SlideNav, energy management, and! KeyStudio does not

Similar Questions

• Blue indicator of Win 7 circle network ALSO hang Device Manager and MSE does not

  I have a strange problem since the recent windows updates.

  Indicator of network in the bar tasks displays a blue circle for about 20 minutes after I start the computer. During this time I can't run regedit, I can't open the Device Manager, and I can't seem to activate the protection in real time to Microsoft Security databases. However all the time I have internet and network access.
  After about 20 minutes the light will come back normal (sometimes it goes through a Red Cross first), date at which the computer then runs everything normally, if I have my phone on, I get the auto run screen, Device Manager works and I can also start MSE.
  It's as if the computer is waiting for something to happen. Device problem? However, all devices appear to work normally.
  The latest updates, I made were optional for monitor HP and Microsoft mouse and a keyboard, both of which work well in the era of 'blue circle '.
  I also tried updating the adapter software.
  It is not important, but it's annoying!

  Hi Carmen,.

  The blue circle on the network icon indicates that the system is looking for a network connection.

  If it appears at the start, then start the modem and the router before you start the computer.

  Method 1:

  Using the troubleshooter from network in Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  Method 2:

  Step 1:

  Check if the problem persists in safe mode with network.

  Check out the link:

  Startup options (including safe mode)

  http://Windows.Microsoft.com/is-is/Windows7/advanced-startup-options-including-safe-mode

  Step 2:

  If the issue is not still in safe mode, and then start the clean boot computer to determine if a third-party program is causing the problem. To configure your computer to clean boot see the following link.

  How to perform a clean boot for a problem in Windows Vista, Windows 7 or Windows 8
  http://support.Microsoft.com/kb/929135

  Note: See "How to reset the computer to start as usual after a clean boot troubleshooting" under more information to prepare the computer to start as usual after a repair.

  Also check the link for more information:

  Slow PC? Optimize your computer for peak performance

  http://www.Microsoft.com/en-in/athome/Setup/optimize.aspx#fBid=_dBb8lcqecd

  Important: When running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.

  Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

  I hope this helps. If you have any other queries/issues related to Windows, write us and we will be happy to help you further.

• adater WLAN and bluetooth does not properly on windows7 32 bit hp 250

  I need driver wireless adater aid, after installing windows7 32 bit on my new laptop HP 250 G1 my wireless network does not yet and infact is not visible in the Device Manager and theblutoothalso does not work correctly. is the network controller hardware id: PCI\VEN_168C & DEV_0036 & SUBSYS_217F103C & REV_01

  Finally, my BIOS, wlan id is: ppd-qcwb335 on hold using the driver get my wlan and bluetooth back to life!

  Thank you!

  Series of QCA9000 of Qualcomm, Atheros Wireless LAN Driver for Microsoft Windows:

  http://ftp.HP.com/pub/SoftPaq/sp64501-65000/sp64676.exe

  To help you with your bluetooth driver, I need your bluetooth hardware ID.

• in Device Manager... COM and LPT does not appear

  When I go to the Device Manager and try to change the com port settings or change a com port, com and lpt does not appear.  This is a brand new hp 630 and I installed an edgeport adapter.  I need to be able to change the com ports from time to time.  How do I do so com and lpt is not or how com and lpt to appear in Device Manager?

  Hello

  You can follow the steps in the link and check if the problem occurs:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-hardware/ports-not-listed-in-Device-Manager/f5e1dabe-df1c-4262-A912-688c40f75ddd

• I downloaded the new tools tab of 2011 and it does not appear in Firefox c. 40.0.2

  'Ask.com' guard replace my new choice of tab and 'ask.com' (and 'request') does not come under the extensions, modules, plugins, or even on my computer. I tried every fix offered by Mozilla and Microsoft without success. Today, I found and installed the new tab add-on tools, and it does not, even after restarting Firefox.

  Help please remove ask.com as my new tab page!

  Hi, 'Application' must be there somewhere, please try through Remove Ask Toolbar and Ask.com Search (uninstall Guide) by the Councils of Malware.

  Note that not all programs removal allows to detect all malware, you may need to run multiple or all of them.

  After the removal you may need to reset your new tab, search etc, what you can do by running the add-on SearchReset.

  I see that you have the extension of new tools tab, which should be in your modules Manager Ctrl + Maj + A > Extensions, but 'Request' can interfere with it.

  If your question is resolved by this or another answer, please take a minute to let us know. Thank you.

