  The o/s plant (I ran BACK and Tests of diagnosis when the problem occurred) I would say movement of waves of mouse to the screen and activity HARD drive software continues running, except the screen is unreadable with blocks of color scheme.

  Any ideas or suggestions as to what this could be, and how I could go about repairing it?

  Hello

  It's very strange question.
  Have you tried to update the graphics driver? If not then please select this option.

  Besides if the update doesn't fix this eventually it there something wrong with the hardware. In this case, it is not easy to say what could be wrong.
  In your case, I recommend you connect the external monitor if the problem occurs.
  If the color blocks will also appear on the external monitor so eventually the graphics card or motherboard is corrupt.

  But, if the problem occurs only on the internal laptop display, so I would say that there is something wrong with the display or the FL-inverter.
  In this case, you should contact the technicians to solve this problem, because guys have more experience than each common user like me and you.

  Good luck

• Satellite Pro M30 is suddenly off - flashing LED orange

  Hello

  suddenly, my cell phone is turned off. He wasn't on battery, not on the DC - cable.Now, I can't turn it on and the DC adapter does not help, it is not recognized. The 400 p LED flashes orange 8 times in the following code: long-short-short-short-long-long-long-short.

  Which means, that I am I supposed to do now?
  Can I use another DC-cable from any other laptop to check if it works then? Or it will cause more trouble?

  Thanks for the help!

  Jana, Germany

  HI Jana,

  Code orange flashing is an indication of error which can be diagnosed by an authorized Service partner. It usually indicates an error (hardware) in a component in your laptop. I do not think that you will be able to fix it yourself, but you can try a few things like the re-allocation of places the HDD, RAM etc modules.

  Good luck

• Satellite Pro A300 - the cursor moves continuously when connected an external mouse

  Hello

  I have a Satellite Pro A300. When I connect a mouse directly by USB the cursor moves constantly. I also have a mouse attached via a docking station, Toshiba and that works perfectly.

  It doesn't matter what USB port I use or if the laptop is connected to the docking station or not, or if it works on AC or on battery power.

  I thought it was the mouse that was the problem, so I went and bought a new one but the problem persists.

  Actually, while I wrote this post, he has stopped doing that and then started! Very frustrating.

  Can anyone help?

  Thank you

  Susib

  Hello

  How about, the touchpad is the slider moves and jumps using the touchpad?
  Try to disable the touchpad while using the USB mouse control if you can notice a difference

  What about BIOS?
  You have the latest version installed?
  Check it!

• Windows 7 does not turn off wireless, when I plug in the LAN. No priority of LAN to insert.

  My HP desktop computer: when I connect my LAN cable, the wiresless lights yet.  I have to uncheck - unplug my wireless (wifi), and then LAN takes over.

  But it's temporary. Turn off / on the computer again, my wireless is on (a priority) although I still have the network cable is connected.  Whenever I use my PC I must stop first of wifi wireless (left click on a small scale for turn-off). How can I get LAN priority in Windows 7?

  Hello Charles,

  It seems that there is a problem with the setting of control cards and links in your computer, you can follow these steps hope it will fix it...
  Start-> Run-> ncpa.cpl - entry
  Press-> alt + n + S--> click on the cards and links-> click on LAN and click on move previous button-> OK.
  Concerning
  Sanjay

• Satellite Pro M30: Computer does not enter standby mode

  Hi all

  I have a Satellite Pro M30...

  When my computer is in stand-by or is closed, the first keeps flashing orange led and it refuses to start. It reboots only when I unplug the connection and remove and replace the battery several times...

  Anyone knows what is the cause of this and what is the long-term solution?

  Longesson...

  Hello

  As far as I know the light glow orange or flashes while the battery is charging. If it of impossible to turn on the device while the battery is charging so in my opinion, there is something wrong with the electronic power to your laptop.
  You should contact the service partner for help.

  Good bye

• Satellite Pro U400-11V - charges only battery when the computer is turned off

  Following a reformatting my hard drive of the computer, my laptop recognizes only the AC/DC power adapter when it is turned off. When the computer is turned on, it does not recognize the AC adapter.

  Changed the power supply ac and it made no difference.

  Have also tried an update of the BIOS (3.0), I am running Windows Vista 32 bit.

  Hello

  I doubt it has something to do with the software or the operating system. In my opinion, that this looks like a hardware problem, because the battery will be always charged if AC/DC adapter is plugged in. That's why it of not necessary to enable this setting in the configuration of the software.

  If your BIOS is already updated, contact an authorized service provider. Technicians can check your laptop and maybe the motherboard needs to be replaced.

• Satellite A660 - optical driver turns off when burning DVD

  I have a problem with the optical drive of energy saving options that disables the drive while burning.

