single network host does not

Similar Questions

• E3200: Network hosts does not work

  Hello.

  I just upgraded my firmware E3200: 1.0.04)is build 1 10 April 2012

  The guest network SSID has not shown before in my access point list, but now I can't even change the settings of the router.

  The options are grayed out.

  

  What's not here?

  After the upgrade you hard reset it router button of reset in the back for 30 seconds and then release.  Wait 10 seconds and cycle power to the router.  Now login and reconfigure.

• TAC +: TCP/IP open to 10.20.17.2/49 failed - connection has expired; remote host does not

  GANYMEDE + configured on the router and the router is in ACS.  I can ping from the ACS, but the router cannot establish a connection to authenticate users.

  AAA server Ganymede group + hq_acs-1

  Server 10.20.17.2

  Ganymede IP source-interface GigabitEthernet0/0

  !

  AAA authentication login default group Ganymede + local

  AAA authorization config-commands

  AAA authorization exec default group Ganymede + local

  AAA authorization commands by default group Ganymede + local 10

  AAA authorization commands 15 default group Ganymede + local

  nested AAA accounting

  AAA accounting newinfo periodic update 60

  AAA accounting auth-proxy default start-stop Ganymede group.

  AAA accounting exec default start-stop Ganymede group.

  orders accounting AAA 15 by default start-stop Ganymede group.

  AAA accounting network default start-stop Ganymede group.

  Default connection accounting AAA power Ganymede group.

  AAA accounting system default start-stop Ganymede group.

  AAA accounting resource by default start-stop Ganymede group.

  BigTree_3945 #sh ip int br

  Interface IP-Address OK? Method State Protocol

  GigabitEthernet0/0 10.4.3.1 YES NVRAM low low

  GigabitEthernet0/1 10.12.10.26 YES NVRAM up up

  Serial0/2/0 unassigned YES NVRAM low low

  Serial0/2/0.602 10.12.15.10 YES NVRAM low low

  11:08:13.673 Apr 13: MORE: Queuing AAA request authentication 79 for the treatment

  11:08:13.673 Apr 13: MORE: treatment demand beginning 79 authentication id

  11:08:13.675 Apr 13: MORE: authentication start package created for 79 (cisscdb)

  11:08:13.675 Apr 13: MORE: using the 10.20.17.2 Server

  11:08:13.675 Apr 13: HIGHER (0000004F) / 1BDD9C34/NB_WAIT/0: started 5 sec timeout

  11:08:18.676 Apr 13: HIGHER (0000004F) / 0/NB_WAIT/1BDD9C34: expired

  11:08:18.676 Apr 13: HIGHER (0000004F) / 1BDD9C34/NB_WAIT/0: expired, cleaning

  11:08:18.676 Apr 13: HIGHER (0000004F) / 0/1BDD9C34: the package of treatment response

  11:08:25.834 Apr 13: MORE: Queuing AAA request authentication 79 for the treatment

  11:08:25.834 Apr 13: MORE: treatment demand beginning 79 authentication id

  11:08:25.834 Apr 13: MORE: authentication start package created for 79 (cisscdb)

  11:08:25.834 Apr 13: MORE: using the 10.20.17.2 Server

  11:08:25.834 Apr 13: HIGHER (0000004F) / 1BDD9C34/NB_WAIT/0: started 5 sec timeout

  11:08:30.836 Apr 13: HIGHER (0000004F) / 0/NB_WAIT/1BDD9C34: expired

  11:08:30.836 Apr 13: HIGHER (0000004F) / 1BDD9C34/NB_WAIT/0: expired, cleaning

  11:08:30.836 Apr 13: HIGHER (0000004F) / 0/1BDD9C34: the package of treatment response

  11:08:43.689 Apr 13: TAC: using default Ganymede groups ' Ganymede"list."

