Service manaul for Portege A600 PPA60A

Similar Questions

• Portege A600 PPA60A - unable to download Windows 7 drivers

  I have an old PC of 3 months I'm trying to get upgraded to Windows 7. It's a Portege A600 PPA60A 01H00G

  I tried to use killed HIM and it fails at the step where it downloads drivers

  I then tried to manually download the drivers from this page:
  http://support.Toshiba-tie.co.jp/Windows7/download/PORTEGE_A600_32_au.htm
  But none of the th elinks on this page to work. I guess that's also why KILLED it fails during download too.

  Note that I'm in Australia, but for some reason any support Australian forum redirects here.

  Thank you

  Hi simon13,.

  Well, I tried to download drivers on the Web site that you posted but I can't notice t a problem. All three drivers tried to downloaded are worked correctly.

  Maybe it was a temporary problem and Toshiba did solve this problem. I think you should try it again. :)

• Replacement keyboard for Portege A600-120

  Hello
  can someone tell me what the size of the connector must be on the Portege A600-120 keyboard?

  My keyboard failed last week and I ordered a new one that was supposed to be compatible with A600 but the connector was too broad.

  Mine is a thin flat 15mm wide ribbon.

  Keyboard serial number is G8C000903EN, but a Google serach watch is the keyboard for the R500...

  Thank you

  Hello

  As far as I know the keyboard cable is connected to the CN3230 on the motherboard.
  The CN3230 is a dish * 30pin * I / F connector

• Need PCI Simple Communications Controller driver for Win7 for Portege A600-122

  Hello

  I put Windows 7 x 64 on my Portege A600-122 and have a "PCI of Simple Communications controller" in Device Manager. It seems that it is because the Intel AMT (Active Management Technology) driver is not installed.

  I am struggling to find it, there is a [driver Windows 7 x 86 | http://uk.computers.toshiba-europe.com/innovation/jsp/autoDetect.do?service=UK&ACTION=PROCESS_DETECTION& TYPE = FORWARD & SOURCE = SMP & COUNTRY = 242 & RQS = TRUE & MODEL = PORTEGE + A600 & SERIES = X8100601H & service = UK & LOCAL = & OSBUILD = 7600 & SUB_TYPE = SMP & OSBITSIZE = 64, & PANUMBER = PP A61E - 008008EN & ERROR = 0]

  and a [driver Vista x 86: http://uk.computers.toshiba-europe.com/innovation/jsp/autoDetect.do?service=UK&ACTION=PROCESS_DETECTION& TYPE = FORWARD & SOURCE = SMP & COUNTRY = 242 & RQS = TRUE & MODEL = PORTEGE + A600 & SERIES = X8100601H & service = UK & LOCAL = & OSBUILD = 7600 & SUB_TYPE = SMP & OSBITSIZE = 64, & PANUMBER = PP A61E - 008008EN & ERROR = 0]

  but I can not find a driver Windows 7 x 64, will make one of the above, or there at - it another link to the x 64 driver?

  Thank you

  Hello

  Please, try to download and install:

  http://www.DriverCure.com/driver/driver_captcha.php?device_driver_id=5CFDA707-11B0-4FEC-8C89-65E3E4EA9AFD

• Second disk for Portege A600

  Add second HARD drive instead of the DVD in my Portege A600-157 player?

  Hello

  As far as I know that's not possible with the Portege A600 series.
  My knowledge and some other series Portege M400 Portege or Portege M7xx series supports an Ultra Slim HDD Bay adaptor in order to is to insert a second HDD instead of the A600 but CD/DVD drive does not support this

• Portege A600 Webcam software crashes when changing the settings with the sound muted

  I have a problem with XP Toshiba factory build for Portege A600 and Portege R600.
  If you try to change the sound properties of the Webcam using the Camera Assistant Software with the sound muted, the camera wizard app will hang & Windows fails to shut down or even stop. The only way to stop is pressed the power button until the machine stops.

