Signal wireless connection impossible to find XP, Vista, Windows 7

Similar Questions

• Impossible to find all the windows of my contacts messenger on kinect

  I don't see all my windows live contacts on kinect

  Hello

  The question you have posted is related to Windows Live, and would be better suited in the Windows Live forum. Please visit the link below to find a community that will provide the support you want. http://windowslivehelp.com/

• Impossible to find or install windows essentials

  HP PAVILION LAPTOP

  G60T-200

  WINDOWS 7 32-BIT

  whenever I reboot I get ths message and then if I want to install it, I need a disc, which I did not.

  Want to find my YOUCAM, but hen can't find the installer of windows / windows security essentials.  I turned off all firewalls and security and programs ready to solve this problem

  message that I get when re start is

  Active support of HP

  C:\WINDOWS\INSTALLER\119a5f.msi

  other in the attempt to fix error messages:

  ERROR 1316A

  NETWORK ERROR

  FILEC; ACTIVE SUPPORT LIBRARY \WINDOWS INSTALLER\HP. MSI

  SETUP INSTALLSHIELD ERROR

  01FB4998-33C4-4431-85ED-079E3EEEE75D

  Have you tried to install Youcam from the link I gave earlier?

  Also, could you please give me the list of applications to start listed Statup tab by clicking Start, run, type "MSCONFIG" without the quotes and click on Startup tab.

• Wireless connect not identified Netwrok

  I have a Pavillion dv6 comes with Vista Home. It also came with the option to upgrade to Windows 7. I updated to Windows 7 and now I have no wireless connectivity. I have other laptops Windows 7, and each of them to connect successfully to the same router.

  He seems to find the router, but when I try to connect, it says "unidentified network". I don't have any problems wireless until the upgrade. The upgrade was made with HP supplied CD.

  I have disabled/endabled wireless adapter. Reset the router and the modem. Performance of virus may.

  I hesitate to make router changes since my other laptops connected successfully.

  Workaround.

  After you have applied all the advice without success, I started to disable all services unnecessary/addons/etc.

  Once I disabled the Digital Persona fingerpring I was able to get internet access.

• all-in-one 7510 loses the wireless connection

  We just bought a HP Photosmart 7510. She created fine with a wireless connection to our office for Vista 64-bit. After awhile, he loses the wireless connection. If I close the printer then turn on again, it resets the connection and works very well. I read that it can lose connection if it goes into sleep mode, and it seems that is what is happening. My question is, is there a way to keep the impression of loss of connection or enter the mode 'sleep'? Or do we have to put the printer only whenever we wanted to print, copy or scan? If so, the printer is adjustable to disable instead of switch mode 'sleep'?

  Already set to 'off '. I found this thread http://h30434.www3.hp.com/t5/Printer-Networking-and-Wireless/7510-photosmart-printer-energy-mode/m-p/1230681/highlight/true#M33814 I tried this and so far it works and has not lost its connection.

• Tecra A3: Wireless connection problem

  I reinstalled windows xp prof after my laptop crashed and lost files.
  Everything works except for the wireless connection, it is turned on, but windows will not see it?

  Any ideas? I tried to download different drivers from the driver from toshiba support page, but nothing has worked.

  Hello

  When the WLAN switch is set to ON, use the FN + F8 key combination to activate the WLAN adapter. After that do what you will be able to use the wireless network card.

  Wireless network card appears correctly in the Device Manager?

• How to install a windows wireless connection?

  I have a Dell with a dell wireless connection. I bought a cisco linksys e1500 modem works with a windows wireless connection. How to install a windows wireless connection?

  Hello

  -What exactly happens when you try to connect to the internet?
  -Do you get any error message or error code?
  To fix your problem, try the following methods one by one.
  
  Method 1: Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows
  
  Method 2: set up a wireless network
  http://www.Microsoft.com/athome/organization/wirelesssetup.aspx
  
  Alternatively, you can check the link for more information on this below.
  http://support.Microsoft.com/kb/313242
  
  Method 3: here is a link that gives you more information about the router E1500.
  http://homesupport.Cisco.com/en-us/support/routers/E1500
  
  I hope this information helps you!

• Wireless connection lost after update

  Last night I downloaded and installed the February Patch Tuesday updates from Microsoft on my WinXP netbook. When I rebooted the computer, wouldn't my wireless connection. My other computer of Windows XP (not yet updated) worked very well. I did a restore of the system on the netbook for just before the updates, and now my Internet is back. No idea of what happened and what I should do next? I would like to install the security updates... Thank you!

