Simple note Wifi works do not, OK on cable

Similar Questions

• WiFi works but Ethernet does not work

  I just changed the ISP. I use the modem cable of the MRC, which is the same as one that uses Xfinity. I'm also using a Linkysys EA4500 router. I have not had any problems with setting up yesterday before they changed over this morning.

  I have two iMacs (my wife and I). If the modem cable is directly connect to one of the two iMacs, the internet works fine. However, when the Linksys router is part of the configuration, the iMac to my wife can connect via the Ethernet port but my iMac won't. My iMac can connect via WiFi. However, he won't be able to connect if I use an Ethernet cable.

  I have already reset the router to factory setting and restart the iMac and clear the PRAM, switched Ethernet cables. What happens here?

  The problem you describe will occur when changing the device connected to a modem cable without having to reboot the cable modem. Cable modems that are not as routers will communicate with a single device and refuse to connect to what anyone else, until you cycle power.

  Turn off your modem cable NCR and leave that it turned off. For reasons I don't understand (and will may not be not necessary), some cable ISPS also recommends disconnect physically their coaxial cable modem to perform a reset "full." During this time you can turn off the Linksys router also. Connect the iMacs to the router, either its LAN ports, via an Ethernet switch directly. It is not necessary to turn off Macs.

  Wait a few seconds, then reconnect the cable to the modem if you disconnected and turn on both the modem and the router. It should work.

• My MacBook is not connect to my Time Capsule to back up.  IMac my wife backup fine and our wifi works, but when I try to save, I get a message telling me to connect to the T. C. when it is available, which is never.  Help

  My MacBook Pro is not connect to my Time Capsule so it backs up.  IMac my wife backup fine and our wifi works, but when I try to save, I get a message telling me to connect to the T. C. when it is available, which is never.

  The problem started when I upgraded to Yosemite, sometimes back.  I am running 10.10.5.

  The MacBook Pro...

  Click the 'clock' Time machine at the top of the screen of the Mac

  Click Open Time Machine Preferences

  Click Add or remove from your drive

  Under the heading of backup disks, click on the drive it to highlight (probably named 'Data', unless you have changed the name of the drive)

  Click remove disk

  Close the windows

  Restart the MacBook Pro

  Click the 'clock' Time machine at the top of the screen of the Mac

  Click Open Time Machine Preferences

  Click select drive or Add or remove disks

  Choose the Time Capsule drive (probably named 'Data') by highlighting

  Click use the disk

  Close the windows

  Wait a while to see if a backup is performed

  If you want to manually run the backup, click on the Time Machine clock icon, and then click Backup now

  Report on your results. If the backup still does not work, we need the exact message that you see there.

• My iphone 6 has no service and always looking. WiFi works, sprint is not sure what is wrong with it. no damage ever to the phone. factory reset did not fix the it. Please advise?

  I need to know if I have a network problem or a hardware problem? My iphone 6 does not service and always looking, the wifi works. Phone has never been damaged. Sprint can't fix it, they think that its hardware problem. Factory reset did not work. Please advise?

  isoldier86 wrote:

  I need to know if I have a network problem or a hardware problem? My iphone 6 does not service and always looking, the wifi works. Phone has never been damaged. Sprint can't fix it, they think that its hardware problem. Factory reset did not work. Please advise?

  Get help with hardware features on your iPhone, iPad and iPod touch - Apple Support

• Satellite L40-15B - WiFi works at home but not at school

  My daughter has satellite worked at home and at school: wifi OK, internet OK. The satellite crashed: hard disk failure. Bought a new hard drive.

  I reset the Satellite via the recovery CD. It is now a new clean system with * Windows Vista home premium *. * Wifi works immediately at home. Internet too, but at school with my daughter, the wifi is NOT working anymore.*
  Laptops from other children at school always work with wifi.

  A college of my work told me his sister had exactly the same problem!

  Help!