  11:08:43.689 Apr 13: TAC +: opening TCP/IP 10.20.17.2/49 Timeout = 5

  11:08:51.057 Apr 13: MORE: Queuing AAA request authentication 79 for the treatment

  11:08:51.057 Apr 13: MORE: treatment demand beginning 79 authentication id

  11:08:51.057 Apr 13: MORE: authentication start package created for 79 (cisscdb)

  11:08:51.057 Apr 13: MORE: using the 10.20.17.2 Server

  11:08:51.057 Apr 13: HIGHER (0000004F) / 1BDD9C34/NB_WAIT/0: started 5 sec timeout

  11:08:54.692 Apr 13: TAC +: TCP/IP open to 10.20.17.2/49 failed - connection has expired; remote host does not

  11:08:54.692 Apr 13: MORE: Queuing AAA accounting request treatment 76

  11:08:54.692 Apr 13: MORE: treatment of the accounting application id 76

  11:08:54.692 Apr 13: MORE: sending AV task_id = 332

  11:08:54.692 Apr 13: MORE: sending AV timezone = EDT

  11:08:54.692 Apr 13: MORE: AV = shell shipping service

  11:08:54.692 Apr 13: MORE: sending AV start_time = 1334329734

  11:08:54.692 Apr 13: MORE: sending AV priv-lvl = 15

  11:08:54.692 Apr 13: MORE: sending AV cmd = show logging

  11:08:54.692 Apr 13: MORE: request for accounts created for 76 (n20j03t)

  11:08:54.692 Apr 13: MORE: using the 10.20.17.2 Server

  11:08:54.692 Apr 13: HIGHER (0000004C) / NB_WAIT/1/20FD90EC: started 5 sec timeout

  11:08:56.058 Apr 13: HIGHER (0000004F) / 0/NB_WAIT/1BDD9C34: expired

  11:08:56.058 Apr 13: HIGHER (0000004F) / 1BDD9C34/NB_WAIT/0: expired, cleaning

  11:08:56.058 Apr 13: HIGHER (0000004F) / 0/1BDD9C34: the package of treatment response

  11:08:59.693 Apr 13: HIGHER (0000004C) / NB_WAIT/1/20FD90EC: expired

  11:08:59.693 Apr 13: HIGHER (0000004C) / NB_WAIT/1/20FD90EC: expired, cleaning

  11:08:59.693 Apr 13: 1/HIGHER (0000004C) / 20FD90EC: the package of treatment response

  BigTree_3945 #.

  The AAA Client IP address	10.4.3. * 10.12.15.10
  Key
  Group of network devices	Test NJT AccessLink (Not assigned)
  Authenticate using	GANYMEDE + (Cisco IOS) RADIUS (Cisco Aironet) RADIUS (Cisco BBSM) RADIUS (Cisco IOS/PIX) RADIUS (Cisco VPN 3000) RADIUS (Cisco VPN 5000) RADIUS (IETF) RADIUS (Mount) RADIUS (Juniper) RADIUS (Nortel) RADIUS (Sepi)
  Connect GANYMEDE + single AAA Client (stop recording in accounting in case of failure).

  The 10.12.10. range * is listed under the HQ site.

  Your help is greatly appreciated.

  You said that you can ping the router ACS, have you tried the GigabitEthernet 0/0 interface packages (that is those THAT GANYMEDE + will attempt to use, given the configuration you have posted) supply?

  What is the network path between the router and look like ACS (IE, a firewall, NAT, etc.)?

  Can you connect to port 49 to the IP address of the router GBA, GigabitEthernet 0/0 of supply packages?

  Using VRF?

  Which version of IOS?

• in network bridge does not

  Hello

  I use VMware-player - 7.0.0 - 2305329, when I set up network bridge configuration to connect to the local host network, it does not connect and even its not throw errors in VMLog as well as in the event viewer.

  Local system configuration:

  Windows 8

  Intel core i3-3220 @3. 3 GHZ processor

  8 GB RAM

  Realtek PCIe GBE Family Controller version 8.21.909.2013

  Comment system configuration:

  Windows Server 2008 R2

  6 GB of Ram

  Here's what I tried to solve this problem.

  1. uninstalled and installed VMWare bridge Protocol in the local host network properties.

  2 uninstalled vmware player and all instances of the registry and the c drive and cleaned the system using registry cleaner, rebooted and installed the new version of VMware Player but still the same problem exists.

  3. reinstalled VMWare tools in guest operating system.

  So what you guys think about this problem, is it a solution?

  Thanks in advance,

  Bibiane.

  Hello

  I solved my problem by following this LINK .

  In fact, the problem was with the kaspersky antivirus (follow the link above) that was installed on my computer, here is the procedure I followed to make it work.

