SigmaTel HD Audio device will not work

Similar Questions

• Satellite L300-19F and WXP - audio device does not work

  Hello

  I installed Windows XP Home edition on my Satellite L300-19f after change SATA compatibility I installed Windows XP Home edition and installed all the drivers and everything's fine, but the audio device does not work. I downloaded the driver from DOWNLOAD & support center, but he can not detect.

  BTW: he used to work on Vista.
  What should I do?
  And thank you

  -Download driver audio Realtek HD Realtek page.
  -Go to the Device Manager
  -Remove the sound card.
  -Remove the High definition Audio Controller
  -Restart the laptop.
  -Reinstall the Realtek HD audio driver

• Satellite U400-17R - audio device does not work after installing XP

  Hello

  I bought a model U400-17R with Vista Home. I formatted and installed Windows XP Professional download drivers XP Toshiba site.

  Everything works, but my Sound Device does not work. When I check in the Manager of devices the Sound Drivers are there and it says working properly.

  I'm lost... Can someone please help?

  Hello

  I think you have the same problem like me a few months ago.
  I installed Win XP SP2

  The t is not his work because I didn't install the patches MS; KB835221 & KB888111

  The patches must be installed as a first step, before the audio driver is installed.
  If you have already installed the audio driver, then you must remove (uninstall) before install you the patches Ms.

  PS: The MS patches are part of the SP3

• Audio recording of Windows: the audio device does not work any

  I use a mobile Intel (R) Celeron (R) M with Microsoft WindowsXP Professional version 2002.

  The audio peripheral speakers do not work all of a sudden and there is no sound out put at all.

  But if I use Logitech and Microsoft HD camera mike and hear on Skype. But the speaker and mike does not otherwise for any other application.

  When I try it says there was a problem in the installation of this equipment:

  "The Conexant High definition Smartaudio HD2 - Code 18 is not installing.

  Reinstall the drivers for this device (Code 18)

  Could someone help me in the presentation how to solve this problem and help me to get the missing audio device installed.

  Thanks and greetings

  Srinivas Thompson

  Hello

  I suggest to follow the steps mentioned below and check if the problem persists.
   
  (a) click Start and select Control Panel, click on "Classic view" in the menu on the left.
  (b) double click on the "Device Manager"
  (c) expand "Sound, video and game controllers"
  (d) in the Properties dialog box of the device, on the driver tab, click set to update driver to start the Upgrade Wizard to update the material.
  Alternatively, you can uninstall the driver and then click Scan for hardware changes to reload the drivers.
   
  Also, follow the steps from the link below and check if that helps.
  How to troubleshoot sound problems in Windows XP

  http://support.Microsoft.com/kb/307918/en-GB

   
  Hope this information helps.

• I get a message that my audio device is not working. It worked fine the other day. Is it possible that something has been disabled?

  How can I check my audio device?

  Hello Charlotte T.

  Thank you for your message.  Nothing has changed recently to include the hardware, software or updates?  If your device has been working a few days previously, you can perform a system restore.  Click HERE for the system restore instructions.  Please let us know if it did or did not help to solve your problem.
  See you soon

  Engineer Jason Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.

• High definition Audio Device is not working... There is not its what so ever... even if everything is installed correctly

  Then, I used to have Windows Vista and I installed Windows 7... After that, the sound did not work at all... Although the pilot works fine... I tried eveything I can... I even thought that my internal speakers do not work so I went bought new and external speakers headphones, but niothing works... every time I play a song or something the sound bars are moving but thre is no sound... After searching the Web, I found out that the audio device should be set to speaker but I tried all possible ways no results... I downloaded several versions of the software realtek but no use... Please tell me what to do...

  Hello

  Have you tried to install the latest drivers for Vista, since there are not those of Windows 7?

  Check with support from Lenovo and their forums - in their forums, as there are other
  who have faced the same problem then maybe they can help.

  There may be no solution. Use all the methods described previously.

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• Audio device does not work on Satellite A300

  I have the new Satellite A300 for 3 days... and its not working. I have updated drivers and it did not help.

  I removed and installed again and it didn't work. I've tried everything. But when I look in Control Panel, everything is said to work, but it is not.
  And when I try to do an audio test it fails, error... and when I try to play music in media player it says: error. Does anyone have an idea, what the problem?

  > I have tried everything.
  Have you tried to install new OS by using recovery image Toshiba saved on the computer s portable HARD drive?
  And everything works well again. If you need instructions how to do this check please how Toshiba to the document under http://aps2.toshiba-tro.de/kb0/HTD9102IR0000R01.htm

  Good luck!

• Everyone knows the drivers of the device will not work after calling Camera.getCamera () so many times?