  Hello

  If the WIFI connection works at home but not at school it has nothing to do with Toshiba. I think that your daughter should ask the administrator of the school what is the problem. Maybe the WLAN requires a certain configuration of TCP/IP or else I n t he know and I think that no one here can answer this question.

  Is that wireless network card is properly installed and works, because you can access the Internet at home.

  Sorry, but everything that s what I can say.

• HP laptop - 15-g221au: Hi, I am not able to connect to the internet. WiFi works do not.

  Hi, I am unable to connect to the internet. WiFi works do not. not able to find the right drivers for 32 bit win.7. need urgent help...

  You are the very welcome.

  You need these drivers wireless and bluetooth.  Registered as 64-bit but the 32-bit driver files are also included.

  Driver LAN wireless Broadcom

  File name: sp69014.exe

  Software and driver Broadcom Bluetooth 4.0

  File name: sp66402.exe

• My wifi works on windows 7, but it is not detected on windows 8

  Original title:

  Windows problem 8

  having powercars. My wifi works on windows 7, but it is not detected on windows 8 in my computer dell laptop. How to connect to wifi in windows 8. I tried Fn + F2 but it makes only bluetoth on and outside. I am not able to see too much on window 8 vertical icon bar. How can I connect to wifi on windos 8 too?

  Hi Yvon,.

  1. What is the model of your Dell laptop?
  2. What is the brand and model of the router?

  Adding to the suggestion of SilverBack_1 you can also refer to:

  http://Windows.Microsoft.com/en-in/Windows-8/cant-find-wireless-network

  You can consult the following links for more information.

  http://www.Dell.com/support/troubleshooting/us/en/19/KCS/KcsArticles/ArticleView?c=&l=&s=&docid=420860

  http://Windows.Microsoft.com/en-GB/Windows/network-connection-problem-help#network-problems=Windows-81&V1H=win81tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  I hope this helps. Please post with the State of the question.

• ADF simple security App works not

  I created a simple application to try to get a simple security scenario works, but I'm either missing something or there is a security bug.
  
  In my application, I have a user (user/password), an application role (BasicUserRole) and a page/taskflow (main page). I put in security as a result of the tutorial below. When I run the app, I am prompted with browser authentication dialog box. I enter the credentials (username/password), but authentication fails and I get redirected to the page "error 401 - Unathorized."
  
  I have attached my simple application. If please take and look and let me know if I did something wrong or if I hit a bug.
  
  Thank you
  Mike
  
  My sample application
  http://www.4shared.com/file/119388127/446c7d88/TestSecurity.html
  
  Tutorial that I'm following
  I'm looking at the section "Configure ADF security and create a user"
  http://www.Oracle.com/technology/products/jdev/11/cuecards111/adf_set_18/ccset18_ALL.html

  Hmm I downloaded your app and changed the password of your user named user account and ran the app and the page came fine. I used the user/eu1

• WiFi worked very well. Tried to connect the second device. "Wi - Fi auto-assignée 169.254.49.8 IP address and won't be able to connect... »

  One of our MacBook has been connected to the internet through our router base station Airport Express wireless and wifi worked very well. All of a sudden, the other MacBook could not connect. After a few days of no connection on one while the other worked, we rebooted the modem. Now neither laptop connects. We called our ISP and they verified that all is well with our internet service or the modem. Internet works fine with the cable plugged directly on each machine. Under network in system preferences, I get this message: "Wi - Fi 169.254.49.8 auto assigned IP address and won't be able to connect to the internet." When I run the diagnostic, I get a message saying that my network configuration has changed, but it has not changed anything. We have never gone and nothing changed since we first set up the modem and the AEBS. Any ideas on how to solve this problem?

  Yes, the express can do that... Suddenly lose the configuration and return to the bridge for example even when connected to a modem to bridge.

  The solution is simple... Press reset and redo the Express installation.

