Set the rotation of the screen to external monitor on Portege M400

Similar Questions

• Tecra M7: Unable to set the screen resolution to 1680 x 1050 on external screen

  I have a M7 and a 1680 x 1050 VX2025 viewsonic monitor.
  I can't set the resolution for external display in clone mode or dual mode.
  Infact I can not get any resolution of the screen to exit the M7.

  I tried this in Windows XP and Vista with drivers from the toshiba Web site.

  Any ideas on how to force this resolution?

  Thank you

  Hello

  Are you sure that the graphics card supports this high resolution!
  If all goes well it s not a material limitation

  But especially if the display resolution is not available the graphics card driver does not support this resolution of the screen.
  In this case only the new driver installation and usage help

  What graphics card is installed on your laptop? Graphic chip Intel?
  If you use an Intel graphics card, then I recommend to visit the Intel page and search for a compatible driver on this page. Some users here in the forum said that the Intel drivers could help choose the preferred resolution.

• U100: Videos simultaneously on the screen and external beamer?

  Hello booklet users,.

  I don't have such a beautiful unit yet, but I think to get a. I guess I won't have too many problems with the screen and a small keyboard that I use a MDA Pro and I am very satisfied with the even smaller keyboard.

  But before you buy a Libretto U100 I really want to know if the book is able to show a video, which is included in a Power-Point presentation on the screen of the booklet as well as on a projector at the same time. Because this is not the case with my real Satellite phone, where I can run Power-Point presentations on both devices, but as soon as I start a video in the presentation, that it will only appear on my screen of Satellite.

  Thanks for sharing your experience,

  Walter

  Hello

  Usually on the satellite units, it should be possible to change the display devices with the FN + F5 key combination. So you can change the output to extern monitor/Beamer, TV, extended desktop display or you can clone display (laptop + monitor or laptop + TV).
  I put t know if you tried but check these possibilities.

  AFAIK the Libretto U100 also supports this utility and it should be possible to change the extended or video projector monitor output.

  Good bye

• How to activate the resolution wide screen to external monitor on Equium A60?

  Hello

  I had an Equium A60 with an ATI Radion 7000 mobility grahpics chip in it. Earlier the LCD is dead and has decided to use an external monitor rather than replace it. However, the external monitor is a monitor 22 '' widescreen computer does not provide a display suitable for resolution. Is it possible to update the graphics driver to provide the wide screen formats. I looked on the toshiba updates, but there is nothing new there, and ATI are not ready to support offer it on a laptop.

  Any ideas?

  Hello

  You can't choose your preferred resolution because the graphics driver does not support.
  Eventually the 3rd party driver support your favorite display resolution, but to be honest I wouldn't use these drivers because it could cause serious difficulties for laptop.
  The point is that these 3 third-party drivers are untested and not certified by Toshiba.
  Therefore, the use is at your own risk.

  Good bye

• How to set the screen resolution to insert content on monitor

  original title: content not fit screen

  the format is too big for the screen

  3 methods...

  1. set DPI:
  Right-click on a free space of the desktop > customize > column to the left, adjust the size of police (in PPP) > uac prompt > click default scale (96 DPI).

  2. resolution:
  Right-click on a free space of the desktop > Personalize > Display Setings > move the slider to adjust the resolution.
  Check your user manual, see if she tells you what resolution is for your
  computer.

  Here is a table of the guide line:

  
  

  3. do a system restore. Choose the date when your screen was in good
  size as your restore point.

  Start button > Search box, type system restore > press the Enter key > uac prompt > click on choose a different restore point > next > select dates as your restore point, until the click > next > finish
  To sit and wait. The machine restarts when it's done.

  Note: in case the images that appear on your screen are too large for you to implement the methods above, go in Mode safe and run these suggestions.

  Here's how to get safe mode:

  Shut down your computer > turn it back on and immediately and repeatedly press F8 key until you see a black and white screen. The top/down arrow and select Safe Mode

• How do I set the screen window size in a guest LinuxMint17 (WS7)?

  I am always on WorkStation 7 (last revision) because I discovered that after installing the update I bought I would be able to use 7 and I need that for some of my virtual machines...

  Anyway, now I need to test some features of Web server and need a KDE LinuxMint17 machine for this.

  Installation went well and I also installed the virtual machine; Tools of dishes without problem.

  As part of the installation, I put the size of the screen for the guest to 1024 x 768 in the properties of the VM.

  Then I could install the basic software that I need the terminal of the virtual machine.

  But it turns out that this screen is too small for the webbrowser, I need to run inside the guest, so I stopped and then replaced by the properties of the vm to display 1280 x 1024.

  The strange thing is that the guest does not adjust when I start again, it always appears in the size 1024 x 768.

  So I'm looking for help set the size of the screen correctly in the comments of LinuxMint17...

  Is it possible to make the largest screen in Linux?

  I looked at the System_Settings/Display_And_Monitor inside the guest, but I do not get a way to resize it.

  Or maybe there is way to allow resizing screen in VMWare Workstation settings for the prompt instead?

  Note that I have running in a window rather than the full screen because I use it as a test machine for stuff that happens in Windows...

  I tried Googling for Linux screen size settings but came empty-handed, suggestions addressed the other issues...

  I do not use Linux Mint but on other Linux Distros, I use the xrandr from a Terminal command to set the resolution of the screen when it is not available from the GUI.