  Thanks for the suggestion, Halima. I don't even think to look here so far, as I never received an email informing me that I had a response. What I ended up doing after the restoration of the system is to reinstall two updates at once. And this time everything went well. I still have no idea why I lost my wireless connection, first.

  JO-Anne

• with WUSB600N wireless connection management

  I just installed a (renovated) WUSB600n on my netbook. The to-do bar displays 3 wireless connections, one is managed by the Wireless Linksys network monitor, and the other 2 are managed by Windows XP, each of these 2 shows a connection to a wireless (2.4 Ghz or 5 Ghz) bands. If I click on them and select view wireless networks, it says "Windows cannot configure this wireless connection".

  Can I disable Windows safely Login Manager?

  Thank you

  Thanks, I have already disabled the card wireless integrated into network connections and let me handle it the Linksys utility.

• Im trying to fill the network so my ps2 connections can use the signal wireless to my laptop running vista Basic. When I click to bridge, I get a message saying that I need at least 2 internet connections. is this in any way about this?

  Im trying to fill the network so my ps2 connections can use the signal wireless to my laptop running vista Basic. When I click to bridge, I get a message saying that I need at least 2 internet connections. is this in any way about this?

  Hi Jer9009,

  Welcome to the Microsoft answers site.

  ·         Could you give the exact error code or error number you get?

  To connect multiple computers, install a network adapter in each and run a network CAT5 cabling to connect each one to a hub (and thus the other.) The computer that will serve as a transition will have a standard network card for wired and a wireless network adapter that will connect to the wireless (WAP) access point or gateway on the second network.

  A network bridge is software or hardware that connects two networks or more so that they can communicate. You can create only a single bridge network on a computer, but a bridge can handle any number of network connections.

  For more information, see the link: create a network bridge:http://windows.microsoft.com/en-US/windows-vista/Create-a-network-bridge

  Add a connection to a network bridge: http://windows.microsoft.com/en-us/windows-vista/Add-a-connection-to-a-network-bridge

  Swathi B - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Vista SP2 wireless connection drops

  People, I know this question has been asked before, but I can't find a solution to my problem.  I've had my Dell laptop for about 6 months now and it worked perfectly, without any problem wireless connection.  On Sunday, August 9, I installed Vista SP2.  It updated no problem at all, but once he did his final reboot, it connected to my wireless router for about 5 minutes, then dropped connection.  Now, when you restart it only connects for a minute or two wireless then abandons connection.  I then uninstalled SP2 but it has not solved the problem with wireless.  My wireless adapter is an Atheros AR5007 and drivers are all up to date.

  Anyone know how I can fix this so that my wireless signal stay tuned as he used to pre SP2?
  Thank you.

  Hi KK_14,

  Thank you for visiting Windows Vista Microsoft answers forum.

  Fixing the problems of common networking in Vista:

  To reset the stack TCP/IP go to this article and either click on "Fix it for me" or follow the instructions to fix it yourself:

  http://support.Microsoft.com/kb/299357

  Disable the IP helpdesk:

  1 hold the Windows key and type R, type "services.msc" (without the quotes) and press enter

  2. scroll down to the IP assistance service, right-click on it and select Properties

  3. in the drop-down list box that says "Automatic" or "Manual", set it to disabled and then click 'apply '.

  4. then click on "Stop" to stop the service from running in the current session

  5. click on OK to exit the dialog box

  Disable IPv6:

  Try to uninstall IPv6 on all interfaces, the removal of virtual cards of IPv6 and reset the TCP/IP stack. To remove the IPv6, go to the properties for each network adapter, and deselect the check box next to the Protocol "Internet Protocol version 6 (TCP/IPv6), which will turn off, or select it and click on uninstall, which withdraw power off the computer.» Then go into Device Manager and remove any 4to6 adapters, adapters miniport WUN or tunnel adapters.

  NOTE: You should do this for each network connection.

  Disable the DHCP Broadcast Flag:

  Link: http://support.Microsoft.com/default.aspx/KB/928233

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  http://support.Microsoft.com/kb/322756/ (how to back up and restore the registry in Windows)

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers

  To resolve this issue, disable the DHCP BROADCAST flag in Windows Vista. To do this, follow these steps:

  Click Start, type regedit in the search box, and then click regedit in the list programs.

  If you are prompted for an administrator password or for confirmation, type your password, or click on continue.