  NOTE... an Express is not expected that the main router... It's light to etc. of airprint, airplay wireless bridge. Don't wait to have no problems when you use the Express to do the work of the extreme or TC or another router should do.

• I just installed an airport extreme router and WiFi works, but the status light still flashes.

  I just installed an airport extreme router and WiFi works, but the status light still flashes.

  Open airport utility... Click EI... and see what the cause of the problem. It will give the list of questions on the summary page. Click on each of them and he will offer you even solutions.

  for example the firmware needs to be updated... nothing major... or DNS is wrong or double NAT...

  Without our crystal ball, we do not know what is the issue.

• Utilities airport shows a triangle Orange on Time Capsule, Wifi working

  Recently, my Time capsule is showing an orange triangle in AP-utility. By clicking on it, it shows the message: AP Time capsule found, with the possibility to forget.

  Time capsule shows a steady green light. Wifi is good job and my two other airports Express are being lit in the utility.

  I've read other discussions with similar problems. So, I did the following things:

  (1) soft reset of time capsule,

  (2) Changed link local IPv6 settings

  (3) disabled firewall

  (4) settings saved and restarted.

  It did not help for long after a few minutes the triangle orange has shown once again.

  In Time Machine, time capsule HD is not recognized or the other.

  But the wifi works perfectly.

  Please notify.

  I think that the problem is resolved.

  In this link, I found a solutionTime capsule will appear but the WIFI connection works

  He is working on 2 hours >.

• problem with WiFi connectivity with new Ipad Pro.  Unable to connect to the wifi at home.  My other devices (mini mac, iphone, iPad 2) all work fine on my wifi at home.  I am able to connect Ipad Pro wifi work.

  Problem with WiFi connectivity with new Ipad Pro.  Unable to connect to the wifi at home.  My other devices (mini mac, iphone, iPad 2) all work fine on my wifi at home.  I am able to connect Ipad Pro wifi work.

  On the Pro iPad, tap settings > general > reset > reset network settings

  You will need to re enter your Wi - Fi password.

  Then try to connect to your Wi - Fi network.

  If this does not help, more available in this support article suggestions > If your iPhone, iPad or iPod touch connects to a Wi-Fi network

• Unable to connect TC after modem swap, although wifi works very well.

  Time Warner Cable send me a new modem. (Technicolor)

  It is installed, enabled, and and the wifi works through my Time Capsule (1 TB 802.11n).

  But the TC blinks yellow and is no longer available on my iMac (Yosemite 10.10.3, 3.2 GHz Intel Core i3, 4 GB 1333 MHz DDR3)

  I restarted the mac, the modem and the TC, repeatedly.

  I have not tried a reset on the TC...

  It is installed, enabled, and and the wifi works through my Time Capsule (1 TB 802.11n).

  The last piece of this... WiFi works through my TC... sorry this is not possible.

  I have not tried a reset on the TC...

  Transport CANADA must be plugged in by ethernet on the main modem. If it's a router. Then the TC must be filled.

  But regardless of how it works you can not remove the ethernet of the TC.

  Transport CANADA should also create a wireless network and the Mac must connect directly to the TC otherwise on Yosemite or the BONES later, it will be more reliable and disappear from the network.

  So reset the TC... no files are lost and re-do the installation.

• Simple pass stopped working all of a sudden

  Simple passage no longer works, on my windows laptop 8.1 Envy 15 j009wm, suddendly today. HP Recovery Manager and tried to fix it, but it did not work. When I manually click Simple passage, it does not... ie the page starts to come, but then it flashes off and does not open. Any help's appreciated.

