Scratchy Audio sound market?

Similar Questions

• Scratchy Audio

  I just reinstalled XP and now I have sound scratchy.  I had this problem once before, but I'm getting old and senile and forgot the solution.  I don't know that I had to go to a window and drag a bar at a lower level.

  Well, I just thought of it.  East went to the Panel of configuration/sounds, Audio tab and tab performance and reduced the hardware acceleration.

  I KNEW it was there.  Perhaps others with scratchy audio must check this setting.

• Satellite L755 - 1 1 PSK2YE - problem audio / sound

  Hi all

  I have a toshiba satellite L755 1 1 PSK2YE and same time he has a problem with audio - sound.

  The sound is ok for 3-5 minute after it shut down, after the resumption of 3-5 minutes, after 2-3 minutes.

  I have install all drive and OS (WINDOWS 7 and 10), but the problem is not solved.

  If I go to devices reading see attached Picture1 passing of the playback to the recording tab with a simple click of the mouse audio released a 10-30 seconds.

  reading tab mutual registration to RESUME audio playback devices

  can help me please.

  I have Toshiba L755-1 MB, PSK30E-04U006Y4... with Conexant Smartaudio HD, same audio problem. Its just cut randomly and turns back the same way as everyone else.

  I can turn it back on for a few minutes even if I go to sound options and just spent reading in recording tab without changing anything. I also tried everything from the pilot replacement windows 7 Ultimate update disable all improvements etc. everything works for a short time and that his cut back again.

  I like someone finally would come up with a solution for this big problem thanks to you all! I found MANY people having this piece of the issue there was no jet solutions.

  Here are two pages about this

  http://forums.Toshiba.com/T5/audio-S...on/TD-p/332616
  http://forums.Toshiba.com/T5/audio-S.../597884#M13125

  I tried everything nothing works, so please if anyone knows it please tell us magical solution.

  THANKS TO YOU ALL!

• Audio/Sound Driver for Compaq Presario C700 CTO Notebook PC

  I use WindowXP Professional SP2. After the new formatting of the partition, there is no set up to complete driver for Audio/Sound. What should I do?

  Please make sure that MS - UAA has been installed correctly

  How?

  Go into the system so devices Device Manager MS UAA installed correctly.
  There should be a list of Bus Microsoft UAA for High Definition Audio driver.
  If not, you should have a PCI card with yellow!

  Right click it and update driver,
  Not to connect, not to search and last install automatically.

  Use the driver below and if it does not try to force install it

  Conexant High Definition SmartAudio 221 drivers (ModelC700, Vx5xx series and dvx5xx and ABOVE )

  Pilot modded by money here
  Unzip it to a folder... Use the device, right click "Audio Device on HD" Manager, choose Update driver,
  Not to connect, install from a list or specific location,
  Select don't search, I will choose the driver to install.
  For the hardware Type select 'show all devices '.
  Remove control "Show compatible hardware" and click on 'disk '.
  Next... Navigate to the unzipped folder and choose the "WiSVHe5.inf".
  Ignore XP when he complains, Reboot.

• AUDIO & SOUND

  Hai accidentally, I uninstalled my audio & sound on my pc, can I know how to install their return.

  Just go to the HP, pilot and support section website, what kind of HP you have?

• Slow, scratchy audio. Where can I get hp pavilion audio drivers?

  my hp pavilion model # zv 5202 has a problem with either the default audio codec, the driver or the configuration. after fresh installed xppro, a still slow, scratchy audio. SoundMAX appears to be default, tried to use AC97 WITHOUT RESULT. SAME RESULTS... no idea what is the correct codec, pilot and / or software? or any other possible remedies?

  my hp pavilion model # zv 5202 has a problem with either the default audio codec, the driver or the configuration. after fresh installed xppro, a still slow, scratchy audio. SoundMAX appears to be default, tried to use AC97 WITHOUT RESULT. SAME RESULTS... no idea what is the correct codec, pilot and / or software? or any other possible remedies?

  Do you mean that you have an HP Pavilion zv5202us laptop?

  You have downloaded and installed the driver for the audio device provided by HP:
  ADI 1981 b Audio driver for Windows 2000/XP

  It is old - but...  So the laptop.  ;-)

• All music and audio sounds like chipmunks

  The sound on my laptop seems to have accelerated.  All music and audio sounds like chipmunks speaking on helium.