• confirmation letter you sent back twice and it does not appear on my yahoo account

  I created a Thunderbird e-mail account just to use only once for a project. He took everything on my yahoo Inbox, as well as a lot of junk and put it in the Inbox of Thunderbird. Then I closed the window and now do not know how to get to my Thunderbird account, do not know what my user name or password (or is it the same as my yahoo account?) I asked two emails from Thunderbird, but it is seems that they should be caught and transferred into the Thunderbird e-mail account (I can't seem to) and it does not appear in my yahoo Inbox. Yikes! Can someone help me?

  There is no such thing as a Thunderbird account so there is no username or password. Thunderbird is the e-mail client software that allows you to manage your real email account.
  There is no way to request emails from Thunderbird. Draw it will send you anything. It is a software running on YOUR computer.
  If your email account is with Yahoo then they are your provider and any loss of user name and or password must be sent with them.

• HP Simple pass Manager 6.0 does not work in Firefox 30

  I have been using HP Simple pass Manager 6.0 almost the entire Bill by paying websites. Recently my Firefox browser set to update Firefox 29 to 30 of Firefox. Now my HP Simple pass Manager 6.0 does not work in Firefox 30 in all.

  I contacted Mozilla Firefox and they said it's you plugin to increase the power of the fix. Is there a plugin fix soon?

  I rely on this program for extra protection.

  Thank you

  Chief

  Chief,

  Downgrade to the version of Firefox prior to Version 30 to allow the HP SimplePass extension to work.

  The instructions are below.

  The downgrade of the browser can disrupt the HP SimplePass database.  In fact roughly about everything upsets the HP SimplePass database.  The smile.

  Archives of Firefox

  Example: 26.0 for Windows download version (using a slightly different path for Mac)
  https://FTP.Mozilla.org/pub/mozilla.org/Firefox/releases/26.0/win32/en-us/

  ===========================================================================

  You can overload well enough, that is, install the old version of Firefox on the top of your new version.

  To be sure, export your bookmarks before making any changes in case something weird.

  • Create a Restore Point: create a restore - Win7 Point OR create a restore point Win8
  • Export your Firefox bookmarks
  • Download and install your selected version of Firefox

  Continue:

  • Close all your programs and shut down your computer
  • Unplug everything (little unifying for the keyboard / mouse external can stay)
  • Perform the Hard Reset for your model of laptop
  • Start the computer and connect

  Reminder: Hard Reset is just a device to reset.  The procedure do not destroy your files, or it destroys your Windows installation somehow.  It's just "clears the cobwebs".  Depending on the cause of the problem, this kind of "reset" can fix a variety of computer problems.

  If no joy:

  Open the Document of Dragon:

  HP SimplePass upgrade instructions

  Follow the procedures described in the guide for

  1. Export your Webcards
     
  2. Reinstall the driver of validity
  3. Restart / reboot the computer and log in
  4. Fix HP SimplePass program
  5. Restart / reboot the computer and log in

  Click on the Thumbs - Up Kudos to show that you appreciate the help and time of our Experts.

  Click on accept as Solution when the answer is a good solution or workaround!

  Although I strive to reflect best practices of HP, I do not work for HP.

• Error one of the UBS damage connected to this computer has malfunctioned and windows does not recognize it

  Original title: Canon MF 4500 printer inkjet

  My computer tells me that 'one of UBS damage connected to this computer has malfunctioned and windows does not recognize"it could the cable, as the printer (canon MF 4500) does not work.

  Hello

  1. what operating system is installed on your computer?

  2. when exactly you receive this error?

  3. all USB devices work properly on your computer?

  4. have you made changes on the computer before this problem?

  Method 1:

  You can try running the fix - it from the following link.

  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems/

  Method 2:

  You can try to uninstall and reinstall the USB controller. Follow the steps.

  (a) click Start and then click Control Panel.

  (b) click System and Maintenance, click System, and then click Device Manager.

  Note: If Control Panel is in Classic view, double-click System and then click on Device Manager.

  If you are prompted for an administrator password or a confirmation, type the password, or click on allow.

  (c) in Device Manager, double-click to expand the "USB Bus controllers", right click on the controller host, click "Uninstall" and click "OK".

  Check that if at all, there is an exclamation point on the pilot, it suggests problems with the installed driver.

  (d) repeat step 2 to uninstall all items under 'USB Bus controllers'.

  Then, restart your computer and Windows will automatically reinstall all USB controllers.

  It will be useful.

• My Vista system trying to download the updates, and it does not complete the download. It is up to "Windowsupdate_00000646" and "windowsupdate_dt000" How do I clear this code to receive these updates?

  My Vista system trying to download the updates, and it does not complete the download. It is up to "Windowsupdate_00000646" and "windowsupdate_dt000" How do I clear this code to receive these updates?

