Site talk multihomed won't neighborships EIGRP on both lines

Hi all

This problem has been stripping my cabbage for about a week now. I have a lot of sites spoke on the seat. We have two routers in hub acting as primary and backup for all sites, a 13Mb SDSL and a 2 MB SDSL respectively. Exclusively use the GRE and IPSEC tunnels on (most) tunnels. All websites spoke (except one) are connecting using the standard ADSL.

I have a site that has a very bad connection to improve things for them, I try to use two ADSL connections and balance their.

To keep things simple, I try only to enable connections to our main router at this time and I do not use IPSEC, but either.

Here is the problem.

I get only a close relationship, forming a tunnel at the same time. If I stopped this tunnel, the other neighbor is shaping up and I can re - turn on the first tunnel, but it will not form a new neighbourhood.

The info that tells me more about what goes wrong is the following:

SH ip strategy nei

Neighbors of the EIGRP intellectual property for process 6001

H address Interface Hold Uptime SRTT RTO Q Seq

(s) (ms) NTC Num

1 172.20.64.1 Tu0 13 00:00:01 1 2000 2-0

0 172.20.65.1 Tu2 11 18:41:07 55 390 0 752649

The number of queue for the tunnel where the neighborhood is trying to shape and fault is always 2. No Hellos are received at the end. Hellos are received from the other end and, in fact, the neighborhood to do, but then it gets expired after receipt without Hellos. OTN goes to 5000 and then after the retry timer is sinking, the relationship fell, a new Hello is received and the relationship is recalculated. This causes my hell EIGRP as you can imagine.

Ive applied lists to distribute to the tunnels and tried to use static routes. I also tried statically assigning the neighbors with the neighbor command. No dice.

The two ADSL connections have the same IP next - hop to the ISP. This would prevent neighbors forming?

I downloaded the relevant parts of the config and the routing table also the router (cleaned). For completeness, Ive included all distribution-list commands that Ive tried but Ive used in combination and all together, as well as without them at all.

Your help will be greatly appreciated.

Your slow-going-mad network administrator,

Paul

Paul,

When you add these commands to key tunnel , could you at least check that the tunnels will work, i.e. were you able to ping to the opposite tunnel address?

I don't think that you can debug the EIGRP queue directly. You can debug are packages individual EIGRP, i.e. broadcasts of update, Ack, request, response, and EIGRP. It would be eigrp packets laconic retry to debug

If you're ready to make debugging more involved, I would suggest creating an ACL extended with entries of the corresponding permit GRE traffic between your router and the router of the headquarters in a sense is and EIGRP traffic on this tunnel and execution to debug the package ip N where N is the number of this ACL. Please note that if these GRE tunnels are currently all traffic beyond EIGRP, this debugging is not recommended because there is a LOT of output.

I wonder... is - this by all possible means that some of the addresses of the tunnel endpoint (i.e. tunnel source and tunnel destination) are advertised to EIGRP through these tunnels? This would cause a recursive routing entry, enough like the beat you are currently experiencing. How is the accessibility of endpoints tunnel completed in your routing table - is it via a default route? In order to foolproofness, I suggest you add static/32 routes for both routers (talks and head of bed) that contains the IP address of endpoint opposite tunnel, via the appropriate next hop.

Strange problem indeed!

Best regards

Peter

Tags: Cisco Network

Similar Questions

A Site at IOS IPSEC VPN and EIGRP

Hello

I have a connection of remote site to base via a VPN IPSEC router. I don't want to run EIGRP accoss VPN. Howerver I want adverstise the rest of the network from the router of core of the subnet to the remote site.

The remote VPN subnet is managed as a route connected on the router base?

Configuriguring a statement of network to the remote site on the router base will cause EIGRP announce the road?

You are right.

RRI (reverse Route Injection) is the correct way to announce remote routes as static routes on the HUB, and all what you need to do is redistribute static in EIGRP, so she is redistributed in your EIGRP.

Here is an example configuration:

http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00809d07de.shtml

(It's about OSPF and IPSec VPN dynamics, however, the concept is the same for ipsec site-to-site and redistribution in EIGRP)

Hope that helps.

Web sites and email won't recognize the 25 Firefox version. Sites to say I have an old version and ask for that update.

I have update my Fire Fox version 25 several months ago. I then started to receive messages from Web sites and my yahoo email account I was using an outdated version. Then, I updated to beta 26 and I still have the same problem. I am using Windows 7 on my PC. Never had any problems with Fire Fox until the 25 upgrade. I deleted the cache and cookies without effect. Should I uninstall Fire Fox and start all over again.