  Using Flash Player on Windows machines, since the Flash Player 11.4 version - Flash Player 15 (ActiveX version) and every version after that we had a problem in which Hauppauge PCIe and Videology cameras or other non-standard devices it does not work with Flash Player after calling getCamera() so many times. For example, we get the camera and publish a netstream for 10 minutes, then we have the camera set to null. Later, we call the camera again and after doing this 25 times or 100 times, the camera driver just seems to fail, and Flash Player is as is the streaming of the camera, but the NetStream info indicates zero-byte data video aired by indicating that there is no pixel coming from the camera.

  Someone else knows this problem to where you need to restart the browser or the Windows for Flash Player process power getCamera() properly again?

  Yes, it seems that others have experienced a similar problem. Adobe has not yet confirmed that it is a bug, but it is followed here:

  Bug #3850401 - handle with video.attachCamera leak leading to the unusable device

• Device will not work on VLAN

  Using a switch sg300-52, I created two VLAN that share a port of access to the internet. All features original, added to the VLAN work correctly and I therefore believe that them VLANS are configured correctly. I added a new office and an old laptop to the VLAN and none worked. I could get my computer to work by activating the VLAN tagging in the network card. The laptop is 5 years old and it doesn't have such a setting in the network card. There are 2 other devices that share the same port with the laptop and both work properly. My conclusion is that the laptop does not support tagging VLAN. Y at - it a way to configure the switch to account for this?

  Hi Thomas,

  I wonder if something as simple as an access-list (or filtering) will do what you want to do.  The only problem is that devices which must limit must have set the parameters IP. (or statically defined through DHCP)

  Here is an example of a list of acess that I took of my SF300 - 48P, note that the access list (ACLs) must be attached to a switch for monitor port or filter packetings in the coming switch to an IP host port.  In other words, the acl check matches the model, in the case below on the IP addresses on the infiltration in the switch port.

  Since the new release of firmware version 1.1, we now able to paste in an accessible via telnet, SSH or console (CLI) command line interface when the switch is in Setup mode. You can get into configuration mode by typing the command "config."

  Changes in the CLI are immediately reflected in the GUI.  If you do not the following access list, the last command could be 'write' save the configuration in the memory of switches.

  Note: If you are not comfortable with the use of the CLI to GUI to create the following lists of access and ACE and link the ACL to a switch port.

  I have in the example below, established a list of access to two ports, ports fastethernet1 and gigabitethernet1.

  Please note: ACL uses subnet reverse masking, which normally means, you must specify a specific IP host by the next note;

  192.168.20.5 255.255.255.255 with market back, this mask must be set as 192.168.20.5 0.0.0.0

  As a packet enters a port of a host IP switch, the access list is inspected from top to bottom, as soon as a match is found, the access list as you exit.  There is normally an implicit deny at the end of an access list, that's why my last statement in two access lists should allow any source IP address goes to any other destination IP wise the IP host might not get to the router WAN and Internet.

  The first IP address in the list below is the source IP and the mask and the second IP address is the destination IP address and the mask.

  room200 extended IP access list

  IP 192.168.20.62 enable 0.0.0.0 192.168.20.100 0.0.0.0

  IP 192.168.20.62 enable 0.0.0.0 192.168.20.63 0.0.0.0

  refuse the 192.168.20.62 ip 0.0.0.0 192.168.20.0 0.0.0.255

  allow an ip

  output

  The following applies to the access list for a switch port

  interface fastethernet1

  Service-acl input room200

  output

  room225 extended IP access list

  IP 192.168.20.63 enable 0.0.0.0 192.168.20.100 0.0.0.0

  IP 192.168.20.63 enable 0.0.0.0 192.168.20.62 0.0.0.0

  refuse the 192.168.20.63 ip 0.0.0.0 192.168.20.0 0.0.0.255

  allow an ip

  output

  The following applies to the access list for a switch port

  interface gigabitethernet1

  Service-acl input room225

  output

  It's the best way to contral access in this vlan and the filter will run at wire speed.

  Best regards, Dave

• My Celler mass storage device will not work on Windows 7

  I have a storage device mass of Celler that has always worked with several computers, now on Windows7 home premium 64-bit, that it says it can't find the drivers. I had Windows search for drivers, but the attempt failed. All solutions? It's most basic 2.0 mass storage device.

  Contact the manufacturer of the device on the drivers for it.

  The manufacturer has written drivers for their products, not Microsoft.

  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/default.aspx

  Windows 7 Hardware/Software Compatibility Center.

  http://www.SevenForums.com/tutorials/316-compatibility-mode.html

  How to run a program in Compatibility Mode in Windows 7 is at the link above.

  For any question on Windows 7:

  http://social.answers.Microsoft.com/forums/en-us/category/Windows7

  Link above is Windows 7 Forums.

