Signal and NI VISA Express - error-1073807202

Similar Questions

• Why do I get VISA code error-1073807202 when you try to connect the PXI-2565?

  I got the 1703807202 error code (a code library required by VISA is not found) every time when I start the computer and used 'Initialize with topology' first connect my channels.  This error could disappear if I start MAX and open devices and interfaces, then re - perform the same task.  How can I get rid of the error?  Thank you.

  My bad, GPIB driver has not been installed

• Tecra M9 - PCI Express Error at startup

  Hello everyone...

  I have a Toshiba Tecra M9 (PTM91E-04R03TEN)

  http://www.Toshiba.IE/innovation/JSP/supportMyProduct.do?service=IE#TAB0;

  Setting in motion,-wristwatch splach Toshiba and then "PCI Express error." screen on a black screen
  I can't get beyond this black screen
  and I can't get into the BIOS?

  Once that he managed to start completely, let him turn for a while I record information from the HARD drive. but then, the problem started again.

  In my view, that it is a problem with the nvidia GPU (in cycle Fatigue on the BGA) card
  I have the stripted computer laptop down... and bought ArctiClean thermal Pad, & Arctic Silver for "repair".

  Should I have someone analyze the material and find the troublemaker?... OR... should I just of reflow of the GPU.

  I'm technical interest... but not a PC / laptop technician: (..)
  any instructions on how to proceed would be received with gratitude...
  Can I just "bung it in the oven" and see how it goes? :) :) .

  Kind regards
  Peter

  Hello

  I found and read your other post regarding this problem and in my opinion the PCI Express error is related to a PCI device (i.e miniPCI module as WLan / Bluetooth, etc.) connected to the motherboard.

  Of course I can't say for certain that this question isn't related to a GPU malfunction.
  Usually, these details can be provided only by a technician who checked the laptop's hardware.

  Usually I put t recommend to disassemble the laptop. It s very difficult to perform this procedure and of course there is always a risk of damage part do such procedure without any instructions.

• VISA 1073807343 errors and 1073807202

  Hello everyone,

  I have several issues with the VISA 5.0.3 and LabVIEW 2010 SP1, and I don't know if or how they are related, so I'll post as much information as I have here. Please excuse the super post long, just trying to be thorough.

  Error BFFF009E (same as 1073807202 I think) appears to the MAX aperture as seen in attached ss1. When you try to open the VISA Interactive Control (IC), I get the message "failed to initialize the library VISA. The VISA interactive control utility will leave. "When I open any VI with a VISA resource and try to click the drop down arrow on the right to see the resources available, the arrow remains derpessed during a second, no field drop-down list is displayed, and then it returns to its original blank State. These problems all live together now, but before I could select BT VISA resources and use VISA IC, while I have always seen the error MAX.

  I tried to fix VISA, as well as VISA uninstall-reinstall 5.0.3 which I believe is the most recent version. No change. I also checked that visa32.dll exists as suggested in the article below. See systeminfo.txt attached to the installed software.

  http://digital.NI.com/public.nsf/allkb/1D1736BFD24A09878625742500241386

  This error seems to be related to an oscilloscope Tektronix DPO 2014 I connected via USB (or maybe something to do with TekVISA?). By this I mean that if the scope was connected when my computer started, this error occurs. When the field is not connected at startup, I don't see the same problems as above. Instead, I get...

  Error 1073807343 (BFFF0011) when you run a VI with a VISA resource to a serial device (see ss2), or connecting to the device in IC of VISA (see ss3). I also always see the error of BFFF009E to the MAX, but not the other problems on front. I can connect to these serial devices in hyperterminal and communicate very well here. Seems similar to the post below and also, I can't find visaconf.ini, but the solution does not apply as I LV 2010. In addition, ironically, I use VISA very well talk to the scope (whether to the MAX or LV) via USB if I connect after booting.

  http://forums.NI.com/T5/instrument-control-GPIB-serial/using-HP34401A-in-LabVIEW-yields-error-code-1...