  1 uninstalled the kaspersky anti-virus.

  2 uninstalled VMware Player.

  3 reboot the system.

  4. installed in VMware Player back and make sure that the bridge network is working properly before installing Kaspersky return.

  5 reinstalled Kaspersky.

  and Voila Any return in the normal phase and my VM connects to the localhost network.

  Hope this helps someone.

  Kind regards

  Jung Lee.

• Wireless network adapter does not work on my Satellite A200

  Hello

  My wireless network adapter does not work under Vista. If I press FN + F8 nothing happens. Wireless communication is always offline.

  What can I do?

  Details:
  Typ: Atheros AR5008X Version: 7.2.0.164
  Laptop Satellite 200
  PSAE6E

  Please help me!
  Thanks in advance!

  Phil

  BIOS bug? I don t think so

  First of all, you must make sure that this isn't a hardware problem. In this case, insert the Toshiba Recovery CD and reinstall the operating system of this device. This will outline the laptop to factory settings. Notes; This would format the whole HARD drive.

  After the new installation, you must activate the WLan switch on the side of books, and you can then use the switch button FN + F8 to select the WiFi network.

  I assume that you have already configured your Wlan router. So the same settings such as the SSID, encryption of WLan, etc. must be defined on the laptop too.

• Network connection does not work after reinstalling Windows XP.

  Original title: problems with reinstalling XP.

  I had re format and re install windows xp but now my network connection does not work.  I have no IP address, even if my router and the pc are on DHCP. Device Manager tells me that the controller Ethrnet on the motherboard has no drivers, but I can't find a driver.  Any thoughts appreciated.

  Hi John Fisher_888,.

  You can download & install the drivers for the adapter from this link & check if it helps

  http://support.Dell.com/support/downloads/devices.aspx?c=us&l=en&s=Gen&SystemID=DIM_PNT_P4_8400&OS=WW1&OSL=en

  Hope the helps of information.
  Please post back and we do know.

• Update my wireless network device does not work after installation of Software Distribution Service 3.0

  After the installation of Software Distribution Service 3.0 update my wireless network camera does not work how do I uninstall Software Distribution Service 3.0

  How did you receive the update?

  Was it via Windows Update or Microsoft Update?

  Before the changes are made to your computer, the system restore points are made. This is so that you can go back in case an update causes problems.

  Follow these steps:

  1. click on the Start button

  2. click on accessories

  3. click on system tools

  4. click on system restore

  5. click on next

  6. in the calendar that appears, select the one which refers to Software Distribution Service 3.0 and click Next

  After the collection of certain data, the computer will restart, and the update will be gone.

  Hope this helps

  Post back if necessary

  ___________________________________________________________

  If this post can help solve your problem, please click the 'bookmark' or 'Yes' to this message button. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• I need help, its frustrating me! network discovery does not illuminate.

  my network discovery does not illuminate. Whenever I try to turn it on I get an error message that says: (the specified service does not exsist as an installed service)! I need to elp, its frustrating me! I have windows vista.

  Hello

  Did you change your computer?

  Method 1:

  Based on the network location you choose, Windows affects a State of network for network discovery and opens the Windows Firewall ports suitable for this State.

  Step 1: We recommend you to check if the elements of network discovery are enabled in Windows Firewall. To do this, try the following steps.
  1. click on start, type firewall and then click Windows Firewall with advanced security.
  2. click on rules of incoming traffic in the left pane and select the (SSDP-In) network discovery and network discovery (UPnP) - in the list.
  3. click on rules of outgoing traffic in the left pane and enable network discovery (SSDP-out) and the discovery of the network (UPnP-Out) in the list.
  4. apply the changes and check the result.

  For more information about network discovery, see this link:
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-is-network-discovery

  Step 2: Check the status of the following services: browser, TCP/IP NetBios support.
  1. Click Start, type services.msc and press to enter.
  2. from the list of services, double-click the service computer browser and TCP/IP NetBios support.
  3. change the startup type to automatic and start the service.
  4. apply the changes.

  Method 2:

  Now we go ahead and try to enable the discovery of the network on your computer and check for the issue.

  Network discovery is disabled by default for public networks. Changing a network location type to home or work is the best way to turn on network discovery. To learn how to change a network location type, see Choosing a network location. To enable discovery manually, follow the steps below.