  They are only updated office or all updates?

  For Office updates, usually to pick up the item at the: http://www.microsoft.com/downloads/en/default.aspx

  then manually download and install the same.

  If all updates, perhaps consider the following general tips-

  Option: File of Windows Update agent wups2.dll is incorrectly registered and the registry associated with the Wups2.dll file files are missing.

  Method 1: Save the Windows Update files

  1. Click Start and type notepad in the box start the search.
  2. click on Notepad in the list programs.
  3. copy the following commands, and then paste them into the opened Notepad window:
  REGSVR32 WUPS2. DLL/S
  REGSVR32 STINKS. DLL/S
  REGSVR32 WUAUENG. DLL/S
  REGSVR32 WUAPI. DLL/S
  REGSVR32 WUCLTUX. DLL/S
  REGSVR32 WUWEBV. DLL/S
  REGSVR32 JSCRIPT. DLL/S
  REGSVR32 MSXML3. DLL/S
  4. in Notepad, on the file menu, click Save as.
  5. in the file type list, click all files.
  6. in the file name box, type register.bat.
  7. save the Register.bat file to your desktop.
  8 right-click the Register.bat file, and then click Run as administrator. If you are prompted for an administrator password or a confirmation, type the password or click on continue.
  9. try to reinstall updates.

  http://support.Microsoft.com/kb/958053
  See: method 1: save the Windows Update files

  http://support.Microsoft.com/kb/326253
  Method 5: Registry Windows Update engine files

  http://support.Microsoft.com/kb/971058
  How to reset the Windows Update components?

  Method 2: Download and install Windows Update agent

  Windows Update Agent

  How to get the latest version of the Windows Update Agent to help manage updates on a computer
  http://support.Microsoft.com/kb/949104

  Information for network administrators about how to obtain the latest Windows Update Agent
  http://support.Microsoft.com/kb/946928

  Click Start, click run, click Browse, navigate to the file you saved and click Open.

  Add the switch /wuforce at the end of the command run and then click OK. For example, the command run might look like this: "C:\WindowsUpdateAgent30-x86.exe" /wuforce

  Click run.

  Follow the steps to complete the wizard.

  Important

  To reinstall Windows Update Agent - download the relevant file from one of the links provided above and save it to a drive where Vista is not loaded because the file cannot be launched directly from the root directory of the system.

  Click Start, run, type: "D:\WindowsUpdateAgent30-x86.exe /wuforce" (without the quotes) and press ENTER to install the Windows Update engine.

  Note: There is a space between "D:\WindowsUpdateAgent30-x86.exe" and "/ wuforce.

  D: is the drive where Windows is not installed (IE a flash drive or a 2nd hard drive etc.)

  TaurArian [MVP] 2005-2010 - Update Services

• Why am I suddenly "USB not recognized, one of the devices USB has malfunctioned and Windows does not recognize"

  Hi all. If anyone out there in Cyber Land can solve this problem for me so I've personally you will issue an eight-pack of ice-cold beer (or a bottle of wine for the ladies lol)...

  I'll try not to waffle too guys, so here's...

  Right my PC running Windows XP. I also have itunes installed on my PC (I have an iphone 4). Upward until yesterday my iphone and itunes were working well, (once I plugged my iphone in the itunes USB port recognised that my iphone was plugged and synchronization was fine etc.).

  But now when I plug my iphone to PC to sync with itunes, I get a pop up box on the lower right part of the screen that reads... "USB not recognized one of the USB devices has malfunctioned, and Windows does not recognize."

  After visiting about 5 different sites now "Ways to solve this problem", believe it or not, I still have the problem bloody! :(

  A site proposed shutdown PC and unplug it from the power supply, then plug it back start-up and back... this as did not work!
  The other they say that I should go to Device Manager, uninstall all the USBs then restart... it did not work either.
  Tried a system restore
  Tried to reinstall itunes

  When I check the names USB in Device Manager, there is one who reads unknown device. I am literally pulling what's left of my hair now. I tried to solve this problem for almost 2 days now and still no joy. That's why no matter what input you guys would be very appreciated. I'm no PC Wizard, so please, don't think you're patronizing me if you break down things step by step for me.

  Thank you comrades, cordially, Freddy frustrated. :)

  Another said I should go to Device Manager, uninstall all the USBs and restart.

  Usually, this works... but can be very dangerous, unless you have a PS/2 keyboard.

  I also assume that you have tried all other USB ports on the computer. tried a verified USB device (for example, a flash drive) in the USB usually when you plug in your iPhone. and I tried your iPhone in another computer (I know it's rare for an error message Windows really means what he says, but sometimes the material lacks).