  I use series of USB adapters made by Ultra (http://mail.ultraproducts.com/product_resources.php?cPath=35&pPath=782&productID=782 ) to go from instruments of series to my USB ports and the computer I'm unfortunately has no serial ports to be tested with, nor do I have another brand of the adapter. I know these converters can sometimes be a VISA problem, but I was certainly with it even without problem before.

  They that all seem to have intermittent problems, because I have seen both before as I have developed and pushed to go to strange as things exchanging (apparently identical) USB extension cables or restart a dozen times. This issue has been driving me crazy for weeks, I am looking for help to try to solve it finally.

  Thank you

  Ratti

  I think I got especially. Looks like it was TekVISA who got in the way, and if Visa32.dll was in the right place, it appeared (in properties > details) as the version of Tektronix, not the version of LabVIEW. After you have uninstalled all Tektronix as well as NI-VISA, he had disappeared, but no money to install or repair NI-VISA would be replaced by a version of LabVIEW Visa32.dll.

  However, with the help of the article from the link below, I discovered that the repair of the installation of the driver NI-VISA DURATION is what replaces Visa32.dll, as opposed to NO-VISA just as messages of error and other links seemed to suggest.

  http://digital.NI.com/public.nsf/allkb/B283196340462DFD86257633006DC799

  Now all the VISA stuff works again, except of course for the scope of Tektronix. I'll keep this battle for the future. Guess I just needed to talk to myself for a while.

  -Ratti

• Error-1073807202 lack of Code Library in open VISA

  Hello

  I'm trying to contact
  ANRITSU MS9710B via GPIB optical spectrum analyzer. Anritsu provides
  -Based VISAS screws for all functions. When you try to initialize the
  instrument (using VISA Open), I get the following error:
  -1073807202, which is "a code library required by VISA impossible.
  located or loaded.

  I can communicate with the
  using the measurement and Automation Explorer instrument and have
  recently installed the latest version of the NOR-488 driver (Version 2.2 for)
  GPIB-USB-B).

  I'm using Labview 8.0.

  Where can I find the missing code library?

  Thanks in advance!

  Freddy

  HM... Yes indeed! I had actually installed NI-VISA, but MAX indicates that it was not properly done. I'll get rid of and re - install the drivers of VISA,... that may well be it! I'll let you know... in the meantime:

  Thanks for your quick response!

• LM500 error-1073807202 old VISA Open in LM - 500 Initialize.vi - > Operate.vi LM-500

  Hi all

  I am new to using labVIEW and I would be really grateful if you could help me with an error.

  I'm trying to control a model LM-500 liquid cryogen level monitor (Discontinued).

  Its drivers are available online and I download and I'm launching the demo.

  When I try to run it I got the following error:

  code error-1073807202

  Former VISA Open in LM - 500 Initialize.vi-> Operate.vi LM-500

  The LM-500 is connected to my computer through RS232 serial.

  I don't know what could be the error. I would appreciate if you could give me an idea about it.

  These are the drivers:

  http://www.cryomagnetics.com/drivers/LM500LV6_1.zip

  Thank you very much for your help

  That's because the new VISA open does not recognize the IO senior class, you must remove and replace it with the new type. Right-click on the resource of visa > Create > control.

  Select the rigtht COM port and try again

• QOSMIO G40-114 and "PCI Express error"

  My G40-114 QOSMIOI worked perfectly until yesterday.

  I now have a black screen with the message "PCI Express error" at startup. Screen is frozen, can't do anything.
  What is the origin of this problem? (I searched the Web and looks like it has something to do with the motherboard...).

  Is that what I can do by myself?

  You can start your Qosmio laptop in SafeMode (F8 at startup)?

• Outlook express will not send or receive and givea an Ox800cccof error message

  Outlook express won't send or receive and gives an Ox800cccof error message

  Try to go to file | Identities and upward together a new identity and then add your email account it and see if it works.  If this is the case, then use a file | Import | Messages to bring them from the old identity.  See also www.oehelp.com/OETips.aspx#3 to ensure that you do not have interference with the delivery of your mail anti-virus.