  Can help you?

  Hi johnstubbs,

  If you have the Realtek audio driver, this could be caused by karaoke settings in Realtek under digital output-> sound effects.
  Set karaoke at 0 of the Panel-> open Sound Effect Manager.
  or try this
  http://Windows.Microsoft.com/en-us/Windows7/tips-for-fixing-common-sound-problems

• I installed windows xp instead of win 7, so after that installation there is no audio, sound

  I installed windows xp instead of win 7, so after that installation there is no audio, sound
  What should I do?

  Install the audio drivers xp correct for your PC/laptop from the manufacturer's Web site.

  See you soon,.

  Jerry

• Pav HP dv7t-6100 CTO w/Beats Audio sound system resonates at levels above 50%.

  HP Pavilion dv7t-6100 CTO Entertainment Notebook PC with Beats Audio sound system havingf volume distortion of the issues.  At levels exceeding 50% a reverb effect to ab which gets worse the stronger volume.  Using Win 7 Hm Prem

  Problem solved itself.

• will not play dvd videos now play, but audio / sound, sound work otherwise on my laptop but when I play video on dvd or video file, why?

  will not play videos on my dvd player but the audio / sound, sound work otherwise on my laptop, but dvd and videos on file usually play sound/audio, WHY?

  Hello

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  ------------------------------------------------

  Start - type in the search box-> Winver find upstairs and double click on - check version

  You need Codec - get these if 32-bit

  -Free - CCCP also get free tool of insurgents
  http://CCCP-project.NET/

  FFDSHOW - free
  http://sourceforge.NET/projects/ffdshow/

  Check here:

  Plug-ins for Windows Media Player
  http://www.Microsoft.com/windows/windowsmedia/player/plugins.aspx

  ---------------------------------------

  VLC needs, of no use so usually Codec as a backup when asked to support associations of files just say no.

  VLC - free
  http://www.videolan.org/VLC/

  ============================================
  ============================================

  If 64-bit:

  Read this 1st and go that route, or use the one below.

  http://www.Vistax64.com/sound-audio/152850-Vista-codec-pack-32bit-64bit-Media-Player-codecs.html

  --------------------------------------------------------------------

  If 64-bit Vista - can run WMP in 32 or 64 bit mode.

  Or try these: download - SAVE - go to the place where your put them RIGHT CLICK – RUN AS ADMIN.

  For 32-bit use these - OR those listed above that I prefer.

  K - Lite Codec Pack 5.0.5 & K-Lite Codec Pack 5.0.5 update
  http://www.codecguide.com/

  Use them for 64-bit:

  K - Lite Codec Pack (64-bit) 2.6.0
  http://www.codecguide.com/

  -------------------------------------------------------------
  You know that you use WMP 32 or 64

  Change, change or set 64 - Bit Windows Media Player 11 (WMP11) in Windows Vista x 64 as default
  http://www.mydigitallife.info/2007/01/19/switch-change-or-set-64-bit-Windows-Media-Player-11-WMP11-in-Windows-Vista-x64-as-default/

  -------------------------------------------------------------

  And you can use it when necessary because no codex is usually required.

  VideoLAN - VLC media player
  http://www.videolan.org/

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• Upgrade cards, drivers, video, Audio, sound, XP, Windows, Windows 7

  I intend on my computer to upgrade Windows XP to Windows 7. If I update will it get new maps, sound and video cards/drivers for windows seven or my current criteria will work?

  I have:

  Video: Nvidia GeForce 6600 GT

  Audio: Sound Blaster Live! 24 bit

  Windows 7 Upgrade Advisor, find out how ready your system is:
  http://www.Microsoft.com/Windows/Windows-7/Upgrade-Advisor.aspx releasing It Easy: with Windows | ActiveWin | Laptops | Microsoft MVP

• Make audio sound like a portable radio - then back to full hi-fi

  For a project that I am, I need to do audio acoustics (initially), as it comes from a cheap, low - fi source - and also good audio source as it is located in a different room than the listener is in.

  If the effect is composed

  (a) make the audio sound thin and limited in frequency (I compare it to the old transistor radio)

  (b) make the audio sound muffled and continue with attenuation of volume level/frequency (as if she had played in another adjacent room the listener)

  For the second part of what I'm trying to achieve, I need audio to return quickly to its full Majesty, so in a case of a 3 - 4 seconds, the sound quality improves gradually from evil to good.

