Satellite T100-107 - after update driver, I can't use Bluetooth

Similar Questions

• Satellite M100 - Done INTEL new driver gma945 - can I use it?

  INTEL's new driver gma945, but where the of does on Toshiba driver download, I have only updates ATI, so I'M in TROUBLE IF I INSTALL the updated page INTEL DRIVER?

  Hello

  As far as I know, Toshiba offers drivers just tested and also used in the recovery image. Which laptop model you have?

  I can't say for sure, but I do not think that you will have problems after installing the new driver.

• Satellite 2430-402: which HARD drive I can use for an upgrade

  Hello

  I have a 2430-402 satellite and the hard drive is full. Can someone tell me the greatest, he will take care and what kind do I buy? (Probably not PATA or SATA but I should look into IDE)

  Thank you

  Jez

  Hello

  You are right. To my knowledge, the Satellite 2430 was delivered with an improved interface to drive HARD IDE (ATA-5). Therefore, we must look for IDE hard disks.

  I'm not sure about Mr. size of HARD drive max. I think that Toshiba provides official information what size HARD drive max can be used. I presume to test

  Laptop has been delivered with a40GB HARD disk. Am I wrong?
  Hmm in my opinion the 60GB HDD should run. You might also try a 80 GB HARD drive if it s compatible.
  But I really very skeptical about larger sizes.

  Best regards

• Since El Capitan update that I can't use my secondary monitor as a full screen preview on the first and after the effect CC 2015

  Since El Capitan update that I can't use my secondary monitor as a full screen preview on the first and after the effect CC 2015

  I also have this problem. I was told that it is a bug, they work.

• How can I use bluetooth on my Satellite C850-B906

  Please help me. How can I use bluetooth on my Satellite C850-B906. I can't find on the bottom of the search, and even in the PC device, bluetooth is not there. This laptop has bluetooth according to its specifications. (Bluetooth / WiFi (802.11B/G/N).)

  Good response will be highly appreciated.

  Thanks in advance!

  Hello

  I m not sure but I think you've got your laptop computer without an operating system preinstalled.
  The question is: which OS you have installed and that you have installed all the drivers needed, including BT (Toshiba BT stack) software?

• Satellite A100 - 192 (PSAA9E) FN + F8 key does not work after update driver BT

  I have just download the update of "blt-mon-20071009150856" Bluetooth driver and install the driver "BtMon2Inst_v212" on my A100 - 192 (PSAA9E). After installing the driver 'Toshiba Bluetooth 4' BT works very well.

  BUT I can't use wireless (FN + F8) key to switch between Bluetooth and the wireless device. I can disable/enable them from the control panel or the utility ConfigFree.

  No idea how to bring back the FN key?

  TNX.

  Hello

  I assume the ordinary models don t work properly.
  You must download this tool from Toshiba page and reinstall it on the XP operating system running.

  Please report if the common modules tool has solved this problem!

  Best regards

• Satellite Pro A100 - cannot update driver ATI

  Hello!

  I have a problem with my graphics ATI Mobility Radeon x 1600 card card. I can't update to the latest driver from the ATI. The program says that it can not install on my system - contact company for the most recent driver. But the one that is provided by Toshiba is almost two years!
  It all started with, that I could not run FIFA 2009... even if it clearly States in EA own manual that this graphics card is supported! But I do not see everything in the game - except the players. Only their shadows are visible...

  I know it's a lot, but I'm pulling the hair here!

  HEEELP!

  BTW: my system: Toshiba Satellite Pro A100-PSAACE - Core2Duo 2.0 GHz, 3 GB RAM, 120 GB of HARD drive Windows XP Pro.

  I really wonder that many people do not understand why the laptop manufacturers don't offer drivers for graphics cards so often.
  Each laptop manufacturer deals with design, hardware components and drivers used for the operation of the equipment. On laptops, hardware components are miniaturized and placed close to each other. This means that the heat and is a common problem for the designers of the laptop.

  Each computer laptop (hardware, drivers, BIOS, cooling system) is designed to operate in optimal conditions. If you want the new driver that can force a graphics card to run on the maximum limit, the result will be more heat. More heat means more risk for damaging hardware and overheating.