  Steve

• My outlook express has stopped working and I get this error message, "the connection to the server has failed..." »

  My outlook express no longer works and I get this error: the connection to the server has failed. Account: 'pop-server', server: 'pop-server', Protocol: POP3, Port: 110, secure (SSL): no, Socket error: 10061, error number: 0x800CCC0E. Can someone tell what to do?

  Make sure that you can access your e-mail via webmail, if you have this option to ensure that it is not a problem on the server.  Then locate the antivirus interference and ensure that the analysis of the electronic mail is disabled (see www.oehelp.com/OETips.aspx#3).  Try to remove your e-mail account and then close OE and then add it back again and then see if it works.

  Steve

• Align the two signals and measure the Phase Shift

  Hello

  I do an experiment in which I use the NI USB-6221 DAQ card. The jury is able to make 250 k samples/second. I want to measure two voltages in a circuit and find the phase shift between them at frequencies between 1 and 10000. First I ouputted a wave sinusoidal frequency variable through the Commission and applied to a test circuit. Then I used the Board to measure the two tensions consecutively (thus reducing the maximum sampling frequency at 125 k). I used the signals align VI and measured the two phases and then calculates the phase shift (VI attached in Phase 1). It worked well for the test circuit I built in which the phase shift went way logarithmique.20 degrees ~84.5 degrees and then stabilized. At frequencies above 5 000 Hz phase shift must have remained constant, but it varies more or less 1 degree. When the phase shift is 84.5 degrees, present a degree of variability is not particularly explicit. When I asked my program on the circuit that I really wanted to measure, the phase shift went from-. 5 degrees up to about 1.2 degrees. The change in the values of phase shift at high frequencies (> 3000) was environ.2 degrees. Given the small phase shift, this variation is unacceptable. Now I tried to use a sequence to each blood individually (increase the maximum sampling frequency to 250 k) and then align the two signals and measure the phase of each shift. When I use align it and re - sample Express VI to realign the two signals, I get the message "error 20333 analysis: cannot align two waveforms with dt even if their samples are not clocked in phase." Is it possible to align two signals I describe here? I enclose the new VI as Phase 2

  Matthew,

  I think I have an idea for at least part of the problem.

  I took your program data and deleted stuff DAQ.  I have converted the Signal on the chart control and looked then what was going on with the signal analysis.

  The output of the Waveforms.vi line has two waveforms, like the entry.  However, arrays of Y in the two waveforms are empty!  It does not generate an error. After some head scratching, reading the help files and try things out, that's what I think is happening: the time t0 two input signals are 1,031 seconds apart. Since the wavefoms contains 1,000 seconds of data, there is no overlap and may not align them.

  I changed the t0 on two waveforms are the same, and it lines up.  The number of items in the tables is reduced by one. Then I increased the t0 of 0.1 seconds on the first element. The output had both greater than the entry by dt t0 t0 and the size of the arrays was 224998.  Reversing the t0 two elements shifts the phase in the opposite direction.

  What that tells me, is that you can not reliably align two waveforms which do not overlap.

  I suggest that you go to 2-channel data acquisition and that it accept the reduced sample rate.  You won't get the resolution you want, but you should be able to tell if something important happens.

  You may be able to improve the equivalent resolution by taking multiple steps with a slight phase shift. This is similar to the way that old oscilloscopes of sampling (analog) worked. Take a series of measures with the signal you are currently using.  The make enough average to minimize changes due to noise. Then pass the phase of the signal of excitement to an amount that is smaller than the resolution of phase of sampling rate and repeat the measurements.  Recall that I calculated that for a 5 kHz signal sampled at 125kHz, you get a sample every 14.4 degrees. If shift you the phase of 1 degree (to the point/mathematical simulation), you get a different set of samples for excitement.  They are always separated by 14.4 degrees.  Take another series of measures. Transfer phase another degree and repeat.  As long as your sampling clocks are stable enough so that frequency does not drift significantly (and it shouldn't with your equipment), you should be able to get near resolution of what you need.  The trade-off is that you need to perform more measurements and may need to keep track of the phase shifts between the various measures.