  Is the charge of the iPhone when it is connected to the USB port (I don't think)?  This happened to me recently, but a reboot fixed it.  I guess that that happened to you.

  I guess that you don't see the error messages in Device Manager or you must declare them.

  You can uninstall all USB devices that do not exist as follows:

  • Open a command prompt window (start > run > cmd > OK)
  • Enter the following command and press enter

  Set devmgr_show_nonpresent_devices = 1

  • Start the Device Manager by typing the following in the same command prompt window

  devmgmt.msc

  • In Device Manager, click the view menu and select "Show hidden devices".
  • You should see a category just after "Non-Plug and Play drivers" named "other devices."  Chances are that there will be a big exclamation yellow mark beside it.  When you expand the "other devices" you should see several non identified "USB devices."  Uninstall all this.
  • Reboot (with the iPhone NOT connected).

• Startup and display does not work well.

  When I start Windows XP it takes about 4 minutes to the icons appears.  They appear of normal size and the screen turns white and the size of the icons and programs and the internet are extra-large. I go into display properties and reconfigure and find his game on 8-bit!  After configuration back to normal display and restart or turn on again the same thing happens!

  Also, I tried to do a system restore and it does not work either. Please advise me on what to do. Thank you!

  Hi RhondaHeaven,

  I suspect that your display card drivers are corrupted. You have your cd/dvd drivers? If this is not the case, download your display drivers (you will get the model and make from Device Manager - click on start-> settings-> Control Panel-> system-> hardware-> device-> display adapter Manager).

  Click Start-> settings-> Control Panel-> system-> hardware-> Device Manager-> right click on your display-> Uninstall adapter.

  Uninstall display drivers Intel of add/remove programs.

  Restart your computer. Reinstall the drivers from the cd or downloaded driver.

  I hope this helps.

• Error - "one of the usb devices attached to this computer has malfunctioned and windows does not recognize it

  Original title: USB device not recognized / dysfunction

  "Unrecognized USB device".
  One of the USB devices attached to this computer has malfunctioned and Windows does not recognize it. Help for this problem, click this message. »

  This is what I get AFTER that I had to reinstall windows XP because a virus has attacked my computer a little before avg and Microsoft security essentials picked it up and destroyed... I have reinstalled twice... then I changed discs since I have two... well, I get this message from my 2 external Seagate Freeagent and my Phillips mp3 go gear aria... player these devices work on the laptop from my friend and she is under vista. It seems that since then they have worked on my computer before they would always run. My mouse and my cam work fine and my Canon printer gets thus detected... a few readers who have the space that is made... Ive looked everywhere for a solution... even upgraded windows media 11 and is player went to service pack 3. restarted several times... tried dPower Management tab and tried to

  Open recognition of the USB device by using Device Manager.

  .. I am at a loss: P please help thanks!

  isable the power management of the USB hub and I couldn't find the

  Hi LadyDefi,

  You can try to uninstall and reinstall the USB controllers and check:

  To remove and reinstall all USB controllers, follow these steps:

  a. Click Start, click Run, type sysdm.cpl in the Open box and then click OK.

  b. click on the Hardware tab.

  c. click the Device Manager button.

  d. expand Bus USB controllers.

  e. right click on each device under the Bus USB controllers node and then click on uninstall to remove them one at a time.

  f. restart the computer and reinstall the USB controllers.

  g. plug in the removable USB storage device and test to make sure that the problem is solved

  For more information, see the following article:

  Advanced troubleshooting tips for General USB for Windows XP problems

  http://support.Microsoft.com/kb/310575

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Error "one of the USB devices attached to this computer has malfunctioned and Windows does not recognize it." when you connect Logitech M225

  Original title:

  My wireless mouse works fine for the last 2 months, now, all of a sudden it doesn't work at all.

  I get a windows notification that says-

  "One of the USB devices attached to this computer has malfunctioned and Windows does not recognize it."

  I have Vista 32 bit OS on my laptop.

  My office has Windows 7 32 bit and I am able to use the mouse on this computer, then the M225 is not defective.

  I tried to look for a download of update on the site of Logitech & only found:

  6.32.20 set - point it did nothing to help.

  I also tried to move the receiver to the other 2 ports USB w / still the same results.

  Are there other downloads or solutions that will help w / this problem?

  You can also try searching for devices strangers (with yellow symbols) in the Manager under the mouse devices and other pointing devices and other devices (if any). Right click and uninstall unknown devices. Then restart.

  Also try the steps below to reset the power of USB:
  (a) the laptop off, unplugged from the wall outlet.
  (b) remove the battery for a few minutes, then reinstall it.
  (c) then restart the laptop.