  To turn on network discovery

  1. open the network and sharing Center by clicking the Start button, clicking Control Panel, clicking Network and Internet, and then click Network and sharing Center.

  2. If network discovery is off, click the arrow button expand the section, click turn on network discovery, and then click on apply. Need administrator permission if you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  I also suggest you turn on discovery of the network link and check.

  Enable or disable network discovery

  http://Windows.Microsoft.com/en-us/Windows-Vista/enable-or-disable-network-discovery

  See also:

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Network connection problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

• Catalyst Control Centre: host does not...

  I have a Toshiba PC running on a 32-bit system.  I got an error from the Catalyst Control Centre: host does not... No idea how I can fix this problem?

  Hello

  1. What is the full error message you get?

  2. What do you mean by the creation of guest account?

  You can see the following link for more information about the guest account:

  http://Windows.Microsoft.com/en-us/Windows7/what-is-a-guest-account

  3. you try to create a Standard user account?

  4. have you installed Antivirus software?

  You can see the following link to start your computer by using the safe mode startup options to see if the problem occurs in safe mode.

  Safe mode is an option of troubleshooting for Windows that starts your computer in a limited State. Only basic files and drivers needed to run Windows are started.

  The link below contains steps to start in safe mode:

  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  If you get the error message when you use MSN messenger, you must get in touch with Windows Live support for assistance

  http://windowslivehelp.com/forums.aspx?ProductID=2

  Hope this information is useful.

• Freecom network drive does not work in Windows 7

  My network of Freecom 400 Gb, LAN + USB 2.0 drive, works fine in Windows XP.

  After installation of the software (for XP) Windows 7 recognizes the drive (FND) in the network, but clicking on the drive reported an error.
  When you try to 'Add and remove mapped actions' drivers software the network drive does not.

  Unfortunately, Freecom doesn't give not any medium.

  On some forums, I found a 'solution' that did not work for me: Start - computer - Network\\FND\Public

  If anyone using a Freecom network drive has found a solution, it could make me very happy to cummunicate this for me.

  Johan Dulac

  Hello

  1. What is the exact model of the Freecom Network drive number?

  2. What is the full and exact error message?

  I suggest you to check if the drive is compatible Windows 7.

  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/default.aspx

  I would also refer the link for Freecom support:

  http://www.Freecom.com/support

  http://www.freecomforum.com/

• Network card does not properly

  I just bought a Windows 7 HP Pavilion HPE with an Atheros AR8161/8165 PCI - E Gigabit Ethernet Controller. When I restart the computer, the network adapter does not work, I check the driver updates and they indicate that the driver of the card has the updated version. What should I do next?

  Joe C.

  Hey Joe,

  We can refer to this article and check if that helps.

  Using the troubleshooter from network in Windows 7: http://windows.microsoft.com/en-US/windows7/Using-the-Network-troubleshooter-in-Windows-7

  Additional information.

  How can I troubleshoot network card? : http://windows.microsoft.com/en-US/windows7/fix-network-adapter-problems

  Thank you.

• 8600 visible on the network, but does not print wireless

  I can see the 8600 on my airport network, but does not display the work sent wireless (no error msg, stay in the queue). To print correctly if the USB cable is connected. Also see a separate network of 8600, but do not have a WEP key for it and don't see how to create one, so it won't let me join this network. Don't see any info on this in your pages and support forums.

  It was a very good question. I looked at my list of printer and there are 2 8600 s that are listed.  I think we could be active when the printer is connected via the cable and one for when it is wireless. I went by default and had no trouble in a wireless printing sheet.  It is probably a mistake on my part of the user, but I don't remember adding a second printer in the menu printing. I'll play around with it and remove an if it is not necessary. Thanks for your help.

• The network bridge does not

  I tried to create a network bridge between my LAN and wireless adapter, but my laptop ran out of battery halfway through. Now when I go to the properties of my wireless card it says that it is part of a network bridge. The problem is that the network bridge does not appear in the network sharing Center or when I run the map to see the command-line netsh bridge. I'm stuck now, unable to create a bridge or remove the ghost there wireless adapter seems to think it is. I have no restore point system to return to and am so stumped for ideas. Any help would be great.

  I have a Lenovo Z500 and had tried the troubleshooting that came with nothing.

