Sharing physical storage with windows-server

Similar Questions

• HP Proliant ML350G6 with windows server 2008 standard 32-bit memory system installled is 22 gb but the physical memory is only show 4095 MB

  We are facing problems of physical memory to the hp Server model: HP Proliant ML350G6 with windows server 2008 standard 32-bit.
  The memory of the system installled is 22 gb but showing physical memory is 4095 MB only.pls give me the solution for this.

  * original title - NOT of the PHYSICAL MEMORY MONTRANT CORRECTLY *.

  According to this the max is 4 GB for this version and 32 GB for 64-bit. You need to install 64-bit

• ProLiant DL320e with Windows Server 2012 Bluescreen

  Hello

  I installed Windows Server R2 with smart supply a Proliant DL320e Server 2012 R2 and it bluescreens much. The blue screen message is a pretty no description "KERNEL_SECURITY_CHECK_FAILURE".

  I installed a second Proliant DL320e server and it shows the same behavior, so I conclude that this isn't a defective hardware.
  
  I found some knowledge which mentions screens blue and with the driver for Smart Array
  http://h20628.www2.HP.com/km-ext/content-webapp/document?docid=emr_na-c03793656 & DTD = default & local = d...
  But the update and version numbers do not match.

  Drivers, software and firmware for the HP DL320e Gen8 ProLinat Server Page did not all downloads for my OS-, but it displays a warning that it is experiencing problems.

  I tried to fill in the HP Support Assistant, but I got an email in response, telling me that they are currently unable to help with e-Mail support.

  The servers are offline on a clients site in a restricted environment so that they lack updates online.
  
  During this time, I downloaded the SPP Service Pack for Windows Server
  FTP://FTP.HP.com/pub/softlib2/software1/CD-generic/p652182553/v84427/SPPMDSLWIN2013090.2013_0830.7.i... and today, I'll try if it corrects the blue screens.
  
  Does anyone have pointers?

  Take care

  Martin

  Thank you, I have not found this forum. If an admin could move it which would be best.

  Just in case anyone else has this problem is this question:

  I contacted HP by telephone support and the solution is:

  Do not use smart supply when you configure your server, it is not supported and it will be randomly bluescreen with Windows Server R2 2012. You must install windows directly, so take your storage driver and copy it to a usb key and load the driver during the installation of windows. In my case I needed to use the mass storage drivers for Windows Server 2008 R2 from http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=5293151 & spf_p.tpst = swdMain & spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253DMTX_9b5424c852a54e49b501e280e5%257CswEnvOID%253D4064%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument & javax.portlet.begCacheTok = com.vignette.cachetoken & javax.portlet.endCacheTok = com.vignette.cachetoken

  Take care

  Martin

• Unabl eto manage my mail server using Alt - N Mdeamon Mailing software with windows server 2012 R2...

  Original title:

  Mail server

  Guys, I'm having trouble managing my mail server using Alt - N Mdeamon Mailing software with windows server 2012 R2...

  Can anyone suggest Me an alternative to that.

  Waiting for the answer

  Problems to go to the post office software company.

  Google for other e-mail programs.

• FoxPro9 is compatible with Windows Server 2008 R2 as operating system?

  FoxPro9 is compatible with Windows Server 2008 R2 as operating system?

  Try the FoxPro Forum

  http://social.msdn.Microsoft.com/forums/en-us/home?Forum=visualfoxprogeneral

  Don

• Cannot use RDP with Windows server 2008

  Original title: a user cannot RDP

  Hello

  I have a windows 2008 R2 server with 5 licenses of Terminal Server. I set it up so that users can RDP to the server using RDP and access other machines via VNC, it's not connetced to a domain or whatever it is.
  All users can connect using any OS - Win XP, Win 7, but a user cannot get to their place of work - I can connect from home, of Germany, etc. using the same user name and password, but they can get on the server but their access is denied.
  They can telnet to the IP address but can't.
   

  Hello

  Thanks for posting the question in the Microsoft Community!

   

  You have any question using RDP with Windows server 2008.

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the Forum TechNet site:

  http://social.technet.Microsoft.com/forums/en/category/w7itpro

   

  If you need any other assistance, let us know and we would be happy to help you.

• Able to access the folders but no shared drives on a Windows Server 2008 (C$, D$ etc.)

  I can access shared folders from a Windows Server 2008, but I am not able to access the shared drives (C$, D$). After entering my credentials, the system guard invites me for my credentials again and again. Any idea what can cause this?