  Locate and then click the following registry subkey:

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\ {GUID}

  This registry path, click the (GUID) subkey that corresponds to the card network that is connected to the network.

  On the Edit menu, point to new, and then click DWORD (32-bit) value.

  In the new area #1, type DhcpConnEnableBcastFlagToggle and press ENTER.

  Right-click DhcpConnEnableBcastFlagToggle, then click on modify.

  In the value data box, type 1 and then click OK.

  Close the registry editor.

  By setting this registry key to 1, Windows Vista's trying to get an IP address using the BROADCAST flag in DHCP Discover packets. If that fails, he will try to obtain an IP address without using the BROADCAST flag in DHCP Discover packets.

  Please let us know if it helps.

  Thank you and best regards,
  David

• Satellite P100-434: wireless connection with Vista problem

  Just bought this laptop with Vista and so far could not get the wireless to connect, I have 3 other computers and they will all connect, I have reset the router and set up new accounts on other computers without problem, but unable to do it on the P100.

  I tried the new RADAR feature and will not pick up all the networks, but by trying to establish a new connection it shows that a wireless network is available but it is nameless, although my network is named, I took the passkey of the network so that it is open but still does not connect, LAN via ethernet fine work.

  Wireless switch is on, but when I drag off switching wireless says WE

  Hello

  I can't give you an exactly the answer why you cannot connect to your WLan with Vista because there are so many options that should be checked.
  But I think that you will find the solution yourself with a little help from the Microsoft Web site.

  Please see this site:
  Connect to a network with Windows Vista wireless
  http://www.Microsoft.com/technet/community/columns/cableguy/cg0406.mspx

  You will find many useful tips, screenshots and Tips how to connect to WiFi with Vista.

  Please post again if you have found the key

• Qosmio G30-182: Drops Wlan connection & then cannot find wireless networks

  I use currently v.11.1.0.100 driver for Intel(r) Pro/Wireless 3945ABG, which is the last driver I found here at Toshiba.

  My problem is that I lose my wifi connection, randomly my home wlan (using WEP protection) and my University (WPA-Enterprise). After the connection drops, it is impossible to find all nodes wlan unless I reboot.

  Anyone have any suggestions on how to fix this? It is a bit frustrating to have to restart randomly because I need my network connection!

  It's OK, it s good to hear that a BIOS update solved your problem. :)

  Hope that this wireless broadcast could be resolved with the same procedure on other models of the machine.

  Welcome them

• I'm having a problem with my wireless connection. I have to keep in with zero wireless configuration to connect to the internet almost whenever I start the computer. I use downgrade XP on vista.

  I'm having a problem with my wireless connection. I have to keep in with zero wireless configuration to connect to the internet almost whenever I start the computer. Usually, you must configure only once and his game, but I have to keep on my new Dell Precision 6400 reconfigure it. I use downgrade XP on vista.

  Hi Susancav,

  Welcome to Microsoft Windows Forums!

  I'll be your message to the category of xp windows for a better answer. You can always find your message by going to my Threads in the section My Forum links at the top right of the page. http://www.Microsoft.com/windowsxp/expertzone/newsgroups.mspx

  Thank you and best regards,

  Bindu S - MICROSOFT SUPPORT
  Visit our Microsoft answers feedback Forum and let us know what you think.

• WRT54G good signal wireless but no internet connectivity.

  I have a WRT54G that has worked well for about a year. Last Sunday, I installed a couple of small updates from Microsoft on my main computer (cable via an ethernet cable from the router). At the same time, I installed service pack 3 on my girls (wireless) counter top.

  Since that time, on my three computers wireless I shows the strength of very good signal from the router but no internet connectivity. Internet works fine on the computer by cable.

  I have reset the router, no luck. Updated the firmware, no luck. Released and renewed until the cows came home and still no luck.

  I uninstalled the router of my main computer and reinstalled. During the installation it tells me that the router cannot find the internet even if the computer that works is connected through the router.

  I tried a different router (even part old version) which was a router to work when uninstalled about six months ago. I went through the installation process and it is the same, the router cannot find the internet.

  Is it possible to have two bad routers that the internet can pass through but the router cannot detect?

  At first I thought changing the setting of the Microsoft updates, but I restored my computer to a date before the updates and still have the same problem.

  Any help that anyone can give is most appreciated.

  Well there are some knows the problem with Service Pack 3 from Microsoft with wireless connectivity. You can uninstall SP3 from your computer and it will not solve the problem.