  So far, the only solution I can come to is to increase the volume to zero rather than using the mute box. The problem is if you forget and mute rather than turning down and then try to change the sound properties, its "game over." In addition, it is not really satisfactory because politics is to keep the machines muted until the sound is required.

  This does not happen with the Vista Build, build it only XP.

  My guess is that this will not happen on any machine using the Chicony Webcam & software with the Realtek HD audio but I have not tried on machines enough yet to be sure. So far, I've recreated on two A600s and a R600. The machines are not defective and you can create the problem, "straight out of the box. Just do the following:
  (1) use the provided Toshiba product recovery DVD for restore factory Toshiba Windows XP SP2 version
  (2) once you have done the whole stuff, mute
  (3) open the Camera Assistant Software application & to select Properties
  4) click the audio settings tab

  That of all, suspended. The Camera Assistant Software version is 1.7.209.0807L which seems to be the last being available for download on the websites of Toshiba.

  Someone has encountered this or have any suggestions?

  Hello

  I n t have a Portege but U400 with pre-installed and integrated webcam Win XP.
  I installed a clean Win XP and then upgraded the XP to the last State and installed all the drivers available from the Toshiba page and possible.

  I followed the steps in your message and I have to say that I didn t notice strange questions, software webcam still works correctly

  I put t know what could be the problem, but I recommend that you check the audio driver to update maybe you can use the Realtek page
  Also, check if the BIOS has been updated to the current state and if your Windows XP is up to date.

• Portege A600-12O - impossible to reinstall Windows XP

  When reinstalling windows XP on Portege A600-12O, I get following error:
  Integrated HARD disk errors: the product recovery CD can not reinstall the operating system.

  As well, I try to install XP SP2 using Microsoft cd (.. .needless talk without success)...
  following error is flashed on the screen:
  A problem has been detected and windows has shut down to prevent damage to your computer.
  If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps:

  Hello

  In my opinion, the Toshiba Recovery disk error message is very interesting and says a lot. What do you think about this?

  If your HARD drive is defective, you need a new and you are not able to reinstall the OS. Maybe your HARD drive needs to be exchanged.

  In your case I would contact an authorized service provider. Technicians can check your laptop and if it of under warranty, you should get a new HARD drive for free.

  Welcome them

• Portege A600-138 with Vista 32 bit does not see the computers in the Group Win XP network

  Hello

  My Toshiba Portege A600-138 with Vista Business 32 does not see the computers in the workgroup.
  In our office, the computers are all equipped with Windows XP.

  When I connect my laptop to the Local network, I don't see any neighboring computers in Network Explorer.
  I spent 1 hour and 40 minutes to talk to a specialist Service of Support from Microsoft, and the only way to have access to local machines, we found it had to enter the IP of the computer directly into the computer browser path field.

  I hope you understand what I mean.

  The man said that he had no this problem with non - OEM Windows Vista versions.
  He meant that the problem was with the oem versions of Vista preinstalled on laptops only.
  He said that probably the sellers - in my particular case Toshiba - supplied their notebooks with VIsta oem images that were somehow corrupt.

  Does anyone have an idea of the cause of this problem?

  > The man said that he had no this problem with non - OEM Windows Vista versions.
  > It meant that the problem was with the oem versions of Vista preinstalled on laptops only.

  That's nonsense for me
  The Vista OS preinstalled Toshiba which is same BONE as full Vista disc from Microsoft.
  There is only one difference; Toshiba laptops are preinstalled with Toshiba and pilots tools and drivers and tools are part of the Toshiba recovery image that contains Vista, driver and tools

  Check this box:
  http://www.Computerworld.com/s/article/9019179/Teach_XP_and_Vista_to_play_nice_on_networks?taxono myId = 16 & pageNumber = 1

  You will find information that a problem has to do with the new Windows Vista network map.
  Windows Vista uses a new Protocol (Link Layer Topology Discovery).
  LLTD is integrated with Windows Vista, this is why they appear correctly in the network map.
  But the problem is that LLTD is not integrated with Windows XP, which is why they do not appear correctly.

