Screen stuck during the update

Similar Questions

• Get-9860 torch blackBerry Smartphones stuck during the update

  Hello

  I bought a new unit of bb now I'm updating everything and he's stuck during the update wat to do?

  Following currently being held in the screen for half an hour now

  

  Now it finally works

  glad to see that it works for you

• screen stuck on the logo of apple during the forced reset

  I bought an iPhone 6s + 16 gb.its iOS version was 9.1

  during the update iOS through the phone, the screen turns black but tithe.

  nothing start reset forced up.with (sleep + "home" button), stuck on the apple logo and nothing starts.

  What should I do?

  Thank you.

  I try again the forced reboot, but if it fails the second time, try putting the phone into recovery mode.

  If you are unable to update or restore your iPhone, iPad or iPod touch - Apple supports

• ENVY 100 printer D410 - screen says "Do not, power down during the update" permanently.

  I'm a Mac user Mavericks 10.9.1 running on a Mac Book Pro.

  I have a HP ENVY 100 D410 printer that works your for a few years.

  Recently, the LCD screen of the display on the printer offered, "there is a new driver. You want to update? "(Yes/no)

  (Or something close to that.)

  Unfortunately, I chose 'yes '.

  The printer then tried to update, but eventaully the LCD screen on the printer displays a flashing message:

  "Do not feed, down during the update"

  The printer now flashes just this screen continuously. The LCD screen will not display anything other than this message.

  The printer works when connected by cable and wireless. (Airprint works very well).

  I can scan documents, I can print pages, I can even access printers "Web page.

  But the LCD touch screen control panel is 'stuck' in flashing update message.

  I can't find any way to clear this error and allow the printer to complete the update.

  Help. Please, I beg you.

  Hello

  There is a fix to resolve the specific problem, but I'm afraid it is only available for earlier operating systems under OS X 10.5 and 10.6, Windows XP, Vista or 7.

  I you suggest to get a computer with any operating system supported, install the latest version of the software on the HP site using a USB and then follow the steps.

  The latest version of the software can be found below (the basic software should be sufficient):

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?cc=us&DLC=en&LC=en&OS=4062&product=4073738&softwareitem=MP-92513-1&sw_lang=&

  Make sure that you carefully go through the procedure to the installation section in the patch download page.

  Hope that helps,

  Shlomi

• Message "do not power down during the update"control panel screen not fade.

  Product name: HP ENVY 100 e - All - in - One Printer D410a

  Product no.: CN517A

  The message "Do not power down during the update" on the control panel of the printer refused to erase and remained perpetually disaloowing acess the Menu home for other actions as photocopies etc.

  I see.  I found this utility that will help you to solve the problem.  It seems the printer lost connectivity during an update firmware and glitch out.  The utility should take care of it.  Let me know what happens.

• iPad froze during the update and may not exceed

  Has obtained the new ipad and put in place.  Went do the last software update and it froze during the update process.  Blocked at the white screen with the apple logo.  Can not pass it and past 2 hours.  Tried to restore through itunes, but get the error that I need to enter my password which I can't because I'm stuck on the white screen.

  Hey there smbirchler,

  Congratulations on your new iPad! Looks like you were updating the iOS version, the device froze, and now you can't pass the white Apple logo screen, even after you try to restore in iTunes. I know how happy I am when I get a new camera, so we'll work together on that, so you are able to enjoy your iPad mini.

  We will have you try to use the device in Recovery Mode. Take a look at this article for how to do this:

  If you are unable to update or restore your iPhone, iPad or iPod touch

  Thanks for being a part of the communities of Apple Support!

• Windows 7 BSOD after accidental shutdown during the update

  Stop computer accidentally during the update of windows. Now computer stuck in a loop of startup blue screen. Safe mode and windows recovery all lead to the blue screen. I don't have a recovery disk. What should I do?

  Hello

  According to the description of the problem, your computer is stuck in blue screen loop. So, I suggest you to create installation media by following the steps described in the article mentioned below and after that try to run automatic reapir.

  Download Windows 7 Disk Images (ISO files)

  After you create the Bootable USB key, change the boot priority and set it to USB. If you are unsure it is advisable to contact manufacturer FRO even. After changing the boot priority is trying to start your computer by using the bootable USB key.

  To run the repair to start the Windows recovery environment (WinRE), follow these steps:

  • Insert the Windows installation disc in the disc drive, and then start the computer.
  • When the message press any key to start from the CD or DVD is displayed, press a key.
  • If your PC does not automatically detect the media
  • When the computer reboots, read on screen for instructions that explain how to interrupt normal startup and access the basic input/output system (BIOS) configuration utility. Most PCs use the F2, F10, ESC or del key to start the configuration of the BIOS.
  • Looking for a tab in the BIOS configuration utility that is labeled boot order, The Options of Bootor Boot. By following the instructions on the screen, use the arrow keys to go to the boot order, and then press ENTER.
  • Locate the flash USB, DVD or CD player (this could be called removable device) in the startup list. By following the instructions on the screen, use the arrow keys to move the drive to the top so that it appears first in the startup list. Press ENTER. The startup command sequence is now changed to boot from the flash drive, CD, DVD, or USB.
  • Press F10 to save your changes and exit the BIOS Setup utility. Select Yes in the confirmation window. The PC will restart.
  • Select a language, a time and a currency, a keyboard or input method, and then click Next.
  • Click on repair your computer.
  • In the System Recovery Options dialog box, select the drive of your Windows installation, and then click Next.
  • In the System Recovery Options dialog box, click on repair your computer.
  • Click the operating system you want to repair, and then click Next.
  • In the System Recovery Options dialog box, click Startup Repair.

