Service Console memory Conf

Similar Questions

• ESX 3.5 Service Console memory

  I run an ESX 3.5 server and it has 800 MB of memory allocated to the service console. We use IPMonitor to monitor our servers and uses 750MO regularly for a while now. Is it necessary to upgrade the service console memory? Then the cause of performance problems?

  Thank you

  Scott

  The important line is the + / cache line, which shows that you have 480 MB of free space.  You're golden and good to go.

  Basically linux (which is the service console) will use 'extra' memory for caching, leading many monitoring programs to believe you have only 26 MB of free space in this case.  Recommend that you find a monitoring program that is more intelligent.

  -Matt

  VCP, vExpert, Unix Geek

• Memory almost full service console

  Hello

  I recently increased to 800 MB service console memory. The hosts have been working well before and were not maxing out the initial amount of memory. But now its use about 770MB on all servers. When i run 'top' it lists 320 treaty most of them are webaccess. Is this normal?

  Thank you

  You can use "swapon-s" or "cat/proc/swaps" to see your swap information.

  Your output, you use for your extended partition, which you use to block 17769 blocks "1357 17769 131837422'.  This means that you have 0 space on your disk for additional file systems. You will live with a swap that is not 2 x your memory.  Not a good thing, but it won't really hurt you that much.

  -KjB

  VMware vExpert

• Service console uses what memory?

  When I connect to the service console, I see that 700 of the 800 MB of memory is used when I run the "free-m. If I do a top or a ps - to, it's not really all that consumes a lot of memory (other than the workers spend - 12%). Is there a way to determine which uses as much memory? 700 MB seems higher it works normally.

  Thank you

  Scott

  It is a common conception of GIS-ism/Linux.

  The system uses 661 MB of memory.  However, only 170 MB is used for applications.  Linux is actively using any otherwise unused memory for caching of file system, which is what you see here under "buffer" and "cache."  To the point that an application requests more memory, Linux will reduce the size of buffer and cache and give him more.  Here is a similar explanation: http://www.linuxatemyram.com/

  So if you want to monitor the memory usage, you must monitor (USED - BUFFER - CACHE), which is what gives you this second line.  So realistic, your system uses 170 MB for real applications and the RST for implementing caching file system.

• Can I create a second service console in ESX 2.5.5?

  Can I create a second service console in ESX 2.5.5?

  Yes, I did in ESX 3. +, but I can not find/check it's ok in ESX 2.5.

  Procedures, orders or comments appreciated.

  ALL POINTS WILL BE AWARDED.

  No, you can not - the service in ESX 2.x actuallys console loads before the vmkernel and has control over its own NETWORK card and the physical memory - in esx 3.x (vSphere) the VMkernel charge first and provides these resources to the service console allowing you to create several service console ports -

  If you find this or any other answer useful please consider awarding points marking the answer correct or useful

• Service Console problem

  I try to install ESX4.0 in our test environment, I have checked so that all the

  esxcfg-vswif - l

  esxcfg-NICs - l

  esxcfg-vswitch-l

  the parameters of air but can not 'ping' of the Service Console to other servers or can I 'ping' even the gateway to the ESX host.  I've tried deleting and recreating the vswitch and vswif, but can not get the ESX to access the network or access the ESX from the network through virtual Center.

  I have already activated the SSH and try and putty, but can't.

  Any suggestions on what might be the cause, I already checked the 'hosts' and /etc/resolv.conf files but can not identify why I can't connect to the ESX host.

  Any help appreciated.

  See you soon

  I tried to add an ESX4 (trial mode) for the VC2, 5 and cannot me.

  It is not possible.

  You need VC4 to manage ESX4.

  André

  * If you found this device or any other answer useful please consider awarding points for correct or helpful answers

• Is it ok/possible to add a GUI to my ESX server service console?

  Can I download one of the lightest LINUX GUI and run it from the service console?  Also, how to connect using putty?  Should be on licence somewhere?

  You can add a graphical interface on the ESX console... Can be... but be careful that the console has only a limited amount of Max (above 800 MB) memory and it has been optimized to manage your virtual machines. He is also set to always run on CPU0.

  If you interfaces graphics crashes... it could take down the management of all your virtual machines.

  So the question is "If you do that?", then the answer is no. you'd better not.

  It also cancels your support/warranty. Your ESX Server will be is no longer supported.

  If it's for an experience... go ahead... If you want to run production on this same host... don't even think about it.

  --

  Wil

  _____________________________________________________

  Visit the new VMware developers at http://www.vi-toolkit.com wiki

• Change the IP address of the Service Console

  Hi, when I try to change the IP address and the address of the gateway to the Service Console NIC on the console, I always get this message:

  !!! WARNING!

  Loss of connectivity network may occur if the parameters not valid in

  Add, remove, Portgroup or IP operations.

  and nothing is changed. How is it possible to change the IP address of vswif?

  I try with the command "esxcfg-vswif!

  Thank you

  Hello

  There are two ways of CLI to chang the IP address of the service console.