  But you can fix the problem by downloading and installing the layer topology discovery responder.
  Install it and your PC Windows XP will appear on the network map.

• Portege A600-13D - webcam stopped working

  Hello

  I have a Netbook Toshiba Portege A600-13D old, I am very satisfied with it, but lately the WEBCAM does not work and I have no idea what to do. If I try to activate the camera, I have the answer:

  The WEB camera could not been initialized

  Systemcontrol is the message:

  The camera could not been started, Code 10

  If I look at the driver and try to update, the message is:

  The optimal driver is already installed

  Maybe someone has an idea of what I can do and how to proceed. Sorry my bad English!

  Thanks in advance and best regards
  gh_1929

  Hello

  Error code 10 means that the device could not start.
  This may be related to driver problem (software), but also hardware problem.

  Let's see if its a software issue: check that I recommend you to uninstall the software for a Chicony webcam first.
  As far as I know, you should be able to uninstall the software in the control panel? programs & features.
  In the case of the Chicony webcam software is not listed here, go to Device Manager and uninstall the webcam driver which you should find in imaging devices.

  After the system restart, go to the page of the Toshiba UE driver and download Chicony webcam software to perform the new installation.
  You will probably need to restart the laptop once more to make it work properly.

  So lets hope that this accelerated procedure would solve your problem of course that if the problem is related to the problem of software.

• Button Portege A600 - 133 Windows 7 64 bit problem

  After installing windows 7 64 bit on Portege A600-133, Toshiba or Toshiba Assist button a presenter button work. All other keys are working properly. How can I solve this problem?

  Hello

  Have you installed the latest VAP (value added package)?
  Toshiba page provides the last Win 7 VAP for A600 which is v1.2.40

  You use the latest version of the BIOS?
  Check it!

• Portege A600-133: DVD player disappears from my computer

  Hello

  I have a laptop Portege A600-133.
  First of all, it is slow at the opening of my computer screen.

  Second: after ejecting a disc dvd or cd, Windows still shows the contents of the disc, the system hangs for a while, a USB unplug sound can be heard and the dvd player disappears from Windows (in my computer / Explorer / Device Manager)

  What this may be?

  I did already the round of upper/lower filters in the registry, but it does not solve the problem...
  I opened the computer laptop and checked the wiring to the dvd drive, cleaned the contacts, supported on the connectors.

  But the problem is still there...
  OS = Windows XP SP3

  Kind regards

  Arjan

  Hello

  My first idea was to remove the upper and lower registry key filters, but it seems that you have already done this.

  Nevertheless, here is a knowledge of MS on the upper and lower filters article mentioned.
  http://support.Microsoft.com/kb/270008/en-us

  Hmm if the unit is not present in the device manager then this means that the device is not connected or he's dead

  You should check if the ODD (optical disc) is recognized in the BIOS.
  You should also check if it of possible to boot from the bootable CD.

  If this is not possible then it may mean that your WEIRD malfunction

• Portege A600-133 - Slim Port Replicator III does not entirely

  Hello...

  I just got a Slim Port Replicator III (model PA3681E-2PRP) and annexed a number of devices (a VGA monitor, a USB keyboard and a USB mouse), according to the user manual.

  The unit, however, does well with my laptop (a Portege A600-133). Specifically, the laptop battery does not, the devices are not recognized and docking led remains off. However, the laptop turns on and off of the port replicator power switch, and the ethernet port also works very well.

  Clues?

  Thank you!

  Dimitris

  Hello
  I also had problems with the Portege A600 and Slim Port Replikator, when I just connect, works all good! Maybe it's too you, when you try to connect to the port Slim R. you: with your hands the laptop with Slim Port R. extra press together in the Air about where the connector is, one when she makes "Clack" and then a right is connected!
  Sorry for my English

• Portege A600-175 - failed to start the card reader device

  I got a Portege A600-175 running windows XP SP3 with a problem in the card reader device. Insert an SD card, it makes the sound that USB devices usually do when inserted (and also when it is removed) bur it doesn t appear on my computer. Do the Device Manager, it appears as a disc with an exclamation point on it and in properties, I see the error this device cannot start. (Code 10)

  I ve already removed the device and let windows find and install again but the problem persists.