Before Firefox 4.0 a few extensions added stuff to the useragent which can make the AU stay stuck in this version. Your AU seems to be user Mozilla/5.0 (Windows; U; Windows NT 6.1; en-US; RV:1.9.2.16) Gecko/20110319 YFF35 Firefox/3.6.16 FBSMTWB

https://support.Mozilla.org/en-us/KB/websites-say-Firefox-outdated-or-incompatible#w_firefox-is-showing-the-wrong-user-agent

Firefox has stored an incorrect username for a web site. She won't forget him and corrects my entries as incorrect, preventing me to sign on the website

I incorrectly wrote the screen name. I wrote squidqueen instead of Squidqueen. Firefox remembers squidqueen and when I try to connect as Squidqueen it autocorrects to squidqueen (lower case s, rather than S capital). I erased the history and cookies and the cache of the browser. The part that I believe must be cleared is "form and search history" However, this line is grayed out and I can't mark it for delete.

Hi DebiAnn,

Try going to Tools > Options > Security and then click on the saved passwords. From there, you will be able to see all the sites that you have saved passwords for. You can remove this entry in the list and you should be good to go.

You should read the article from the Password Manager database for more information on this really powerful tool.

Hope this helps!

Is it my pc or the Web site? videos won't play

Newbie alert!
I use a 32-bit, XP Home, Google Chrome 8.0.552.237 and Adobe Flash Player 10.1.102.64.
You Tube and other sites work fine, but this site does not work for some reason any: http://www.renegadehealth.com/ghd/blog/native-diets-part-1/
I even tried Firefox, but no luck. Also, I tried to disable hardware acceleration and that no longer works.
Any other suggestions would be appreciated.
Thank you
tennisknight

Hi, thanks for the provision of information about your computer :-) It is always useful. From what you describe, looks like it's Web site.

Try using this link: http://renegadehealth.com/blog/ then find what you are looking for. The link you included I think is broken.

Hope that helps,

Thank you

eidnolb

I added a video on my site, but it won't play the whole thing? Does anyone have one imput on this?
I added a video on my site, but when I save me it and aynchronize it plays the movie. Does anyone have one imput on this?

Thank you.

D Sterling
I had this happen to me once for no apparent reason. I just downloaded the video file on the server again and that fixed it.

Glenn

MacBook Pro won't restart and has vertical lines that go down the scree.

Recently, my macbook pro to update so I rebooted. To do this, the computer turns on and starts the update but there are lines running down the screen. To about 1/4 of the way through, the screen turns gray, and then shuts down and restarts the process again. I ran a test of equipment and he came without any problem. Is there a way to fix this without going through Apple.

What model of MacBook Pro?

Maybe this problem.

http://www.Apple.com/support/MacBookPro-videoissues/

Apple Hardware Test is poor to find graphics issues.

This is the Office Mac Pro forum. I asked that your post be moved to the MacBook Pro laptop forum.

Why won't my email download both my laptop and my PC?

She uploads to one or the other, but not both

There are several types of messaging systems. It looks like you use POP (post office protocol) mail. This type of email is unsuitable for use on multiple computers. The usual mechanism is that messages are deleted from the e-mail server when the first computer downloads them. It is usually possible to define an email program to leave messages on the server, but your account will not be synchronized for messages sent among other issues.

Some, but not all, e-mail provide an IMAP email that synchronizes in full support. If your email provider supports this option, your e-mail accounts can be reconfigured for her.

Otherwise, webmail (access to your email via a web browser) is an option for the use of several computer.

VPN site to Site, as a part of the work of the ACL, why?

I built a VPN site-to site IPsec from A to B, I have about 10 different subnets in the traffice interesting ACL, now, I can get some subnets don't talk to each other, no problem, but some may not. For example, A to site B 10.1.0.1 subnet was not working, but 10.100.0.1 has functioned and 10.1.0.1 and 10.100.0.1 is actually two interfaces VLAN on a same router.

Debugging of the ICMP has shown, when A ping to 10.1 and 10.100, the firewall at site B receives pings of echo from site A and also the echo of ping time reply 10.1 recevived and 10,100, but only the firewall received echo response from the 10,100. looked like Firewall VPN B has no echo response 10.1 the site in some way

Config enabled on both sites several times, is unable to identify the problems and the incompatibility. 10.1.0.0/24 and 10.100.0.0/24 are two network objects in the same ACL.