• Computer is very slow and IE does not work all the time.

  I bought a computer from my old employeer.  He is doing all sorts of things, or should I say not to do all sorts of things.  It is very slow and IE does not work all the time.  They have questions arise and ask if the administrator oks things and other things like that.  It came with any disks.  I would like to wipe, clean and load a new disc, but I don't know where to find the disc or if I can do it.   Can someone please?

  Hello

  Proceed as follows to contribute to these two questions. You can probably buy the disks of Vista machine to system or get
  the former employer to do it for you if necessary.

  Try these and it can also be a good idea to update your main drivers later. The General corruption can also play a
  role in this issue. And even the TCP/IP stack might need to be refreshed.

  What antivirus/antispyware/security products do you have on the machine? Be one you ALREADY had on this
  machine, including those you have uninstalled (they leave leftovers behind which can cause strange problems).

  If no joy there's something blocking perhaps.

  Start - All Programs - Accessories - System Tools - IE with no Addons - what works best?

  IE - Tools - Internet Options - Advanced - tab click on restore, and then click Reset - apply / OK

  IE - Tools - Internet Options - Security tab - click on reset all default areas - apply / OK

  Close and restart IE or IE with no addons

  not better?

  IE - tools - manage Addons (for sure disable SSV2 if it is there, it is no longer necessary but Java always install
  "(and it causes problems - you never update Java to go back in and turn it off again)." Search for other possible problems.

  Windows Defender - tools - software explore - look for problems with programs that do not look right. Permit
  are usually OK and "unauthorized" are not always bad. If in doubt about a program to ask about it here.

  Could be that a BHO - BHOremover - free - standalone program, needs no installation, download and run - not all
  are bad, but some can cause your question (toolbars are BHO).
  http://securityxploded.com/bhoremover.php

  Startup programs
  http://www.Vistax64.com/tutorials/79612-startup-programs-enable-disable.html

  Also get Malwarebytes - free - use as scanner only.

  http://www.Malwarebytes.org/

  --------------------------------

  Try these to erase corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  --------------------

  Departure - in the search box, type-> order

  at the top of the list to find COMMAND - CLICK RIGHT to it - RUN AS ADMIN

  Type the following commands (or copy and paste one at a time), each followed by pressing on enter.

  ipconfig/flushdns

  nbtstat-r

  nbtstat - RR

  netsh int Reinitialis

  netsh int ip reset

  netsh winsock reset

  RESET

  That resets your TCP/IP stack

  --------------------------------

  Maybe need of these:

  For drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
  Control Panel - Device Manager - Display Adapter - note the brand and complete model of your
  video card - double - tab of the driver - write version information. Now click on UPdate Driver (this
  cannot do anything as MS is far behind the certification of drivers) - then do a right click - Uninstall - REBOOT
  This will refresh the driver stack.

  Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party with their
  own the software and drivers and all other main drivers that you have.

  Now go to the site of the manufacturer of system (Dell, HP, Toshiba as examples) (restoration) and then of the manufacturer of the device
  (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for the BIOS, Chipset and software)
  updates on the site of the manufacturer of the system here.)

  Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after each installation.

  Repeat to the manufacturers - BTW on device at the DO NOT RUN THEIR SCANNER - manually check by model.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  If you update the drivers manually, then it's a good idea to disable the facilities of driver in the Windows updates,
  This leaves ONE of Windows updates, but it will not install the drivers who are generally older and cause
  questions. If updates offers a new driver and then hide it (right click on it) and then go look for new ones
  manually if you wish.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  Hope these helps.

  Rob - bicycle - Mark Twain said it is good.

• The Manager.exe HPConnection does not load correctly. An error message is displayed each time

  Hello

  I have recently upgraded to windows 8 and since then, I have a problem.

  The Manager.exe HPConnection does not load correctly. An error message is displayed every time that restarting the laptop.

  Would you please guide me how to solve this problem.

  Thank you in advance and I look forward to hearing from you soon

  Best wishes

  Hello

  Try the following

  Firstly, uninstall your current version of HP Support Assistant using Microsoft 'Fixit' at the following link: this is particularly useful for correcting problems that may prevent resettlement on the machines running a 64 bit OS.

  http://support.Microsoft.com/mats/Program_Install_and_Uninstall

  When this has completed, restart the laptop.

  Then download and install the latest version of HP Support Assistant of the page on the link below - the download links are to the bottom of the page.

  http://h18021.www1.HP.com/helpandsupport/HP-support-Assistant.html

  After installation, restart the computer again.

  Kind regards

  DP - K