  So to laptops, there are limits that must and should be respected. Graphics card manufacturers cannot just offer new drivers for laptops and be responsible for the damage. When some owner of the laptop is damage graphics card because of the driver who should be responsible? ATI or Toshiba?

  For this reason, graphics card manufacturers say clearly: If you want the new driver laptop computer contact the manufacturer. Manufacturers must also protect the customer s of material and be careful with this stuff.

  So I think you see how it works and the display driver update will be probably endless discussion on each laptop computers forum.

  Good luck!

• Laptop HP 15-af122no: crash at startup after update driver AMD

  I bought my computer on February 2016, so it is quite new. There are 10 Windows ready and recently it has been upgraded. My internet connection LAN, no problems with that.

  Yesterday an automatic detection of AMD system informed me that my drivers need to be modernised and I gave her permission to upgrade, maybe that has been my biggest fault... After that I needed to restart the system, and I did. The computer started showing strange texts on the screen, I remember that one word from him, it was at the end of the first line: "watchdog". After that the text of HP showed and freezes on the screen. I tried to start the second time, the result was the same. Third time the texts initially showed no more, but the start crashed on HP display.

  I am now on a computer it's not me and I tried to get help for this problem to the Support HP Finland, since I can't use HP Support Assistant on my HP. I found a few tips I've tried:

  -J' removed the battery and the power cord, but it did not help

  -After starting the computer, I pressed ESC several times to get in safe mode. Finally I got to a mode where I could enter a few commands (unfortunately I do not remember more..), but it does not give me the result I was expecting (and said what page of support must be the result). The computer said that it does not find these batch files requested.

  I'm really sad that I have had no money to buy a proper memory stick or cd to make the stick recovery or discs... NOW, they may be needed.

  I've been thinking about resetting the computer, but there could be some risk, too... Please, please, help me, I don't know what to do anymore. I hope you find a solution to solve this problem, thank you already!

  Hi there @Troublefinder,

  Thank you for joining the Forums HP's Support and welcome! You have just a great place to ask questions, find solutions and get help from others in the community. I understand that once you had done a update driver and recently upgraded to level to Windows 10, now your HP for laptop - 15-af122no (ENERGY STAR) is not allowing you to start correctly.

  Please note , remove all USB devices. Disconnect all devices of non-essential, as these can cause some problems.

  Are you blocking upward at the HP Logo?

  Have you tried a hard reset?

  Have you tried to Test for hardware failures?

  Are - that you receive error messages or error codes?

  You happen to see a blue screen to choose an Option at all?

  If the computer hangs at the HP logo screen, try to clean the vents from the computer to the air and then restarting the laptop.

  Follow these steps to remove and reinsert the memory modules for troubleshooting:

• Satellite L300 - dead after update BIOS!

  Hello!
  I had a problem with Windows XP, so I decided to update the BIOS. After update, I got 3 lines of errors. After the reboot, nothing appears on the scree! I have toke off the power to the battery and the power cable for some time, I had taken only one cable, but still nothing! No beeps, some noise of hard/dvd disc on begging. Can someone advise?

  Thanks in advance!

  Thom

  Hey Buddy,

  It seems that the BIOS is damaged and it must be reflashed to an authorized service provider. This is a delicate procedure so these tools can t be downloaded and are only available for the FSA. On the Toshiba site, you can find a list of all FSA. Simply contact the closest in the country and ask for help. Guys will help you best possible
  However, this forum can help you:
  www.theeldergeek.com/forum/index.php?showtopic=21209

• HP Color Laser Jet Pro M452dw: no automatic duplexing after update driver

  Installed the updated driver and software M452dw.  I can't print any documents usng the automatic duplex function.  I changed the printer properties from one side of 2 sides, but the feature screen always manual duplex printing.  I have been using automatic duplex printing since I bought the printer in November 2015.  Something must have gone wrong with the update or it does not update correctly.  Suggestions are welcome and/or corrective action to fix the configuration.

  You will need to go to devices and printers and right click on the printer icon and scroll first and left click Properties. Now at the top of the page click on device settings and then scroll down to the duplex of change not installed and installable options at installed and apply and save the settings and it should now work as you wish.