The Super Cisco can provide some advice, what could go wrong, what I could use to troubleshoot...

Thank you very much.

PS everthing worked perfectly for a few days, then I had the problem of loss of package on the Web link, now the VPN tunnel is up, no config has been changed, but some just subnets not achieved through the VPN.

W.

Hello Yue,

WOW, that's weard.

Good thing is that now everything works now and believe me, it won't happen to you once again, you and I will know what to do next time... lol

If possible please brand of answering the question as to future users with the same problem will know what to do based on your experience.

Kind regards

Julio

What happens to my published site if I suspend my subscription to Muse?

If I make changes to my website created in Muse (but hosted externally) only once a year or so, can I pay just for a single month, make changes, and not renew?

Hello Belladonna,

I think I know what you're talking about. Say for example you buy a domain name, you pay a monthly subscription of 24.99 for Muse in may for the design and upload your site. You download your site, but you won't do to updates up to the Auutmn. You do not have to pay anything else until November, for example, when you decide to update again. You pay another 24.99 in November to do these updates. Nothing will happen to your site in the meantime, only one ' on your private domain. You only pay a right of 'access' to modify and adapt the site for 30 days per month in Muse. Think of it as renting software as you would for a DVD.

I compared it to a "Pay As You Go" mobile phone package. You 'buy' blocks of 30 months to the program when you need to make changes. It works for someone who just wants to make very few changes here and there over a year.

So yes, you can do exactly as you had described.

I get a failure of cookie on Old Navy and gap in particular sites.

I have the same message when I go to Old Navy and Gap. No other site. I did everything I can think of! Help! I don't understand why this site in particular won't let me store finds out anything!

This was driving me crazy for months. Today, that I solved it! I felt your pain, if I were to tell you how. Problem is I don't know which of the two things that I have tried has worked. (unfortunately, Microsoft's answer did not help.)

First of all, I've upgraded to Internet Explorer 8. I had to leave all of the add element ins, so he started with no. supplements, and I don't know if it of important or not. Then he gave me a few screen that says a supplement can be problematic, so I disabled that one.

Then I tried to get back to Gap/Old Navy. The screen that appears with the failure of cookie has a sign in the region. I signed in and took on the GAP site!

It's working now. Hope you solve yours also.

Nearby EIGRP falls on GRE tunnel

I have several users working at home with a router 871 a 2811 access in our offices. While most of these connections works without any problem, I have a few sites that continue to drop the EIGRP neighbor. Here is a sample of the log file

* Dec 17 06:32:48: % DUAL-5-NBRCHANGE: 10 IP-EIGRP (0): neighbor 172.29.1.49 (Tunnel1) is on the rise: new adjacency

* Dec 17 06:41:58: % DUAL-5-NBRCHANGE: 10 IP-EIGRP (0): neighbor 172.29.1.49 (Tunnel1) is falling: Farewell Interface received

* Dec 17 06:42:03: % DUAL-5-NBRCHANGE: 10 IP-EIGRP (0): neighbor 172.29.1.49 (Tunnel1) is on the rise: new adjacency

* Dec 17 06:43:41: % DUAL-5-NBRCHANGE: 10 IP-EIGRP (0): neighbor 172.29.1.49 (Tunnel1) is falling: Farewell Interface received

* Dec 17 06:43:46: % DUAL-5-NBRCHANGE: 10 IP-EIGRP (0): neighbor 172.29.1.49 (Tunnel1) is on the rise: new adjacency

* Dec 17 06:49:30: % DUAL-5-NBRCHANGE: 10 IP-EIGRP (0): neighbor 172.29.1.49 (Tunnel1) is falling: Farewell Interface received

* Dec 17 06:49:33: % DUAL-5-NBRCHANGE: 10 IP-EIGRP (0): neighbor 172.29.1.49 (Tunnel1) is on the rise: new adjacency

Does anyone have any ideas as to what may cause this problem?

Rick

Run us EIGRP GRE/IPSec tunnels to many remote routers. We have seen this problem of instability of EIGRP neighbor, more in some areas and less in others. Often one side removes the neighbor relationship and sends a 'goodby' neighbor. I guess it must if with packet loss drop some of the EIGRP Hello messages. We found that, by increasing the EIGRP timers, we reduced the frequency with which we see the problem (we use 15 and 45 rather than the value default 5 and 15).

HTH

Rick

Speaking of talk (VIGOR to CISCO) routing

Hi all

I have a problem with my config, it's a 7 rays star configuration. The address of the network hub is the 192.168.6.0.