  Appreciate the help

  Thanks.l

  Hello

  Your question of Windows 7 is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the Windows Server Forums on TechNet. Please post your question in the Windows Server Forums.

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer/

• HP Officejet 7500 has compatibility with Windows Server 2012R2

  Dear team,

  I would like to know if the HP Officejet 7500 a is compatible with Windows Server 2012R2 since there is no drivers for this OS.

  Thank you

  Mega-Support,

  Thanks for posting.

  Under Windows, you can connect a printer to a computer via USB and be able to print. However, since there is no software for it on the HP site it's all what you can. Unfortunately, you will only be able to print using the USB method.

• USB-cable series compatible with Windows Server 2008?

  Does anyone know if / what USB to serial cable drivers are compatible with Windows Server 2008?

  Hi CeeJayBrown,

  If the information provided by wb2001 don't help you, then you can your question republish Windows Server forums for assistance.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Dell PowerEdge R710 with windows server 2003 R2 is not start windows in normal mode.

  Hi Sir,

  Dell PowerEdge R710 with windows server 2003 R2 is not start windows in normal mode after upgrading the RAM to 64 GB.

  Arrangement of RAM is made 4 our 16 GB of RAM on 2 channels. I get no error message about the RAM configuration. It is booting in safe mode but not start in normal mode, his hanging during windows startup.

  Please give me guide to solve this problem.

  I thank & regards

  Ramanantsoa D

  Thanks for the reply.

  My version of windows is 32-bit Windows server 2003 Enterprise Edition Service Pack 2.

  Although I have not tried switching/EAP, I will try that and get back to you.

  And again something I have an idea of the installation of windows server 2008 R2 Standard version on this server, it will support? Please let me know Chris.

  Thank you.

• ACS any Version with Windows Server 2008 R2 64-bit domain controller

  Hi all

  Is there any version of ACS is currently working with Windows Server 2008 R2 domain controllers?

  Our server controls has recently upgraded domain controllers to 2008r2 and off 2003 servers. This did not our ACS 4.1.4 really happy.

  I read now serveral messages about problems with the ACS and Server 2008r2 and hope to find a solution (not to mention that switching to LDAP, yukk).

  Thank you

  Pato

  ACS currently cannot be installed on a server running Windows 2008 R2.

  As an alternative, you can install ACS on a member server.  Authentication

  ACS uses the local machine net API authentication both compared to a 2008

  R2 domain will work.  The Remote Agent can also be installed on a 2008 R2

  Server if you use devices.

  If you install ACS on a member instead server here is how to configure services

  to authenticate properly with the domain:

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.1/installation/guide/Windows/postin.html#wp1041304

  -Jesse

• "Application has stopped working" - in windows 7 double started with windows server 2003.

  I did a system to dual-boot with windows server 2003 and windows 7 both 32 bit.

  Server works well, but in windows 7, not a single application as 'MS office', 'Adobe Reader10', "mozzila FF 17', USB modem software etc. can be installed." Application has stopped working-check online for the solution, close the program "-l' display message."

  These applications have been executed successfully on the same windows 7 installed alone, stand not to dual-boot.

  As for example, in the case of Mozilla, I get the following details of problem:

  Signature of the problem:

  Problem event name: APPCRASH

  Name of the application: Installation of Firefox 17.0.1.exe

  Application version: 4.42.0.0

  Application timestamp: 5080c0b6

  Fault Module name: Firefox Setup 17.0.1.exe

  Fault Module Version: 4.42.0.0

  Timestamp of Module error: 5080c0b6

  Exception code: c0000005

  Exception offset: 00029000

  The system version: 6.1.7600.2.0.0.256.1

  Locale ID: 1033

  Additional information 1: c828

  More information 2: c8281d65ef26473d0d73e61539f36991

  3 more information: c4b2

  Additional information 4: c4b2e9bb96fe79d0a8d8b1d891ab6cf4

  These BONES are compatible?

  What is the solution?

  Help, please.

  Thank you...

  Hi Sounak,

  Thank you very much for the detailed information.

  You did changes to the computer before the show?

  The process of installing or uninstalling a program may fail for several reasons. This article describes the following issues (click on each question for corresponding resolution):

  Solve problems with programs that cannot be installed or uninstalled

  http://support.Microsoft.com/mats/Program_Install_and_Uninstall

  How to solve problems when you install or uninstall programs on a Windows computer

  http://support.Microsoft.com/kb/2438651

  Let us know the result.

• Oracle Database 11g - with Windows Server 2008 R2

  Hi all respected gurus!
  
  Recently I downloaded the Oracle 11 g - R2 database.
  