  Hi thank you Dragon-fur for your answer in a funny turn of events really just, I managed to do work again and was about to be updated with the steps I used to get the HP SimplePass to work again. If the steps I used to get the simple Pass to work:

  1. I uninstalled Malwarebytes.

  2. I used system restore to restore my system (after the system reset I still connect using SimplePass, but I couldn't use it online...) And I kept getting that wouldn't do anything

  

  3. I checked to see if the BiometricDevice has been activated (Control Panel, display by: small icons, Device Manager, right click biometric devices)

  4. I made sure that my BIOS, SimplePass and validity were updated (check the BIOS press F2 at startup... Select System Info, and look for the BIOS take note of the date and version; check SimplePass addressed to Windows (C, Program Files (x 86), HP SimplePass, made CheckUpdate, properties, details of the case... right click version; to check validity go to control panel, display by: small icons, devices, biometric devices, click Manager right validity sensors, properties, driver...) Driver version & date)

  5. I've updated validity sensors with an update on the drivers HP page

  6. I went to change PC settings and removed all recorded fingerprints

  7. I opened installation Simple passes fingers

  8. I reinstalled Malwarebytes...

• Can't tell if my WIFI works?

  I had to reinstall Vista (no surprise), but now I can't tell if my WIFI works.  The light on my laptop doesn't work anymore.  My daughter has a laptop and that she can get on her own and connect using the network I created previously, but I can't see this network or even find.  I think it's maybe the driver for the LAN card? But I do not know have tried several things.

  Help, please

  Go to the website of the manufacturer of your laptop > drivers and downloads Section > key in your model number > look for the latest Vista drivers > download/install them.

  The computer you are using now if you have an Internet connection with the other > download / save drivers > copy them into Flash Drive > transfer / install on the other laptop.

  See you soon.

  Mick Murphy - Microsoft partner

• I am very new to dream. I created a simple site that worked very well. I tried SEO booster and was checking on things different (for example Goigle webmaster). I don't know exactly what I did, but now when I type in my site it says the Palestinian Authori

  I am very new to dream. I created a simple site that worked very well. I tried SEO booster and was checking on things different (for example Goigle webmaster). I don't know exactly what I did, but now when I type in my site it tells me that the page cannot be opened because it was redirected too many times...? Help, please!

  Let me add some details to the choice in the scenarios you have for the use of domains.

  The areas are to simplify all kinds of activities on the Internet for users. Instead of addressing your email to go to the software from e-mail server to a computer with the IP 113.78.59.238 number, users can simply run their mail to "hannah" @ "gmail.com" or go to the website to "gildedgraces.com". This makes things a lot easier for users, but requires a little more difficult techniques backstage, because Internet computers connected and hardware (servers, tablets, phones, refrigerators) have only single numbers, not names. So, how internet needs to know which computer manages all emails for "@gildedgraces.com", and where physically this site 'www.gildedgraces.com '? This is where the "Domain Name Servers" kick in. They maintain long lists of these domain names, with references to the IP numbers correct and up-to-date. In this way, technicians can also easily Exchange computers, servers, connections, where a site is moved to another host, or when a server suddenly collapses. These things will happen, things have to change. They want to update certain IP numbers in the list on the DNS servers. I have it?

  So in order to get a Web site running, you know where your domain registry database is guarded and kept safe, and where your Web site is physically located.

  Note the difference between DNS (or servers) and the service (or Web servers) throughout all the instructions and documentation.

  Now, have a look at this PDF that was returned by Brad, in his response above.

  The domain name can be registered at any domain provider and the registry itself is not always need to reside there. You could relegate (you might say "move" or move) the registry for the DNS to another provider (like BC) service. In such a scenario, he must tell the provider holding the credentials of your registry, to redelegate it in British Colombia. That's what the article 4 in the PDF file. And of course, BC DNS service can internally so all applications for this field to their own web server.

  You can also choose to keep your current domain provider maintains the registry, but that their DNS servers before any request of this area on the web servers of British Colombia, where your site is published. This is typically a necessity for registrations from non-American, since many extensions of national domains (such as .nl and .de) can be recorded by suppliers outside of this nation. So the registry simply cannot be moved to an American company (it's a legal thing). In such a situation, article 6 of the PDF comes into play, describing what BC would normally internally: to the domains of the physical location of the Web site.