  Lynn

• Qosmio G40 - 10F won't boot up - PCI Express error

  I recently installed a windows update and the laptop came in restart mode.
  When the system boots it tries to start then I get a say black screen error PCI Express.

  I tried a system restore, but the disc does not start, also tried to access the bios and it does not work.

  Can I please ask for more help on this one because I don't have any problems at all, everything seems that a windows update has messed with my config in the bios.

  Help, please!

  Hello

  I can't believe that Windows update would affect the BIOS.

  In my opinion, this must be just bad luck.

  PCI Express error means generally that a PCI device on the motherboard has started to malfunction.

  This means that it could be a motherboard problem that could be solved by replacing the mobo

  Sorry man, but I think that you don't have a lot of options here... seems that Toshiba ASP technician should take a look at this question :(

• PCI Express Error - Qosmio G40 - 10Z

  Yesterday I turned on my laptop and I got a black screen with the message "PCI Express Error"
  I immediately started searching the Web that could be this error and I discovered that it is a known problem with some Toshiba laptops.

  http://www.nvidiadefect.com/Qosmio-PCI-Express-error-t383.html
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=49108
  http://www.nvidiadefect.com/Toshiba-Qosmio-G40-12C-t1149.html

  Some of the many topics that I found about this error.

  I bought my laptop model from January 2009 as a demo in a Dutch shop called Qplaza http://www.qplaza.nl/

  Don't think I have any warranty next to security,) I received store (2 years), but there are a few things I don't understand.

  As I understand it, it's that there is even a lawsuite on this problem and that it indeed was a problem with chips from nvidia 8600. But then why won't Toshiba or Nvidia fix laptops with these problems?

  I read my laptop have to go to the special repair service to replace my motherboard and I have to pay for myself.
  And that's IF they can fix my laptop.

  I started searching the Internet which could be the cost of price, but the answers don't make me a very happy woman :-(

  Is there another way to solve this problem?
  And are there not places where you can buy a very appropriate motherboard for this laptop?

  Can someone help me please? My laptop worked perfectly and without any warning... poof... can not run more.

  Hello

  I can understand that you are not happy with the current situation. Nobody is happy if the computer starts to malfunction, but it of not always easy to tell which is the reason. For the exact diagnosis, you need professional tools and these tools available only to an authorized service provider.

  I get bored in your ad information is information about the operating system. Are you using the version preinstalled Windows and you have already collected your notebook back to factory settings? If not, you should do this to make sure that it s no software or driver that is causing the problem.

  If it still doesn't work you should get in touch with an authorized service provider and talk with the guys what they can do for you. I m, they can make you an offer for spare parts if you need them and a good price too of course. Just talk to the technicians is that as possible. ;)

• Visa timeout error-1073807339 reading

  Hi all

  I'm doing a command autoscale on a DSO-A4034A Agilent (Keysight) connected by ethernet.

  But for some reason, I get a time-out error. When cheking to find system errors.

  I have set up the session visa in 'MAX' and use the name of the session of the instrument of the call in the VI.

  I founded these screws on the Agilent instrument driver. and I can do all the other stuff I have to do without errors. EMPLOYMENT INSURANCE. the installation type measures Aqusition read data and so on without error.

  The error is caused by reading order just after the ": SYSTEM: ERR?" command under the request of error VI.

  I have updated the firmware of the scope and upgrated 15.0.1 VISA but so far without success.

  There is no problem when I turn the "climax of the performance"...

  Is there someone who can give me some advice about where to look this anomaly? Any help would be gratefully recived.

  / Best regards Rasmus

  Rasmus.Olesen wrote:

  There is no problem when I turn the "climax of the performance"...

  Crying just "timing issue."  Add a little wait between ordering autoscale and error checking.  It is likely that the oscilloscope does not resemble incoming orders when he assures the autoscale.  If you wait for it to do the job.

• How do I get the analog input signal and send it to output analog (real time)

  Hello world

  I do a simple task in Visual C++ and I use PCI-6221(37 pin).

  Basically, I want to send the same signal of "analog input" to the "analog output".

  at the same time (or almost), to make real-time application.