  I tried all the suggestions mentioned here [http://forums.toshiba.com/t5/Satellite-Laptops-A-Series/Optical-drive-automatically-turns-off-due-to-power-saver/td-p/223654], but it does not help.

  I start at the burn in Ashampoo Burning Studio free, and he seems to be good until the end. When it starts the process of lead-out the popup of the optical signals Drive Power drive is turned off. It's funny because it is still running at the speed of combustion and it will not stop. The reader becomes unresponsive, even I can't the DVD out. Even, that it disappears from the list of devices.

  The only way I thought so far to stop the car and release the DVD is in the shutdown/Hibernate the computer.

  Once the dive starts working again the STRANGE Fn-tab functionality started working and I can turn it on/Off/ejection at will.

  All the burned DVD - s are not valid, and so far I have not managed to burn a single functional DVD.

  I have a Toshiba Satellite A660 - PSAW3E with Win7 Enterprise 64-bit.

  Is there a way to fix this? Remove the optical drive power management?

  Hello

  To be honest I have never heard of this issue, but it appears that the optical drive power management is part of the power of Toshiba configuration utility.
  Part of the Toshiba value added package configuration done Toshiba power utility.

  What you can try, for testing purposes, to remove the Toshiba added value of the system package, restart your computer and try to burn DVDs again to see if the same problem will occur again.

  Toshiba value added package contains several tools such as utility cards flash FN so after his withdrawal, you will not be able to use the FN keys. In any case, after that trial, you can download and install Toshiba value added package again.

  I mean, I know what kind of conflict is there, but maybe you should consider it.

• Satellite Pro M30 graphics works not when the driver is installed

  Hi all

  I m having problems with my nvidia Geforce FX Go5200, in a portable Satellite Pro M30, (processor Intel Pentium M 1.7 GHz, 512 MB Ram). This card was working fine suddenly the laptop stops.

  I formatted the laptop and installed Win XP PRO. After installing the driver VGA, I restarted the laptop, but black screen started to come right after the Win XP splash screen appears. The laptop continues to start up but no screen.

  It starts fine in safe mode. I get my best screen simply by disabling the geforce card or uninstall the driver. I tried to install a new driver for the VGA on the download from Toshiba site, but same problem appears. I also tried the BIOS update but nothing happens.

  Can someone help me?
  [email protected]

  It's very strange question. It will be really interesting to know if this happens when you use the CD delivered recovery facilities.

  In any case, I assume that there is a problem with the LCD display. In safe mode, the desktop appears in the resolution decreases but the resolution to the OS boot will be suitable for a standard (1280 x 800), and of course, there is the problem.

  I am not a technician, but I recommend you contact the Service partner. AFAIK they use special tools and programs for display tests. They can tell you more.

• Satellite Pro M30 - NVIDIA graphics controller problem

  Hello everyone

  I have a Toshiba Satellite Pro M30 with a Nvidia GeForce FX graphics controller. ([Image of the motherboard | http://i258.photobucket.com/albums/hh242/hardousss/PC3.jpg])

  My problem is when I turn on the PC and wait a few seconds red and white vertical stripes begins to appear on the LCD and it cannot go after the BIOS password screen. I can type the BIOS password but when I hit OK or button that ENTER the laptop freezes. ([See image 2 | http://i258.photobucket.com/albums/hh242/hardousss/PC2.jpg])

  In very rare occasions where the laptop was turned off for a long time, I listen to him on and he could overcome the BIOS password screen but freezes after a while: ([see Image 3 | http://i258.photobucket.com/albums/hh242/hardousss/PC1.jpg])

  I plugged it to an external monitor and nothing has changed.
  I removed the inverter (responsible for the lightning of the LCD screen) and the problem is still there.

  Always to blame the graphics chip from NVIDIA.
  I read here that it is not possible to replace them because they are soldered to the motherboard. But I want to, where can I get a laptop NVIDIA graphics chip. They sell somewhere?
  I have a friend who works in an electronics manufacturing company (SAGEM) and told me that they have the tools needed to replace any piece on any Board of Directors.

  Thanks in advance for any help.

  Hello, my friend

  I agree with you. It must be a faulty graphics card. I put t believe you can buy a graphics chip separately but you can buy mainboard used laptop on eBay. In my view, Exchange Board is no problem for you.

• Satellite Pro m30: battery saver screen

  I have a satellite pro m30. with a Geforce x Go5200

  When I turn my laptop on its obscurity. I aways use power outlet. never just battery. I have to go in the setting every time I turn on. is the way to save all the settings

  Hi Dennis,

  Using the Toshiba power management or standard options of Microsoft?

  I would recommend the Toshiba utility, as this will allow you to set various options, including the brightness of the display.

  You should be able to set options for power supply and power of the battery of your choice, then save them so that they will be called automatically when you start your laptop.

  Power options are available from the control panel.

  HTH