  Thanks in advance for looking into it.

  Hi fjdc,.

  I think that you should look for an update to the driver on the Toshiba site:
  http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

  Remove the old version, restart the computer and install the version of the Toshiba page.

• Portege A600-128 - no card detected WiFi and no sound through headphones

  Hello
  I recently encounter some problem with my portege a600-128. Not illustrated, wireless network adapters a so no wifi detection, more when using headphones, realtek HD audio software detects them being plugged, but no sound is not output - I was wondering if it is a problem with the software, or perhaps of a damage...

  Re: wifi, I tried to download the driver realtek_wlan_20100225.zip on the site, but nothing has changed. In fact, the single adapter in Device Manager is the adapter broadband toshiba f3507g mobile, and in network connections, I don't see this one. Try to "find the hardware changes" in Device Manager only managed the laptop to realize that my Alps pointing device (touchpad) is not installed (if she always worked and always made)-trying to install tpdrv-20081103180427. ZIP has not changed anything...

  Thanks for any help!

  Hey Buddy,

  Have you checked if the WiFi is enabled by using the FN + F8 key combination? If your laptop is a hardware WLAN switch, it must be defined on IT!
  In addition I recommend you load the default settings in the BIOS.

  On your sound problem, have you tried to update the audio driver?

• Portege A600: 3 G radio off and can depend on the use of Win 7 64 bit

  I have a Portege A600 with 3G (Ericsson F3507g).

  The Wireless Manager says the radio is off and I should activate it via the hardware switch.
  The switch is turned on, but only effects the Wifi and Bluetooth. FN + F8 does nothing.

  All the drivers are installed and I also installed RF 3 G utility.
  There is nothing in the BIOS referring to WWAN. I have Windows 7 64 bit installed.

  I saw a suggestion to install the value Pack, but the two zip files will not extract because they suggest that they are part of a multi zip pack.

  > I saw a suggestion to install the value Pack, but the two zip files will not extract because they suggest that they are part of a multi zip pack.

  [Value added Package | http://www.toshiba.eu/innovation/download_driver_details.jsp?service=EU&selCategory = 2 & selFamily = 4 & selSeries = 243 & selProduct = 821 & selSho rtMod = 797 & language = 13 & selOS = all & selType = all & yearup load = & monthupload = & dayupload = & useDate = null & mode = al lMachines & search = & action = search & macId = & country = all & selectedLanguage = 13 & type = all & page = 10 & ID = 73571 & OSI D = 30 & driverLanguage = 42] must be installed to use the function keys and activated the WiFi / 3G.

  After downloading, you can decompress the package. Then, you will find a file .exe inside the new folder.
  This exe file is also a zipped package. You can extract this right click on the exe file and choosing extract here. Then you will find the setup.exe file, which should launch the installation

  But before doing the [pilot 3 G | http://www.toshiba.eu/innovation/download_driver_details.jsp?service=EU&selCategory = 2 & selFamily = 4 & selSeries = 243 & selProduct = 821 & selSho rtMod = 797 & language = 13 & selOS = all & selType = all & yearup load = & monthupload = & dayupload = & useDate = null & mode = al lMachines & search = & action = search & macId = & country = all & selectedLanguage = 13 & type = all & page = 1 & ID = 71930 & DISO =-1 & driverLanguage = 42] and [3 G RF Power Control Utility | http://www.toshiba.eu/innovation/download_driver_details.jsp?service=EU&selCategory = 2 & selFamily = 4 & selSeries =] [243 & selProduct = 821 & selSho rtMod = 797 & language = 13 & selOS = all & selType = all & yearup load = & monthupload = & dayupload = & useDate = null & mode = al lMachines & search = & action = search & macId = & country = all & selectedLanguage = 13 & type = all & page = 1 & ID = 73658 & DISO =-1 & driverLanguage = 42] must be installed.