• Satellite L50-B-177 - after upgrading the BIOS can not use the Polish symbols

  Hi, I'm newbie here. This is my first post, so sorry for the plain text.

  I have a problem with the laptop Satellite L50-B-177 1 month of my wife. After update BIOS (from Toshiba Service Station) to version 1.70 I have this problem: it is impossible to use symbols of Polish that comes with ALT + z, ALT + x, ALT + c. other - ALT + a - works normally.

  Problem is the operating system independent (even on the live session of Ubuntu). I understand that this is a specific problem for the location of the Poles, but causes cell useless for my wife (she is a teacher and write a lot of text). As much as I know BIOS downgrade is not available for customers, and the weeks of waiting for the new package of BIOS is out of the question.

  Any suggestions will be appreciated.

  Hello

  This problem occurred imadiately after updating the BIOS?

  Have you tried to set the BIOS settings by default once the update is complete?
  If this isn't it.

  Also, check if the Polish keyboard language was chosen correctly and as a default value.

  Comments are greatly appreciated.

• What HARD drive max can I use satellite 3000 514

  Hey all,.

  What is usable by the 3000-514 maximum capacity hard drive. It comes standard with 20 GB but I can't find anything online that gives this information.

  Kind regards
  Samurai Sjakkie

  Hello

  I m not 100% sure but to my knowledge the BIOS of Satellite 3000 supports a limitation of the HARD drive and you can only use the IDE 2.5 ", 9.5 mm HDD s up to 30 GB.
  Seems that BIOS will not recognize large s 30 GB HARD drive!

  I found this info somewhere in the internet. But you know the guy. These are only suggestions. If you wish, you can try any other disk HARD s i.e. 40 or 60 GB. It would be interesting to know if the HARD disk is running or not. Are you referring to the merchant of HARD drive if it of possible to test some HARD drive sizes!

  If you have more information, please report it here! Thank you ;) see you later

• Satellite A50 432: after reinstalling Windows I can't do its job properly

  I have a problem with the laptop A50-432 of unknown source without recovery CD when Windows XP has been reinstalled and after re-installation, I can no longer do its job properly.

  I have installed sound drivers SigmaTel C-Major Audio-sa50-xp - 614013835.zip:

  27/05/04, its pilot, Sigma, Windows XP, 6.14.01.3835, World Wide

  and what I get is noise from great height and whistle of the right speaker only. If I set an audio file for playback I can rarely hear good audio clean for a second or less and then he returned to his noises and whistles. If I connect the headphones to use instead of the speakers, the effect is the same.

  I followed the installation order and then reinstalled the drivers several times with no luck for his work. Audio worked fine before reinstalling Windows. I have no problem with the rest of the component and I also tried to disable the other drivers (for LAN, IEEE 1394, 802.11, etc.) without effect.

  Does anyone have ideas how I can fix this problem?

  Thank you

  Roman salute

  This problem occurs when you use the headset?

• Satellite L670-DX1 - after the installation of SP1 cannot use the memory card reader

  Hello

  Since I upgraded my Satellite L670-DX1 of Win7 64 bit to Win7 64-bit SP1 (2 days ago) I can't use my memory card reader, he always says it is a bad card and I should reformat the card with any card.

  Does anyone have a similar problem or better yet a solution for me?

  Greetings

  You have installed SP1 using Windows update option?
  Have you tried to roll back the OS to an earlier time to see if the card reader is working properly again?

  Have you tried reinstalling the driver of the card reader?

• Equium - after installing Windows, I can't use the touchpad

  I think the TouchPad should work after Windows instalation. I can't use TouchPad although I 'Synaptics' mounting in versions: 9.1.14.0 and 14.0.3.

  Vista show me the message when I install the driver (thws-20070919162134): "bad serial number" so that's the reason. If it wants to tell Windows activation number - it's OK.

  Hello

  What satellite notebook do you have?

  You have installed Windows using the Toshiba Recovery disk? Normally, if you use this disk you have the same condition that you have started the laptop, the first time (factory settings). This means that everything should work fine on your laptop.

  Normally the touchpad can be enabled or disabled by pressing FN + F9. Check this box!

  Welcome them