  There is a list of the Windows 7 Forums at the link above to help you.

  You get the help you need there.

  You are in the Vista Forums.

  See you soon.

  Mick Murphy - Microsoft partner

• Wireless device does not work after downgrading from Windows 7 to Windows Vista.

  Original title: wireless device does not.

  recently, I got my os from windows 7 to vista, now my wireless device does not work. I checked the Device Manager and the report shows that my network controller driver is not installed and the modem on high definition audio bus device. I tried to install it, but in vain. What should I do?

  If your computer manufacturer does not have Windows Vista drivers available, you're probably out of luck.  Without drivers for these devices will not work.

  'spyc' wrote in the new message: * e-mail address is removed from the privacy... *

  recently, I got my os from windows 7 to vista, now my wireless device does not work. I checked the Device Manager and the report shows that my network controller driver is not installed and the modem on high definition audio bus device. I tried to install it, but in vain. What should I do?

• "The Audio Service is not working" - read a few other threads but without success

  Hello

  Thanks for any help I receive in advance,

  my sound was working perfectly last night, done a windows update and resolve now them audio custom work and cannot solve the problem with an automatic, the message I get is:

  Problems found: one or more audio device does not work currently not fixed

  Any help would be appreciated

  Hello!!! can you tell me you have a single machine windows7 or mutiple.

  I suggest two things here

  (1) try to copy and merge the audio of an another windows7 home premium or better service

  You can do this by going into the Registry Editor (make sure that the other computer is also a 32-bit system)

  HKLM/system/current control set/services/audiosrv click audiosrv and then on the file menu, select export and save the file to a USB key or drive.

  While copy on your machine and merge. Then restart your system.

  (2) you can try an upgrade on the spot with the windows7 dvd. Where you can repair the windows all without losing what.

  Thank you. :)

• Unable to Access Manager device and receive an error message saying "MMC will not work with a version of Internet Explorer prior to version 5.5.

  Original title: control Pasnel: Device Manager

  Trying to open Device Manager in Control Panel, I get the following error message:

  "MMC will not work with a version of Internet Explorer prior to version 5.5"

  OS Vista Home Premium 32 bit SP2

  There are conflicting answers on Google

  1 virus Infection. Recommendation: complete the recovery. I ran several anti-virus and anti-malware program that pretend that my system is clean.
  2. added Version 6.0.0.0 for a registry entry will produce a fix.

  The first suggestion that I consider as a last resort, but don't want to mess with my registry without help.

  Does anyone have experience of this 'mistake' and can talk me through a patch.

  Hello

  Please keep us updated.

  Glad to know that you have addressed the issue. Your efforts to solve this problem is appreciated. Please do not hesitate to answer, in the case where you are facing in the future other problems with Windows.

• CD\DVD will not work. Vista Home premium, 64-bit. Message says: Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39)

  I downloaded the drivers needed from the Dell site and the burner will not work. The computer was again in March 2009. Not sure where the drivers should be located. I downloaded on: win\syswow64\drivers\afc.sys. I've looked everywhere and tried to find a dialog box offering the option "update drivers" for this device. Could not find a way to do except Dell and that doesn't seem to work. The 64-bit system has no 'Device Manager' that I can find. When I look at the properties of the burner, the link to "find a solution" is not highlighted.

  Hello DanHenry,

  Try the miracle solution at this link: http://support.microsoft.com/kb/314060 but before you uninstall all third-party software (example: Nero, Roxio, iTunes). You can reinstall your software after you reboot your system. Please let us know if this helped you. Make it a great day!

  "In the end, the love you take, is equal to the Love You Make"

• I have a SimpleTech #96300-41001-170 standalone hard drive model. I can see it in printers & devices but will not work.

  * Original title: stand alone single Drive & WIN-7

  I have a model of disc hard SimpleTech #96300-41001-170 stand alone. I can see it in the devices & Printers. but will not work. It has been designed

  to work with Vista, XP & 2000. I am running Win - 7. Help, please!

  Thank you!

  Mike

  Hi Mike,.

  Thanks for posting your query in Microsoft Community.

  Since it has been designed to work with Vista, XP & 2000, it may not work in Windows 7 due to incompatibility problem. Therefore, I suggest you to visit the Web site of the manufacturer of the hard drive and download the driver available for the latest operating system.

  If the driver is not available for Windows 7, download the compatible driver for the previous version of Windows and I install it in compatibility mode.

  a. do the driver installation file right click and select Properties and then tap or click on the compatibility tab.

  b. check in the run this program in compatibility mode for: box.

  c. press or click the menu drop down and select a previous operating system, and then tap or click OK.

  d. try to install the driver and verify.

  Hope this information is useful. Please feel free to answer in the case where you are facing in the future other problems with Windows.