  Either remove the current vswif0 and recreate it using esxcfg-swif.

  But as you must change the ip address of the service console, you can try e under method, change the entries in the file.

  for the ip address and the mask of the service console, you can change the entries in the file below.

  / etc/sysconfig/network-scipts/ifcfg-vswif0

  and for the gateway, host name using the file below

  sysconfig

  for the dns entries

  /etc/resolv.conf

  After all the changes, try to network service.

  service network restart

  Let me know if you need more information.

  -Aurelia

• services.exe memory consumption and therefore 15 minutes to start

  services.exe memory consumption and therefore 15 minutes for bootProblem Description: it seems that since the installation of updated KB973687 my Dell Inspiron 640 m takes an age to start. I am running XP SP3 with all updates installed, have 2 x 512 MB memory installed and the basics of microsoft security is enabled and no virus detected. Run the task on the Startup Manager, I see that services.exe 2 user running objects. Maximum memory use reaches about 500 000 to 600 000 k and the size of the virtual memory increases to more than 2,000, 000 k. Once the VM reached approximately 2 200 000 k it starts to release very slowly and finally reduced to a size of about 6 000 - 7, 000 k, then just a race of user object. It is not until that time where the system becomes usable. What is happening at each startup and lasts about 15 minutes for the system be usable. I have read many articles on this issue, and the other that a clean reinstall which I do not, cannot find a solution. Your help would be greatly appreciated. Operating system: Windows XP

  Your list is very different and much longer than mine. My first thought is that you have the programs loading at startup that might as well load up on request. A useful tool for watching the startup items is Autoruns.

  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx

  Google search result - report

  http://www.Google.co.UK/search?SourceID=IE7&q=Rarrort+service&RLS=com.Microsoft: en - gb:IE - SearchBox & ie = UTF-8 & oe = UTF-8 & rlz = 1I7ACAW_enGB397GB397 & redir_esc = & ei = mgTwTLvpE4GxhAeUtZSUDA

  Right-click on the report, and then select the graphic Performance. What is the CPU usage and the private bytes. I suspect that you need to know the use during StarUp but for now know how to do this.

  I'm intrigued by the absence of references to other security software. What antivirus, antispyware and firewall do you use?

  Hope this helps, Gerry Cornell

• Remote Access Service Console

  Is there a way to access the VMware host service console remotely?

  Try to run the command "dcui" in an SSH session...

  Direct Console User Interface (DCUI) since a SSH session access (2039638). VMware KB

  / Rubeck

• Trade rules do not appear in the Regional service console

  Guru HI

  We use the Application confort Hyperion Planning 11.1.2.2.

  We have created business rules for our planning application using Calc Manager and they work very well.

  But my doubt is that calculations do appear in the essbase.

  WT could be the reason for this... Please suggest.

  Thank you.

  Hello

  The Regional service console will show you only the calculation scripts, not the rules for calculation of the Manager. This is a technical limitation.

  Prior to version 11.1.2.3, we also had business rules. These were available in the Regional service console. Then, you had a section in the view of the company next to Administration, servers Essbase called Business Rules. I usually call them Hyperion Business rules (HBR) because users easily get confused with all the scripts and rules.

  In planning, you can see the calculation scripts and rules for calculation of the Manager.

  I hope that clarifies the situation and will help you.

  Kind regards

  Philip Hulsebosch

• Please explain number maximum support of the virtual machine by exsi 5.5 and exsi 6 service console

  Please explain number maximum support of the virtual machine by exsi 5.5 and exsi 6 service console

  What exactly do you want to know?

  For supported máxima, see one of the following documents:

  https://www.VMware.com/PDF/vsphere5/R55/vSphere-55-configuration-maximums.PDF

  https://www.VMware.com/PDF/vsphere6/R60/vSphere-60-configuration-maximums.PDF

  Full documentation can be found at:

  https://www.VMware.com/support/pubs/vSphere-ESXi-vCenter-Server-pubs.html

  https://www.VMware.com/support/pubs/vSphere-ESXi-vCenter-Server-6-pubs.html

  André

• What is the cause of the message "Waiting for Service ' Console CVD activity

  I have two related questions.

  basis, I just started centralizing 200 computers ish, all except 2 appears fine, 2 questions, one below and another with VSS errors.  This message is just for the question "in waiting for the Service.

  1. What is the cause of the message "Waiting for Service ' Console CVD activity and is there anywhere that documents these meanings of status.
  2. No idea where I should start troubleshooting the message "Waiting for Service ' I get to the computer below.

  I have a computer with this status which comes to have installed the client and will not be to centralize.  Other computers seem to work properly (centralized).

  The computer is to ping requests, but appears as disconnected in the console.

  I deleted the CVD and restarted the centralization CVD using a different policy on a different volume without change.