I wish that sites spoke to communicate to other rays through the hub. The site talks are the routers of the force and the hub is a cisco 1842, the routing table is present on the vigors. I assume it's an ACL problem, but I've spent the last 3 hours trying figure this one and got no where, can anyone help?

I also nat has ports 80, 443, that work very well from outside the local network, but do not work inside? Anyone got any suggestions?

Thank you

Mark

192.168.6.0 HUB

192.168.18.0 TALK

192.168.23.0 TALK

192.168.28.0 SPEAKS

192.168.48.0 TALK

192.168.78.0 TALK

192.168.88.0 TALK

192.168.108.0 TALK

10.0.0.0 SPEAKS

Current configuration: 4558 bytes

!

version 12.4

horodateurs service debug datetime msec

Log service timestamps datetime msec

no password encryption service

!

BURTON hostname

!

boot-start-marker

boot-end-marker

!

enable secret 5 xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

activate the password xxxxxxxxxxxxxx

!

No aaa new-model

IP cef

!

!

property intellectual auth-proxy max-nodata-& 3

property intellectual admission max-nodata-& 3

!

!

name of the server IP 62.XX.x.2

name of the server IP 195.xxx.xxx.10

!

!

Crypto pki trustpoint TP-self-signed-692553461

enrollment selfsigned

name of the object cn = IOS - Self - signed - certificate - 692553461

revocation checking no

rsakeypair TP-self-signed-692553461

!

!

TP-self-signed-692553461 crypto pki certificate chain

certificate self-signed 01

308201A 5 A0030201 02020101 3082023C 300 D 0609 2A 864886 F70D0101 04050030

2 060355 04031325 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 30312E30

69666963 36393235 35333436 31301E17 313031 31323530 39353934 0D 6174652D

315A170D 2E302C06 1325494F 03550403 32303031 30313030 30303030 5A 303031

532D 5365 6C662D53 69676E65 4365 72746966 69636174 652 3639 32353533 642D

06092A 86 4886F70D 01010105 34363130 819F300D 0003818D 00308xxx 02818100

BA51CDF7 D418D270 7DCE516E 1ADE6DF5 82FE4507 CD1EBE0A 4B6E4B15 9A3C20ED

B1D19FC9 63D0B925 0A4611FF CE8D935C 264FC3FE DF8BFAC2 76EC38ED 68115F43

20A68D85 C04A564E 8BDE86FE 127F79B4 8E123D9C 8430940C BCD5CDA4 ADAAE387

FA1E14A6 ECF92197 0CF54E89 B33915E7 A4E01EC7 CE45DDF6 AA60D168 38C92E67

02030100 01A 36630 03551 D 13 64300F06 0101FF04 05300301 01FF3011 0603551D

11040A 30 08820642 5552544F 4E301F06 23 04183016 03551D 8014645E 3FDE4E90

A8773580 81EE4217 F4821238 993A301D 0603551D 0E041604 14645E3F DE4E90A8

77358081 EE4217F4 3A300D06 01040500 03818100 86F70D01 82123899 092A 8648

914EE910 C1EFCDB3 2C3B277B 45E4149F B8A78E94 94D6558F 7A1D5B45 D057DC02

1FCF0C28 5B29728B 9480E807 D7E7DF9E 751DD005 E108D94B 6B3FC03B 8EB1603B

9AF1E4CA 49067084 5B906C74 4D07217A 13FD0113 B721068A 3EC6C990 54101B4B

FC9860E4 3xxxB064 586EC91D EF7C5A8F 8BBF33C6 29BCF148 A7E2B987 F2A028F8

quit smoking

!

!

!

!

crypto ISAKMP policy 1

md5 hash

preshared authentication

Group 2

life 3600

!

crypto ISAKMP policy 5

BA 3des

md5 hash

preshared authentication

Group 2

ISAKMP crypto key xxxxxxxxxx address 77.xxx.xxx.176

ISAKMP crypto key xxxxxxxxxx address 85.xxx.xxx.85

ISAKMP crypto key xxxxxxxxxx address 85.xxx.xxx.9

ISAKMP crypto key xxxxxxxxxx address 85.xxx.xxx.81

ISAKMP crypto key xxxxxxxxxx address 85.xxx.xxx.228

ISAKMP crypto key xxxxxxxxxx address 85.xxx.xxx.153

ISAKMP crypto key xxxxxxxxxx address 85.xxx.xxx.10

ISAKMP crypto key xxxxxxxxxx address 85.xxx.xxx.61

!