  I was going to try reinstalling the driver, but before that I did decided to install the upgrade to Windows 8. 1. This seems to have fixed and I was able to create a network bridge that appears.

  Thanks for the help and the quick response

• Cannot migrate VM between 5.5 ESXi versions: the version of the product to the destination host does not support one or several CPU features

  We receive an error message that I am trying to make sense. I understand very well the notion of compatibility, CPU, CPUID, masking and so on, after working on a competitor hypervisor. However, this error seems wrong (or needs better wording) based on my understanding:

  Here is the message:

  ----

  A general error occurred: the version of the product to the destination host does not support one or several features of the CPU currently use by the virtual machine.

  Characteristics of CPUID level 0 x 1 'ecx' register are indicated with a '1' bit: x00x:xxx0:xx0x:x 000: x 0 11xx:00: 00xx:11xx

  ----

  
  

  This happened during the migration between two hosts ESXi with the same physical processors - in this case, a Westmere X 5650.

  
  

  The source host is on ESXi build 2068190 (5.5). The destination host is on ESXi build 1474528.

  
  

  The bits it seems to complain are:

  
  

  DTES64

  Monitor/MWait

  Cx16

  PDCM

  The punch line seems to be: "the product version of the destination host. However, I have trouble believing that support for these features have been added to ESXi between the two versions. If it were, VMware has been certainly silent about.

  For what it's worth, explicitly set us the CPUID masks in our virtual machines (no, CVS is not an option for us at this time.) This is the mask:

  CPUID.1.EAX = "00000000000000100000011001010001".

  CPUID.1.ECX = "00000010100110001110001000111111".

  CPUID.1.EDX = "10001111111010111111101111111111".

  CPUID.80000001.ECX = "00000000000000000000000000000001.

  CPUID.80000001.EDX = "00101000000100000000100000000000".

  cpuid.d.EAX = "00000000000000000000000000000000".

  cpuid.d.ECX = "00000000000000000000000000000000".

  cpuid.d.EDX = "00000000000000000000000000000000".

  Note that the bits of the message complains (2, 3, 14, 15) * are * in fact forced to '1' in our mask of cpuid.1.ecx. That means (if I understand correctly), ESXi does not have the virtual machine unless the host processor supports the feature. And in our case, the virtual machine will start with happiness on nodes, with both versions. It will be not simply migrate between them.

  So, long story short, is this a bug of ESXi? The error message is misleading? I understand something?

  Thank you

  
  Matt

  To use the masks feature VM in this way, you must replace all the 1 to your masks with-'s:

  CPUID.1.EAX = "00000000000000-000000 - 00-0 - 000-

  CPUID.1.ECX = "000000-0-00--000---000-000---".

  CPUID.1.EDX = '-000 - 0-0 - 0-

  CPUID.80000001.ECX = "0000000000000000000000000000000 -"

  CPUID.80000001.EDX = "00-0-000000-00000000-00000000000.

  cpuid.d.EAX = "00000000000000000000000000000000".

  cpuid.d.ECX = "00000000000000000000000000000000".

  cpuid.d.EDX = "00000000000000000000000000000000".

  Zeros erases the features that are not available on your hosts Westmere, and dashes will leave the other one features.  The problem with those masks was forced to you certain features on who would have normally been off.

• Host does not support configuring passthrough (DirectPath i/o)

  Hello

  I just installed ESXi 5.0 on a Fujitsu CELSIUS W350. http://support.TS.Fujitsu.com/UKFAQ/ProfessionalPC/Celsius/W3xx/W350.htm

  CPU: Intel Core 2 E6300 http://ark.intel.com/products/27248/Intel-Core2-Duo-Processor-E6300-(2M-Cache-1_86-GHz-1066-MHz-FSB)

  The CPU must be compatible with Intel Virtualization Technology (VT - x)

  As far as I can see that the "Intel Virtualization Technology" is also enabled in the BIOS, but I still just get the message "Host does not support configuring passthrough" under "Configuration-> advanced settings.

  I would like to have access to certain PCI cards in guest. Any ideas how to make this work? USB transfer works very well...

  Thank you!

  Welcome to the community,

  What to look for support DirectPath is ' Intel® Virtualization Technology for Directed i/o (VT-d).

  André