  Can someone provide me with sample program please.

  I would be grateful if you could provide me with the great tutorial that explains

  step by step everything about NOR-DAQmx for C/C++ programming.

  Best regards

  Khassan

  This is my code in C++, you can optimize it if that seems too messy. This code reads the analog input signals and exports it through the analog outputs.

  To make this code additional work of the directories include and library directories must be added to OR.

  I hope it helps someone.

  #include
  #include
  #include "NIDAQmx.h".
  #include

  #define DAQmxErrChk (functionCall) {if (DAQmxFailed (error = (functionCall))) {goto error ;}}

  int main (int argc, char * argv [])
  {
  Int32 error = 0;
  TaskHandle taskHandleRead = 0, taskHandleWrite = 0;
  Read Int32 = 0;
  float64 context [1000];
  char errBuffRead [2048] = {'\0'};
  char errBuffWrite [2048] = {'\0'};
  bool32 done = 0;
  Int32 wrote;

  DAQmxErrChk (DAQmxCreateTask("",&taskHandleRead));
  DAQmxErrChk (DAQmxCreateAIVoltageChan(taskHandleRead,"Dev1/ai0","",DAQmx_Val_Cfg_Default,-10.0,10.0,DAQmx_Val_Volts,NULL));
  DAQmxErrChk (DAQmxCfgSampClkTiming(taskHandleRead,"",100.0,DAQmx_Val_Rising,DAQmx_Val_ContSamps,0));
  DAQmxErrChk (DAQmxCreateTask("",&taskHandleWrite));
  DAQmxErrChk (DAQmxCreateAOVoltageChan(taskHandleWrite,"Dev1/ao0","",-10.0,10.0,DAQmx_Val_Volts,NULL));
  DAQmxErrChk (DAQmxCfgSampClkTiming(taskHandleWrite,"ai/SampleClock",100.0,DAQmx_Val_Rising,DAQmx_Val_ContSamps,1000));

  DAQmxErrChk (DAQmxStartTask (taskHandleRead));
  DAQmxErrChk (DAQmxStartTask (taskHandleWrite));

  While (! fact &! _kbhit())

  {

  DAQmxErrChk (DAQmxReadAnalogF64(taskHandleRead,1,10,DAQmx_Val_GroupByScanNumber,dataRead,1000,&read,));

  DAQmxErrChk (DAQmxWriteAnalogF64(taskHandleWrite,read,0,10.0,DAQmx_Val_GroupByChannel,dataRead,&written,));

  }
  _getch();

  Error:
  If (DAQmxFailed (error))

  {
  DAQmxGetExtendedErrorInfo (errBuffRead, 2048);
  DAQmxGetExtendedErrorInfo (errBuffWrite, 2048);
  }
  If (taskHandleRead! = 0)

  {

  DAQmxStopTask (taskHandleRead);
  DAQmxClearTask (taskHandleRead);
  }
  If (taskHandleWrite! = 0)

  {

  DAQmxStopTask (taskHandleWrite);
  DAQmxClearTask (taskHandleWrite);
  }
  If {(DAQmxFailed (error))
  printf ("error DAQmx: %s\n",errBuffRead); ")
  printf ("error DAQmx: %s\n",errBuffWrite); ")
  }
  printf ("end of the program, press the Enter key to quit\n");
  GetChar ();
  return 0;
  }

• My emails are not sent and I get an error message - error 550 server windows live mail error ID 0x800ccc79.

  My emails are not sent and I get an error message - error 550 server windows live mail error ID 0x800ccc79.

  Your help would be greatly appreciated

  Thank you

  original title: network

  Hello GerryBenjamin,

  The best place to ask your question of Windows Live is inside Windows Live help forums. Experts specialize in all things, Windows Live, and would be delighted to help you with your questions. Please choose a product below to be redirected to the appropriate community:

  Windows Live Mail

  Windows Live Hotmail

  Windows Live Messenger

  Looking for a different product to Windows Live? Visit the home page Windows Live Help for the complete list of Windows Live forums to www.windowslivehelp.com.