  For more information about System Recovery Options, see What are the system recovery options in Windows?

  For more information about the Startup Repair, see Startup Repair: frequently asked questions.

  Hope it would help. If problem persists always post back with the current state of your computer and the result of the proposed suggestion, we will be happy to help you.

  Kind regards

• Satellite Pro L100 - Crash during the update of the Bios

  Hello

  I am the owner of a Satellite Pro L100 (PSLA4E)

  On the Toshiba site I downloaded the BIOS update. While installing I read that it was necessary to supply cable is plugged. Before I could cancel for the cable, he had started and then frozen. The computer stopped working and so I turned it off! Since then, I've read that it was a very big mistake!

  When put on the fan starts and I can hear etc cd drive spinning. After 15 seconds, the screen is blank, the computer starts beeping!
  Is there a way to solve this?

  Thank you very much
  Rich

  Hi Richard

  Seems not good buddy from your description, that something went wrong during the update procedure and now the ROM module has been flashed properly.

  Maybe you area lucky man and the motherboard isn't too bad, but only the Rom module must be flashed again.

  Unfortunately, this must be done by the technician of the ASP. You will need to contact the ASP in your country for assistance.

  Good luck and have a nice day

• Satellite A200-1TD - gel during the update of the BIOS

  I have a laptop model Satellite A200-1TD: PSAE0E, XP operating system

  I tried to update the BIOS and it did not work so he blocked. After that a few minutes, I tried to restart and it didn't worked so I unplugged the AC cable. After that, he did not answer. Black screen, no sign.

  Help, please

  Hello

  I think that, in this case, you can do nothing because the ROM module has to be reflashed and in the worst case the whole mainboard needs to be replaced.

  These freezes during the update of the BIOS can cause such problems as the laptop doesn't start over.

  Moreover, on the Web from Toshiba site you can find an authorized service provider:
  http://EU.computers.Toshiba-Europe.com/ > support & downloads > find an ASP.

  Welcome them

• 1130us Envy4 crashed during the update of the BIOS

  Hello!

  I just killed my laptop Envy4-1130us favorite.

  I decided to update the BIOS of v.13 to v.25

  During the update process, mogen of BONE (Win8.1) upwards. No error has been shown. After restarting laptop for a few hours, and now it is not working. Supply duct is turned on, the system fan works at full load, but the screen is black, and system does not (OS not start and does not not the power button).

  Community can help me? An it's the BIOS of the laptop recovery console?

  PS: Excuse my English.

  Update:

  When the laptop was completely unloaded, I plugged in the AC adapter.

  It powers on and then the bios recovery procedure has been started.

  So now I have a BIOS v.10

  Thank you HP Bot now my desire to NEVER been updated bios

• accidentally turned off during the update of windows

  Guys, im using sony vaio with vista premium OS and it is automatically updated, I had used to remove my battery for use at home, during the update of windows, I accidentally kick off the power cord and it disconnected from the main power switch and turned off, when I open it I saw a note on the bottom right 'tm this copy of windows vista is not authentic.

  someone could help me on this guys, how can I do recover without reformatting my laptop.

  Please help me guys...

  Thanks in advance...

  Needless to say, cutting the current during the update process can cause all sorts of problems - many not even related to the update itself.  It is a common branching.

  Do you know when this problem started?  Try a system restore to a point in time BEFORE the problem started.  Here is the procedure: http://www.howtogeek.com/howto/windows-vista/using-windows-vista-system-restore/.  Don't forget to check the box to show more than 5 days of restore points.  If the first attempt fails, then try an earlier point or two.  NOTE: You will need to re - install any software and updates that you have installed between now and the restore point, but you can use Windows Update for updates.  I don't know if this will solve the problem, but it might.  It's worth a try (and it can be useful if there are other problems that you have not yet detected).  Whether or not it works, you will need to re - install the update (and this time won't turn off - LOL).

  If you still have the problem of validation after system restore, and then click Start / computer / system properties and check the bottom of the Activation section.  Your system always shows that it is enabled?  If this isn't the case, then reactivate.  To activate manually, go to start, search, and type in slui 4 enter.  Enter your country and press Next.  You will be on a screen with a phone number and a bunch of codes below.  Dial the number and browse automatic guests until you get to a human being.  Have your handy product code because it will be asked.  Explain the situation, but it's the same PC.  They should give you a code to enter on this screen to activate Vista.