!

Crypto ipsec transform-set esp-3des esp-sha-hmac 3DES-SHA

Crypto ipsec transform-set AES - SHA aes - esp esp-sha-hmac

Crypto ipsec transform-set compression-SHA-3DES esp-3des esp-hmac-sha-comp-lzs

Crypto ipsec transform-set AES-SHA-compression, hmac-sha-esp esp - aes comp-lzs

Crypto ipsec transform-set esp cm-transformset-1-esp-sha-hmac

Crypto ipsec transform-set esp - esp-sha-hmac this_should_work

!

card card-VPN-1 10 ipsec-isakmp crypto

the value of 77.xxx.xxx.176 peer

Set transform-set this_should_work

match the stores addresses

!

card crypto ipsec VPN - card - 1 isakmp 11

the value of 85.xxx.xxx.85 peer

Set transform-set this_should_work

match address dalby

!

card card-VPN-1 12 ipsec-isakmp crypto

the value of 85.xxx.xxx.9 peer

Set transform-set this_should_work

match address braintree

!

card card-VPN-1 13 ipsec-isakmp crypto

the value of 85.xxx.xxx.81 peer

Set transform-set this_should_work

match address corby

!

card card-VPN-1 14 ipsec-isakmp crypto

the value of 85.xxx.xxx.228 peer

Set transform-set this_should_work

match against glasgow

!

card card-VPN-1 15 ipsec-isakmp crypto

the value of 85.xxx.xxx.153 peer

Set transform-set this_should_work

match address hadleigh

!

card card-VPN-1 16 ipsec-isakmp crypto

the value of 85.xxx.xxx.10 peer

Set transform-set this_should_work

northwich match address

!

card card-VPN-1 17 ipsec-isakmp crypto

the value of 85.xxx.xxx.61 peer

Set transform-set this_should_work

match address wycombe

!

!

!

interface FastEthernet0/0

Description $ETH - LAN$

IP 192.168.6.40 255.255.255.0

IP nat inside

IP virtual-reassembly

automatic duplex

automatic speed

!

interface FastEthernet0/1

no ip address

Shutdown

automatic duplex

automatic speed

!

ATM0/0/0 interface

no ip address

no ip mroute-cache

No atm ilmi-keepalive

Bundle-enable

DSL-automatic operation mode

PVC 0/38

aal5mux encapsulation ppp Dialer

Dialer pool-member 1

!

!

ATM0/1/0 interface

no ip address

no ip mroute-cache

No atm ilmi-keepalive

Bundle-enable

DSL-automatic operation mode

PVC 0/38

aal5mux encapsulation ppp Dialer

Dialer pool-member 1

!

!

interface Dialer0

the negotiated IP address

NAT outside IP

IP virtual-reassembly

encapsulation ppp

Dialer pool 1

Dialer-Group 1

PPP reliable link

Authentication callin PPP chap Protocol

PPP chap hostname xxxxxxxxxxxxxxxxxxxxxxxxxxxxx

PPP chap password 0 xxxxxxxx

PPP ipcp dns request

reorganizes the PPP link

multilink PPP Panel

PPP multilink sliding 16 mru

period of PPP multilink fragment 10

Panel multilink PPP interleave

multiclass multilink PPP

card crypto card-VPN-1

!

IP forward-Protocol ND

IP route 0.0.0.0 0.0.0.0 Dialer0

!

IP http server

IP http secure server

overload of IP nat inside source list 100 interface Dialer0

!