  Journal of the history of CVD below

  Description of the Type of weather

  31/01/2014-08:52:32 AUDIT_EVENT assign device, device: PC30866 (1995), cardiovascular disease: 11614, political CVD: don't Default - every 4hrs - no drive D (1.1)

  02/05/2014-13:53:58 politics AUDIT_EVENT assign CVD, CVD: PC30866 (11614), CVD policy: Migration Post-quotidien (1.0)

  31/01/2014 General Office EVENT 20:44:46 service error

  31/01/2014 General Office service EVENT 17:39:04 error

  31/01/2014 14:44:34 EVENT has not finished downloading, internal error, exception attached

  31/01/2014 General error from the EVENT 13:05:15 service office

  31/01/2014-12:30:37 TRANSACTION_START PC30866 - centralize endpoint

  the transaction log has an inscription mentioning a failure (not sure if it is the server or PC related) disc.

  Diseases cardiovascular diseases cardiovascular name Type State layer size (MB) data transferred (MB) branch reflector savings start time end time transfer (MB)

  Of the endpoint PC30866 centralize 11614 reading disc failed 169648 1531 0 31/01/2014 12:30:37 05 d 04:16:52

  The next event is in the application event log and the Mirage event log for the failed computer. (there were not all other errors in the paper since the deployment of mirage customer and there is no errors in the system event log)

  Event type: error
  Event source: VMware Horizon Mirage customer
  Event category: no
  Event ID: 0
  Date: 31/01/2014
  Time: 20:44:46
  User: n/a
  Computer: PC30866
  Description:
  Error general service office
  Unexpected exception taken (sender Name:Wanova.Desktop.Service.exe
  There is no policy context.
  , the object exception System.OutOfMemoryException: Exception of type 'System.OutOfMemoryException' was thrown.
  System.Collections.Generic.List to ' 1.set_Capacity (Int32 value)
  System.Collections.Generic.List to ' 1.EnsureCapacity (Int32 min)
  to System.Collections.Generic.List' 1. Add (T item)
  at Wanova.Net.DataTransfer.TransferStreams.SignatureResponseStream.ProcessChunk (ChunkInfo chunkInfo)
  at Wanova.Net.DataTransfer.TransferStreams.ChunkInfoDecodingStream.BeginWrite (Byte [] buffer, TransferStreamWriteCallback onWriteComplete)
  at Wanova.Net.DataTransfer.DataHandler.ExecuteDataStreamTask (DataHandlerExecutionTask task, MarkCompletionCallback markCompletionCallback)
  at Wanova.Net.DataTransfer.DataHandler.ExecuteTask (IExecutionTask task, MarkCompletionCallback markCompletionCallback)
  Wanova.Net.DataTransfer.ExecutionController.QueueListener (Group IExecutionTask)
  to Wanova.Common.ThreadUtils.ParamaterizedWorkItem'1.Run (object fakeParam)
  at System.Threading.QueueUserWorkItemCallback.WaitCallback_Context (Object state)
  at System.Threading.ExecutionContext.Run (ExecutionContext executionContext, ContextCallback callback, Object state, Boolean ignoreSyncCtx)
  at System.Threading.QueueUserWorkItemCallback.System.Threading.IThreadPoolWorkItem.ExecuteWorkItem)
  at System.Threading.ThreadPoolWorkQueue.Dispatch)
  at System.Threading._ThreadPoolWaitCallback.PerformWaitCallback (), ends at True)

  For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

  It turns out that this computer seems to have hard drive errors, so not a matter of mirage.

• Unable to connect to the administration via the regional service console server after 11.1.2.2 installation

  Hi gurus,

  I have installed and configured the services foundation, eas and essbase in windows 2003 server, afteEA r configuration I have observed that there are no tables for eas schema then I found that it was a bug and applied patch and set up again it has been successfully configured.

  When I tried to connect to the administration via the regional service console server. He States unable to connect to the administration server. everything else works.

  I see only 4 services in services.msc

  Oracle hyperion configuration manager

  EMP web server application

  opmn services

  OSH services

  all services are started with the exception of oracle hyperion configuration manager. I tried to start, but it does not start... is - this service has an impact on the administration server.

  I checked the logs, I can't find anything in easserver.log.

  any suggestions?

  Kind regards

  Kumar

  Looks like you have deployed web applications to a single managed server that is running on a port by default of 9000, then try to add the server to the Regional service as servername:9000

  See you soon

  John

  http://John-Goodwin.blogspot.com/

• Essbase Cluster node not get is expanding in the Regional service console

  Dear all,

  We use version Hyperion 11.1.2.1. I faced a new problem in Regional service console. The Essbase Cluster-1 node in the service console Regional expanding not when I tied to drilled her. For this reason, I am unable to view the applications, calculation scripts, etc. We need to run calc scripts and to add new members in the application.  Any body experienced this before? Kindly guide me to solve this problem issue.

  Thank you

  SC

  If you use the web console EAS, then make sure you are using a supported Java version, if it is supported, and then try adding the server essbase with the hostname instead of cluster.

  See you soon

  John

  http://John-Goodwin.blogspot.com/