  Execution of xrandr by itself will be out the available resolutions then, for example, use: xrandr-s 1024 x 768

• Closing lid with the result on external monitor black screen after that put 10.11.5 updated

  Already tried the PRAM reset and still does not, when I close the lid, the screen goes black. Before the update it worked perfectly.

  You meet ALL the requirements for the clamshell Mode?

• Setting the screen to get started on the applications rather than the Office of startup screen

  I have a HP Pavilion 23 and run Windows 8. Recently my pc has been commissioning on the desktop instead of starting up on the screen to start applications. How can I configure my pc so that when I turn on it goes to the start of applications screen and not desktop screen?

  Denver1003, welcome to the forum.

  You can go into control panel / taskbar and Navigation / Navigation / start screen / uncheck the first element ' when I connect or close all applications on a screen, go to desktop instead of the start.»  When it is disabled, the computer should start to the start of Metro (Apps) screen.

  Please, click on "Thumbs Up +" if I helped you and click "Accept as Solution" If your problem is resolved.

• Cannot set the screen stretched after playing game. HP Pavilion dv6000 Notebook.

  Hello

  Once a game my screen stayed tight, horizontally lying. Normally my screen is returned to normal after closing the game Rollercoaster Tycoon 3, but this time it somehow stuck or something. I checked the resolution: it's 1024 x 768 like it always was, so this isn't the problem. When I "Print screen", the image is quite normal on the other computers, so I think it may be the driver? Do I have to download Driver NVIDIA? I tried, but he says that the driver is not compatible with my hardware. I think I can find one that is compatible, but first I would like to know if this will fix my problem.

  Thank you

  DD

  I had a contact with HP customer service, and I tried many things. Restart the pc, download the drivers, nothing seems to work. The guy said I had to reinstall windows, and the screen was fine still... Here, there was a simpeler for this solution, but I'm glad that my screen is normal now.

• Setting the screen saver to display time

  On my old computer, I got the screen saver displays the time. I can't understand how do on my new computer.  Both have Windows XP.

  Hi Meki94,

  Simple, click Start-> settings-> Control Panel-> display-> screen saver-> select '3D text' in menu drop-down-> select settings-> Select time. Click ok on all screens.

  I hope this helps.

• set the screen time out

  Where is the calendar control from the Hibernate mode, the display on the screen?

  Hello

  see if that helps you

  http://www.Vistax64.com/tutorials/63567-power-options-sleep-mode-problems.html

• When I plug the second monitor, both screens go black - I can not change the settings for external monitor

  Help, please!

  Hello

  I suggest you to return the item and check if it helps.

   

  Solving the multiple monitor problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-multiple-monitor-problems

  You can also try lowering the resolution of the screen and check if it works.

  Change the screen resolution

  http://Windows.Microsoft.com/en-us/Windows-Vista/change-screen-resolution

  I hope this helps.

• How to set the screen resolution?

  Original title: on screen display with the unused space on the sides

  It is probably so basic, but my display is not full screen, even if I put it in full screen. There is an inch of space black unused screen on each side of the screen. What should I do?  Thanks in advance

  Hello

  You're probably not using the correct resolution, IE: you use a display standard aspect ratio when you have a widescreen monitor. This can be corrected in the settings/personalize/display of the Control Panel, adjust the slider to resolution here.

  Good luck, Rick Rogers, aka "Crazy" - Microsoft MVP http://mvp.support.microsoft.com Windows help - www.rickrogers.org

• Cannot bar resolution move to set the screen resolution

  I just installed vista and everything was huge! I went screen resolution under Customize and there is no other options on the scroll bar expect I am the one on which is 640 X 480 at an average of 16-bit color, I tried to update the drivers for the card and the screen but its still the same, I also reinstalled vista but its still the same HELP!

  Go to the Web site of the manufacturer of your laptop computer-graphics/computer card > drivers and downloads Section > key in your model number > look for the latest Vista drivers > download/install them.

  If there is no graphics Vista drivers available for your model, nothing can be done about it.

  Then:

  http://Windows.Microsoft.com/en-AU/Windows-Vista/change-screen-resolution

  Change the screen resolution

  Screen resolution refers to the clarity of the text and images on your screen. At higher resolutions, items appear sharper. They appear also smaller, so more items adapted to the screen. At lower resolutions, fewer items adapted to the screen, but they are larger and easier to see. At very low resolutions, however, images may have serrated edges.

  See you soon.

  Mick Murphy - Microsoft partner

• How to set the screen resolution to fit monitor

  original title: monitor

  I have a large screen, but it seems as if it was a waste of money because I don't get to use the middle of the screen. Can someone tell me please how to get full use out of my monitor? do I need some sort of version beta or something?

  Your description is not very clear, are the main steps to configure your display:

  -Make sure you have the latest drivers for your graphics card & monitor installed Windows 7 .

  -Search in the manual of your monitor and find out what the native resolution & refresh rate are for example (1920 x 1080 @ 60 Hz), then go to:

  Start-> Control Panel-> display

  and together that view you these settings.

  -If you have black borders around your screen, you should increase the size of your screen through the software installed normally with your graphics card. For a basic card ATI look for a feature called overscan/underscan. Look for the option to increase the size of the desktop in the nVidia Control Panel for nVidia cards. For othe graphics cards check support manual/website for advice.