  If this does not resolve the "not genuine" message, please post your problem in the Windows Genuine Advantage Forum: http://social.microsoft.com/Forums/en-US/genuinevista/threads , where the experts on this kind of problem will be more than happy to help you with your problem.  They will probably ask you to run a program and download the results so they can examine in order to find the problem - just follow their instructions.

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Vista froze during the update. Can I stop?

  Hi all.

  I tried to update my friend with Vista Service Pack 1 computer, but it froze during the update.  I tried to cancel the download task manager and restarting, but it is now fixed on the 'day of the installation.  Do not unplug or turn off your computer"screen.  It made no progress.  Can you force shut down the computer?

  Thank you
  Angela

  Hello

  give him a little more time

  If it continues like that and you must stop and restart problems, try the following steps to solve this:

  1st thing to try would be a restoration of the system in safe mode

  http://www.windowsvistauserguide.com/system_restore.htm

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode option with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  If that does not read this information

  the link below is how to download and get a vista disk startup repair, which you can start from the

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  Here's how to use startup repair system restore command prompt, etc. to bleepingcomputers link below

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start

  It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu

  Change boot order it do dvd drive 1st in the boot order

• Smartphones from blackBerry Torch 9800 completely erased during the update

  When I plugged my phone into the computer to charge, an update came on the bb Desktop Manager - to update to 6.0 Bundle 2467 - and I started the update.  After a few minutes, I realized that I have to back up my phone before the update but Office bb wouldn't let me - he said that HE had to be updated.  If the device software update paused until the Office update was complete.  When it was over, the update of the device continued... and I have no back upward.

  Somewhere in the middle of the update (after about half an hour) the phone blinked, there was funny "beep" and a message came that the update could not continue.  The phone has rebooted, but was stuck at about 65%.   I let it sit for a few minutes, still doesn't move do not.  Pulled the battery, let stand a few minutes like that and then reintegrated.  Began to restart, then won again at the same place.  Taken from the battery after a few more minutes and wait for about 15 minutes.

  When I put the battery back, the phone quickly started completely... but because the updater won Mid-implementation to date ALL is lost! Contacts, calendar, memos.

  Is it possible to recover whatever it is? Or all my data lost somewhere in cyberspace is?

  * There is a small file, about 5 MB called Contacts Blackberry so I thought I could synchronize the files from there, but I don't know how!

  Can anyone help?  Really aggravated in this topic...

  Hello and welcome to the community!

  First of all, we will be sure your BB works correctly and with the proper operating system. Is it? What you have said, I can't say for sure. If it does not work, then you can reload your new OS itself, just to be sure. Don't worry about all the data on your BB... he already went there now (based on what you said).

  For your data, Desktop software must have made a backup during the update process... sometimes, we offer the chance to overcome that... I hope that you do not have. In any case search your computer for files with the extension of the IPD or BBB (depending on the version of the Desktop software you use)... These are the files that would have been created on your computer when the update process performed the backup. Look at the time, the files were created... created around the time you were doing the update are candidates to perform a restore of your BB.

  Otherwise, if you had made use of yourself of the free app of the BB Protect your data are indeed "in the clouds" available for to restore you.

  In addition, if you use a Desktop Organizer (for example, Outlook), which must contain your data.

  In addition, if you have none of these, then you have indeed now met data loss, which is sad indeed.

  Good luck!

• using office creative cloud up-to-date PSCC and CRD.  PSCC updated very well, but it froze during the update of the CRD. What to do now? Chat is closed.

  Creative desktop cloud application froze during the update.  Updated fine PSCC but LRCC froze before it has been updated.  What should I do now? Chat is closed.  ON the home screen of the creative cloud desktop application it usually shows my activity - but now it says nothing except "your hoome stream is empty.  Should I download new creative cloud app - it's corrupted?

  Hi Carol,.

  Please follow the steps below:

  (1) uninstall Adobe CC (use of the Adobe Creative Cloud cleaning tool to solve installation problems)

  (2) restart machine

  (3) install the application Adobe CC since the help document: use of the desktop application cloud creative to manage your applications and services

  Kind regards

  Sheena

• An error occurred during the update the firmware. -16

  I tried to update the firmware, after restarting Airport Extreme. But the Airport utility shows that an error occurred during the update the firmware. -16

  I had to restore the factory settings by using Utility button and physics of the airport, but it has not solved the problem.

  I had to restore the factory settings by using Utility button and physics of the airport, but it has not solved the problem.

  I'm not sure what is the problem...

  Your airport is now not working? That is, the reset did not work.

  OR

  It doesn't have to be upgraded after several attempts?

  The airport is connected to the network as usual? You have full internet access through the airport?

  What model is the most convenient airport?

  The real model number could be a help. A1xxx of the base except the newest one... Suffice to say a grand.

  What is the current firmware?

  If it is a very old model, they can sometimes give wrong if it has never been updated.