  I heard this effect on many records, but I have no idea how reproduce it successfully, any advice on this would be appreciated.

  Kind regards

  Steve

  There are several things that you need and it is much easier to do in multitrack, using the slopes of automation. The characteristic sounds that you need are limited frequency response (although all you need to do is probably down several hundred Hz bass), distortion and an effect reverb - this probably room in that order, and you must adjust to your taste. The idea is that you feed the frequency range restricted to the distortion and the consequence of a reverberation room short, but with the direct sound denied quite a long way (perhaps completely!) and just the wet feed creating the sound. If you use a reverb where there is a control on the first reflections, especially what you want, not so much the real reverberation.

  Once you have set up as a group effect, you should be able to dissolve at will.

• Satellite L30: audio sound does not work - WinXP SP2

  Hello

  I just bought a new laptop (Satellite L30 PSL33E-02S01LBT). He had installed Windows Vista, but it was horribly slow.

  I installed Windows XP SP2 on it's updates. I installed all the drivers from toshiba site I could find for my model.
  Everything works fine except the sound. I tried to install the drivers found on the toshiba Web site, but it fails with this error:
  'No pilot only is supported in the suite of drivers' (AKA FRENCH: 'no driver no is supported in this suite of drivers').

  In my list of equipment I have this with a "?":
  (?) Audio device on High Definition Bus Audio

  I tried to install the Realtek drivers with 5.10.0.5273 version.
  Found the driver here: http://www.mbnet.fi/ajuriapaja/info.asp?AID=10015&TID=10431&OS=10
  This driver has been installed successfully, but the sound still doesn't work.

  So, I removed this driver and found my "Audio on Bus High Definition Audio device"...

  What could I do? Is this computer model toshiba laptop has problems with XP and the sound?

  Thanks for the help...

  Mico

  [Edited by: admin on March 8, 2007 20:21]

  Thanks for the solution Abe! :)

• HP Envy 15 x 360: Audio, sound recording, but not releasing any

  Went to this for an hour and I tried all the previous solutions. I've updated, uninstalled/reinstalled, restart the computer, shoot bad, etc., but nothing seems to solve my audio. It is not a problem with the headphones as with or without them audio does not work. I think it's a problem with the speakers, but not quite sure.

  Product name: HP ENVY 15 x 360 PC
  Product number: J0E41AV
  Serial number: [personal information deleted]
  BIOS (Configuration):F.24-11/28/2014 (0978100000405F00000420180)
  Keyboard Review: 89.22
  Total memory: 8.00 GB
  Name:Intel (R) Core i5-4210U CPU @ 1.70 GHz processor

  Hi @mnma88 ,

  Thank you for visiting the Forums HP's Support and welcome. It's a great site for information and questions. I looked in your question about your computer laptop HP ENVY 15 x 360 and questions with no sound. Here's a documenton troubleshooting sounds if you need it.

  Please ensure that your edits were made on the laptop. In under his right click Device Manager and update driver. This is another step to try.

  1. right click the speaker icon in the lower right corner of your time.
  2. click on playback devices.
  3. click on speakers/headphones.
  4. click on properties.
  5. click on the Advanced tab in the Properties window.
  6. change the default menu Format in the highest quality.
  7. apply properties.
  8. click OK to close the Properties window.
  9. click OK to close the playback devices.

  Please let me know how it goes.

  Thank you.

• HP Envy Phoenix: Disabling Beats Audio Sound card in desktop HP Envy Phoenix

  Here's my problem, my HP Envy Phoenix office above came with Beats Audio standard install, I installed a new card his SoundBlaster Audigy 5/Rx installed fine, but one of my audio editing programs says

  The output of the sound card could not be defined at this sampling frequency: 44100 Hz

  Either the device does not support this sampling frequency, or it is in slave mode and its sampling frequency cannot be changed by elements of WaveLab. So how do I know if my new sound card is running in slave mode and how do I change this? or maybe disable the card Audio Beats?

  Thanks in advance,

  SP60

  SP60, welcome to the forum.

  Beats Audio should automatically be turned off when the sound card is installed.  However, you can go to the control panel Audio Beats and uncheck the "Set as default device".  You can do this with the recording device, too.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.