corby extended IP access list

ip licensing 192.168.6.0 0.0.0.255 192.168.18.0 0.0.0.255

northwich extended IP access list

ip licensing 192.168.6.0 0.0.0.255 192.168.23.0 0.0.0.255

wycombe extended IP access list

ip licensing 192.168.6.0 0.0.0.255 192.168.28.0 0.0.0.255

hadleigh extended IP access list

ip licensing 192.168.6.0 0.0.0.255 192.168.48.0 0.0.0.255

extended IP access list stores

ip licensing 192.168.6.0 0.0.0.255 192.168.78.0 0.0.0.255

dalby extended IP access list

ip licensing 192.168.6.0 0.0.0.255 192.168.88.0 0.0.0.255

glasgow extended IP access list

ip licensing 192.168.6.0 0.0.0.255 192.168.108.0 0.0.0.255

braintree extended IP access list

ip licensing 192.168.6.0 0.0.0.255 10.0.0.0 0.0.0.255

IP Internet traffic inbound-ACL extended access list

permit any isakmp udp host 77.xxx.xxx.176 eq

allow a host 77.xxx.xxx.176 esp

permit any isakmp udp host 85.xxx.xxx.85 eq

allow a host 85.xxx.xxx.85 esp

permit any isakmp udp host 85.xxx.xxx.9 eq

allow a host 85.xxx.xxx.9 esp

permit any isakmp udp host 85.xxx.xxx.81 eq

allow a host 85.xxx.xxx.81 esp

permit any isakmp udp host 85.xxx.xxx.228 eq

allow a host 85.xxx.xxx.228 esp

permit any isakmp udp host 85.xxx.xxx.153 eq

allow a host 85.xxx.xxx.153 esp

permit any isakmp udp host 85.xxx.xxx.10 eq

allow a host 85.xxx.xxx.10 esp

permit any isakmp udp host 85.xxx.xxx.61 eq

allow a host 85.xxx.xxx.61 esp

!

access-list 100 deny ip 192.168.6.0 0.0.0.255 192.168.78.0 0.0.0.255

access-list 100 deny ip 192.168.6.0 0.0.0.255 192.168.88.0 0.0.0.255

access-list 100 deny ip 192.168.6.0 0.0.0.255 10.0.0.0 0.0.0.255

access-list 100 deny ip 192.168.6.0 0.0.0.255 192.168.18.0 0.0.0.255

access-list 100 deny ip 192.168.6.0 0.0.0.255 192.168.48.0 0.0.0.255

access-list 100 deny ip 192.168.6.0 0.0.0.255 192.168.23.0 0.0.0.255

access-list 100 deny ip 192.168.6.0 0.0.0.255 192.168.28.0 0.0.0.255

access-list 100 deny ip 192.168.6.0 0.0.0.255 192.168.108.0 0.0.0.255

access-list 100 permit ip 192.168.6.0 0.0.0.255 any

Dialer-list 1 ip protocol allow

public RO SNMP-server community

!

!

control plan

!

!

Line con 0

line to 0

line vty 0 4

password: xxxxxxxxxxxxxxx

opening of session

!

Scheduler allocate 20000 1000

end

Also check this important Information on Vigor holding ipsec his.

https://supportforums.Cisco.com/thread/257320?decorator=print&displayFullThread=true

Manish

Synchronization of the settings for the Site (Manager)

I use Dreamweaver on two different PCs. I use the same Adobe ID on each computer (that is, I see my email address in the Edit menu).
On both computers, I have the edition > Preferences > sync configured to allow automatic synchronization settings and I chose the five categories for the synchronization (for example, Application, Site, extracts, etc.).
I'm trying to 'move' all my settings from computer A to computer B. On computer A, I select Edit > [email protected] > sync settings. On computer B, I tried using the same command to synchronize the settings. I also tried Edit > [email protected] > manage the synchronization settings, select the check box to import the sync settings (which says that the cloud settings will be imported on the next launch) and restart Dreamweaver. However, the extracted component does not contain my snippets on computer B, my named workspace is not in the list of workspaces, it is not all of the sites listed in the dialog box Manage Sites, etc.

Thanks for your advice.

First, the Site synchronization synchronizes only parameters associated with a site. He won't move a site from computer A to computer B. The reason is that Adobe does not store your usernames and passwords as part of the synchronization. Complete documentation on what does the synchronization and its limits is here: synchronize site settings, preferences, keyboard shortcuts, and workspaces in the Dreamweaver forums

For other parameters, I try to go in sync settings in the preferences and click on manage account (on computer A). So on this Web page, go to the settings for Dreamweaver and select Reset settings. When you do that, you will need to go to A computer and download a new synchronization. It could just be something doesn't work is not on the end of Adobe. If this does not work, we go further.

Acrobat requires a qualifying series upgrade, but it won't accept it

I have a new computer and want to install Acrobat XI on this subject. It loaded on the computer, but when I try to start the program, he said I had a serial number but that I needed a series of upgrade, qualification, so I put in the serial for my 9 version, (that I got on the Adobe site), but it won't accept it. What should I do?

Contact Adobe technical support via chat and explain your problem. They may be able to see something in your account or the version you had for you help through activation.

To the link below, click on the still need help? the option in the blue box below and choose the option to chat...

Serial number and activation support (non - CC) chat
http://helpx.Adobe.com/x-productkb/global/Service1.html ( http://adobe.ly/1aYjbSC )

Site talk multihomed won't neighborships EIGRP on both lines

Similar Questions

Maybe you are looking for