  Will it work with Windows Server 2008 R2?
  
  Please guid of the GEM.
  
  Thanks in advance.
  
  Mohammed Uzair
  Oracle applications developer
  Oracle APEX developer
  Pakistan
  + 92 (333) 7058754

  Yes, it does not work.

  What are the results when you do?

• CHM compatibility with Windows Server 2003

  I just finished creating the first version of a help with RoboHelp HTML CHM file, and it works fine on the machine, I used to write, as well as several others. When I tried the consultation on our production machine, running Windows Server 2003, I received the good Table of contents and Index, but all pages display the error "cannot display Page"standard. Right click on the page and selecting Properties said it had res://ieframe.dll/dnserrordiagoff_webOC.htm.
  
  I checked the specifications of RoboHelp, and indeed, the standard version of RoboHelp is not compatible with Windows Server 2003. However, I had assumed that this meant that I couldn't run the program on a Windows Server 2003-based computer, not that I couldn't run to the exit.
  
  This error is caused by a compatibility problem? It would help to upgrade to Server edition, or resign myself to use separate HTML files? Or is it another problem?

  Hi, Sydney, and welcome to the forum,

  The problem you described usually occurs when you view the contents of a file .chm remotely over a network and are due to security restrictions that Microsoft introduced in 2005. See this article for more information and workarounds:

  http://www.Grainge.org/pages/authoring/chm_mspatch/896358.htm

  So the solution is either to move files .chm on a local drive or to implement the registry changes that are described in the article (on your local computer and not on the Windows 2003 Server). The best way to make these registry changes is to use the free HHReg utility, which is available here:

  http://www.EC-software.com/products_hhreg.html

  To answer your question, however, I do not think that there is a difference between Windows Server 2003 and other versions of Windows as .chm files are concerned.

  Pete

• Performance issues with Windows Server 2008 host

  Hi all

  If I use a Windows Server 2008 host on my ESXi 4 installation.  I've recently upgraded to version 4 and had previously experienced similar problems and 3.5.  I also improved the hardware in the virtual computer to version 7 on all my guest OS.  The host in question is a file server.  Essentially what happens is sometimes that if a user opens a document (for most of the audio and/or video documents), the media file will take a minute or two to load then jump during playback.  If it's something like a file PDF/Word/Excel, the respective program crashes when the file loads or changes are saved, taking about a minute to respond to the user to enter again.  This problem is also very sparadic.  I even had this problem occurs when I'm the only user accessing the file server.  The specification of my VMware host is 3.2 GHz Xeon dual processor and 7 GB of RAM.  Two data warehouses are hosted on internal SATA hard drives.  ESXi is on the build 219382.  VMware tools is installed and update on all guest OS so far.  With regard to the use of the resources on the computer host, the memory usage with all my virtual machines running is almost always around 5.2 GB on the 7 available and the CPU usage is usually around 2 GHz.

  Looking at the logs performance monitor, I noticed an increase in the use of the disc during the shutdowns.  Are there utilities built to test the internal hard drives to find errors?  If this isn't the case, anyone recommend a utility that I can use to do this?

  Other ideas are also welcome.

  As mentioned disk SATA performance is less than ideal, or even acceptable by many people. The SATA drives in a configuration having non-RAID which makes it doubly Yes. If they were at least in a RAID 0, 0 + 1 or 5 configuration you would have best performance among readers (would be loath to 0 though, since there is no parity involved).

  Using the means on board mode SATA drive controller (or not RAID) of the SATA it runs the performance as low as possible.

  I wouldn't have even thought to have a server, or a system, used as a server that does not use RAID functions at least for redundancy. Couple that with discs that aren't going to cause bottlenecks as a standard too. Who used to refer to SCSI drives high speed, but also means using SAS drives these days (since they are replacing older parallel SCSI drives). The most difficult configurations for ESX, are performed on the server class hardware, which has access to a shared storage (which is high performance) on a fast network (Go to our days, or fiber) or a RAID array internally, which will not cause performance problems.

  You can try setting the server configuration, you have now, but that will only take you so far. You will need to the major weak links in the system. A (a major) is the SATA storage as stand-alone drives. The other is a network of 100 MB, which isn't too bad, but is still a performance hit when you share all traffic with these two ports. Moving to a GB switch could help the part of the question, but you will still have to solve problems of disk performance. If there is a decent amount of shared storage attached network where you are, see if they can give you a reasonable amount for the servers you are running on the host computer. Of course, you'll want to also be on the fastest possible network/connection of this storage.